Epson U375 - TM B/W Dot-matrix, TM-U375P Printer User Manual

Download

TM-U375/U375P

User’s Manual

400391309

Printer Part Names

(1) (2)

(3) (4) (5)

(6)

(7)

(8) (9) (10)

Printer cover Control panel Power switch Take-up spool Display module connector Interface connector

Drawer kick-out connector Power connector DIP switches (under a cover)

Cover open recess

Control Panel

VALIDATION/SLIP

All rights reserved. No part of this publication may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, without the prior written permission of Seiko Epson Corporation. No patent liability is assumed with respect to the use of the information contained herein. While every precaution has been taken in the preparation of this book, Seiko Epson Corporation assumes no responsibility for errors or omissions. Neither is any liability assumed for damages resulting from the use of the information contained herein.

Neither Seiko Epson Corporation nor its affiliates shall be liable to the purchaser of this product or third parties for damages, losses, costs, or expenses incurred by purchaser or third parties as a result of: accident, misuse, or abuse of this product or unauthorized modifications, repairs, or alterations to this product, or (excluding the U.S.) failure to strictly comply with Seiko Epson Corporation’s operating and maintenance instructions.

Seiko Epson Corporation shall not be liable against any damages or problems arising from the use of any options or any consumable products other than those designated as Original Epson Products or Epson Approved Products by Seiko Epson Corporation.

EPSON and ESC/POS are registered trademarks of Seiko Epson Corporation in Japan and other countries/regions.

Standards and Approvals

The following standards are applied only to the printers that are so labeled. (EMC is tested using the Epson power supplies.)

Europe: CE marking North America: FCC/ICES-003 Class A Oceania: AS/NZS CISPR22 Class A

WARNING

This is a Class A product. In a domestic environment this product may cause radio interference in which case the user may be required to take adequate measures.

The connection of a non-shielded printer interface cable to this printer will invalidate the EMC standards of this device. You are cautioned that changes or modifications not expressly approved by Seiko Epson Corporation could void your authority to operate the equipment.

CE marking

The printer conforms to the following Directives and Norms: Directive 2004/108/EC

EN 55022 Class A EN 55024

IEC 61000-4-2 IEC 61000-4-5 IEC 61000-4-3 IEC 61000-4-6 IEC 61000-4-4 IEC 61000-4-11

FCC Compliance Statement for American Users

This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment.

This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications.

Operation of this equipment in a residential area is likely to cause harmful interference, in which case the user will be required to correct the interference at his own expense.

For Canadian Users

This Class A digital apparatus complies with Canadian ICES-003.

À l'intention des utilisateurs canadiens

Cet appareil numér ique de classe A est conforme à la norme canadienne NMB-003.

Restriction of Use

When this product is used for applications requiring high reliability/safety, such as transportation devices related to aviation, rail, marine, automotive, etc.; disaster prevention devices; various safety devices, etc.; or functional/ precision devices, etc.; you should use this product only after giving consideration to including fail-safes and redundancies into your design to maintain safety and total system reliability. Because this product was not intended for use in applications requiring extremely high reliability/safety, such as aerospace equipment, main communication equipment, nuclear power control equipment, or medical equipment related to direct medical care, etc., please make your own judgment on this product’s suitability after a full evaluation.

Introduction

Features

The TM-U375 and handle slip, validation, and journal printing (both journal and receipt printing with pressure-sensitive paper) in a single unit. The main features of the TM-U375 and

World’s smallest multi-function 1.5 station printer.

High-speed printing using logic seeking.

Easy problem handling (e.g., paper jams or objects dropped into the printer) via a clamshell mechanism.

Two validation/slip paper entrances: from above for validation paper

and from the front for slip paper.

U Free-format printing in page mode. Q Various check printing pattern. Cl

Logic seeking and page mode for check printing.

Movable platen for easy paper insertion.

Paper load switch for easy paper roll loading.

Control capability for two drawers.

Selectable character size (7 x 9 font or 5 x 9 font).

Q Command protocol based on the Q

ASB

(Automatic Status Back) function that automatically transmits

printer status changes.

EPSON® intelligent module connection (for the TM-U375 only).

EPSON display module series connection (for the TM-U375 only).

Bidirectional parallel interface in accordance with the IEEE 1284

Nibbe/Byte Modes.

TM-U375P

are high-performance

printers are as follows:

ESC/POS@

standard.

POS

printers which

About This Manual

Setting up and Using

Chapter 1 contains information on unpacking the printer, setting it up,

setting the DIP switches, and adjusting the paper near end detector.

Chapter 2 contains information on using the printer.

LI Chapter

3 contains troubleshooting information.

iii

Reference

Chapter 4 contains specifications.

Notes, Cautions, and Warnings

Note:

Notes have important information and of your

printer.

CAUTION:

useful

tips on the operation

Cautions must be observed to avoid minor yourself or

damage to your equipment.

WARNING:

Warnings

bodily injury.

must be followed carefully to avoid serious

injury

Contents

Chapter 1 Setting Up the Printer

Unpacking....................................................

Removing the Protective Materials Downloading Drivers, Utilities, and Manuals .

Connecting the Printer to Your Computer. Connecting the Printer to Your Drawer.

Anschließen Connecting the Printer to Your Direct Connection Display Module

Grounding the Printer Connecting the Power Supply Installing the Ribbon Cassette Installing the Paper Roll Running the Self-test

Running the self-test with paper roll Running the self-test with the slip paper

Running the self-test with validation paper.....................

Setting the DIP Switches

TM-U375 DIP-switch functions.

TM-U375P DIP-switch functions Adjusting the Paper Roll End Sensing Position Using the Power Switch Cover

des Druckers an Ihre Geldladee

............................................

..........................................

.............................................

.........................................

.................................

...........................

.............................

..........................l-8

(For the TM-U375 only)..........

.....................................

..........................

.......................

.............................

.......................l-23

....................................

l-2 l-2 l-4

l-4 l-6

1-10 l-11 1-12 1-14 1-16

1-18 1-18 1-18 l-19 l-20 l-21 l-22

l-25

Chapter 2 Using the Printer

Operating the Control Panel

Buttons................................................

Indicator lights..........................................

Slip Paper Handling............................................

Validation Paper Handling.......................................

Replacing the Paper Roll........................................

Replacing the Ribbon Cassett

Removing the ribbon cassette. ..............................

Installing the ribbon cassette . .............................

Aerosol sprayer caution . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-9

.....................................

e...................................

. .

2-2 2-2 2-2 2-4 2-4 2-5 2-6 2-7 2-8

Chapter

3 Troubleshooting

Troubleshooting................................................

General problems Printing problems Paper handling problems

Hexadecimal Dumping.

Starting hexadecimal dumping Ending hexadecimal dumping

Chapter

Printing Specifications

Character Specifications

Paper Specifications. Electrical Specifications.

Electrostatic Protection (measured based on the IEC801-2 test conditions) . 4-6 Reliability. Environmental Specifications Interface Specifications Printing on Cut Sheets

Transmit Status Identificationn Notes On Number of Printable Columns

4 Reference

....................................................

Example print control for cut sheet

.........................................

...................................

..........................................

...............................

Information

...........................................

.........................................

............................................

.........................................

.....................................

..........................................

...........................................

...........................

.....................................

.............................

3-2 3-2

3-2 3-4

3-6 3-6 3-7

4-2 4-2 4-3 4-6

4-6 4-7

4-8 4-8

44-11 4-12

Chapter

Setting Up the Printer

Setting Up the Printer 1-1

Unpacking

The illustration below shows the items included for the standard specification printer.

Take-up spool

Paper roll (1

pc)

Ribbon

cassette

Power switch cover

Removing the Protective Materials

The printer is protected during shipping by protective materials that must be removed before you turn on the printer.

Loosen the screw and remove the protective material A from the printer, as the illustration shows on page 1-3.

1-2

Setting Up the Printer

Protective material

Note:

Store the steps below.

the

protective material A on the back of

the

printer, following

1.Insert the projections on corresponding holes as

Tighten the

Protective material A

screw.

the

protective material A into

the

illustration below.

the

Note:

Q&l

Put

the

protective material A back in its original position if you ever

ship

or store your printer.

Setting Up the Printer

1-3

2. Remove the protective materials and

as the illustration.

Note:

Put the protective materials B and C back in their original position if you ever ship or store your printer.

Downloading Drivers, Utilities, and Manuals

Drivers, utilities, and manuals can be downloaded from one of the following URLs.

Protective material

For customers in North America, go to the following web site: http://www.epsonexpert.com/ and follow the on-screen instructions.

For customers in other countries, go to the following web site: http://www.epson-pos.com/

Connecting the Printer to Your Computer

TM-U375

Follow the procedures below only when you use the printer as a single unit

(not connected to an intelligent module). When you use the printer with the

intelligent module, refer to the You need an appropriate serial interface cable to connect your computer to

the printer’s built-in interface.

Make sure that both the printer and computer are turned off; then plug the cable connector securely into the printer’s interface connector.

IT-U Series User’s Manual for details.

Tighten the screws on both sides of the cable connector.

1-4 Setting Up the Printer

Your printer comes with inch-type hexagonal lock installed. millimeter-type lock screws, replace the inch-type screws with the millimeter-type screws by using a hex screwdriver

mm). To distinguish the two types of screws, see the figure

below.

If you

Notch (one or more lines)

plan to use an interface cable

that

screws

requires

Plug the other end of the cable into the computer.

TM-U375P

You need an appropriate parallel interface cable to connect your computer

to the printer.

Make sure that the printer and the computer are turned off. Then plug the cable into the connector on the printer, as shown.

Inch-type

Millimeter-type

Setting Up the Printer 1-5

Note:

Squeeze the wire clips on the printer

place on

Connect the other end of the cable to the connector on your computer.

both

sides of

the

connector.

together

until

Connecting the Printer to Your Drawer

Follow the procedures below to connect a drawer to the printer only when you use the printer as a single unit (not connected to an intelligent module).

(Intelligent module connection is available only for the TM-U375.) When you use the TM-U375 with the intelligent module, refer to the

User’s Manual

Use Using an well as

for details.

a drawer

improper

the

printer.

that

matches the

drawer

printer

may damage the drawer as

they

lock in

IT-U Series

specification.

Make sure that the printer is turned off.

Plug the cable connector securely into the printer’s drawer kick-out connector until it clicks.

1-6 Setting Up the Printer

TM-U375

TM-U375P

A CAUTIONS:

not connect

out

connector. Do the

not

display

a telephone

confuse the drawer

module connector.

line

the drawer kick

kick

out connector and

Setting Up the Printer

1-7

Anschließen des Druckers

lhre Geldlade

Verfahren

Drucker anzuschließen,

angeschlossen an ein intelligentes Modul) betrieben betr. Verwendung Betriebsanleitung der IT-U

Sie wie

im folgenden beschrieben, um eine Geldlade an den

aber

nur, wenn der Drucker

des

Druckers mit einem intelligenten Modul siehe

Serie.

A ACHTUNG:

Nur

eine

Geldlade verwenden, Druckerspezifikation ungeeigne ten Geldlade such

Stellen

Stecken Steckverbinder am Drucker ein, bis er hörbar einrastet.

TM-U375

der Drucker beschäaligt werden.

Sie

sicher,

Sie

den Kabelsteckverbinder fest in den Auszug-

daß

der Drucker ausgeschaltet

entsprich t. Bei

kann

die

der Verwendung einer

sowohl

als

Einzeleinheit (nicht

wird.

Einzelheiten

die

Geldlade

ist.

als

1-8

Setting Up the Printer

TM-U375P

ACHTUNG:

Am Auszug-Steckverbinder

Telefonleitung anschließen.

icht den Auszug-Steckverbinder für die Geldlade

2. und

den

Displaymodul-Steckverbinder vetwechseln.

für die

Geldlade

keine

Setting Up the Printer

1-9

Connecting the Printer to Your Direct Connection Display

Module (For the

Follow the procedures below to connect a direct connection display

module to the printer only when you use the printer as a single unit (not connected to an intelligent module). When you use the printer with the intelligent module, refer to the

Make sure that the printer is turned off.

Plug the cable connector (provided with the direct connection display module) securely into the printer’s display module connector until it

clicks.

TM-U375

only)

IT-U Series User’s Manual for details.

A CAUTIONS:

not

out

connector.

not

display

the

Never connect any module to the DM connector.

4.If you connect module to the DM connector, Corporation product

1-10

Setting Up the Printer

connect a telephone

confuse the drawer

module connector.

product other

any product

is not liable for any

or to the

TM-U375 itself.

kick out connector

other than the

line

to the drawer

than the

Seiko

Epson

damage to the other

kick

and

display

Grounding the Printer

When you use the printer as a single unit (not connected to an intelligent

module), you need to ground your printer. (Intelligent module connection

is available for the TM-U375 only.)

Recommended wire is described below. Thickness of wire Diameter of terminal to be attached

Make sure that the printer is turned off.

Connect the ground wire to the ground connector (marked FG) on the bottom of the printer with the screw provided on the printer. Alternatively, another screw located beside the power connector on the TM-U375P can be used to connect the ground wire.

TM-U375

: AWG18

or equivalent

3.2

Setting Up the Printer

1-11

TM-U375P

Ground the other end of the ground wire.

Connecting the Power Supply

When the printer is used as a single unit, not connected to an intelligent module, use the specified EPSON power supply for your printer. When the printer is connected to an intelligent module, the power is supplied by the intelligent module. Refer to

the IT-U Series User’s Manual

for details. (Intelligent module connection is available for the TM-U375 only.)

Using an electrical

When from the printer,

plugged

damage the

incorrect

power supply

may

cause fire

shock.

connecting or disconnecting the

make sure that

to an electrical outlet; otherwise

power

supply or the

the

printer.

power

supply

supply is not

you

may

Make sure that the printer’s power switch is turned off, and that the power supply’s power cord is unplugged from the electrical outlet.

1-12

Setting Up the Printer

Check the label on the power supply to make sure that the required voltage matches that of your electrical outlet.

Plug the power supply’s DC cable connector into the printer’s power connector as shown below.

TM-U375

TM-U375P

Plug the power supply’s power cord into an electrical outlet.

Note:

remove

and pull it

cord is unplugged before you disconnect the DC cable connector.

the DC

straight

cable

connector, grasp

out. Make sure

that the

the

connector at the arrow

power

supply 's

power

Setting Up the Printer

1-13

Installing

the Ribbon Cassette

A CAUTIONS:

Never direction of the arrow marked on the cassette; otherwise the ribbon cassette may be damaged.

Be sure replace a

Note:

Use

Turn on the printer and open the printer cover.

Turn the ribbon cassette’s knob two or three times in the direction of the arrow, to take up any slack in the ribbon.

turn

the ribbon

the printer is

ribbon

the

EPSON ERC-38 ribbon cassette for your printer.

cassette; otherwise

cassette’s

not

receiving

knob in the opposite

data when you

data may

times

lost.

Insert the ribbon in the position as the illustration below and push the ribbon cassette until it clicks. Then rotate the cassette’s knob two or three more times. This is necessary to place the ribbon in the correct position.

1-14

Setting Up the Printer

or 3more times

Knob

Make sure that the ribbon is installed between the print head and the

ribbon mask without wrinkles or creases, as shown below.

Print head

Note:

Q3.l

the

ribbon is not installed

grasp

then

the

cassette's tab on

pull

the

cassette out of

above to install

correctly,

the

left side,

the

printer.

the

ribbon cassette again.

to remove

lift the left

Repeat steps

the

ribbon cassette,

side out first, and

3 and

Tab

Setting Up the Printer

1-15

Installing

Use a paper roll that matches the specifications.

Fold the paper so it is exactly straight and even, as shown in the

illustration, and will not tear off jaggedly.

the Paper Roll

Note:

The

printer must be turned on before installing

the

paper roll.

Turn on the printer, open the printer cover, and remove the take-up

Insert the paper roll as shown below.

Correct

spool.

Insert the tip of the paper into the paper inlet as far as it will go, and push the PAPER LOAD switch comes out from the top of the printer. Note that the arrow in the exploded drawing below points towards the front of the printer.

1-16

Setting Up the Printer

to feed the paper roll until the paper

Paper inlet

PAPER LOAD switch

When using the take-up spool, follow the steps and the illustration below.

Pull out the side of the take-up spool and insert the tip of the paper roll into the groove on the spool as the illustration below.

Rotate the spool two or three times to secure the paper and reinsert

the side of the take-up spool as the illustration below.

Install

Tear off the receipt paper on the cutter; then close the printer cover.

Note:

inactive.

the

When the

take-up spool in the printer.

2 or

printer cover is open,

the

PAPER FEED

Setting Up the Printer

button is

1-17

Running the Self-test

Any time that you want to check the performance of your printer you can run the self test described below. This shows whether your printer is

working correctly. It is independent of any other equipment or software. You can run the self-test with the paper roll, slip paper, or validation paper.

Running the self-test with paper roll

Note:

4. The self-test automatically ends after printing

Be sure to install

run

the

self test.

Make sure the printer is turned off and the printer cover is closed properly. While holding down begin the self-test. The self-test prints the printer settings and pauses printing. (The JOURNAL OUT light flashes.) Press the PAPER FEED button to continue printing. The self-test prints some lines of characters from the character table.

the paper. The printer becomes ready to receive data from the computer after the self-test. Self-test mode switches to normal mode.

the

ribbon cassette and

the

PAPER FEED button, turn on the printer to

the

paper roll before you

"***

completed

***"

Running the self-test with the slip paper

Note:

1-18

2.Hold down the RELEASE button and turn on the printer to begin the

Setting Up the Printer

Be sure to install

Make sure the printer is turned off and the printer cover is closed properly.

self-test. The VALIDATION/SLIP light flashes. Feed a sheet of slip paper into the printer. The self-test loads the paper automatically, prints the printer settings, and then ejects the paper. The VALIDATION/SLIP light flashes. Remove the paper and feed another sheet of slip paper into the printer to print characters from the character table. Continue to feed slip paper

into the printer until

the

paper roll in

the

self-test prints

the

printer to prevent

"***

completed

slip

paper jams.

***".

The self-test automatically ends after printing The printer is ready to receive data from the computer after the self-test completes.

6. Self-test mode switches to normal mode.

"***

completed

Running the self-test with validation paper

Note:

Be sure to install

paper jams.

Make sure the printer is turned off and the printer cover is closed properly. Hold down the PAPER FEED and RELEASE buttons and turn on the printer to begin the self-test. The VALIDATION/SLIP light flashes. Feed a sheet of validation paper into the printer. The self-test prints the printer settings, and then ejects the paper. The VALIDATION/SLIP light flashes. Remove the paper and feed another sheet of validation paper into the printer to print characters from the character table. Continue to feed validation paper into

***".

the

paper roll in

the

printer until the self-test prints

the

printer to prevent validation

"***

completed

***".

The self-test automatically ends after printing The printer is ready to receive data from the computer after the self-test completes.

Self-test mode switches to normal mode.

Note:

you want to pause validation paper at any point, press the

PAPER FEED button again to resume

the

self-test for

the

"***

completed

paper roll, slip paper, or

PAPER FEED button. Press

the

self-test.

***".

Setting Up the Printer

1-19

Setting the DIP Switches

Turn off to prevent an

the printer

electrical short,

while

removing the DIP switch cover

which

can damage the

printer.

You can change your interface and print column settings by changing DIP switch settings.

1. Make sure the printer is turned off.

Remove the screw from the DIP switch cover. Then take off the DIP switch cover, as shown in the illustration below.

the

There are two sets of switches. Notice that ON is marked on each set of

switches. Use tweezers or another narrow tool to move the switches.

Use the following tables to set the DIP switches. Numbers starting with

1 are in the first set, and numbers starting with 2 are in the second.

1-20

Setting Up the Printer

TM-U375 DIP-switch functions

DIP Switch Set 1

SW Function

l-1 Data reception error

Receive buffer capacity

l-2 l-3 Handshaking l-4Word length

Parity check

1-5

Parity selection

l-6

Transfer speed (see table below)

l-7 l-8 Transfer speed (see table below)

Transfer Speed (BPS)

1200

2400 4800 9600

BPS: Bits Per Second

DSW2 SW

2-l Connection of display module

(see Note 1 on the next page)

Selects number of characters

2-2

per line

7 X 9 font/5 X 9 font (refer to the

Function

(CPL)

Notes on Number

Printable Columns

Ignored

bytes

XON/XOFF

7 bits

Yes

Even

SW7

ON OFF ON OFF

Connected

CPL/

35 CPL

section in Chapter

OFF

Prints

DTR/DSR

8 bits

Odd

SW8

ON ON OFF OFF

OFF

Not connected

40 CPU

bytes

CPL

Handshaking operation

2-3

(busy condition) For internal use only.

2-4

For internal use only.

2-5

For internal use only.

2-6

Pin 6 reset signal

2-7

(see Note 2 on the next page)

2-8

Pin 25 reset signal

(see Note 2 on the next page)

not

change the settings of switch

Receive

buffer full receive buffer full

Used

2-4, 2-5

Setting Up the Printer

Off-line or

Not used

and

2-6.

1-21

Notes:

This function can be used only when a direct connection display

module is connected to the display module connector.

2..

DIP switch settings cannot be changed after the power is turned on or turning 7 and 8.

after

the printer is reset through the interface.

the

power on, do not change

TM-U375P DIP-switch functions

DIP Switch Set 1

the

settings of DIP

When

switches

SW Function

1-1

Auto line feed l-2 Receive buffer capacity l-3 Undefined l-4 Undefined 1-5 Undefined 1-6

Undefined l-7 Undefined l-8 Undefined

Enabled

40 bytes

DIP Switch Set 2

1 Undefined

2-2 Print column selection

2-3 Handshaking (busy condition)

2-4 Reserved. 2-5

Settings must not be changed.

2-6

Settings must not be changed. 2-7 Undefined 2-8

nInit reset signal Fixed to ON.

Function

9 font/9 X 9 font

42CPL/35CPL

Receive

buffer full

ON OFF

receive buffer full

OFF

Disabled 4K

bytes

40CPL/33CPL

Off-line or

A CAUTION:

not

change the settings of switch

Replace

1-22 Setting

the

DIP switch cover and secure it

the Printer

2-4, 2-5, 2-6 and 2-8.

with

the screw.

Note:

attach the

the

cover

DIP switch cover, insert

leftward,

shown

the

cover upward

the

illustration below.

then

Adjusting the Paper Roll End Sensing Position

slide

The paper near end detector detects when the paper is almost gone by

measuring the diameter of the paper roll. Software programs can use the

ESC

4 command to stop printing when the paper is almost gone.

If you want to change the amount of paper remaining when the printer stops printing, follow the steps below to adjust the paper near end detector.

Note:

the

inner diameter of

inch),

the

paper roll near-end detector may not work properly.

the

paper roll core is less

than

10 mm

(0.39

1. Open the printer cover and remove the take-up spool.

Determine the point on the paper roll at which you want the near-end detector to be triggered. Then measure the distance A shown in the

illustration.

Setting Up the Printer

1-23

Distance A

Notes:

Find the corresponding adjustment position number from

There may be some difference between

and

the

actual sensing position.

the

measured distance A

the

table below.

Distance A

10 mm (0.39 inch) 8 mm (0.32 inch) 6 mm (0.24 inch)

mm (0.16 inch)

mm (0.08 inch)

Loosen the detector screw with a coin or screwdriver.

Set the detector scale to the position you determined from the table by

moving the detector screw up or down. The numbers not marked on

the

detector scale. Use the illustration below for reference.

Adjustment position number

#2 #3

#4 #5

#1, #2, #3...

Detector scale

are

Detector scale

Secure the detector screw; then replace the take-up spool and close the printer cover.

1-24

Setting Up the Printer

Using

You can use the provided power switch cover to protect the power switch from accidental or improper operation. Attach the cover as shown in the

illustration below.

You can turn the power on or off with the switch cover attached by inserting a pointed object (like a ball point pen) through either of the two

small holes on the switch cover.

the

Power Switch Cover

Push to attach the cover.

If an accident attached, unplug the immediately.

occurs

when power supply

the

power

Setting Up the Printer

switch cover

cord

from

the outlet

1-25

Chapter 2

Using the Printer

2-1

Operating the Control Panel

The control panel has two buttons and four lights.

Buttons

The control panel buttons perform paper feeding and release functions.

PAPER FEED

Press the PAPER FEED button once to advance paper one line. You can

also press the

RELEASE

PAPER FEED

button continuously to feed the paper continuously.

Press

the

RELEASE button to release the paper clamp.

lndicator lights

The control panel lights provide information on printer conditions.

POWER (green)

The POWER light is on when the printer power is on.

ERROR (red)

The

ERROR

The ERROR light is on under the following conditions:

When you first turn on the printer or after you reset the printer using the interface. The ERROR light goes off after the printer is initialized.

When the printer cover is open. Close the printer cover if this is the case.

l When the printer stops printing because it senses the paper roll end.

Install a new paper roll if this is the case.

light is on or is flashing when the printer is not ready to print.

2-2 Using the Printer

Slip

Paper Handling

Use only slip paper (flat paper without wrinkles, creases, or folds) that matches the specifications.

Note:

Be sure to install the paper

print only on slip paper. This will prevent paper jams.

Send the appropriate control commands from the computer to print on

slip paper.

When the VALIDATION/SLIP light flashes, insert a slip into the slip paper inlet as shown in the illustration below.

Make sure you insert the slip paper into the inlet as far as it will go.

roll

in the printer, even if you plan to

The paper will automatically be drawn in and printing will begin.

Note:

When the application software), remove the paper from

VALIDATION/SLIP

Validation Paper Handling

Use only validation paper (flat paper, without wrinkles, creases, or folds) that matches the specifications.

Note:

2-4 Using the Printer

Be sure to install

print only on validation paper.

the

paper roll in

light

flashes

the

printer, even

This

will prevent paper jams.

(this depends

the

paper

on the

path.

you plan to

1. Send the appropriate control commands from the computer to print on validation paper.

2.When the VALIDATION/SLIP light flashes, insert a sheet of validation

paper into the validation paper inlet (see the illustration below); printing will then begin.

Make sure you insert

Note:

When the

application software), remove

VALIDATION/SLIP light flashes (this depends on the

the

validation paper into the inlet as far as it will go.

Replacing the Paper Roll

To change the paper roll, follow the steps below.

the

paper from

the

paper

path.

Cut the journal paper on the cutter; then remove the take-up spool.

Using the Printer 2-5

Pull out the paper roll and cut the paper, as the illustration below.

Press the PAPER LOAD switch and remove the paper in the direction

of the arrow, as the illustration below.

Never pull

Reinstall a new paper roll by following the steps in

Roll

in Chapter 1.

out

the

paper roll manually.

Replacing the Ribbon Cassette

PAPER

LOAD switch

Installing

the Paper

Never opposite direction of the arrow marked on the cassette; otherwise the ribbon cassette may be damaged.

Be sure the printer replace a ribbon cassette; otherwise

Note:

2-6 Using the Printer

Use

turn the

the

EPSON-ERC-38 ribbon cassette for your printer.

ribbon cassette’s feed

is not

receiving data when

knob in the

you

data

may be

lost.

Note:

Qsh

There

are two ways to replace

printer off and on again before installing or removing

cassette, making sure (When is lost.) The

you turn off

other

that

the

printer power, data sent from

is to open

data

the

sent

printer cover and press

RELEASE button before installing or removing

Both

ways cause

and

the

ribbon

paper clamp to release. If one of might

the

print head to move to

not be inserted or removed correctly.

Removing the ribbon cassette

Turn the printer power off and on again; then open the printer cover.

Grasp the ribbon cassette’s tab on the left side, lift the left side out first,

and then pull the cassette out of the printer, as shown in the illustration below.

ribbon cassette. One is to turn

the

ribbon

from

the

computer is not lost.

the

computer

the

ribbon cassette.

the

center of

these

ways is not used,

the

printer

the

Tab-

Using the Printer

2-7

Installing the ribbon cassette

Turn the ribbon cassette’s knob two or three times in the direction of the

any

arrow, to take up

Insert the ribbon in the position as shown below, and push the ribbon cassette into the printer until it clicks. Then rotate the cassette’s knob two or three more times. This is necessary to place the ribbon in the correct position.

slack in the ribbon.

or 3 times

2-8

Using the Printer

Make sure that the ribbon is installed between the print head and the ribbon mask without wrinkles or creases, as shown below.

Print head

Note:

Remove

printer for a long time.

CAUTION:

Do not use aerosol sprayers containing flammable gas inside or around this product. Doing so may cause fire.

the

ribbon cassette from the printer when you store the

Using the Printer 2-9

Chapter 3

Troubleshooting

Troubleshooting 3-1

Troubleshooting

Read this section if you have a printer problem.

General problems

The lights on the control panel do not come on.

Make sure that the power supply’s DC cable is properly plugged into the printer’s power connector.

Make sure that the power supply’s power cord is properly plugged in the AC inlet of the power supply.

Make sure that the power supply’s power cord is properly plugged into the electrical outlet.

Printing problems

The ERROR light is on (not flashing) and nothing is printed.

If the JOURNAL OUT light is on:

The paper roll is not installed, or the paper roll is nearly or completely

depleted. Install a new paper roll in the printer.

Roll

in Chapter 1.

the JOURNAL OUT light is off:

Make sure that the printer cover is properly closed.

The ERROR light is flashing and the printer does not print.

First, turn off the printer and check for a paper jam. (See the paper jam

description on page 3-4.)

See

Installing

the Paper

3-2 Troubleshooting

If there is no paper jam and the printer has been printing for quite a while, the print head may be overheated. If the print head is overheated, the printer will resume printing when the head has cooled (usually within two

or three minutes).

If there is no paper jam and the print head is not overheated, turn off the printer and turn it back on after about 10 seconds. If the printer still does not work, unplug the power supply cord from the outlet immediately. Then contact a qualified service person.

The ERROR light is off but nothing is printed.

Try to run the self-test to make sure that the printer works properly. See

Self-test later in this section. If the self-test does not work, contact your

dealer for assistance.

If the self-test works properly, check the following:

Check the connection at both ends of the interface cable between the

printer and the computer. Make sure that this cable meets the

specifications for both the printer and the computer.

The data transmission settings may be different between the printer and

the computer. Make sure that the printer’s DIP switch settings for data transmission are the same as the

computer's.

interface settings using the self-test. See

You can print the printer’s

Running the

Self-test

in Chapter 1.

If the printer still does not print, contact your dealer for assistance.

The printer sounds like it is printing, but nothing is printed.

The ribbon cassette may not be installed properly. See

Ribbon Cassette

in Chapter 2.

Replacing the

The ribbon may be worn out. Replace the ribbon cassette as described in

Replacing the Ribbon Cassette in Chapter 2.

Troubleshooting 3-3

4. Cut the paper roll.

Remove the paper jam while pulling the release lever toward you, and pull the paper out in the direction of the arrow as shown in the illustration below.

Notes:

Q?l

1..

Never pull out the jammed paper in the opposite direction from the ejection side

Pull out make sure you remove any remaining pieces.

the

Release lever

the printer.

paper gently in the paper feeding direction, and

Left side of the printer

Press down the print head cover after confirming that the print head is

at the center of the printer. If the print head is not at the center of the

printer, bring it to the center by holding the base of the print head.

Troubleshooting

3-5

Close the print head cover. The cover clicks when it is closed securely.

Install the ribbon cassette, following the steps in Replacing the Ribbon

Cassette

Install the paper roll, following the steps in Chapter 1.

10. Close the printer cover.

The remaining amount of paper roll is not detected correctly.

If a paper roll with a red end mark at the paper end is used, the mark may cause the paper to stick together. If this occurs, the paper roll near-end detector may not work properly. (See

Sensing Position

in Chapter 2.

in Chapter 1.)

Installing

Adjusting the Paper Roll End

the Paper Roll in

Hexadecimal Dumping

This feature allows experienced users to see exactly what data is coming to the printer. This can be useful in finding software problems. When you turn on the hex dump function, the printer prints all commands and other data in hexadecimal format along with a guide section to help you find

specific commands.

Starting hexadecimal dumping

Open the printer cover and turn on the power while pressing the PAPER

FEED button, then close the cover. The printer first prints “Hexadecimal

Dump” on the paper roll, and prints the data received thereafter in

hexadecimal numbers and their corresponding characters.

Notes:

Q&L

“. ”

is printed if no character corresponds to the

Control commands are printed in bold for emphasis.

During hexadecimal dumping, all commands except

and

DLE ENQ

are disabled.

data

received.

DLE EOT

3-6 Troubleshooting

If there is insufficient print data to fill one line (such as at the

end of a hexadecimal dump), the data will not print.

(This means that 8-byte data is required to print on one line.) remaining data in this case can be printed by placing the printer in off-line mode by opening the cover or pressing the PAPER

FEED button.

The

Example

inting

Hexadecimal Dump

21 001B 26

lB2.5 01

41 42 4344 45

lB63

0240 34001B 4647

Ending hexadecimal dumping

End hexadecimal dumping by turning off the power or by resetting the printer after printing completes.

.!..&@@

.%..c4..

ABCDEFGH

Troubleshooting 3-7

Chapter

Reference Information

Reference Information 4-1

Printing Specifications

Printing method: Head wire layout:

Serial impact dot matrix

Serial type 9-pin 1/72 inch

Printing direction:Bidirectional, minimum distance printing (logic seeking) Printing speed:

Approximately 3.5 (40 columns,16 CPI, continuous printing) Approximately 5.4 (20 columns,16 CPI, continuous printing) (LPS: Lines Per Second;

Note:

During the

excessive

actual printing

use, printing stops to protect the print head.

speed

may be slower than that listed above.

Characters per line: See the table below. Characters per inch: See the table below.

Character Specifications

Number of characters:

Character structure:

Character size:

Alphanumeric Extended graphics:

(space pages included) International:

9 (total horizontal dot positions: 400 half dots)

7 5

9 (total horizontal dot positions:

See the table below.

LPS

CPI:

Characters Per Inch)

In this case,

128

X 8

(tables)

200

dots)

4-2 Reference Information

(*)

Default font is 7 X 9.

Paper Specifications

Paper feed method: Paper feed pitch:

Friction feed

l/6

inch (default)

Programmable in units of

1/144

inch by using

commands.

Paper feed speed:

Approximately 2.67

IPS

(16 LPS)

(continuous paper feeding)

Paper size:

a) Paper roll

Paper width:

0.5 mm (2.99" ?

.02")

Outside diameter:

l Single-ply paper: Journal paper only:

(with take-up flange diameter of Receipt paper only:

l 2-ply paper:

Inside diameter:

83 + 0 mm (3.27") or less (lower paper must be taken up)

10 mm

(.39")

or more

60 + 0 mm (2.36") or less

75 mm (2.95"))

83 + 0 mm (3.27") or less

@ Normal paper

Paper thickness: Single-ply paper:

0.06 to 0.085 mm

(.OO24

.0033")

@ Multi-ply paper

Paper thickness:

0.05 to 0.08 mm Total thickness: 0.16 mm

.0031")

(.0063")

per sheet or less

(.0020

Maximum number of sheets:

2 (1 original

1 copy)

Recommended paper: Mitsubishi Paper Mills Co., no-carbon paper (blue)

Upper sheet: Lower sheet:

N4OHi N60

(thickness: 0.06 mm (.0023"), weight: 47.2

(thickness: 0.08 mm (.0031”), weight: 68.0

g/m2)

Cut sheets:

Paper types:

Paper size (W X

@ Slip paper:

@ Validation paper: 135 to 182 mm X 70 to 257 mm (5.3 1 to 7.17"

l Single-ply paper (without copy paper)

Thickness:

Slip/validation paper (Use cut sheet with a paper roll loaded.)

Normal, pressure sensitive, and carbon copy paper

L):

160

70 to 182 mm

6.30 to

10.12")

(maximum 58 lines at 4.23 mm

to 257 mm (2.76 to 7.17"

(.17")

2.76 to 10.12") (maximum 16 lines at 4.23 mm

0.09 to 0.12 mm

(.0035

(.17")

.0047")

Reference Information 4-3

pitch)

l Copy paper

Thickness: Backing paper:

Copy and original paper:

Carbon copy paper:

Total thickness:

Example: Original

Original paper: Carbon copy paper: Copy paper: Backing paper: Roll paper:

2-ply copy

0.04

mm (.0016")

0.07 mm

0.04

mm (.0016")

0.07

mm (.0028")

0.08

mm (.003

(.0028")

1")

0.07 to 0.12 mm (.0028 to

0.04

(.0016

.0047")

to 0.07 mm

to. 0028") Approximately 0.035 mm (.00138")

0.09 to 0.31 mm (.0035 to

.012")

(roll paper thickness included)

(0.035 mm

(.0014")X2

sheets)

Total thickness:

0.30

mm (.0118")

Copying capability:

As copying capability is influenced by the ambient temperature, printing must be performed under the conditions described in the table below.

Relationship between Ambient Temperature and Number of Copies

Number of Copies

Original

2-ply copy

Original + l-ply copy 5° to 40°C (41° to

Notes

on using

l Use cut sheets with a paper roll loaded. l Use cut sheet that is flat, without curls, folds, warps, or wrinkles, especially at

cut sheets

Ambient Temperature

10°

40°C (50°

to 104°F)

104°F)

the paper end. Otherwise, the paper may become ink stained or the ribbon may get caught in the printer mechanism.

Especially slip paper with curls at the paper end may cause character

(.67")

misalignment within the area about 17 mm

l Glue must not be on the bottom edge of slip paper. It is desirable that the

from the paper edge.

glue should be on the top edge of slip paper. Choose slip paper carefully when the glue is on the right or left edge of the slip paper, since paper feeding and paper insertion are affected by gluing conditions (e.g., glue quality, method, and length) and glue location (refer to the figure in the next page). Be careful especially when slip paper is wide and has the glue on the right or left edge, since meandering may occur.

4-4 Reference Information

Do not use

Use carefully

Paper feeding direction

Glue Location of Slip paper

Cut sheets with holes (e.g., sprocket holes) within the areas shown in the figures below must not be used. Otherwise, the paper cannot be detected by the paper detector. Paper that is translucent must not be used.

Validation paper

: Holes

are prohibited in

this area.

Inserting direct1

6 3

Srnrn(.3z?)

Slip paper

lOmm(.98”)

Glued

area

: Holes

are

prohtbited

Inserting

direction

in s

1‘

l Use of multi-ply copy paper with a thick middle sheet may decrease copying

sure to disable paper-end

detection (using ESC c

before printing.

in this

capability.

l Printing noise may change depending on paper thickness. Noise may

increase when thick single-ply paper is used.

Reference Information

4-5

Electrostatic Protection (measured) based on the IEC801-2 test conditions)

Air discharge: 8K V clear level

4K V clear levelContact discharge:

* Be sure to use a safety-standards-applied power source that meets the following specifications. Rated output: 24 V/2.0 A or more, Maximum output: 240 VA or less

Environmental Specifications

Temperature:

Operating: 5° to 40°C (41° to 104°F)

Storage:

Humidity:

Operating: 20 to 80%RH (see the range in Figure A.10 below, for 30°C (86°F) and above, without condensation) Storage: 20 to 90%RH (excluding paper and ribbon, without condensation)

- 10° to 50°C (14° to 122°F) (excluding paper and ribbon)

Vibration resistance:

When packed:

Impact resistance:

When packed:

When unpacked:

temperature

Frequency: 5 to 55 Hz Acceleration: 2 G Sweep: Time: Directions:

10 minutes (half circle) 1 hour

X, Y, and Z No external or internal damage should be found after the vibration test, and the printer should operate normally.

Package:

Height: Directions:

Epson standard package

60 cm (23.62")

1 corner, 3 edges, and 6 surfaces No external or internal damage should be found after the drop test, and the printer should operate normally.

Height: Directions:

5 cm (1.97")

Lift one edge and release it (for all 4 edges) A non-operating printer should not be damaged after it is dropped (for all 4 edges).

Reference Information 4-7

Acoustic noise:

terface

Operating:

Specifications

Approx. 65 dB or less (Bystander position,

receipt/journal

printing)

Serial interface: Parallel interface:

Note:

Refer

RS-232 compatible

IEEE 1284 compatible (Nibble/Byte Modes)

the

EPSON

TM-U375/U375P

Printing on Cut Sheets

Use

the

Step

Host

command.

Insert the paper. Detects the cut sheet and turns on the

Transmit data and Prints the data and feeds the paper.

commands. Transmit the FF After printing, ejects the paper and selects paper roll

command.

following

Transmit the

procedure

Operation

ESC c

0 Switches to cut sheet mode and waits for a cut sheet to

Specification for details.

to print on slip or validation paper.

Printer

be loaded, according to the time set by the

command. The VALIDATION/SLIP light blinks.

VALIDATION/SLIP light.

When using slip paper, detects the slip after the set

(t2)

time enters the slip waiting state. When the slip paper is detected, feeds the slip as far as the print start position, then redetects the slip and waits for the print data. If the slip is not detected after feeding the paper, re-enters the slip waiting state. When using validation paper, detects the paper after the set time detected, re-enters the validation paper waiting state. When the validation paper is detected, waits

for the print data.

If no cut sheet is inserted within the set time

switches from cut sheet mode to paper roll mode

automatically.

mode. Turns off the VALIDATION/SLIP light.

has passed. If the slip is not detected, re-

Operation

(t2)

has passed. If the paper is not

ESC f m

(t-1),

4-8 Reference Information

Notes:

When

printing on a single cut sheet that is narrower carriage movement range, once the printer has been put in the cut sheet mode and the sheet

following operations

supply home command

the

When the

come in contact

jam.

The cut

command.

Use Example Print Control

switch

interface.

the

ASB function to correctly determine

on or

carriage moves away from

sheet

waiting state can be canceled by

should

off,

opening

(ESC <),

with the left

or sending a reset command

for

Cut

of paper has

be avoided: turning

the

cover, issuing

end of

the

Sheet

been inserted,

the home

paper, causing a paper

later in

position, it may

the

this

than

the

power

the

the DLE ENQ

paper state. See section.

the

return

through

Reference Information 4-9

Example print control for cut sheet

1) Enables

2) Enables

3) Receives ASB due to 2).

4) Selects slip printing.

5) Waits for slip paper to be selected. ASB: 4-0*) of the fourth byte of the ASB data. The same rule applies correspondingly to the following:

6) Waits for slip paper to be inserted. ASB: to be “paper p”

7) To cancel the slip paper waiting state, send DLE ENQ 3. When canceled, the printer returns to paper roll mode, and the 4 bytes of are transmitted. ASB: slip paper state

“not selected” (1).

printing

ASB

waits for slip paper selection

to be “selected” (0). *Indicates bit 0

wait for cut sheet sensor (ASB

stop due to slip paper-end.

for all status changes.

(0).

(ASB 4-l)

becomes

(ASB

3-5)

ASB

4-10 Reference Information

8) Waits for the slip to ASB:

waits for the slip paper state

4-l) to be “printable” (0).

9) Transmits each line of print data until there is no data to be transmitted.

In this case, paper has run out. ASB:

slip paper state (ASB “not printable” (1). Advances to step

been sent.

10)

Ejects the slip paper.

ASB

loaded.

is transmitted when the

4-l)

becomes

10)

when all the data has

(ASB

When

printing on a single cut

carriage movement range, once cut

sheet

mode and

following operations

supply

home interface.

When the

come in contact

jam.

2. The command.

Use

Example Print Control for Cut

switch

command

cut

the

ASB function to correctly determine

on or

carriage moves away from

sheet

waiting state can be canceled by

the sheet of

should

off,

opening

(ESC),

with the left

or sending a reset command

sheet that

the

paper

be avoided: turning

the

end of

Sheet

is narrower

printer

has

cover, issuing

the home

the

paper, causing a paper

later in

has

been put in

been inserted,

position, it may

the

this

than the

the

power

the

return through the

the DLE ENQ

paper state. See section.

Transmit Status

Identification

The values of specific bits are fixed in the status information transmitted by the printer, so that the status bytes of commands can be identified. The user can therefore confirm the command to which the status belongs, as

shown in the following table. When using Auto Status Back (ASB), however, process the consecutive three-byte code (except for XOFF) as byte of the

ASB.

Otherwise, the status transmitted by using the command and the status of the second and following bytes of the differentiated.

Command

ESC u ESC v GSI GS r XON <00010001>B XOFF DEL EOT ASB

(1st byte)

ASB (2nd

byte-4th byte)

ASB

data after confirming the first

Status Replay

<O**O****>B <O**O****>B <O**O****>B <O**O****>B

<0001001 <O**l**lO>B <0**

**OO>B

I>B

<O**O****>B

ASB

cannot be

Reference Information 4-11

Notes On Number of Printable Columns

When DIP switch 2-2 is set to ON to increase the number of printable columns, the number of dots and the printable area is as shown below. The OFF setting is shown for comparison.

Number of Horizontal Dots/Character

c*:)

t*c)

DIP switch 2-2 setting

OFF

7 X 9 Font 5 X 9 Font

(*) The 5 X 9 font uses 6 normal dots for one character, but the printer

processes the data as 12 half-dots in the print buffer. Therefore, in this case the printer processes the data as 11 half-dots for one character.

There are restrictions when DIP switch 2-2 is ON, as follows:

1) The printable area for one line is decreased. Setting DIP switch 2-2 to ON increases the number of printable

columns per line but decreases the printable area for one line. Be sure to note the end position of a line and the number of dots for bit-images.

Printable Area/Line

400

385

2) The 10th dot is not printed in the 7

The 7

9 font uses 10 half-dots for one character. However, when

9 font.

DIP switch 2-2 is ON, the printer does not print 10th dot, since the number of printable dots in this setting is 9 and the 10th byte is truncated. Therefore, the 10th dot in some characters is not printed during extended graphic character printing.

This applies to the character for which dots are defined for the 10th byte.

3) The printing results may differ even if the same data is printed. The printer cannot print horizontally adjacent dots. Therefore, the

printing results may differ even if the same character codes are transmitted, since the dots placed on the borderline between characters

2-2

differ depending on the DIP switch

setting. Particularly in line

drawings, a line may be broken when DIP switch 2-2 is ON.

4-12 Reference Information

WEEE (Waste Electrical and Electronic Equipment) Directive

English

The crossed out wheeled bin label that can be found on your product indicates that this product should not be disposed of via the normal household waste stream. To prevent possible harm to the environment or human health please separate this product from other waste streams to ensure that it can be recycled in an environmentally sound manner. For more details on available collection facilities please contact your local government office or the retailer where you purchased this product.

Deutsch

Der Aufkleber mit durchgekreuzter Mülltonne an diesem Produkt weist darauf hin, dass dieses Produkt nicht im normalen Hausmüll entsorgt werden darf. Zur Vermeidung einer möglichen Beeinträchtigung der Umwelt oder der menschlichen Gesundheit und um zu gewährleisten, dass es in einer umweltverträglichen Weise recycelt wird, darf dieses Produkt nicht in den Hausmüll gegeben werden. Informationen zu Entsorgungseinrichtungen erhalten Sie bei der zuständigen Behörde oder dem Geschäft, in dem Sie dieses Produkt erworben haben.

Français

L'étiquette apposée sur ce produit et représentant une poubelle barrée indique que le produit ne peut être mis au rebut avec les déchets domestiques normaux. Afin d'éviter d'éventuels dommages au niveau de l'environnement ou sur la santé, veuillez séparer ce produit des autres déchets de manière à garantir qu'il soit recyclé de manière sûre au niveau environnemental. Pour plus de détails sur les sites de collecte existants, veuillez contacter l'administration locale ou le détaillant auprès duquel vous avez acheté ce produit.

Italiano

L'etichetta con il contenitore barrato applicata sull'imballo indica che il prodotto non deve essere smaltito tramite la procedura normale di smaltimento dei rifiuti domestici. Per evitare eventuali danni all'ambiente e alla salute umana, separare questo prodotto da altri rifiuti domestici in modo che possa essere riciclato in base alle procedure di rispetto dell'ambiente. Per maggiori dettagli sulle strutture di raccolta disponibili, contattare l'ufficio competente del proprio comune o il rivenditore del prodotto.

Español

La etiqueta de un contenedor tachado que hallará en su producto indica que este producto no se puede tirar con la basura doméstica normal. Para impedir posibles daños medioambientales o para la salud, separe este producto de otros canales de desecho para garantizar que se recicle de una forma segura para el medio ambiente. Para más información sobre las instalaciones de recolección disponibles, diríjase a las autoridades locales o al punto de venta donde adquirió este producto.

Português

A etiqueta com o símbolo de um contentor de lixo traçado com uma cruz que aparece no produto indica que este produto não deve ser deitado fora juntamente com o lixo doméstico. Para evitar possíveis danos no ambiente ou na saúde pública, por favor separe este produto de outros lixos; desta forma, terá a certeza de que pode ser reciclado através de métodos não prejudiciais ao ambiente. Para obter mais informações sobre os locais de recolha de lixo disponíveis, contacte a sua junta de freguesia, câmara municipal ou localonde comprou este produto.

Nederlands

Op uw product is een label van een rolcontainer met een kruis erdoor aangebracht. Dit label wil zeggen dat dit product niet bij het normale huishoudelijk afval mag worden ingezameld. Om eventuele schade aan het milieu of de gezondheid van de mens te voorkomen moet dit product gescheiden van al het ander afval worden ingezameld, zodat het op een verantwoorde wijze kan worden verwerkt. Voor meer informatie over uw lokale afvalinzameling wendt u zich tot uw gemeente of de leverancier bij wie u dit product hebt gekocht.

Dansk

Etiketten med et kryds over skraldespanden på hjul, der sidder på produktet, angiver, at dette produkt ikke må bortskaffes sammen med almindeligt husholdningsaffald. For at beskytte miljø og helbred skal dette produkt bortskaffes separat, så det kan genbruges på en måde, der er god for miljøet. Kontakt de lokale myndigheder eller den forhandler, hos hvem du har købt produktet, vedrørende steder, hvor du kan aflevere produktet.

Suomi

Laite on merkitty jäteastia-symbolilla, jonka yli on vedetty rasti. Tämä tarkoittaa, ettei laitetta saa hävittää normaalin talousjätteen mukana. Älä hävitä laitetta normaalin jätteen seassa vaan varmista, että laite kierrätetään ympäristöystävällisellä tavalla, jottei ympäristölle tai ihmisille aiheudu vahinkoa. Lisätietoja kierrätyksestä ja keräyspisteistä saa ottamalla yhteyttä paikallisiin viranomaisiin tai jälleenmyyjään, jolta laite ostettiin.

Svenska

Symbolen med en överkorsad soptunna innebär att denna produkt inte får kastas i vanligt hushållsavfall. För att skydda miljön ska denna produkt inte kastas tillsammans med vanligt hushållsavfall utan lämnas för återvinning på tillbörligt sätt. För mer information om uppsamlingsplatser kontakta din lokala myndighet eller den återförsäljare där du har köpt produkten.

Norsk

Det er krysset over merket av beholderen på hjul som vises på produktet, som angir at dette produktet ikke skal kastes sammen med vanlig husholdningsavfall. Hold dette produktet atskilt fra annet avfall slik at det kan resirkuleres på en miljømessig forsvarlig måte og dermed forhindre eventuell skade på miljø eller helse. Hvis du vil ha mer informasjon om hvor produktet kan leveres inn, kontakter du kommunale myndigheter eller forhandleren der du kjøpte dette produktet.

This information only applies to customers in the European Union, according to Directive 2002/96/EC OF THE EUROPEAN PARLIAMENT AND OF THE COUNCIL OF 27 January 2003 on waste electrical and electronic equipment (WEEE) and legislation transposing and implementing it into the various national legal systems.

For other countries, please contact your local government to investigate the possibility of recycling your product.

Česky

Štítek s přeškrtnutým odpadkovým košem na kolečkách, který lze nalézt na výrobku, označuje, že tento product se nemá likvidovat s běžným domovním odpadem. V zájmu ochrany životního prostředí a lidského zdraví zlikvidujte tento výrobek jako tříděný odpad, který se recykluje způsobem šetrným k životnímu prostředí. Podrobnější informace o sběrných dvorech pro tříděný odpad získáte na obecním úřadě nebo u prodejce, u kterého jste příslušný výrobek zakoupili.

Magyar

A terméken található, áthúzott szemetest ábrázoló címke azt jelzi, hogy ezt a terméket nem szabad a rendes háztartási szeméttel együtt kidobni. Az esetleges környezeti- vagy egészségkárosodást megelõzendõ, kérjük, hogy ezt a terméket a többi szeméttõl elkülönítve helyezze el, és biztosítsa, hogy azt környezetbarát módon újrahasznosítsák. A rendelkezésére álló begyûjtõ létesítményekrõl kérjük tájékozódjon a megfelelõ helyi állami szerveknél vagy a viszonteladónál, ahol a terméket vásárolta.

Polski

Symbol przekreślonego kosza znajdujący się na produkcie oznacza, że nie może on być utylizowany razem z normalnymi odpadami z gospodarstwa domowego. Aby zapobiec potencjalnemu zagrożeniu dla środowiska lub zdrowia ludzkiego, produkt ten należy odseparować od reszty odpadów z gospodarstwa domowego i utylizować w ekologicznie właściwy sposób. Szczegółowe informacje na temat punktów zbiórki odpadów można uzyskać w lokalnych urzędach lub u sprzedawcy danego produktu.

Slovensky

Štítok s preškrtnutým odpadkovým košom na kolieskach, ktorý je možné nájst’ na výrobku, označuje, že tento product sa nemá likvidovat’ s bežným komunálnym odpadom. V záujme ochrany životného prostredia a ľudského zdravia zlikvidujte tento výrobok ako triedený odpad, ktorý sa recykluje spôsobom šetrným k životnému prostrediu. Podrobnejšie informácie o zberných dvoroch pre triedený odpad získate na obecnom úrade alebo u predajcu, u ktorého ste príslušný výrobok zakúpili.

Slovenski

Prečrtan koš za smeti na etiketi, katero lahko najdete na vašem izdelku, pomeni, da tega izdelka ne smete odvreči podobno kot vse ostale smeti. Da bi preprečili morebitne škodljive vplive na okolje ali zdravje, ločite izdelek od vseh ostalih in poskrbite, da bo recikliran na okolju prijazen način. Natančne informacije o tem, kje se nahajajo primerna odlagališča, pridobite v vašem krajevnem uradu ali pri prodajalcu.

Eesti

Teie tootele kleebitud tähis, mis kujutab ratastega prügikonteinerit, millele on rist peale tõmmatud, keelab toote kõrvaldamise majapidamisjäätmetega sarnasel viisil. Keskkonnale või inimeste tervisele tekitatava võimaliku kahju vältimiseks eraldage toode teistest jäätmetest, et tagada selle korduvkasutamine keskkonnasäästlikul viisil. Kui soovite saada rohkem teavet võimalike kogumispunktide kohta, võtke ühendust kohaliku omavalituse ametnikuga või teile toote müünud jaemüüjaga.

Lietuviškai

Užbraukta ratuota šiukšliadėžės etiketė, kurią rasite ant jūsų produkto, reiškia, kad šis produktas neturėtų būti išmestas kartu su įprastinėmis buitinėmis šiukšlėmis. Siekiant išvengti galiamos žalos aplinkai bei žmonių sveikatai, prašome atskirti šį produktą nuo kitų atliekų, ir įsitikinti, kad jis būtų perdirbtas aplinkai nepavojingu būdu. Jei reikia išsamesnės informacijos apie atliekų surinkimo ypatumus, prašome kreiptis į savo vietos valdžios įstaigas arba į mažmeninį pardavėją, iš kurio jūs įsigijote šį produktą.

Latviski

Marķējums ar pārsvītrotu atkritumu tvertni uz ritenīšiem, kas redzams uz izstrādājuma, norāda, ka šo izstrādājumu nedrīkst likvidēt kopā ar parastajiem sadzīves atkritumiem. Lai novērstu iespējamo kaitējumu videi vai cilvēku veselībai, lūdzu, atdaliet šo izstrādājumu no citiem atkritumiem, tādējādi nodrošinot tā otrreizējo pārstrādi videi drošā veidā. Papildinformācijai par pieejamajām atkritumu savākšanas iespējām, lūdzu, sazinieties ar

vietējo pašvaldību vai mazumtirgotāju, no kura jūs iegādājāties šo izstrādājumu.

Ελληνικά

Η διαγραμμένη ετικέτα του τροχοφόρου κάδου απορριμμάτων που θα βρείτε πάνω στο προϊόν σας υποδεικνύει ότι αυτό το προϊόν δεν πρέπει να απορρίπτεται μέσω του κανονικού δικτύου αποκομιδής οικιακών απορριμμάτων. Για να αποτρέψετε πιθανές επιπτώσεις στο περιβάλλον ή την ατομική υγεία, παρακαλούμε να διαχωρίσετε αυτό το προϊόν από άλλα δίκτυα αποκομιδής

ώστε να διασφαλίσετε ότι είναι δυνατή η ανακύκλωσή του με έναν περιβαλλοντικά θεμιτό τρόπο. Για περισσότερες πληροφορίες σχετικά με τις διαθέσιμες δυνατότητες συλλογής απορριμμάτων, παρακαλούμε να επικοινωνήσετε με την τοπική κυβερνητική αρχή ή το κατάστημα λιανικής από όπου αγοράσατε αυτό το προϊόν.

Türkçe

Ürününüzün üzerinde bulunan çarpı işaretli tekerlekli kutu etiketi, bu ürünün normal ev atık sistemi vasıtasıyla elden çıkarılmaması gerektiğini gösterir. Çevreye ve insan sağlığına zarar vermeyi önlemek için, lütfen bu ürünü çevreye zarar vermeyecek şekilde geri dönüşüme tabi tutulmak üzere diğer atıklardan ayırın. Mevcut toplama tesisleri ile ilgili ayrıntılı bilgi edinmek için, yerel devlet makamlarıyla veya bu ürünü satın aldığınız satıcıyla irtibata geçin.

Română

Eticheta arătând un coş de gunoi tăiat cu două linii încrucişate, care poate fi găsită pe produs, indică faptul că acesta nu trebuie aruncat la gunoi laolaltă cu gunoiul menajer. Pentru a evita posibila degradare a mediului înconjurător sau a sănătăţii umane, colectaţi separat acest produs de gunoiul menajer pentru a vă asigura că poate fi reciclat într-un mod ecologic. Pentru mai multe detalii privind punctele disponibile de colectare, contactaţi autorităţile locale sau comerciantul de la care aţi achiziţionat acest produs.

Български

Етикетът, представляващ зачертано кошче за боклук в кръг, който можете да видите върху вашия продукт, означава, че този продукт не трябва да се изхвърля заедно с обикновените домакински отпадъци. За предпазване от евентуални щети върху околната среда или човешкото здраве, моля, отделете този продукт от останалите отпадъци, за да се гарантира

, че той ще бъде рециклиран по екологично съобразен начин. За повече информация относно наличните места за събиране на отпадъци, моля, свържете се с местните власти или търговеца, от когото сте закупили този продукт.

Printed in Japan

Epson U375 - TM B/W Dot-matrix, TM-U375P Printer User Manual

Specifications and Main Features

Frequently Asked Questions

User Manual