Fantech FKD 8XL, FKD 10XL, FKD 12S, FKD 10, FKD 12 Installation And Maintenance Instructions Manual

...

Page 1

INST ALLATION AND MAINTENANCE INSTRUCTIONS FOR MODEL FKD

Call 1-800-667-8721 anywhere in the US and Canada - www.rangehoods.com

1. The compactness and adaptability of the FKD Series fans permit

1. The compactness and adaptability of the FKD Series fans permit easy installation. The fans are shipped fully assembled and can be

easy installation. The fans are shipped fully assembled and can be mounted at any angle.For various mounting, see figures on the

mounted at any angle.For various mounting, see figures on the following page.

following page.

2. Because this unit has rotating parts,safety precautions should

2. Because this unit has rotating parts,safety precautions should be exercised during all phases of installation,operation and

be exercised during all phases of installation,operation and maintenance.

maintenance.

3. CAUTION: “For General Ventilation Use Only. Do Not Use To

3. CAUTION: “For General Ventilation Use Only. Do Not Use To Exhaust Hazardous Or Explosive Material and Vapors.”

Exhaust Hazardous Or Explosive Material and Vapors.”

4. Remove unit from package and inspect within 15 days after

4. Remove unit from package and inspect within 15 days after receipt.If damaged, report damage to carrier.Do Not operate

receipt.If damaged, report damage to carrier.Do Not operate this unit with visible damage to the blower or impeller

this unit with visible damage to the blower or impeller assembly.

assembly.

5. CAUTION: “This unit has an unguarded impeller.Do not use

5. CAUTION: “This unit has an unguarded impeller.Do not use in locations readily accessible to people or animals.” WEAR

in locations readily accessible to people or animals.” WEAR

HAND PROTECTION AND STAY CLEAR OF SHARP

HAND PROTECTION AND STAY CLEAR OF SHARP EDGES!

EDGES!

6. Screen guards must be installed within reach of personnel,

6. Screen guards must be installed within reach of personnel, within (7) feet of the working area,or when advisable for safety.

within (7) feet of the working area,or when advisable for safety.

7. PLEASE read the entire manual before installing.

WARNING

Before installation,servicing or cleaning unit,switch power off at serv-

Before installation,servicing or cleaning unit,switch power off at service panel and lock the service disconnecting means to prevent power

ice panel and lock the service disconnecting means to prevent power from being switched on accidentally. When the service disconnecting

from being switched on accidentally. When the service disconnecting means cannot be locked,securely fasten a prominent warning device,

means cannot be locked,securely fasten a prominent warning device, such as a tag,to the ser vice panel.

such as a tag,to the ser vice panel.

WARNING

Fan Tech at

kitchen

U N L I M I T E D

accessories

Page 2

rangehoods

.com

Mounting Illustration 1

Detail

Vibration

Mount

Call 1-800-667-8721 anywhere in the US and Canada

Please follow all applicable codes when installing this unit

1.Equipment should be hung at its proper elevation by using temporary fixtures that can be removed after vibration hangers are installed.

2.Hanger may be fastened directly to the structure or somewhere between suspended unit (be sure not to over tighten the neoprene element).

3.Install hangers.

4.Turn nuts on rod assembly clockwise one complete turn on each hanger. Repeat this procedure until temporary hanging fixtures are loose and load of piping or equipment is suspended completely on the vibration hangers.

5.Remove temporary hanger fixtures and level piping or equipment by taking additional turns on the spring/top hanger rod nut – clockwise to raise,counterclockwise to lower as required.

6.If equipping fan with isolators (FC Clamps), they should be attached at this time.

7.See wiring section to complete installation.

- www.rangehoods.com

Mounting Illustration 2

Mounting Illustration 3

Mounting

Bracket

Fan

Bracket

Vibration

Mounts

Please follow all applicable codes when installing this unit

1.Install wood supports to structure for fan mounting.

2.If equipping with vibration mounts, attach to supports.

3.Attach fan to vibration mounts (be sure not to overtighten the neoprene element).

4.If equipping fan with isolators (FC Clamps), they should be attached at this time.

5.See wiring section to complete installation.

Please follow all applicable codes when installing this unit

1.Create/Install angle wood supports to structure for fan

mounting.

2.If equipping with with vibration mounts, attach to supports.

3.Attach fan to vibration mounts (be sure not to overtighten

the neoprene element).

4.If equipping fan with isolators (FC Clamps), they should be

attached at this time.

5.See wiring section to complete installation.

Please Note:Vibration Mounts and Hardware are not supplied with fan.FC Clamps are sold separately.

Detail

Fan Tech at

kitchen

U N L I M I T E D

accessories

Page 3

rangehoods

.com

Call 1-800-667-8721 anywhere in the US and Canada

Dimensions and Wiring (Models FKD 8XL, 10,10XL, 12S, 12,14S)

- www.rangehoods.com

3⁄4”

Dimensional Data

Model A C D E Weight

FKD 8XL 8 12¹⁄₂ 15¹⁄₂ 7 19 lbs.

FKD 10 10 12¹⁄₂ 12¹⁄₂ 7 21 lbs. FKD 10XL 10 14 15 8 15 lbs. FKD 12S 12 12¹⁄₂ 10 7 22 lbs. FKD 12 12 14 12¹⁄₂ 8 16 lbs.

FKD 14S 14 14 † 816lbs.

All dimensions in inches. † FKD 14s overall length is 8”

Dimensions and Wiring (Models FKD 12XL, 14,14XL, 16, 16XL,18, 18XL,20)

Dimensional Data

Model A A1 A2 B B1 C D E F G H Weight

FKD12XL 12 - 12 17⁷⁄₈ 20¹⁄₄ 18⁷⁄₈ ⁷⁄₈ 1⁵⁄₈ 4 7³⁄₄ ³⁄₈ 45 lbs.

FKD14 14 - 14 19³⁄₄ 22¹⁄₈ 20¹⁄₄ 1¹⁄₂ 1⁵⁄₈ 4 11¹⁄₈ ³⁄₈ 45 lbs.

FKD14XL 14 - 14 19³⁄₄ 22¹⁄₈ 20¹⁄₄ 1¹⁄₂ 1⁵⁄₈ 4 11¹⁄₈ ³⁄₈ 55 lbs. FKD16 16 16 - 19³⁄₄ 22¹⁄₈ 18¹⁄₄ 1¹⁄₂ 1⁵⁄₈ 4 9¹⁄₂ ³⁄₈ 55 lbs. FKD16XL 16 - 16 22¹⁄₈ 24³⁄₈ 23¹⁄₄ 1¹⁄₄ 1⁵⁄₈ ⁷⁄₈ 8¹⁄₂ ¹⁄₂ 85 lbs. FKD18 18 18 - 22¹⁄₈ 24³⁄₈ 21³⁄₄ 1¹⁄₄ 1⁵⁄₈ ⁷⁄₈ 7 ¹⁄₂ 85 lbs. FKD18XL 18 - 18 28¹⁄₈ 30³⁄₈ 30⁵⁄₈ 2 1³⁄₄ ⁷⁄₈ 12¹⁄₂ ¹⁄₂ 95 lbs.

FKD20 20 20 - 28¹⁄₈ 30³⁄₈ 30⁵⁄₈ 2 1³⁄₄ ⁷⁄₈ 10¹⁄₂ ¹⁄₂ 95 lbs.

All dimensions in inches. † FKD 14s overall length is 8”

115 Volt Single Phase Fans

115/230 Volt Single Phase Fans

Wiring schematic for 4 lead motors,single phase

Notes:

1. All leads are color coded as well as identified with an Alpha/Alpha or Alpha / Numeric code (i.e. TK or Z2).This code may be shown as a band on the wire or on a schematic on the motor hub.Colors should be verified against code band.If code band and color do not correspond to schematics above,wire according to the code on the band.

2. Color of capacitor leads may be reversed. Fan operation will not be affected.

230 Volt Three Phase Fan

Notes:

1. Contactor should be used. Control coil should be wired in series with motor thermal contacts (TK leads) as shown in diagram to provide thermal motor protection.

2. All leads are color coded as well as identified with a band containing an Alpha/Alpha or Alpha/Numeric code (i.e.TK or Z2).Colors should be verified against code band.If code band and color do not correspond to schematics above,wire according to the code on the band.

Motor Leads

Green/Yellow ( )

U2 V2

U1 V1

TK TK

(Ground)

Line 1 Line 2

Supply

Voltag

Line 3

Fan Tech at

460 Volt Three Phase Fan

Notes:

1. Contactor should be used. Control coil should be wired in series with motor thermal contacts (TK leads) as shown in diagram to provide thermal motor protection.

2. All leads are color coded as well as identified with a band

Green/Yellow ( )

Motor Leads

TK TK

containing an Alpha/Alpha or Alpha/Numeric code (i.e.TK or Z2). Colors should be verified against code band.If code band and color do not correspond to schematics above,wire according to the code on the band.

Contactor for 3-Phase Fans, 208-230/460v

Incoming

3-Phase Supply 208/230/460

Control Power

for Contactor

kitchen

U N L I M I T E D

accessories

T1 T2 T3

TK TK L1 L2 L3 L3

Motor Leads

AC Contacto

L2 L3

Ground

Line 1 Line 2 Line 3

(Ground)

Supply

Voltag

Page 4

rangehoods

.com

Call 1-800-667-8721 anywhere in the US and Canada - www.rangehoods.com

Three (3) Year Warranty

This warranty supersedes all prior warranties

FANTECH,INC. will repair or replace any part of your product that has a factory defect in workmanship or material.Product must be returned to point of purchase,with Bill of Sale, within three (3) years of purchase. If factory return is required,as determined by rep/distributor, the warrantee assumes all cost to and from the factory.

THE FOLLOWING WARRANTIES DO NOT APPLY:

a)To damages from shipping,either concealed or visible; b) To damages resulting from improper wiring or

installation;

c)To damages or failure caused by Acts of God, or

resulting from improper consumer procedures such as

1) improper maintenance,

2) misuse , abuse, abnormal use,or accident and

3) incorrect electrical voltage or current; d) To removal of or any alteration to the Fantech label,

control number or date of manufacture;

e)To any other warranty, expressed,implied or written,

and to any consequential or incidental damages,loss of property, revenues,or profit or costs of removal,or reinstallation,for any breach of warranty.

W ARRANTY VALID A TION

The end user must keep a copy of the Bill of Sale to verify purchase date.Valid proof of the date of installation may also serve as a verification of commencement of warranty period.

FANTECH RETURN POLICY

Claims for damages or shortages must be reported within ten (10) days of receipt of product(s). For any product(s)

received damaged by the forwarding agent,THE FOLLOWING INSTRUCTIONS MUST BE FOLLOWED:

1) For product delivered by UPS:

a)Concealed Damages:Keep all cartons. Call UPS for an inspection and notify Fantech immediately. b)Visible Damages:Save all cartons and file complaint directly with UPS.

2) For product delivered via a common carrier:File

damaged goods claim directly with the freight company.

3) Shor tages: Sign only for the total number of pieces

received and call Fantech immediately.

FOR FACTORY RETURN

Product(s) returned without authorization will not be accepted.Fantech will not accept the return of any special, non-stock,obsolete or unsalable product(s). Fantech may, at its option,accept return of salable product(s) subject to a 25% restocking charge.

1) No product(s) will be accepted without a Return Materials

Authorization (RMA) number. This number can be obtained by calling Fantech,Inc.at 800-747-1762. Please have Bill of Sale or proof of date of installation available.

2) RMA must be clearly marked on outside of carton or

delivery will be refused.All product(s) must be returned freight prepaid.

3) Product(s) will be repaired/replaced and shipped back to

buyer; no credit will be issued.

4) Any out of warranty product will be evaluated and buyer

will be notified of cost;repair cost will be charged to customer; buyer will be responsible for return freight or product may be returned without action,to the buyer,freight collect.No credit will be issued.

Limitation of Warranty and Liability

This warranty does not apply to any FANTECH product or part which has failed as a result of faulty installation or abuse, incorrect electrical connections or alterations made by others,or use under abnormal operating conditions or misapplication of the product or parts.We will not approve for payment any repair not made by us or our authorized agent without prior written consent. The foregoing shall constitute our sole and exclusive warranty and our sole exclusive liability, and is in lieu of any other warranties, whether written,oral implied or statutory.There are no warranties which extend beyond the description on the page hereof.In no event,whether as a result of breach of contract,or warranty or alleged negligence, defect incorrect advice or other causes,shall FANTECH be liable for special or consequential damages,including, but not limited to, loss of profits or revenue, loss of use of equipment or any other associated equipment, cost of capital,cost of substitute equipment, facilities or services,downtime costs, or claims of customers of purchase for such damages.FANTECH neither assumes or authorizes any person to assume for it any other liability in connection with the sale of product(s) or part(s).Some jurisdictions do not allow the exclusion or limitation of incidental or consequential damages so the above limitations and exclusions may not apply to you.

Warning

FANTECH,INC. products are designed and manufactured to provide reliable performance, but they are not guaranteed to be 100% free from defects.Even reliable products will experience occasional failures and this possibility should be recognized by the user. If these products are used in a life support ventilation system where failure could result in loss or injury,the user should provide adequate backup ventilation,supplementar y natural ventilation,failure alarm system, or acknowledge willingness to accept the risk of such loss or injury.

Fan Tech at

kitchen

U N L I M I T E D

accessories