Faber INHC29SS Specsheet

UPDATED 2011 MODEL - 600 CFM WITH ELECTRONIC CONTROLS
Inca HC SS
the high powered hideaway
high capacity insert
°
fits custom hoods 30” wide and up
°
stainless steel finish
°
600 cfm
°
2 halogen lights
°
3 speed LED electronic controls
°
10 minute intensive speed setting
°
dishwasher safe stainless grease filters
°
convertible to recirculating *
°
top or direct rear venting
°
built-in mounting system
°
sone range: 3.5 - 6.5
°
6” round duct
°
Built - In Collection
Standard Series
* it is highly recommended that professional style cooking always be vented to the outside.
Size | Color Model #
29 Stainless
INHC29SS
a
CFM Reducer Kit
c
For use in make up air environments where
c
an under 300 cfm hood is required. This kit reduces the ducting to 5” round and
e
reduces the cfm to under 300
s s
Liners
Create a perfectly-sealed, non-
o
combustible perimeter around the
r
Inca HC SS. Depth adjustable from 16” - 17 7/8”.
i
Standard Liner 30 Stainless
e
Standard Liner 36 Stainless
s
CFMRED
LINE30ST
LINE36ST
New backlit electronic controls with a blue LED light to indicate the current speed and lighting on/off
Charcoal Filters
For recirculating installations, high quality, heavy duty filters ensure the removal of smoke and odors from the kitchen. Some ductwork is required to exhaust the unit out of the cabinet.
FILTER1
p.o. box 435 • Wayland, MA 01778 • tel: (508) 358-5353 • fax: (508) 358-5730 • e-mail: info@faberonline.com • www.faberonline.com
Dimensional Diagrams
Side View
Cut-Out
Front View
Note: The Inca HC comes standard in the top vent position. The direct rear vent position can be achieved by rotating the blower housing.
Bottom View
Liners
Create a perfectly-sealed, non-combustible perimeter around the Inca HC SS. Designed for 30” and 36” wide installations. Depth adjustable from 16” - 17 7/8”.
Standard Liner 30 Stainless (LINE30ST) designed for 30” wide installations
Standard Liner 36 Stainless (LINE36ST) designed for 36” wide installations
Pre-Planning Your Installation - Important: Consult the installation instructions before you begin installing
this rangehood. The recommended height to install this hood off the cooktop is a minimum of 24” and a maximum of 30” for maximum effectiveness. Also consult the cooktop manufacturer’s recommendation.
Pre-Planning Your Ductwork - Important: Consult the installation instructions before you begin installing this rangehood.
Make your ductrun as straight and
short as possible. The ductrun should not exceed 35 equivalent feet if ducted with the required minimum of 6” round duct. Count 45º angles as 3 feet, 90º elbows as 5 feet, and 90º flat elbows as 12 feet.
For best results, use no more than three 90° elbows. Make sure that there is a minimum of 24” of straight duct between elbows if more than one is used. Do not install two elbows together. If you must elbow right away, do it as far away from the hood’s exhaust opening as pos­sible.
For more efficient airflow when venting to the rear: Rotate the Inca HC blower housing so that the 6” round exhaust outlet faces the back, rather than running ductwork up and elbowing back.
Recirculating Installations
For installations where ductwork to the outside of your home is impossible or highly impractical Charcoal Filters, which attach to the blower assembly, absorb smoke and odors.
cabinet
6” round
duct
hood
ceiling
vent grate
soft
cabinet
6” round
duct
hood
vent grate
Some ductwork must be installed to exhaust the rangehood back into the kitchen, either at the top of the cabinet or at
the face of the soft. A
plastic vent grate sup­plied with the rangehood can be used to cover the duct opening. This duct work must not terminate into a dead air space.
ceiling
WARNING!
before you begin installing this rangehood.
Product specifications are subject to change without notification. Consult the installation instructions
Rev. 07/11
Loading...