Esotec Satin Glass User guide

Operating Manual

GB

LED Solar Lamp „Satin Glass“

These instructions relate ONLY to this product and contain important information
for using the product for the first time. Please keep these instructions for later
reference and should always accompany the product in the event of transference
to a new user.

4.

5.

6.

1. Introduction

Dear Costumer,
Thank you for purchasing the solar light.
With this solar light you purchased a product manufactured according to the
current state of technology.

facturer.

To maintain this state and guarantee a safe operation, you as the user will have
to follow this operating manual!

This product fulfils all requirements of the valid European and
national regulations. The conformity was proved. The relevant
declarations and documentation are deposited with the manu-

2. Safety Instructions

- In case of damages caused by not following this
operating manual, the warranty rights will expire!

We exclude liability for any consequential damages!

- We exclude liability for property or personal

!

damages caused by inappropriate handling

or not following the safety instructions.

- In these cases any guarantee rights will expire.

Due to safety and admission reasons (CE) it is not allowed to arbitrarily recon­struct and/or change the solar light.
Therefore, please keep to the operating manual.
The accident prevention rules of the association of the industrial trade coope­rative association for electric plants and working material are to be considered
in industrial environments

3. Intended use

The solar lamp is designed for outdoor use. The integrated rechargeable
battery is charged via the solar cell in the lid of the lamp. The lamp is
automatically switched on at darkness and switched out at the break of dawn.
2 powerful white light emitting diodes (LEDs) are used as light source. Those
LEDs ensure a high luminosity with low power consumption. The light color

may be switched between a yellow ickering light (imitation of a candle) and a

7-color alternating light. This is done via a switch.

-- However, please note that the duration of illumination may be impaired
in case of insufcient solar irradiation onto the solar module or during the
winter months --

Note: In case of longer periods without solar irradiation, the accumulator won’t
be charged sufciently in order to ensure a permanent operational readiness.

But that doesn’t mean that the solar light is defective. Wait for the next
sunny days and the light will again work accordingly or charge the batteries in a
commercially available battery charger.

4. Putting into operation

1. Please carefully take all parts out of the package.

2. For safety sake, hold one hand onto the lid. This will avoid any damages
of the lid when opening the jar. Now open the clasp of the lid by pulling the
clamp forward (ill. 1).

3. Remove the clamp and open the lid of the canning jar (ill. 2).

4. Inside the lid you will nd a slide switch. The lamp is switched off in the

center position „OFF“. The yellow ickering light is activated in position
„ON2“ and the 7-color alternating light is activated in position „ON1“ (ill. 3).

5. Then close the lid and rmly press it onto the gasket. Now close the canning

jar with the clasp.

Attention: Do not apply force when opening and closing the lamp. Danger of
injury due to genuine glass!

The solar lamp is now activated.

Note: The duration of illumination is strongly dependent of the intensity and
duration of sunshine during the day. During the winter months, the duration of
illumination will generally be shorter. In case the light should not give light on the

rst evening, please wait for a sunny day.

1.

2.

3.

5. Exchange of the rechargeable battery

1. For safety sake, hold one hand onto the lid (ill. 4). This will avoid any
damages of the lid when opening the jar. Now open the clasp of the lid by
pulling the clamp forward.

2. Remove the clamp and open the lid of the canning jar.

3. Put the slide switch into the center position.

4. Turn the reector anticlockwise and remove it carefully.

5. Unscrew the 3 screws with an appropriate screwdriver and carefully remove
the cover (ill. 5).

6. Take the used rechargeable battery out of the battery compartment and insert
a new accumulator with correct polarity (ill. 6). We recommend charging the
new accumulator in a charger before inserting it.

7. Now, re-assemble and close the lamp in reverse order.

Note: Used batteries or accumulators must be disposed of in a non-polluting
way and do not belong into the domestic waste. Your dealer is required by law
to take back old accumulators.

6. Malfunctions

-Lamp is not automatically switched on at darkness

• An outside light source (e.g. streetlight) simulates daylight and prevents the

lamp from switching on. Place the lamp at a darker location.

Lamp is not switched on at darkness or only for a short period of time.

• Is the lamp connected?

• Accumulator weak or defective. Exchange of the accumulators.

7. Technical Data

• Solar module: 2 V/ 80 mA

• LED: 1 xyellow LED and 1 x RGB LED

• Degree of protection: IP 44

• Protection class: III

• Battery: 1x NiMh 1.2 V/600 mAh (Micro AA)

• Luminosity period: Max. 6 hrs with full battery

• Working temperature: -20°C bis + 40°C

Battery Recycling:

• Used batteries or accumulators must be disposed in the
domestic waste.

• The consumer is legally obliged to bring back old accumu­lators upon usage, e.g. to public waste collecting locations
or to the place (shops, etc.) where those batteries are sold.

• Batteries that contain harmful substances are marked
with the “strike through dustbin” and one of the chemical
symbols.

Manufacturer - Spare parts
esotec GmbH - Weberschlag 9 - D-92729 Weiherhammer

Tel.-Nr: [phone] Fax.-Nr: [phone]
e-mail:[e-mail] Internet: www.esotec.de

Manufacturer Part- Nr: 102078

Rechargeable battery notes

- Rechargeable batteries should not be played with by children. Never leave rechar­geable batteries lying around; they could be swallowed by children or pets.

- Rechargeable batteries must never be short-circuited, disassembled or thrown into
fire. This leads to a danger of explosion!

- Leaking or damaged rechargeable batteries can cause chemical burns when they
come into contact with skin. For this reason, please make use of suitable protective
gloves.

- Rechargeable batteries should only be replaced by structurally identical rechar­geable batteries from the same manufacturer. Normal batteries must not be used
since these are not rechargeable.

- Make sure the rechargeable batteries are inserted with the correct polarity.

- For long periods of time of non-use (for example, storage), remove the inserted
rechargeable batteries to avoid damages via the leaking rechargeable batteries.

Disposal:

Dear customer,
please cooperate in avoiding waste. When you intend to dispose of the
product in future, please consider that it contains valuable raw materials
suited for recycling.
Therefore, do not dispose it of with domestic waste but bring it to a collec­tion point for the recycling of waste electrical and electronic equipment.
Thank you very much for your cooperat

ion!

NiMh

Copyright, esotec GmbH