Fagor HTT 101 User Manual

HTT 101

HDMI/YPbPr/S

Encoder Modulator

-Video/AV to

DVB

-T

TABLE OF CONTENTS

1. SPECIFICATIONS .............................................................................................................................. 3

1.1 Product Overview ..................................................................................................................... 3

1.2 Appearance and Description .................................................................................................... 3

1.3 System Diagram ........................................................................................................................ 4

1.4 Characteristics .......................................................................................................................... 4

2. Installation Guide and Safety Instructions ..................................................................................... 5

2.1 Safety Instructions .................................................................................................................... 5

2.2 Installation ................................................................................................................................ 5

3. Operation ....................................................................................................................................... 7

3

1. SPECIFICATIONS

1.1 Product Overview

HTT Home encoder & modulator allows audio/video signal input in TV distributions with

applications in home entertainment, surveillance control, hotel Digital Signage, shops etc.
It is an all-in-one device integrating MPEG4 AVC/H.264 encoding and DVB-T modulating to
convert input signals to DVB-T RF out in the frequency range of 30~960MHz.
The signals source could be from satellite receivers, closed-circuit television cameras, Blue-ray
players, and antenna etc. its output signal is to be received by DVB-T standard TVs or DVB-T
STBs etc.

1.2 Appearance and Description

Grounding: to connect the earth cable
DC 12V: power input
HDMI: HDMI stream input supporting HD signals
YPbPr/S-Video/AV: YPbPr/S-Video/AV signal input through a VGA adapter cable
RF in: RF Loop-through input (10dB attenuation)
RF out: RF output to distribute modulated signal (30-960 MHz, 71~91 dBµV)

LCD Window

Control Buttons

JTAG port for upgrade

Air Vent

Indicators

RF out

HDMI in

DC 12V

RF

in

YPbPr/S-Video/AV in

Grounding

Air Vent

1.3 System Diagram

1.4 Characteristics

Encoding Section

HDMI

Video

Encoding MPEG-4 AVC/H.264

Interface HDMI

Resolution

1920*1080_60P,1920*1080_50P;

1920*1080_60i, 1920*1080_50i;

1280*720_60p, 1280*720_50P

Bit rate 0.500~19.500 Mbps

Audio

Encoding MPEG1 Layer II, (MPEG2-AAC, MPEG4-

AAC available)

Interface HDMI

Sample rate 48KHz

Bit rate

64, 96,128, 192, 256, 320, 384kbps

YPbPr/

CVBS/

S-Video

Video

Encoding MPEG-4 AVC/H.264

Interface CVBS *1, YPbPr*1, S-Video*1

Resolution

CVBS & S-Video: 720x576_50i (PAL);

720x480_60i (NTSC)

YPbPr: 1920*1080_60i, 1920*1080_50i;

1280*720_60p, 1280*720_50P

Bit rate

0.500~19.500 Mbps

Audio

Encoding MPEG1 Layer II, (MPEG2-AAC, MPEG4-AAC

available )

Interface 1*Stereo /mono

Sample rate 48KHz

Bit rate

64, 96,128, 192, 256, 320, 384kbps

Modulator Section

Standard DVB-T COFDM

Bandwidth 6M, 7M, 8M

Constellation QPSK, 16QAM, 64QAM,

Code rate 1/2, 2/3, 3/4, 5/6, 7/8.

Guard Interval 1/32, 1/16, 1/8, 1/4.

Transmission Mode: 2K, 8K

MER ≥42dB

RF frequency 30~960 MHz, 1KHz step

RF output level -16~ -36 dBm (71~91 dBµV), 0.1db step

System

Management

Local control: LCD + control buttons

Language E

nglish

LCN Insertion yes

Upgrade JTAG

General

Power supply

DC 12V

Dimensions 153

*11

Weight < 1kg

Operation temperature

0~45

℃

2

. Installation Guide

2.1 S

afety Instructions

WARNING:

To prevent fire or electrical shock, do not expose the device to rain or moisture

The encoder modulator is powered with

must not exceed the recommended voltage, which otherwise may cause irreparable damage

to the device and the invalidation of the warranty. Therefore:



Do not replace power supply with a voltage greater than 12V



Do not connect the device to the power if the power cord is damaged.



Do not plug the device into mains supply until all cables have been connected correctly.

 Do not cut the cord.

Avoid placing the device next to central heating components and in a

humidity.

Do not cover the device with elements that obstruct the ventilation slots.

If the encoder modulator has been kept in cold conditions for a long time, keep it in a warm

room minimum 2 hours before plugging into the mains.

Mount the

device in vertical position with the connectors located on the top side.

When replacement parts are required, be sure the service technician has used replacement

parts specified by the manufacturer or have the same characteristics as the original part.

U

nauthorized substitutes may result in fire, electric shock or other hazards.

Safety check-

Upon completion of any service or repairs to this device, ask the service

technician to perform safety checks to determine that the device is in proper condition.

2.2 Installation

RISK OF damage to the unit

Mechanically handling the unit may result in

supply before or during assembly.

0*50mm

and Safety Instructions

a voltage of 12V DC. The power supply

DC.

damage. Do not connect the unit to the power

Connect the unit as below instructed.

5

.

voltage

reas of high

1. Mount and tighten the screws and

plugs to secure the unit to the wall.
Left 10 cm of free space around from
each unit.

2. Connect the signal input in the respective connectors. The signal source can be from a

surveillance monitor, DVD, set-top box, CCTV and etc.

3. Optionally, connect the

loop-through RF input
coaxial cable.

4. Connect cable to RF output to

STB/TV.

5. Power supply connection: a) Connect the earth cable; b) Connect the power plug to the

unit mains connector; c) Connect the power plug to the mains socket.

Cascade Installation

HTT Home unit has 1 TV signal to RF output encoded as DVB-T Digital TV signal.
Several HTT Home units can be
cascaded in order to increase the
capacity. To cascade 2 or more units,
connect the RF output of the
preceding unit to the TV input
(loop-through) of the next unit (see
right illustration).

2

3

4

5

1

7

3. Operation

HTT HOME is controlled and managed through the key board and LCD display.

LCD Display – It presents the selected menu and the parameter settings. The backlight in the
display is on when the power is applied.
LED – These lights indicate the working status

 Power: It lights on when the power supply is connected.
 Alarm: It lights on when there is error, such as the signal source loss.
 Lock: It lights on when the signal source connected and goes off when the signal lose.

Left/Right/Up/Down buttons – Use these buttons to turn the screen pages, shift the target
items by moving the triangle, or change the parameter settings in the program mode.
Enter – Use this button to enter a submenu or save a new setting after adjustment; press it to
start adjusting the value of certain items when the corresponding underline flash with Up and
Down buttons;

Press it to activate the hidden selections and change the setting with Up and Down (or Left
and Right) buttons.

Menu – Press this button to step back
Lock – Locking the screen / cancelling the lock state, and entering the main menu after the

initialization of the device. After pressing lock key, the system will question the users to save
present setting or not. If not, the LCD will display the current configuration state.
When the power is connected, the LCD will start to initialize the program. The LCD menu goes
as below chart.

9

1) DVB-T: modulating standard; XX.XXX MHz: the current output frequency; 576i: video
resolution of signal source; X.XX Mbps: the current encoding bit rate

2) Alarm Status: For example, if the CVBS cable disconnected, it will display Video 1 Not Lock
under this menu.

3) Uptime: It displays the working time duration of the device. It times upon power on.

4) Video Parameters: User can enter the items respectively to view the video status and signal

source resolution, and set the input interface. User can also adjust values of rest items (Bit
rate: 0.500~19.500 Mbps; Brightness & Contrast & Saturation: 0-255; Hue: -128 - +127)

5) Audio Bit rate: Select audio bit rate among 64, 96, 128, 192, 256, 320, 384 kbps.

Audio Format: Select audio format among MPEG2, LC-AAC and HE-AAC.

6) Program Information: User can enable or disable the program output under menu Program
Output. User can also enter the other items to edit the Service Name, Program Name,
Program Number, and PIDs of PMT, PCR, Video and Audio, and edit LCN (Logical channel

number). EIT Event – User can enter this menu to setup EIT (Event Information Table) for the
current and next program event. The EIT contains Start Year, Start Time, Duration, and Event
Name of the event. All the EIT information can be displayed on the TV screen on condition
that the EIT is chosen to insert (see explanation 10.).

7) TSID: (Transport Stream ID) User can view or adjust after enter this menu.

8) ONID: (Original Network ID)-User can view or adjust after enter this menu.

9) NIT: (Network Information Table) NIT table is a very important table for describing the

network and TS. User can enter the submenus displayed and edit the values or select the LCN
(Logical channel number) mode, and choose whether to insert the NIT. If user chooses to
insert the NIT, information (Network ID, Network Name, LCN Mode, Private Data and LCN
number of the program mentioned in explanation 6) will be added to the transport stream.

 NOTE: when the Private Data is set as 0*0, it is invalid.

10) EIT: EIT Insert - As mentioned above (6), the event information table can be chosen

whether to insert into the TS or not under this menu. If yes, the EIT information set above (6)
will be displayed on the TV screen. Language Code – to set the EIT language For example,
code of the English language is eng. If you set the code as eng, the EIT displayed will be in
English language.

11) Bandwidth: choose between 6M, 7M and 8M.

12) Constellation: DVB-T modulator contains 3 constellation modes – 64 QAM, QPSK and 16

QAM.

13) FFT (Transmission Mode): Select between 2K and 8K.

14) Guard Interval: Select among 1/32, 1/16, 1/8 and 1/4.

15) Code Rate: It refers to FEC-Forward Error Correction rate. It contains 1/2, 2/3, 3/4, 5/6 and

7/8.

 NOTE: The different combination of bandwidth, constellation, guard interval and code

rate (FEC) will form a different output code rate. Please refer to appendix table 2.

16) RF Frequency: Adjust it at range of 30 to 999 MHz. Set it according your regional situation
or inquire your local services.

11

17) RF Level: Adjust it at range of -16~ -36dBm.

18) RF On: User can choose to turn on or turn off the RF under this menu.

19) Bit Rate: User can read the current modulating bit rate and the maximum bit rate

20) Save Config: Yes/No-to save/give up the adjustment of setting.

21) Load Saved CFG: Yes/No-to load/ not to load the saved configuration.

22) Reset all sets: Yes/No-choose/not choose the factory’s default configuration.

23) LCD Time out: A time limit that LCD will light off. Choose among 5s, 10s, 45s, 60s, 90s and

120s (seconds).

24) Lock Keyboard: Choose Yes to set a password and lock the keyboard, then the keyboard
will be locked and cannot be applicable. It is required to input the password to unlock the key
board. This operation is one-off. (If forgetting your password, please use the universal code
“005599”.)

25) Serial Number: User can view the serial number of this device. It is read-only and unique

26) Version: It displays the version information of this device. Encoder Modulator: the name of

the device; SW: software version number; HW: hardware version number. User can also press
ENTER again to view the published time of this device.

Appendix

Modulation

Constellation

FEC

6MHz Bandwidth

7MHz Bandwid

th 8MHz Bandwidth

Guard Interval

Guard Interval

Guard Interval

1/4 1/8 1/16 1/32 1/4 1/8 1/16 1/32 1/4 1/8 1/16 1/32

QPSK

1/2 The weak ability of error

-

correcting and anti

-

interference in this area

6.03

2/3

6.03 5.80 6.45 6.83 7.03 6.64 7.37 7.81

8.04

3/4

6.22 6.58 6.78 6.53 7.25 7.68 7.91 7.46 8.29 8.78 9.05

5/6 6.22 6.91 7.31 7.54 7.25 8.06 8.53 8.79 8.29 9.22 9.76 10.05

7/8 6.53 7.25 7.68 7.91 7.62 8.46 8.96 9.23 8.71 9.68 10.25

10.56

16QAM

1/2 7.46 8.29 8.78 9.04 8.70 9.67 10.24 10.55

9.95 11.06 11.71 12.06

2/3 9.95 11.05 11.70 12.06 11.61 12.90 13.66 14.07 13.27 14.75 15.61 16.09

3/4 11.19 12.44 13.17 13.57 13.06 14.51 15.36 15.83 14.93 16.59 17.56 18.10

5/6 12.44 13.82 14.63 15.08 14.51 16.12 17.07 17.59 16.59 18.43 19.52 20.11

7/8 13.06 14.51 15.36 15.83 15.24 16.93 17.93 18.47 17.42 19.35 20.49 21.11

64QAM

1/2 11.19 12.44 13.17 13.57 13.06 14.51 15.36 15.83 14.93 16.59 17.56 18.10

2/3 14.92 16.58 17.56 18.09 17.41 19.35 20.49 21.11 19.91 22.12 23.42 24.13

3/4 16.79 18.66 19.76 20.35 19.59 21.77 23.05 23.75 22.39 24.88 26.35 27.14

5/6 18.66 20.73 21.95 22.62 21.77 24.19 25.61 26.39 24.88 27.65 29.27 30.16

7/8 19.59 21.77 23.05 23.75 22.86 25.40 26.89 27.71 26.13 29.03 30.74 31.67

Table 1 Channel output max. capacity in Mbps