Esotec Profi 2 Operating Manual

Using Instructions -Profi 2

These instructions relate ONLY to this product and contain important
information for using the product for the first time. Please keep these
instructions for later reference and should always accompany the
product in the event of transference to a new user.

GB

1. Introduction

Dear Costumer,
Thank you for purchasing the solar light. With this solar light you purcha­sed a product manufactured according to the current state of technology.

This product fulfils all requirements of the valid European and natio­nal regulations. The conformity was proved. The relevant declarati­ons and documentation are deposited with the manufacturer.

To maintain this state and guarantee a safe operation, you as the user will
have to follow this operating manual!

2. Safety Instructions

- In case of damages caused by not
following this operating manual, the
warranty rights will expire! We exclude
liability for any consequential damages!

!

- In these cases any guarantee rights will expire.

Due to safety and admission reasons (CE) it is not allowed to arbitrarily
reconstruct and/or change the solar light.
Therefore, please keep to the operating manual.
The accident prevention rules of the association of the industrial trade
cooperative association for electric plants and working material are to be
considered in industrial environments.

- We exclude liability for property or
personal damages caused by inappropriate
handling or not following the safety instructions.

3. Usage in Accordance with Requirements

The illumination may be mounted individually by on top of existing signs.
The professional sign illumination is available in three different lengths
and may thus be used for different sign lengths.
The illumination is automatically activated at darkness and deactivated at
morning light. The maximum illumination duration with a full accumulator
and without recharging is approximately 25 hours. The solar module
installed in the upper part of the housing charges the integrated accumu­lator.
Note: Please make sure that the solar module is preferably directed to
the South, the East or the West and that shadows are avoided. When
directing the module to the North it is not possible to use the product. The

solar module shall always be free of snow in the winter.

5.

6.

6.

5. Exchanging the accumulator pack

After one to two years, the capacity of the accumulator packs will decrea­se. It is then required to exchange all accumulator packs. The accumula­tor packs are available in the shops or from the manufacturer. It is only
allowed to use an identical accumulator pack with the same electrical
values (at least 1300 mAh).

1. Open the housings as described above and extract the plug of the
accumulator packs from the circuit board (point 4).

2. Open the accumulator housing by pressing the two lateral locks (point 5).

3. Remove all accumulator packs from the housing, insert the new accu­mulator packs and close the lid of the battery compartment (point 6).

4. Re-insert the plug of the accumulator packs into the bush on the elec­tronics (point 4).

5. Close the housing in reverse order.

Note: Used batteries or accumulators must be disposed of in a non-pol­luting way and do not belong into the domestic waste. Your dealer is
legally obliged to take back and recycle old accumulators.

6. Malfunctions

- Lamp is not automatically switched on at darkness

- An outside light source (e.g. streetlight) simulates daylight and pre­vents the lamp from switching on. Place the lamp at a darker location.

- Lamp is not switched on at darkness or only for a short period of
time.

- Is the lamp connected?

- Accumulator weak or defective. Exchange of the accumulators.

7. Specifications Profi 1 Profi 2 Profi 3

Operating voltage: 3,6 V 7,2 V 14,4 V
Battery: (NiMh 3,6 V/ 1300 mAh): 1 pc. 2 pcs. 4 pcs.
Illuminating units: 2 pcs. 4 pcs. 8 pcs.
Illumination time with a full battery: 25 h 25 h 25 h

spare battery-pack:

NiMh 3,6 V/ 1300 mAh: part no.: 901021 (www.esotec.eu)
It is required to exchange all accumulator packs and to only use identical
accumulator packs with the same electrical values (at least 1300 mAh).

open

press

4. Initiation

1. Please carefully take all
parts out of the package and
check the illumination for
transport damages.
Press the steel plate with the

2.
illuminating diodes, open the
lid with the solar module and
take it off.

3. Extract the plug for the solar module from the circuit (point 3).
Install the back part of the sign illumination with the LEDs directed to

4.
the bottom on top of the sign to be illuminated. Use the enclosed
screws and plugs for the installation.

5. Now insert the bush of the accumulator pack (accumulator pack is
situated in the white housing) into the plug on the circuit board (point 4).
Note: The plug is reverse-polarity protected. Please do not apply
force when inserting the plug.

6. Now re-insert the bush of the solar module onto the plug of the circuit
board (point 3).
Note: The plug is reverse-polarity protected. Please do not apply
force when inserting the plug.
Now hook the steel plate with the solar module in the upper edge and

7.
snap the bottom edge in place.

The solar sign illumination is now ready for operation.

4.

3.

4.

Battery take-back

Batteries must not be discarded into domestic

­waste.

- The consumer is legally required to return batteries
after use, e.g. to public collecting centers or to
battery distributors.

- Contaminant-containing batteries are labeled with
the sign “crossed-out trashcan“ and one of the che­mical symbols Cd (= battery contains cadmium), Hg
(= battery contains mercury), Pb (= battery contains
lead). Used batteries should be disposed environmentally friendly and
should not be discarded into domestic waste. Your dealer is legally
required to take back old batteries.

Manufacturer:

esotec GmbH, Etzenrichterstr. 14, D-92729 Weiherhammer
Tel.-Nr: 09605-92206-28, Fax.-Nr: 09605-92206-10,
e-mail: [e-mail] Internet: www.esotec.eu

NiMh

Disposal:

Dear customer,
please cooperate in avoiding waste. When you intend to dispose of the
product in future, please consider that it contains valuable raw materials
suited for recycling.
Therefore, do not dispose it of with domestic waste but bring it to a col
lection point for the recycling of waste electrical and electronic equip­ment.
Thank you very much for your cooperation!

Copyright, esotec GmbHCopyright, all rights reserved.

-