Extreme Networks AP3825E User Manual

802.11 a/n/ac Module

QXO-AP3825E

User’s Manual

- 1 -

PRODUCT DESCRIPTION

The QXO-AP3825E is a 5G dual band concurrent 3T3R PCIe module
base on QCA9890 solution.

PRODUCT SPECIFICATION

RF Specification

Radio 1
Interface
Operating Voltage
Antenna Conne ct o rs
Frequency Band

Data rate 1300Mbps

Receive

Sensitivity (Typical) 802.11a ≤ -94dBm@6Mbps

Support 5GHz
64-bit PCI-E

3.3V
I-PEX

802.11a/n/ac

5.190~5.795GHz

802.11a/ n_HT20 ≤ -93dBm @ MCS0/8/16

802.11n_HT40 ≤ -92dBm @ MCS0/8/16

802.11ac_HT80 ≤ -89dBm@MCS0
≤ -64dBm@MCS9

PRODUCT Pin Define

≤ -76dBm@54Mbps

≤ -74dBm @ MCS7/15/23

≤ -72dBm @ MCS7/15/23

- 2 -

List of certificated antennas

PIFA

6

PIFA

Dipole

3

Panel

Panel

6

Omni

2

Sector

5

Type Model Connector 5150~5250MHz 5725~5850MHz

NA

ANT-PIFA7262AG

WS-ANT-5DIP-3
WS-AI-DX07025
WS-AI-DX10055

WS-AI-DX02360

WS-AI-DT05120

U.FL
U.FL

5.5

RPSMA
RPSMA

5.5

RPSMA 6
RPSMA 2
RPSMA 5

6

5.5

3

5.5

Note: The EUT has three antennas. (3TX/3RX )

Any changes or modifications not expressly approved by the manufacturer could void the user's
authority to operate this equipment.

USERS MANUAL OF THE END PRODUCT:
In the users manual of the end product, the end user has to be informed to keep at least 20cm separation
with the antenna while this end product is installed and operated. The end user has to be informed that
the IC radio-frequency exposure guidelines for an uncontrolled environment can be satisfied. The e nd
user has to also be informed that any changes or modifications not expressly approved by the
manufacturer could void the user's authority to operate this equipment. IC statement is re quired to be
available in the users manual: This Class B digital apparatus complies with Canadian ICES-003.
Operation is subject to the following two conditions: (1) this device may not cause harmful interference
and (2) this device must accept any interference received, including interference that may cause
undesired operation.

- 3 -

Federal Communication Commission Interference Statement

This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment generates, uses and can radiate
radio frequency energy and, if not installed and used in accordance with the instructions, may cause
harmful interference to radio communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and on, the user is encouraged to try to
correct the interference by one of the following measures:

- Reorient or relocate the receiving antenna.

- Increase the separation between the equipment and receiver.

- Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.

- Consult the dealer or an experienced radio/TV technician for help.

FCC Caution: Any changes or modifications not expressly approved by the party responsible for
compliance could void the user's authority to operate this equipment.

IMPORTANT NOTE:
FCC Radiation Exposure Statement:

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment.
This equipment should be installed and operated with minimum distance 20cm between the radiator &
your body.
This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.

Operations in the 5.15-5.25GHz / 5.470 ~ 5.725GHz band are restricted to indoor usage only.
The band from 5600-5650MHz will be disabled by the software during the manufacturing and cannot be
changed by the end user.
This device meets all the other requirements specified in Part 15E, Section 15.407 of the FCC Rules.

4 -

-