
84 - 84EG
Positive stops for 400 - 400EG
FAAC International Inc.
Headquarter & East Coast Operations
3160 Murrell Road
Rockledge, FL 32955
Tel. 800 221 8278
www.faacusa.com
FAAC International Inc.
West Coast Operations
357 South Acacia Avenue
Fullerton, CA 92831

INSTALLATION
Manual release the operator that the stop is going to be installed on and pull the piston rod out 4 to 6 inches.
See the installation manual for detailed instructions on manual releasing your operator.
With the piston extended as told above place the 6mm lock washers on the 6mm bolts supplied in the hardware
package. Align the holes of the bottom base plate with the 4 “towers” located on the front of the 400 operator.
Insert all 4 bolts and tighten with a 10 mm wrench. (See Fig. 1)
With the piston rod sticking through the bottom 2 plates, screw the square swivel joint (provided) and the jam nut
into the threaded end of the piston rod. This plate and swivel joint are to insure a square stopping point for the
closed position on an inward swing gate and square stopping point on an outwards swing gate. (See Fig. 2)
Continue to install the operator as instructed in it’s installation manual. When the operator is securely in place
then the stop can be adjusted.
Start by closing the gate all the way. Adjust the closed stop by loosening the jam bolts and sliding the plate in the
direction needed to hit the square swivel joint and stop the gate. Once the stopping point had been established
tighten the jam nuts securely with a couple of 13mm wrenches. Then move the gate all the way open and adjust
the open stop by loosening the jam nuts and sliding the plate in the direction needed to hit the square swivel joint
and stop the gate. Once the stopping point has been established tighten the jam bolts securely with a couple of
13 mm wrenches. (See Fig. 3)
Recheck that all nuts and bolts are tight and that the gates are stopping where desired.
Fig. 1
Model 84 - 84EG positive stops
2

LIMITED WARRANTY
To the original purchaser only:
FAAC International, Inc., warrants, for twentyfour (24) months from the date of invoice, the
gate operator systems and other related systems and equipment manufactured by FAAC
S.p.A. and distributed by FAAC International,
Inc., to be free from defects in material and
workmanship under normal use and service for
which it was intended provided it has been properly installed and operated.
FAAC International, Inc.’s obligations under
this warranty shall be limited to the repair or
exchange of any part of parts manufactured by
FAAC S.p.A. and distributed by FAAC International, Inc. Defective products must be returned
to FAAC International, Inc., freight prepaid by
purchaser, within the warranty period. Items
returned will be repaired or replaced, at FAAC
International, Inc.’s option, upon an examination
of the product by FAAC International, Inc., which
discloses, to the satisfaction of FAAC International, Inc., that the item is defective. FAAC
International, Inc. will return the warranted item
freight prepaid. The products manufactured by
FAAC S.p.A. and distributed by FAAC International, Inc., are not warranted to meet the
specic requirements, if any, of safety codes
of any particular state, municipality, or other
jurisdiction, and neither FAAC S.p.A. or FAAC
International, Inc., assume any risk or liability whatsoever resulting from the use thereof,
whether used singly or in combination with other
machines or apparatus.
Any products and parts not manufactured by
FAAC S.p.A. and distributed by FAAC International, Inc., will carry only the warranty, if any, of
the manufacturer. This warranty shall not apply to any products or parts thereof which have
been repaired or altered, without FAAC International, Inc.’s written consent, outside of FAAC
International, Inc.’s workshop, or altered in any
way so as, in the judgment of FAAC Interna-
tional, Inc., to aect adversely the stability or
reliability of the product(s) or has been subject
to misuse, negligence, or accident, or has not
been operated in accordance with FAAC International, Inc.’s or FAAC S.p.A.’s instructions
or has been operated under conditions more
severe than, or otherwise exceeding, those set
forth in the specications for such product(s).
Neither FAAC S.p.A. nor FAAC International,
Inc., shall be liable for any loss or damage
whatsoever resulting, directly or indirectly, from
the use or loss of use of the product(s). Without
limiting the foregoing, this exclusion from liability
embraces a purchaser’s expenses for downtime
or for making up downtime, damages for which
the purchaser may be liable to other persons,
damages to property, and injury to or death of
any persons.
FAAC S.p.A. or FAAC International, Inc., neither
assumes nor authorizes any person to assume
for them any other liability in connection with
the sale or use of the products of FAAC S.p.A.
or FAAC International, Inc. The warranty herein
above set forth shall not be deemed to cover
maintenance parts, including, but not limited to,
hydraulic oil, lters, or the like. No agreement to
replace or repair shall constitute an admission
by FAAC S.p.A. or FAAC International, Inc., of
any legal responsibility to eect such replacement, to make such repair, or otherwise. This
limited warranty extends only to wholesale customers who buy directly through FAAC International, Inc.’s normal distribution channels. FAAC
International, Inc., does not warrant its products
to end consumers.
Consumers must inquire from their selling dealer
as to the nature and extent of that dealer’s warranty, if any. This warranty is expressly in lieu of
all other warranties expressed or implied includ-
ing the warranties of merchantability and tness
for use. This warranty shall not apply to products or any part thereof which have been subject to accident, negligence, alteration, abuse,
or misuse or if damage was due to improper
installation or use of improper power source, or
if damage was caused by re, ood, lightning,
electrical power surge, explosion, wind storm,
hail, aircraft or vehicles, vandalism, riot or civil
commotion, or acts of God.
Model 84 - 84EG positive stops
4