ExtremeMobility 802.11ax/ac/abgn Outdoor
AP560h Access Point
Overview of AP560h
The AP560h is a stadium-optimized Wi-Fi 6, 802.11ax/ac/abgn outdoor access
point. The AP560h access point caters to the stadium environment by
supporting high density of users and devices.
The AP560h access point offers flexible deployment options and can be
mounted to a pole, to a wall, and to other access points with software
selectable antennas, thereby ensuring exceptional mobile experience
throughout the stadium.
Note: The AP560h requires a minimum base firmware of WiNG 7.1.2.
Features
The AP560h access point has the following features:
• Radios: 2 radios (1 dual-band, 2.4GHz and 5GHz, and 1 band-locked 5GHz);
1 IoT Radio (2.4 GHz)
• Two Ethernet ports:
– 1 x 100/1000/2500/5000 Mbps auto-negotiation Ethernet port, RJ45
– 1 x 10/100/1000 Mpbs auto-negotiation Ethernet port, RJ45
• Dimensions: 11.3" x 18.9" x 3.5" (288 mm x 481 mm x 88 mm)
• LEDs: Two top-mounted LEDs
– All LEDs will be on during reset.
•One Reset button
•Security locks:
– One Kensington lock
– One security hangar lock
•Power: PoE 802.3at
• Antennas:
– Two software selectable internal antennas (30 and 70 degree
directional antennas)
• Temperature:
– -40°F to +131°F (-40°C to +55°C) operating temperature
– -40°F to +158°F (-40°C to +70°C) storage temperature
•Enclosure: Plastic only
Figure 1 Front View of AP560h
Ordering Information
Table 1 AP560h Ordering Information
Part Number Description
Cloud-ready, Dual 5GHz, Dual-band, Sensor radio, Dual
AP560h-FCC
Radio 802.11ax/ac/abgn, 4x4:4 MIMO Outdoor 11ax access
point. Internal 30deg/70deg Panel Antenna.
Domain: US
Verifying the AP560h Box Contents
Verify the contents of the box and ensure that the following items are
available:
Table 2 Contents of the AP560h Box
Quantity Item
1AP560h Quick Reference
1 Cloud Quick Start Card
1 AP560h access point
Mounting Options
AP560h can be mounted to a wall or to a pole by purchasing separate
mounting brackets which are described in the following table.
Table 3 AP560h Mounting Brackets Usage
Mounting
Bracket and
Part Number
WS-MBO-
POLE01
(#30520);
Bracket; Also
known as the
Pole mounting
bracket
MBO-ART02;
10" 2-Axis
articulating
mounting
bracket
Note: The AP560h cannot be installed without the mounting
brackets.
Wal l In sta ll Pole Install Notes
No Yes If the pole diameter is <= 1"
(25.4mm), use small cable
clamp. If the pole diameter
is between 5" - 7" (178mm),
use large cable clamp. For
any other pole diameter,
provide your own stainless
steel cable clamp. The
band must be 1/2” (12.7mm)
wide. The POLE01 bracket
can be used only when
paired with the MBO-ART02
bracket.
Yes Yes The articulating mounting
bracket is used with POLE01
bracket for pole install. The
wall must
be strong enough to
support the access point
during
inclement weather.
AP560t Access Point Bundle
AP560h access point can also be purchased as an overhead access point
bundle called AP560t along with the mounting brackets. The following table
provides the details:
Table 4 AP560t Ordering Information
Overhead Access
Part Number
AP560t-FCC
For AP560t installation instructions, refer to the ExtremeMobility AP560t
Access Point Quick Reference Guide in the Extreme Networks Documentation
Support site.
Point Bundle
•AP560h-FCC
Access Point
• 30520 (WS-MBOPOLE01) Bracket
•MBO-ART02
Extension Arm
Cloud-ready, Dual 5GHz, Dualband, Sensor radio, Dual Radio
802.11ax/ac/abgn, 4x4:4 MIMO
Outdoor 11ax access point.
Internal 30deg/70deg Panel
Antenna and Mounting Kit
Domain: US
Description
Professional Installation Instruction
Installation personal
This product is designed for specific application and needs to be installed by a qualified
personal who has RF and related rule knowledge. The general user shall not attempt to
install or change the setting.
Installation location
The product shall be installed at a location where the radiating antenna can be kept 36
cm from nearby person in normal operation condition to meet regulatory RF exposure
requirement.
External antenna
Use only the antennas which have been approved by the applicant. The non-approved
antenna(s) may produce unwanted spurious or excessive RF transmitting power which
may lead to the violation of FCC/IC limit and is prohibited.
Installation procedure
Please refer to user’s manual for the detail.
Warni ng : Please carefully select the installation position and make sure that
the final output power does not exceed the limit set force in relevant rules. The
violation of the rule could lead to serious federal penalty.
Instructions d'installation professionnelle
Installation
Ce produit est destine a un usage specifique et doit etre installe par un personnel qualifie
maitrisant les radiofrequences et les regles s'y rapportant. L'installation et les reglages ne
doivent pas etre modifies par l'utilisateur final.
Emplacement d'installation
En usage normal, afin de respecter les exigences reglementaires concernant l'exposition
aux radiofrequences, ce produit doit etre installe de facon a respecter une distance de 36
cm entre l'antenne emettrice et les personnes.
Antenn externe
Utiliser uniiquement les antennes approuvees par le fabricant. L'utilisation d'autres
antennes peut conduire a un niveau de rayonnement essentiel ou non essentiel
depassant les niveaux limites definis par FCC/IC, ce qui est interdit.
Procedure d'installation
War nin g: Avertissement: Choisir avec soin la position d'installation et
s'assurer que la puissance de sortie ne depasse pas les limites en vigueur. La
violation de cette regle peut conduire a de serieuses penalites federales.
Consulter le manuel d'utilisation.
Regulatory and Compliance Information
Safety Guidelines
This section contains notices that are intended to protect your personal safety
and prevent damage to the equipment.
Qualified Personnel:
Electrical Hazard: Only qualified personnel should perform
installation procedures. Within the context of the safety notes in this
documentation, qualified persons are defined as persons who are
authorized to commission, ground, and label devices, systems, and
circuits in accordance with established safety practices and
standards. A qualified person understands the requirements and risks
involved with installing electrical equipment in accordance with
national codes.
Federal Communications Commission (FCC) Notice
This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses, and can radiate radio
frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the interference by one of the
following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
Caution: Any changes or modifications not expressly approved by
the party responsible for compliance could void the user's authority
to operate this equipment.
This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions: (1) This device may not cause harmful interference,
and (2) this device must accept any interference received, including
interference that may cause undesired operation.
This transmitter must not be co-located or operating in conjunction with any
other antenna or transmitter.
This device meets all the other requirements specified in Part 15E, Section
15.407 of the FCC Rules.
War nin g: FCC Radiation Exposure Statement: This equipment
complies with FCC radiation exposure limits set forth for an
uncontrolled environment. This equipment should be installed and
operated with minimum distance 26 cm between the radiator and
your body.
European Waste Electrical and Electronic Equipment
In accordance with Directive 2012/19/EU of the European Parliament on waste
electrical and electronic equipment (WEEE):
1 The symbol above indicates that separate collection of electrical and
electronic equipment is required.
2 When this product has reached the end of its serviceable life, it cannot be
disposed of as unsorted municipal waste. It must be collected and treated
separately.
3 It has been determined by the European Parliament that there are potential
negative effects on the environment and human health as a result of the
presence of hazardous substances in electrical and electronic equipment.
4 It is the users’ responsibility to utilize the available collection system to
ensure WEEE is properly treated.
For information about the available collection system, please contact Extreme
Environmental Compliance at Green@extremenetworks.com.
(WEEE) Notice
ExtremeMobilityTM
Access Point
Quick Reference
AP560h-FCC
Notice
Copyright © 2019 Extreme Networks, Inc. All Rights Reserved.
Legal Notices
Extreme Networks, Inc. reserves the right to make changes in specifications
and other information contained in this document and its website without
prior notice. The reader should in all cases consult representatives of Extreme
Networks to determine whether any such changes have been made.
The hardware, firmware, software or any specifications described or referred
to in this document are subject to change without notice.
Trademarks
Extreme Networks and the Extreme Networks logo are trademarks or
registered trademarks of Extreme Networks, Inc. in the United States and/or
other countries.
All other names (including any product names) mentioned in this document
are the property of their respective owners and may be trademarks or
registered trademarks of their respective companies/owners.
For additional information on Extreme Networks trademarks, please see:
www.extremenetworks.com/company/legal/trademarks/
Documentation, Installation Videos, & Support
For product support, including Documentation and Installation Videos, visit:
www.extremenetworks.com/documentation
P/N 9036161-01