Extreme Networks AP510e Quick guide
Installing the ExtremeMobility Indoor 802.11 ax
AP510e Access Point
Overview of the AP510e
The AP510e is a next generation, indoor ceiling mount model enterprise class 802.11ax
access point. The “e” in AP510e indicates that it comes with external antennas. The AP
features a dual-band radio, a band locked radio, eight RP-SMA WiFi ports, one Bluetooth
port, and one internal Bluetooth Low Energy (BLE) antenna. The Bluetooth port can be
used for a remote antenna in place of the internal antenna.
The AP510e can be mounted on a dry or wood wall, solid flat ceiling, junction/gang box,
and on a suspended or drop ceiling.
Note: The AP510e requires a minimum base firmware of WiNG 7.1.1.
The AP510e model has the following features:
• Radios: 2 radios (1 dual band, 2.4GHz and 5GHz, and 1 band locked 5GHz); 1 IoT radio
(2.4 GHz)
•Console Port: RJ45
•Two Ethernet Ports
– One multi-rate GE/2.5GE/5GE port (LAN1) with PoE In
– 10/100/1000 Ethernet Port (LAN2) with PoE In
•LEDs: 6
– All LEDs will be on during reset.
• One Reset button
• Power: PoE 802.3af; 12VDC external power in connector (see
• Antennas:
– Eight RP-SMA external antennas
– One RP-SMA BLE antenna
– One BLE internal antenna
•Temperature:
– -20 to +50°C ambient temperature anywhere
• Enclosure: Plastic with metal base
Figure 1 Top and Side Views of AP510e
1
USB Port
Table 1 AP 51 0 e Pow e r i n g M e t h ods
Power Source Description
Redundant power is provided through the RJ45
Ethernet ports (LAN ports,
Power over Ethernet (PoE)
External 12V DC power supply
(optional; ordering part
#37219 - PWR 12VDC,
3A, 2.5mm x 5.5mm
connector)
of AP510e, compliant to be powered with 802.3af and
provide full functionality with 802.3at. This is the
preferred method of powering the AP on ceiling and
high wall installations.
The AP510e can also be powered by an external DC
power supply plugged into an AC source. Plug the
supply’s input jack into the 12V DC (
port.
Note: PoE is disabled when external power supply is used.
Figure 2 AP510e back ports
Ta bl e 1 for details)
Figure 2, items #4 and #5)
Figure 2, item #2)
Table 2 Description of back ports of AP510e
Number Description
1
Kensington lock
2
12V DC power supply
3
Console port (Yellow)
4
LAN 2 (GE) (Black)
5
LAN 1 (5 GE) (Purple)
LEDs Status
The LEDs are located on the front face of the AP but are not visibly marked.
Table 3 AP 5 1 0 e L E D S t a t u s
LED Icon LED Color Description
Status GREEN Normal operational status
AMBER Non-operational status
GE1 Ethernet AMBER 100 Mbps
GREEN 1000 Mbps
PURPLE 2.5G/5G
GE2 Ethernet AMBER 100 Mbps
GREEN 1000 Mbps
Radio #1 Status GREEN 2.4GHz
AMBER 5GHz
WHITE Sensor
Radio #2 Status AMBER 5GHz
IoT (BLE) BLUE Indicates BLE is enabled
OFF Non-operational status
For detailed installation information about the AP510e, see the ExtremeWireless AP510e
Installation Guide.
Verifying the AP510e Box Contents
Verify the contents of the box and ensure that the following items are available:
Table 4 Contents of the AP510e Box
Quantity Item
1AP510e Quick Reference Guide
1 Mounting bracket for 802.11ax indoor access point
1 Cloud Quick Start Card
1 AP510e access point
2 Phillips pan-head wood screws
2 Screw-in anchors
Mounting and Connecting the AP
Electrical Hazard: Only qualified personnel should perform installation
procedures.
Use these instructions as guidelines for mounting and connecting the AP510e easily and
safely.
The AP510e comes with a Mounting Bracket (#37201) that can be used to mount the AP
on a flat t-bar with flat ceiling tiles, flat surfaces, beams, and some junction/gang boxes.
An adaptor and brackets are available for mounting the AP to non-flat ceiling tiles and tbars. To mount the AP510e on a junction/gang box, use the optional bracket (WS-MBIWALL04; #30516). All additional and optional parts are sold separately.
Note: The mounting procedures for installing the AP using the WS-MBIDCFLUSH (ordering part #37211) adaptor to a T-bar, WS-MBI-DCMTR01
(ordering part #30518) to a T-bar, and using the main mounting bracket
(ordering part #37201) along with a flat metal-easy attach adaptor (ordering
part #37210), Accessory BRKT-000147A-01 (beam clip), and KT-135628-01 are
covered in the ExtremeWireless AP510e Installation Guide.
Mounting the AP on a Wood Wall/Solid Flat Ceiling
Pre-installation checklist:
• The mounting surface, item, and hardware must be able to support the AP in all
environmental conditions.
• The mounting surface should be flat.
To install the AP on a dry wall or flat surface:
Option 1: Using the Main Mounting Bracket
1 Use the mounting bracket as a template and mark the hole centers on the wall.
Note: The four feet of the bracket and the direction of the arrow mark must be
vertical and pointing up and the flat part of the bracket must be touching the
surface it is being attached to.
2 Drill two holes 83mm (3.270”) apart from each other on the wall where you want to
mount the AP.
3 Insert the screws into the holes of the mounting bracket and use the screw-in anchors
if needed.
4 Insert the Ethernet cable’s RJ45 connector into the LAN1/GE1 port.
5 Insert the AP onto the bracket’s four feet and slide it down to lock it in place.
Note: The T-bar width can be either 9/16” (15mm) or 15/16” (24mm).
Option 2: Using an optional Wall and Box bracket
For detailed instructions, see the ExtremeWireless AP510e Installation Guide.
Mounting the AP to a Suspended or Drop Ceiling
The AP510e can be mounted to a suspended or drop ceiling directly using the mounting
bracket on the t-bar. If there is a ceiling tile protrusion, add the optional T-bar adaptor to
the main mounting bracket prior to T-bar installation.
Option 1: Using the Main Mounting Bracket to a T-bar
Before installation ensure that:
• The base thickness of the T-bar that supports the ceiling tile is 0.031”.
• The maximum base thickness of the T-bar of the T-bar is 0.055”.
Note: The T-bar width can be either 9/16” (15mm) or 15/16” (24mm).
1 Remove the ceiling tiles, slide and rotate the main mounting bracket onto the T-bar in
such a way that the center angled locking tabs of the main bracket gets attached to
the T-bar.
2 Replace the tiles to hold the T-bar in place.
3 Hold the AP and rock it back and forth to ensure it is securely mounted.
4 Attach the Ethernet cable’s RJ45 connector to the LAN1/GE1 port.
Option 2: Mounting the AP by attaching an adaptor to the main bracket
For detailed instructions, see the ExtremeWireless AP510e Installation Guide.
Mounting the AP on a Junction or Gang Box
For detailed procedure on Installing the AP to a Junction or Gang Box, see the
ExtremeWireless AP510e Installation Guide.
Mounting the AP to a Beam
For detailed procedure on Installing the AP to a Beam, see the ExtremeWireless AP510e
Installation Guide.
Connecting a Power Supply to the AP510e
If you need to power the AP510e with an external 12V DC power supply, you can plug the
power cord into the power connector on the back of the AP. There is no wall mount
bracket for the 12V DC power supply. When the device is powered on, the power LED on
the front face of the AP is lit. Refer to the ExtremeWireless AP510e Installation Guide for
information about optional power supplies.
Antenna Configurations for External Antenna
Models
Figure 3 AP510e External RP-SMA Antenna Connectors
Table 5 AP510e Antenna Configuration
Software
Mode
Mode 1 2.4 GHz 5 GHz Dual Band 2.4/5 GHz None
Mode 2 Band Unlocked
Mode 3 5 GHz 5 GHz 5 GHz 5 GHz
Radio 1 Radio 2 Antenna Ports
2.4G/5G - 1,2,3,4 5G- 5,6,7,8
Sensor
5 GHz Dual Band 2.4/5 GHz 5 GHz
Operational Description of Antenna
Configuration and RF Output Power Setting
Per KDB 353028 D01 Antennas Part 15 Transmitters v01 requirement, Applications must
contain an exhibit listing each antenna, the antenna gain, antenna type, and antenna
manufacturer/vendor and output power that can be used for the device, that the info
listed below are correct and represent the product in consideration under this filing.
Professional Installation Instruction
Installation personal
This product is designed for specific application and needs to be installed by a qualified
personal who has RF and related rule knowledge. The general user shall not attempt to
install or change the setting.
Installation location
The product shall be installed at a location where the radiating antenna can be kept 36
cm from nearby person in normal operation condition to meet regulatory RF exposure
requirement.
External antenna
Use only the antennas which have been approved by the applicant. The non-approved
antenna(s) may produce unwanted spurious or excessive RF transmitting power which
may lead to the violation of FCC/IC limit and is prohibited.
Installation procedure
Please refer to user’s manual for the detail.
Warni ng : Please carefully select the installation position and make sure that
the final output power does not exceed the limit set force in relevant rules. The
violation of the rule could lead to serious federal penalty.
Instructions d'installation professionnelle
Installation
Ce produit est destine a un usage specifique et doit etre installe par un personnel qualifie
maitrisant les radiofrequences et les regles s'y rapportant. L'installation et les reglages ne
doivent pas etre modifies par l'utilisateur final.
Emplacement d'installation
En usage normal, afin de respecter les exigences reglementaires concernant l'exposition
aux radiofrequences, ce produit doit etre installe de facon a respecter une distance de 36
cm entre l'antenne emettrice et les personnes.
Antenn externe
Utiliser uniiquement les antennes approuvees par le fabricant. L'utilisation d'autres
antennes peut conduire a un niveau de rayonnement essentiel ou non essentiel
depassant les niveaux limites definis par FCC/IC, ce qui est interdit.
Procedure d'installation
Warni ng : Avertissement: Choisir avec soin la position d'installation et
s'assurer que la puissance de sortie ne depasse pas les limites en vigueur. La
violation de cette regle peut conduire a de serieuses penalites federales.
Consulter le manuel d'utilisation.
Regulatory and Compliance Information
This section contains notices that are intended to protect your personal safety and
prevent damage to the equipment.
Qualified Personnel:
Electrical Hazard: Only qualified personnel should perform installation
procedures. Within the context of the safety notes in this documentation,
qualified persons are defined as persons who are authorized to commission,
ground and label devices, systems, and circuits in accordance with established
safety practices and standards. A qualified person understands the
requirements and risks involved with installing outdoor electrical equipment in
accordance with national codes.
Federal Communications Commission (FCC) Notice
This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This
equipment generates, uses and can radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by one of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
Caution: Any changes or modifications not expressly approved by the party
responsible for compliance could void the user's authority to operate this
equipment.
Safety Guidelines
This device complies with Part 15 of the FCC Rules. Operation is subject to the following
two conditions: (1) This device may not cause harmful interference, and (2) this device
must accept any interference received, including interference that may cause undesired
operation.
This transmitter must not be co-located or operating in conjunction with any other
antenna or transmitter.
Operations in the 5.15-5.25GHz band are restricted to indoor usage only.
FCC Radiation Exposure Statement: This equipment complies with FCC
radiation exposure limits set forth for an uncontrolled environment. This
equipment should be installed and operated with minimum distance 20cm
between the antenna & your body.
Note: This module is intended for OEM integrator. The OEM integrator is
responsible for the compliance to all the rules that apply to the product into
which this certified RF module is integrated. Additional testing and certification
may be necessary when multiple modules are used.
Industry Canada Notice
This device complies with ISED’s licence-exempt RSSs. Operation is subject to the
following two conditions: (1) This device may not cause harmful interference, and (2) this
device must accept any interference received, including interference that may cause
undesired operation.
Le présent appareil est conforme aux CNR d’ ISED applicables aux appareils radio
exempts de licence. L’exploitation est autorisée aux deux conditions suivantes : (1) le
dispositif ne doit pas produire de brouillage préjudiciable, et (2) ce dispositif doit
accepter tout brouillage reçu, y compris un brouillage susceptible de provoquer un
fonctionnement indésirable.
Caution: The device for operation in the band 5150-5250 MHz is only for
indoor use to reduce the potential for harmful interference to co-channel
mobile satellite systems.
Caution: Avertissement: les dispositifs fonctionnant dans la bande 5150-
5250 MHz sont réservés uniquement pour une utilisation à l’intérieur afin de
réduire les risques de brouillage préjudiciable aux systèmes de satellites
mobiles utilisant les mêmes canaux.
War nin g: IC Radiation Exposure Statement: This equipment complies with
IC radio-frequency exposure guidelines set forth for an uncontrolled
environment. This equipment should be installed and operated with minimum
distance 20cm between the antenna & your body.
War nin g: Déclaration d'exposition aux radiations: Cet équipement est
conforme aux limites d'exposition aux rayonnements IC établies pour un
environnement non contrôlé. Cet équipement doit être installé et utilisé avec
un minimum de 20 cm de distance entre la source de rayonnement et votre
corps.
Detachable Antenna Usage
This radio transmitter [4141B-AP510E] has been approved by Innovation, Science and
Economic Development Canada to operate with the antenna types listed below, with the
maximum permissible gain indicated. Antenna types not included in this list that have a
gain greater than the maximum gain indicated for any type listed are strictly prohibited
for use with this device.
Le présent émetteur radio [4141B-AP510E] a été approuvé par Innovation, Sciences et
Développement économique Canada pour fonctionner avec les types d'antenne
énumérés ci-dessous et ayant un gain admissible maximal d'antenne. Les types
d'antennes non inclus dans cette liste qui ont un gain supérieur au gain maximal indiqué
pour tout type listé sont strictement interdits pour une utilisation avec cet appareil.
Approved Antenna(s) list:
This device and its antenna(s) must not be co-located with any other transmitters except
in accordance with IC multi-transmitter product procedures. Referring to the multitransmitter policy, multiple-transmitter(s) and module(s) can be operated
simultaneously without reassessment permissive change.
Cet appareil et son antenne (s) ne doit pas être co-localisés ou fonctionnement en
association avec une autre antenne ou transmetteur.
Note: This module is intended for OEM integrator. The OEM integrator is
responsible for the compliance to all the rules that apply to the product into
which this certified RF module is integrated. Additional testing and certification
may be necessary when multiple modules are used.
Other Countries
Brazil
Este produto está homologado pela ANATEL, de acordo com os procedimentos
regulamentados pela Resolução n°. 242/2000 e atende aos requisitos técnicos
aplicados.
Este equipamento não tem direito à proteção contra interferência prejudicial e não pode
causar interferência em sistemas devidamente autorizados. Para maiores informações,
consulte o site da ANATEL – www.anatel.gov.br
MPE Statement - Mobile Device
This equipment complies with EU radiation exposure limits set forth for an uncontrolled
environment. This equipment should be installed and operated with minimum distance
20cm between the radiator & your body.
CE Statement
The device is restricted to indoor use only when operating in the
5150 to 5350 MHz frequency range.
AT BE BG HR CY CZ DK
EE FI FR DE EL HU IE
IT LV LT LU MT NL PL
PT RO SK SI ES SE UK
All Operational Modes
2.4GHz: 802.11b, 802.11g, 802.11n (HT20), 802.11n (HT40), 802.11ac (VHT20), 802.11ac
(VHT40), Bluetooth(BR/EDR, LE)
5GHz: 802.11a, 802.11n (HT20), 802.11n (HT40), 802.11ac (VHT20), 802.11ac (VHT40),
802.11ac (VHT80), 802.11ac (VHT160)
The frequency and the maximum transmitted power in EU are listed below:
2412-2472MHz: 20 dBm
2402-2480MHz (BR/EDR): 6 dBm
2402-2480MHz (LE): 8 dBm
5180-5240MHz: 23 dBm
5260-5320MHz: 23 dBm
5500-5700MHz: 30 dBm
European Waste Electrical and Electronic Equipment
(WEEE) Notice
In accordance with Directive 2012/19/EU of the European Parliament on waste electrical
and electronic equipment (WEEE):
1 The symbol above indicates that separate collection of electrical and electronic
equipment is required.
2 When this product has reached the end of its serviceable life, it cannot be disposed of
as unsorted municipal waste. It must be collected and treated separately.
3 It has been determined by the European Parliament that there are potential negative
effects on the environment and human health as a result of the presence of hazardous
substances in electrical and electronic equipment.
4 It is the users’ responsibility to utilize the available collection system to ensure WEEE
is properly treated.
For information about the available collection system, please contact Extreme
Environmental Compliance at Green@extremenetworks.com.
Hazardous Substances
This product complies with the requirements of Directive 2011/65/EU of the European
Parliament and of the Council of 8 June 2011 on the restriction of the use of certain
hazardous substances in electrical and electronic equipment.
Declaration of Conformity in Languages of the European
Community
English Hereby, Extreme Networks, declares that the radio equipment type
Finnish Valmistaja Extreme Networks vakuuttaa täten että Radio LAN device
Dutch Hierbij verklaart Extreme Networks dat het toestel Radio LAN device
French Par la présente Extreme Networks déclare que l'appareil Radio LAN
Swedish Härmed intygar Extreme Networks att denna Radio LAN device står I
Danish Undertegnede Extreme Networks erklærer herved, at følgende udstyr
German Hiermit erklärt Extreme Networks die Übereinstimmung des "WLAN
Greek ΜΕ ΤΗΝ ΠΑΡΟΥΣΑ Extreme Networks ∆ΗΛΩΝΕΙ ΟΤΙ Radio LAN
Icelandic Extreme Networks lysir her med yfir að thessi bunadur, Radio LAN
Italian Con la presente Extreme Networks dichiara che questo Radio LAN
Spanish Por medio de la presente Extreme Networks declara que el Radio LAN
Portuguese Extreme Networks declara que este Radio LAN device está conforme
Malti Hawnhekk, Extreme Networks, jiddikjara li dan Radio LAN device
[AP510e] is in compliance with Directive 2014/53/EU. For full text of
the EU Deceleration of Conformity, please contact Extreme
Regulatory Compliance at compliancerequest@extremenetworks.com
tyyppinen laite on direktiivin 2014/53/EU oleellisten vaatimusten ja
sitä koskevien direktiivin muiden ehtojen mukainen.
in overeenstemming is met de essentiële eisen en de andere relevante
bepalingen van richtlijn 2014/53/EU.
device est conforme aux exigences essentielles et aux autres
dispositions pertinentes de la directive 2014/53/EU.
överensstämmelse med de väsentliga egenskapskrav och övriga
relevanta bestämmelser som framgår av direktiv 2014/53/EU.
Radio LAN device overholder de væsentlige krav og øvrige relevante
krav i direktiv 2014/53/EU.
Wireless Controller bzw. Access Points" mit den grundlegenden
Anforderungen und den anderen relevanten Festlegungen der
Richtlinie 2014/53/EU.
device ΣΥΜΜΟΡΦΩΝΕΤΑΙ ΠΡΟΣ ΤΙΣ ΟΥΣΙΩ∆Ε ΙΣ ΑΠΑΙΤΗΣΕΙΣ
ΚΑΙ ΤΙΣ ΛΟΙΠΕΣ ΣΧΕΤΙΚΕΣ ∆ΙΑΤΑΞΕΙΣ ΤΗΣ Ο∆ΗΓΙΑΣ 2014/53/
EU.
device, uppfyllir allar grunnkrofur, sem gerdar eru i R&TTE tilskipun
ESB nr 2014/53/EU.
device è conforme ai requisiti essenziali ed alle altre disposizioni
pertinenti stabilite dalla direttiva 2014/53/EU.
device cumple con los requisitos esenciales y cualesquiera otras
disposiciones aplicables o exigibles de la Directiva 2014/53/EU.
com os requisitos essenciais e outras disposições da Directiva 2014/
53/EU.
jikkonforma mal-htigijiet essenzjali u ma provvedimenti ohrajn
relevanti li hemm fid-Dirrettiva 2014/53/EU.
ExtremeMobilityTM
Access Points
Quick Reference
AP510e-FCC
AP510e-WR
AP510e-FCC-TAA
Notice
Copyright © 2019 Extreme Networks, Inc. All Rights Reserved.
Legal Notices
Extreme Networks, Inc. reserves the right to make changes in specifications
and other information contained in this document and its website without
prior notice. The reader should in all cases consult representatives of Extreme
Networks to determine whether any such changes have been made.
The hardware, firmware, software or any specifications described or referred
to in this document are subject to change without notice.
Trademarks
Extreme Networks and the Extreme Networks logo are trademarks or
registered trademarks of Extreme Networks, Inc. in the United States and/or
other countries.
All other names (including any product names) mentioned in this document
are the property of their respective owners and may be trademarks or
registered trademarks of their respective companies/owners.
For additional information on Extreme Networks trademarks, please see:
www.extremenetworks.com/company/legal/trademarks/
Documentation, Installation Videos, & Support
For product support, including Documentation and Installation Videos, visit:
www.extremenetworks.com/documentation
P/N 9035995-03
Loading...