FULL MOON DISTORTION
17
LEDs
9V DC
INPUT
18
6 87
5
4
HI-TREB MIDDLE BASS
LEVEL GAIN
3
2
FULL MOON DISTORTION
1
BYPASS BOOST
1. Bypass Footswitch
2. Jewel Indicator
3. Output Jack
4. Level
5. Hi-Treble
6. Treble
7. Boost
8. Boost LED
9. Middle
9
TREBLE
BITETEXTURE
BOOST
10. Bass
11. Gain
12. Bite Switch
13. Texture Switch
14. Input Jack
15. Boost Footswitch
16. Low Battery Indicator
17. LED Kill Switch
18. DC Power Connector
10
11
12
13
14
15
16
FULL MOON DISTORTION
Thanks for purchasing the Full Moon Distortion —
a high gain distortion pedal with flexible tone
shaping capabilities. Engineered to deliver heavy
distortion without losing clarity, the Full Moon is
equipped with a four-band EQ to help match this
pedal to any guitar/amp combination. The
Texture and Bite Switches offer additional tools to
tweak your sound. The Full Moon also offers a
boost that can increase the overall volume.
Between the EQ section, toggles, and boost, this
distortion pedal is capable of adding snarl to
chugging rhythms or creating soaring single-note
leads.
DESIGNED IN CALIFORNIA, U.S.A.
Level
This control adjusts overall volume level.
Hi-Treble
A useful control for smoothing out high gain. It softens the upper
frequencies and works to blend in the right amount of sizzle.
Treble
This controls the pedal’s high-frequency response. Dial it in to keep
the top end of your notes clear and defined.
Middle
This controls the pedal’s midrange response. A versatile control useful
in all distortion settings.
Bass
This controls the pedal’s low-frequency response. Use this to fatten up
thinner-sounding guitars, or roll it back to clear up guitars with too
much bottom end.
Boost
This control adjusts the amount of volume added when the Boost is
engaged.
Boost LED
This LED shows when the Boost is engaged.
Gain
This control adjusts the amount of distortion or saturation.
Texture Switch
This toggles between asymmetrical and symmetrical clipping.
Bite Switch
This switch adds extra gain at upper frequencies, reducing potentially
boomy low end and lets your instrument cut through the mix.
Jewel Indicator
The Jewel Indicator shows when the distortion effect is active
Bypass Footswitch
This rugged footswitch bypasses the effect.
Boost Footswitch
This switch provides extra output level set by the Boost control.
Input Jack
This is a high-impedance input suitable for electric guitar, bass,
keyboards and other instruments.
Output Jack
This is a low-impedance output jack that connects to the amp or to
the next effect pedal in the signal chain.
DC Power Connector
This is a standard center-negative 9VDC jack for use with
appropriate power supplies.
LED Kill Switch
This switch extinguishes the LEDs that illuminate the control
knobs—useful in maximizing battery life when running the pedal from
batteries.
Low Battery Indicator
This red LED on the front of the battery door illuminates when battery
voltage drops below a set threshold, indicating that the battery
should be replaced soon.
FENDER MUSICAL INSTRUMENTS CORPORATION
A PRODUCT OF:
CORONA, CALIFORNIA, USA
Fender® is a registered trademark of FMIC.
Copyright © 2018 FMIC. All rights reserved.
P/N 7714183000 - REV A
Important Safety Instructions
•WARNING: To prevent damage, fire or shock hazard, do not expose the unit or its AC
power to rain or moisture.
•Do not alter the AC plug of the connected power adapter
•Do not drip or splash liquids on the unit.
•No user serviceable parts inside, refer servicing to qualified personnel only.
• WARNING: The unit must only be connected to a safety agency certified, regulated,
power source (adapter), approved for useand compliant with applicable local and
national regulatory safety requirements.
• Unplug the AC power adapter before cleaning the unit exterior. Use only a damp cloth
for cleaning and then wait until the unit is completely dry before reconnecting it to power.
• Amplifiers and loudspeaker systems, and ear/headphones (if equipped) are capable
of producing very high sound pressure levels which may cause temporary or permanent
hearing damage. Use care when setting and adjusting volume levels during use.
Languages
Manual available in Espanol, francais, Italiano, Deutch, Portugues, (Chinese)
www.fender.com/support
IMPEDANCES:
POWER SUPPLY:
POWER REQUIREMENTS:
DIMENSIONS:
WEIGHT:
Product specifications subject to change without notice
Specifications
INPUT: 500kΩ OUTPUT LOAD: >10kΩ
One 9V battery or 9VDC regulated adapter,
5.5 x 2.1 mm barrel connector, center negative
80mA @ 9VDC
110mA, Total Current Consumption
3.75” x 4.9” x 2.5” (95.25mm x 124.5mm x 63.5mm)
1.2lbs (.54kg)
NOTES:
© FENDER MUSICAL INSTRUMENTS 2018
Loading...