ETC UFMP4 Datasheet

®

Unison Foundry® Mini PanelsETC

Foundry Mini Panel Series

GENERAL INFORMATION

The Foundry Mini Panels offer up to eight zones of DMX controlled
lighting with fully rated 20 Amp relays and optional 0-10V control
per zone. The Mini Panel features a Demand Response input for
energy saving integration and a UL924 emergency lighting control
bypass with power loss sense. The Mini Panel is wall-mounted and
plenum rated to be easily tucked out of sight.

APPLICATIONS

• Arena and stadium suites

• Office buildings

• Conference and meeting rooms

• Healthcare facilities

• Houses of worship

• Classrooms

• Hospitality and restaurants

• Retail

FEATURES

• Switched power control of four or eight circuits with 0-10V
dimming

• 120 or 277VAC power input per zone

• 20 Amp fully rated relays for use with general purpose,
tungsten, fluorescent, LED and plug loads

• 0-10V dimming output per zone for direct connection to
dimming ballasts and LED drivers

• Demand Response load shedding contact input

• UL924 control bypass via

- Contact closure input

- Normal power loss sense feed terminals

• DMX controlled and RDM configurable

GENERAL

• UL, cUL and UL924 LISTED

• Rated for plenum installation

• Suitable for plug load control

ORDERING INFORMATION

Foundry Mini Panel

MODEL DESCRIPTION

UFMP4 4-zone DMX Mini Panel with four relays and four

0-10V dimming outputs

UFMP8 8-zone DMX Mini Panel with eight relays and

eight 0-10V dimming outputs

Note: Optional voltage divider available for use of mixed normal and
emergency circuits in a single controller; where allowed by local code.

FOUNDRY FAMILY OF PRODUCTS

Foundry Distributed Product Series

MODEL DESCRIPTION

UFR2 Dual Zone DMX Relay

UFR2-LV Dual Zone DMX Relay with 0-10V

UFD 600W 120V DMX Dimmer

UFD-277 600W 277V DMX Dimmer

Foundry Mini Panel Product Series

MODEL DESCRIPTION

UFMP4 4 Zone Mini Panel

UFMP8 8 Zone Mini Panel

1 of 3

Unison Foundry Mini PanelsETC

Foundry Mini Panel Series

SPECIFICATIONS

FUNCTIONAL

• Control for up to eight zones of switching for lighting and plug loads

• Control for up to eight zones of 0-10V dimming for LED drivers and fluorescent ballasts

• UL924 emergency-lighting control via contact closure and power loss sense feed terminal

• Demand Response input provided by a power company can enforce a maximum level per circuit while active

• Supports USITT DMX512-A (ANSI E1.11)

• Supports RDM (ANSI E1.20)

MECHANICAL

• Constructed of 16-gauge cold-rolled steel, finished in fine-textured, black powder coat

• Wall-mount installation;

- rated for installation in plenum air space

• Class-1 voltage barrier prevents access to line-voltage wiring with front panel removed

• Optional voltage divider allows for separation of normal and emergency circuits in a single controller where allowed by local codes

ELECTRICAL

• 100-277V, 50/60Hz power input per circuit with support for pass thou to multiple circuits

• Supports 120V and 277V circuits within the same panel

• 20-Amp, fully-rated bi-state latching relay per output

• 0-10VDC control rated for up to 100mA sink per output

- 0-10V outputs are fully isolated from ground to 2500V RMS

• Rising clamp screw terminal wiring connections for:

- Line-voltage relay power input, output and pass-through with support for 14-8 AWG wire

- Low-voltage 0-10V dimming output per zone with support for 22-16 AWG wire

- Separate normal power sense feed input for UL924 emergency lighting bypass

- UL924 emergency lighting control contact closure input with support for 22-16 AWG wire

- Demand Response contact input with support for 22-16 AWG wire

• Demand Response input supports Normally Open (NO) operation

• UL924 contact closure input supports normally open (NO) or normally closed (NC) operation

• Onboard status indicators for controller power, DMX signal, Demand Response input, and UL924 emergency lighting control

• Slide switch configuration for:

- UL924 operation (NO/NC)

- UL924 inclusion per circuit (on/off)

• UL and cUL LISTED

- Conforms to UL508, UL2043, UL916 and UL924

DMX INPUT PORT

• Optically-isolated input from the Mini Panel electronics

• Withstands fault voltages of up to 250VAC

• Integrated DMX/RDM termination

CONFIGURATION

• Remote configuration available via RDM devices such as:

- ETC control console with RDM functionality

- ETC DMX/RDM gateway networked to a device running ETC Net3 Concert software

• Manual configuration of the starting DMX address, UL924 bypass, and Demand Response on the controller

THERMAL

• Ambient room temperature: 0 to 50°C

• Ambient humidity: 5 to 95% non-condensing

2 of 3

PHYSICAL

12.00”

0.06”

3.00”

10.00”

12.00”

0.06”

3.00”

10.00”

Unison Foundry Mini PanelsETC

Foundry Mini Panel Series

Foundry Mini Panel Dimensions

MODEL HEIGHT WIDTH DEPTH

inches mm inches mm inches mm

UFMP4 9.0 229 12 301 3 76

UFMP8 14.0 356 12 301 3 76

301mm

9.00”

229mm

1.7mm

Foundry Mini Panel Weights

MODEL WEIGHT

lbs kgs

UFMP4 6 2.72

UFMP8 9 4.08

UFMP4

76mm

7.00”

178mm

MOUNTING
REFERENCE

254mm

MOUNTING REFERENCE

301mm

UFMP8

1.7mm

14.00”

356mm

Corporate Headquarters n 3031 Pleasant View Rd, PO Box 620979, Middleton WI 53562 0979 USA n [phone]
London, UK n Unit 26-28, Victoria Industrial Estate, Victoria Road, London W3 6UU, UK n [phone]
Rome, IT n Via Pieve Torina, 48, 00156 Rome, Italy n [phone]
Holzkirchen, DE n Ohmstrasse 3, 83607 Holzkirchen, Germany n [phone]
Hong Kong n Room 1801, 18/F, Tower 1 Phase 1, Enterprise Square, 9 Sheung Yuet Road, Kowloon Bay, Kowloon, Hong Kong n [phone]
Web n etcconnect.com n Copyright©2018 ETC. All Rights Reserved. All product information and specifications subject to change. 7179L1001 Rev A 01/18

3 of 3

76mm

12.00”

301mm

MOUNTING
REFERENCE

254mm

MOUNTING REFERENCE