Extron electronic IN1604 HD, IN1604 DTP User Manual

IMPORTANT:

E

I

KL

IN1604 DTP

H

AUDIO

R

L

R

J KM

Refer to www.extron.com for the complete

user guide, installation instructions, and

specifications before connecting the

IN1604 Series • Setup Guide

product to the power source.

The Extron IN1604 DTP and IN1604 HD Scaling Presentation Switchers are four input, HDCP-compliant video scalers that accept a wide variety
of audio and video formats. This guide allows an experienced user to set up and congure an IN1604 Series scaler. It covers how to perform basic
operations using the front panel controls and selected Simple Instruction Set (SIS™) commands.

NOTE: For full installation, configuration, menus, connector wiring, and operation details, see the IN1604 Series User Guide, at

www.extron.com.

Installation

Rear Panel Features

L

3214+V

TALLY OUT

CONTACT IN

1234G

REMOTE

100-240V ~ 0.5 A MAX

50-60 Hz

HDMI HDMI3

21 CONFIGURABLE

F

OUT

L

L

IN

12

HDMI

4

OUTPUT

R

SIG

LINK

R

OUT

HDBT

DTP

OVER TP

RS-232 IR

GRx

Tx RxTx

3214+V1234G

TALLY OUTCONTACT IN

RS-232

Tx Rx G

REMOTEAUDIOINPUT

IN1604 HD

LR

L

AUDIOOUTPUT

HDMI

R

RS-232

Tx Rx G

A

BC

G

MD

Power and Input Connections Output Connections Control Connections

AC power connector

A

Configurable analog 15-pin HD (VGA)

B

connector (input 1)

HDMI input connectors (inputs 2-4)

C

Unbalanced analog audio input connector

D

(input 1)

Balanced or unbalanced analog audio input

E

connector (input 2)

Balanced or unbalanced analog

F

audio output connector

TP output connector

G

(IN1604 DTP only)

TP output switch (IN1604 DTP only)

H

RS-232 and IR Over TP

I

connector (IN1604 DTP only)

HDMI output connector

J

(IN1604 HD only)

Contact closure connector

K

Tally connector

L

Remote RS-232 connector

M

Figure 1. Rear Panel Features (IN1604 DTP Shown Left and Unique IN1604 HD Features Shown Right)

Mounting and Cabling

Step 1 — Mount the device.

a. Turn off or disconnect all equipment power sources.

b. Mount the IN1604 Series scaler on top of a at surface using the provided rubber feet, under a table using an optional mounting kit for

under-the-desk mounting, or to a rack shelf using an optional rack shelf-mounting kit.

Step 2 — Connect inputs.

a. Connect an analog video source (RGB, YUV, S-video, or composite) to the 15-pin HD (VGA) connector (see gure 1, B)

b. Connect digital HDMI or DVI (with an appropriate adapter) sources to the HDMI connectors (C).

c. Connect an unbalanced analog audio source to the 3.5 mm, female TRS (tip-ring-sleeve) audio connector (D). See Audio Wiring on

page 3 for more details.

d. Connect a balanced or unbalanced audio source to the 5-pole captive screw connector (E). See Audio Wiring on page 3 for more

details.

1

IN1604 Series • Setup Guide (Continued)

12345678

Insert Twisted

Pair Wires

Pins:

Pin

1

2

3

4

5

6

7

8

Wire color

White-green

Green

White-orange

Blue

White-blue

Orange

White-brown

Brown

Wire color

T568A T568B

White-orange

Orange

White-green

Blue

White-blue

Green

White-brown

Brown

3214+V

e

Step 3 — Connect outputs.

a. Connect a balanced or unbalanced audio output device to the 5-pole captive screw connector (F).

b. For the IN1604 DTP, set the HDBT/DTP switch (H) depending on the type of device to be connected to the TP output connector.

HDBT position — Select this position if the receiving device is an HDBaseT-compatible device. The output is HDMI with embedded
audio plus RS-232 and IR.

DTP position — Select this position if the receiving device is an Extron DTP device. The TP output is compatible with a DTP receiving
device and consists of HDMI with embedded audio, analog audio, RS-232 and IR, and remote power.

ATTENTION: Position this switch BEFORE connecting the appropriate device to the TP connector. Failure to comply can

damage the endpoint.

ATTENTION : Positionnez le sélecteur AVANT de connecter l’appareil approprié au connecteur TP. Ne pas respecter cette

procédure pourrait endommager le point de connexion.

c. For the IN1604 DTP, connect a DTP receiver or HDBaseT-compatible device to the female RJ-45 connector (G). For cable wiring and

recommendations, see Twisted Pair Recommendations below.

d. To pass serial or infrared data to a DTP receiver from an IN1604 DTP, connect a control device to the RS-232 and IR Over TP captive

screw connector (I). For wiring details, see RS-232 and IR Over DTP Wiring (IN1604 DTP Only) on page 3.

e. For the IN1604 HD, connect a digital display to the HDMI output connector (J).

Step 4 — Connect control devices.

a. Connect contact closure devices or Extron “Show Me” cables (see the red pigtail on the “Show Me”

cable in the diagram to the right) to the Contact In 5-pole captive screw connector (see gure 1, K).

b. Connect tally devices or Extron “Show Me” cables (see the black pigtail on the “Show Me” cable in the

diagram to the right) to the Tally Out 5-pole captive screw connector (see gure 1, L).

c. For serial RS-232 control, connect a host device to the RS-232 5-pole captive screw connector on the

IN1604 DTP or the 3-pole captive screw connector on the IN1604 HD (see gure 1, M).

d. For control or conguration through USB, connect a host device to the front panel USB mini-B port

(see gure 2, B).

TALLY OUT

REMOTE

RS-232

Tx Rx G

Pigtail

CONTACT IN

1234G

Red

Black “Show Me” Cabl

Wiring Details

2

Step 5 — Connect power.

Connect a 100-230 VAC, 50/60 Hz power source to the AC power connector (see gure 1, A).

Twisted Pair Recommendations

Extron recommends using the following practices to achieve full transmission distances and reduce
transmission errors:

• Use Extron XTP DTP 24 SF/UTP cable for the best performance. At a minimum, Extron recommends

24 AWG, solid conductor, STP cable with a minimum bandwidth of 400 MHz.

• Terminate cables with shielded connectors to the TIA/EIA-T568B standard (see right).

• Limit the use of more than two pass-through points, which may include patch points, punch down

connectors, couplers, and power injectors. If these pass-through points are required, use shielded
couplers and punch down connectors.

ATTENTION:

• Do not connect these connectors to a computer or telecommunications network.

• Ne connectez pas ces ports à des données informatiques ou à un réseau de télécommunications.

• DTP remote power is intended for indoor use only. No part of the network that uses DTP remote power should be routed outdoors.

• L’alimentation DTP à distance est destiné à une utilisation en intérieur seulement. Aucune partie du réseau qui utilise l’alimentation

DTP à distance ne peut être routée en extérieur.

NOTE: When using shielded twisted pair cable in bundles or conduits, consider the following:

• Do not exceed 40% ll capacity in conduits.

• Do not comb the cable for the rst 20 meters, where cables are straightened, aligned, and secured in tight bundles.

• Loosely place cables and limit the use of tie wraps or hook-and-loop fasteners.

• Separate twisted pair cables from AC power cables.

TIA/EIA-T568B

Pin Wire Color

1 White-orange

2 Orange

3 White-green

4 Blue

5 White-blue

6 Green

7 White-brown

8 Brown