Epson S5U13U11 User Manual

S1D13U11 Display Controller

S5U13U1 1 Evaluation Board

User Manual

SEIKO EPSON CORPORATION Rev. 1.1

Evaluation board/kit an d Devel op ment too l imp or t a nt noti ce

1. This evaluation board/kit or development tool is designed for use for engineering evaluation, demonstration, or develop­ment purposes only. D o n ot us e i t for other purpose. It is not int end ed t o meet the requirement of design for finished prod­uct.

2. This evaluation board/kit or development tool is intended for use by an electronics engineer, and it is not the product for
consumer. The user should use this goods properly and safely. Seiko Epson dose not assume any responsibility and liabil­ity of any kind of damage and/or fire coursed by usage of it. User should cease to use it when any abnormal issue occurs
even during proper and safe use.

3. The part used for this evaluation board/kit or development tool is changed without any notice.

NOTICE

No part of this material may be reproduced or duplicated in any form or by any means without the written permission of Seiko
Epson. Seiko Epson reserves the right to make changes to this material without notice. Seiko Epson does not assume any lia­bility of any kind arising out of any inaccuracies contained in this material or due to its application or use in any product or cir­cuit and, further, there is no representation that this material is app licable to produc ts requiring high level reliability, such as,
medical products. Moreover, no license to any intellectual property rights is granted by implication or otherwise, and there is
no representation or warranty that anything made in accordance with this material will be free from any patent or copyright
infringement of a third party. This material or portions thereof may contain technology or the subject relating to strategic
products under the control of the Foreign Exchange and Foreign Trade Law of Japan and may require an export license from
the Ministry of International Trade and Industry or other approval from another government agency.

All brands or product names mentioned herein are trademarks and/or registered trademarks of their respective companies

©SEIKO EPSON CORPORATION 2011, All rights reserved.

S1D13U11 Display Controller

Table of Contents

Chapter 1 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

Chapter 2 Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

Chapter 3 Installation and Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . 7

3.1 Configuration Jumpers . . . . . . . . . . . . . . . . . . . . . . . . . . . .7

Chapter 4 Technical Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

4.1 Power . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

4.1.1 Power Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

4.1.2 Voltage Regulators . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

4.1.3 LED Backlight Voltage Regulators . . . . . . . . . . . . . . . . . . . . . . . . . . 12

4.1.4 LED Backlight Power Circuit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

4.2 Clock . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

4.3 Reset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

4.4 Wake-up Key . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

4.5 Buzzer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

4.6 Touch Screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

4.7 Serial Flash ROM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

4.8 Host CPU Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

4.9 Generic LCD Panel Interface . . . . . . . . . . . . . . . . . . . . . . . . 15

4.10 Ortustech LCD Panel Interface . . . . . . . . . . . . . . . . . . . . . . . . 15

4.11 Peripheral Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

Chapter 5 Parts Lists . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

Chapter 6 Schematic Diagrams . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20

Chapter 7 Board Layout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24

7.1 Peripheral Expansion Board . . . . . . . . . . . . . . . . . . . . . . . . . 25

Chapter 8 References . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26

8.1 Documents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26

8.2 Document Sources . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26

Chapter 9 Change Record . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27

S5U13U11 Evaluation Board User Manual (Rev. 1.1) EPSON 3

S1D13U11 Display Controller

4 EPSON S5U13U11 Evaluation Board User Manual (Rev. 1.1)

S1D13U11 Display Controller

Chapter 1 Introduction

This manual describes the setup and operation of the S5U13U11 Evaluation Board. This evaluation board is
designed as an evaluation platform for the S1D13U11 Display Controller.

The S5U13U11 evaluation board can connect to a variety of embedded CPU boards and a personal computer via
USB 2.0. This evaluation board includes a touch screen controller, serial flash ROM and buzzer. This evaluation
board can connect to exte rnal devices such as LCD panel wi th touch scre en, key matrix ci rcuit, and ex pansion seri al
devices via connector.

This user manual is updated as appropriate. Please check the Epson Research and Development Website at
www.erd.epson.com for the latest revision of this document before beginning any development.

We appreciate your comments on our docu mentation. Please conta ct us via email at documentatio [e-mail].

This manual applies to the following evaluation boards.

• S5U13U11P00C100 (no LCD panel)

• S5U13U11P10C100 (with LCD panel)

S5U13U11 Evaluation Board User Manual (Rev. 1.1) EPSON 5

S1D13U11 Display Controller

Chapter 2 Features

The S5U13U11 Evaluation Board includes the following features:

• S1D13U11 Display Controller (144-pin QFP)

• Integrated Silicon Solution, Inc. IS42S16800E-7TLI 128M-bit SDRAM (54-pin TSOP)

• USB mini B connector for S1D13U11 USB2.0 High-speed device port

• Headers for S1D13U11 LCD interface pins

• Built-in Ortustech TFT panel with touch screen (S5U13U11P10C100 only)

• Header for S1D13U11 GPIO, SPI and I2C pins (need to add the connector)

• Resistive type touch screen controller with SPI interface

• 1Mbit serial flash ROM with SPI interface (for configuration data storage)

• Buzzer and Wake-up key

• 24MHz oscillator

• VBUS 5V power input or external DC5V power input can be selected

• Voltage regulator with 1.8V and 3.3V

• Voltage regulator with adjustable 6~24V output, 40mA max., to provide power for LED backlight of LCD
panels.

• LED backlight circuit with PWM control

6 EPSON S5U13U11 Evaluation Board User Manual (Rev. 1.1)

S1D13U11 Display Controller

Chapter 3 Installation and Configuration

The S5U13U11 evaluation b oard in corpor ates jumpers an d 0 ohm resi stors which a llow it to be used in a varie ty of
different configurations.

3.1 Configuration Jumpers

The S5U13U11 has 15 jumpers which conf igure vario us board setti ngs. The j umper pos itio ns for e ach fun ction a re
shown below. JP5, JP6, JP7, JP8, JP9, JP10, JP11, JP14 and JP15 are solder bridges to reduce power noise. To
change the jumper position remove the sold er .

Jumper Function Position 1-2 Position 2-3 No Jumper

JP1 Board current measurement Normal — Current measurement
JP2 Board powe r supply VBUS 5V input External DC5V —
JP3 VBUS input signal VBUS 5V input External DC5V —
JP4 Power-on reset source VBUS 5V input External DC5V —
JP5 COREVDD current measurement Normal — Current measurement
JP6 PLLVDD current measurement Normal — Current measurement
JP7 PIOVDD current measurement Normal — Current measurement
JP8 USBVDD current measurement Normal — Current measurement

JP9 MIO VDD cur r ent meas urem en t Normal — Current measurement
JP10 Touch screen power 5V 3.3V (Position 1-3) —
JP11 External 3.3V current measurement Normal — Current measurement
JP12 LED Backlight 12V power control ON — OFF
JP13 Ortustech panel control ON/OFF control Always ON —
JP14 3.3V regulator current measurement Normal — Current measurement
JP15 1.8V regulator current measurement Normal — Current measurement

= Default setting

JP1 - Current Measurement of the S5U13U11 Evaluation Board

JP1 can be used to measure the current consumption of the S5U13U11 power supply.
When the jumper is at position 1-2, normal operation is selected.
When no jumper is installed, the current consumption for power sup ply can be measured by co nnecting an ammeter
between pins 1 and 2 of the jumper.

S5U13U11 Evaluation Board User Manual (Rev. 1.1) EPSON 7

S1D13U11 Display Controller

JP2 - Power Supply Select for the S5U13U11 Evaluation Board

JP2 can be used to select the S5U13U11 power supply.
When the jumper is at position 1-2, VBUS 5V input is selected. The external power supply is not needed.
When the jumper is at position 2-3, external DC5V input is selected. The external power supply is needed.

The supply current of VBUS is specified as a maximum 500mA in the USB specification.

JP3 - VBUS Input Signal Select

JP3 can be used to select the signal of the S1U13U11 VBUS input pin.
When the jumper is at position 1-2, VBUS input is selected.
When the jumper is at position 2-3, external DC5V input is selected.

JP4 - Power-on Reset Source Select

JP4 can be used to select the source of the power-on reset circuit.
When the jumper is at position 1-2, VBUS input is selected.
When the jumper is at position 2-3, external DC5V input is selected.

Figure 3-1: Configuration Jumper Locations (JP1, JP2, JP3, JP4)

8 EPSON S5U13U11 Evaluation Board User Manual (Rev. 1.1)

S1D13U11 Display Controller

JP5, JP6, JP7, JP8, JP9 - Current Measurement of the S1D13U11 Power Su pplies

JP5, JP6, JP7, JP8, JP9 can be used to measure the current consumption of the S1D13U11 power supplies.
When the jumper is at position 1-2, normal operation is selected.
When no jumper is installed, the current consumption for each power supplies can be measured by connecting an
ammeter between pins 1 and 2 of the jumper.

The jumper associated with each power supply is as follows:

JP5 for COREVDD
JP6 for PLLVDD
JP7 for PIOVDD
JP8 for USBVDD
JP9 for MIOVDD

Figure 3-2: Configuration Jumper Locations (JP5, JP6, JP7, JP8, JP9)

S5U13U11 Evaluation Board User Manual (Rev. 1.1) EPSON 9

S1D13U11 Display Controller

JP11, JP14, JP15 - Current Measurement of the On-board Power Supplies

JP11, JP14, JP15 can be used to measure the current consumption of on-board power supplies.
When the jumper is at position 1-2, normal operation is selected.
When no jumper is installed, the current consumption for each power supplies can be measured by connecting an
ammeter between pins 1 and 2 of the jumper.

The jumper associated with each power supply is as follows:

JP11 for external 3.3V power
JP14 for 3.3V regulator
JP15 for 1.8V regulator

Figure 3-3: Configuration Jumper Locations (JP11, JP14, JP15)

10 EPSON S5U13U11 Evaluation Board User Manual (Rev. 1.1)

S1D13U11 Display Controller

JP10 - Touch Screen Power Select

JP10 can be used to select the power of the touch screen.
When the jumper is at position 1-3, the power of touch screen signals (X+, Y+) is selected 3.3V.
When the jumper is at position 1-2, the power of touch screen signals (X+, Y+) is selected 5V.

JP12 - LED Backlight 12V Power Control

JP12 can be used to control the LED backlight 12V power.
When the jumper is at position 1-2, the 12V power is always on.
When no jumper is installed, the 12V power is always off.

JP13 - Ortustech Panel Power Control

JP13 can be used to control Ortustech panel power (S5U13U11P10C100 only).
When the jumper is at position 1-2, the GPO7 pin of the S1D13U11 can be used to control the Ortustech panel
power.
When the jumper is at position 2-3, the Ortustech panel power is always on.

Figure 3-4: Configuration Jumper Locations (JP10, JP12, JP13)

S5U13U11 Evaluation Board User Manual (Rev. 1.1) EPSON 11

S1D13U11 Display Controller

Chapter 4 Technical Description

4.1 Power

4.1.1 Power Requirements

The S5U13U11 evaluation board operates only by the USB bus power (VBUS 5V) of the USB cable. When the
current supply of VBUS 5 V is ne eded the p ower con sumptio n over 500mA, the exter nal DC5V p ower sup ply must
be selected. Because the current supply of VBUS 5V is specified max 500mA in the USB specification.

When the external DC5V power is selected, JP2 and JP4 should be switched jumper position 2-3 and the DC5V
power is supplied through the CN3 header.

4.1.2 Voltage Regulators

The S5U13U11 evaluation board has an on-board linear regulator (IC6, IC7) to provide the 1.8V and 3.3V power
required by the S1D13U11 Display Controller.

4.1.3 LED Backlight Voltage Regulators

The S5U13U11 evaluation board has an on-board switching voltage regul at or (IC8) to generate adjustable 6~ 24V,
which can be used to 12V power the LED backlight on some LCD panels. When the 12V power is used, the JP12
jumper must be selected position 1-2.

4.1.4 LED Backlight Power Circuit

The S5U13U11 evaluation board has an on-board LED backlight power circuits (IC9, IC10). The luminous of the
LED backlight can be controlled by the S1D13U11 PWM. The LED backlight power is output through the CN7
header.

4.2 Clock

The S5U13U11 evaluation board is operated by the on-board 24MHz oscillator (CR1).

4.3 Reset

The S5U13U11 evaluation board can be reset using a push-button (SW1), or on-board power-on reset circuit. The
power-on reset circu it is designed the target speci fication which the threshol d voltage is typ 2.7V and the rising del ay
time is typ 10ms.

12 EPSON S5U13U11 Evaluation Board User Manual (Rev. 1.1)

S1D13U11 Display Controller

4.4 Wake-up Key

The S5U13U11 evaluation boar d has a wake-up key (SW2) which is used to retur n f ro m sl eep mode . The wake-up
key is connected to the S1D13U11 INT1 pin.

4.5 Buzzer

The S5U13U11 evaluation board has a buz zer (BZ1) which is used fo r the b eep so und. The buz zer is connected to
the S1D13U11 BUZZER pin.

4.6 Touch Screen

The S5U13U11 evaluation board has a resistive type touch screen controller (IC3). Chip select pin (S1D13U11
SS0#) and interrupt pin (S1D13U11 INT0) are connected to the LED3 and LED4.

The analog signals (X+, X-, Y+, Y-) of the touch screen controller are connected to the CN6 header.

4.7 Serial Flash ROM

The S5U13U11 evaluation board has a serial flash ROM (IC4) which is stored the configuration data and start-up
display data.

Figure 4-1: Reset Switch and Wake-up Key Locations (SW1, SW2)

S5U13U11 Evaluation Board User Manual (Rev. 1.1) EPSON 13

S1D13U11 Display Controller

4.8 Host CPU Interface

The S1D13U11 host interface (USB2.0 High-speed device port) is available on connector CN1 which allows the
S5U13U11 evaluation board to be connected to a variety of development platforms.

The LED1 turns on when VBUS power is supplied.

Figure 4-2: USB Connector and LED1 Locations (CN1, LED1)

14 EPSON S5U13U11 Evaluation Board User Manual (Rev. 1.1)

S1D13U11 Display Controller

4.9 Generic LCD Panel Interface

The S1D13U11 LCD interface signals are available on connectors CN10 and CN11.

Both connector are 0.1x0.1 inch 40-pin header (20x2). For the pinout of connectors CN10 and CN11, see Chapter
6, “Schematic Diagrams” on page 20.

On the evaluation board there is an adjustable 6~24V, 40mA max. power supply. This voltage is provided only on
connector CN10 (it is n ot us ed elsewhere on the board). It is intended for use to power the LED backlight on some
LCD panels. The voltage is adjusted by the VR2 pot.

For LCD panels that use a CCFL backlight, an ext ernal power su pply must be used to provi de power to the in verter
for the CCFL backlight. Usually, the inverter current consumption is higher than the maximum 40mA current
available from the on-board voltage regulator.

4.10 Ortustech LCD Panel Interface

The S1D13U11 LCD interface signals are connected to the Ortustech LCD panel (COM41T4M17XTC) by
connectors CN10 and CN11 (S5U13U11P10C100 only).

Figure 4-3: LCD Panel Connector Locations (CN8, CN9, CN10, CN11)

S5U13U11 Evaluation Board User Manual (Rev. 1.1) EPSON 15

S1D13U11 Display Controller

4.11 Peripheral Interface

The S1D13U11 peripheral interf ace signa ls are avai lable on connec tor CN4. Connector CN4 i s 0.1x0.1 inch 40 -pin
header (20x2). For the pinout of connectors CN4, see

The S5U13U11P00C100 evaluation boa rd has a SPI interface, I2 C interface, GPIO interfac e and Key-scan interfac e.

Chapter 6, “Schematic Diagrams” on page 20.

Figure 4-4: Peripheral Connector Location (CN4 : no assembly)

16 EPSON S5U13U11 Evaluation Board User Manual (Rev. 1.1)

S1D13U11 Display Controller

Chapter 5 Parts Lists

Table 5-1: Parts Lists

Quantity Value Reference Part Manufacturer

1 - BZ1 PKLCS1212E2000-R1 Murata
6 1u C1,C21,C64*,C80*,C81*,C87** GRM188F11C105ZA01 Murata
1 2200p C2 UMK107B222KZ Taiyo Yuden

C3,C8,C11,C13,C16,C18,C20,C24,

25 0.01u

1 1000p C5 GRM188B11H102KA01 Murata
2 9p C9,C14 UMK107CH090DZ Taiyo Yuden

23 0.1u

4 10u C6,C45,C83,C84 GRM21BB10J106ME01 Murata
4 10uZ-C C62,C68,C71,C73 EMK325F106ZH Taiyo Yuden
2 2.2u C63*,C65* GRM21BF11E225ZA01 Murata
2 4.7u C66,C67* GRM31MF11C475ZA12B Murata
5 2.2u C70*,C72*,C74*,C76*,C77* GRM188B31A225KE33 Murata
3 10u C69*,C75*,C78* C3225JB1A106M TDK
1 10p C79 GRM1882C1H100JA01 Murata
1 1u C82 GRM32RB11H105KA01B Murata

9 0.1u
1 - CN1 54819-0572 MOLEX

1 - CN2** A2-4PA-2.54DS(71) Hirose
1 - CN4** PS-40SD-D4T1-1 JAE
3 - CN3,CN5**,JP12 WL-1-2 Mac8
2 - CN6,CN7 WL-1-4 Mac8
1 - CN8* 59453-041110EALF FCI
1 - CN9* 046281267202846+ Kyocera Elco
2 - CN10,CN11 HIF3FC-40PA-2.54DSA(71) Hirose
1 - CR1 FA-238 (24MHz) EPSON_QD
1 - D1 MBR0530 Fairchild
2 - D2,D3 1SS421 Toshiba
1 - DM1 DF3A6.8FU Toshiba
1 - DM2 HRW0202B Renesas
2 - FLS1,FLS2 ACF451832-222 TDK
1 - IC1 S-80927CNNB SII
1 - IC2 S1D13U11 EPSON
1 - IC3 TSC2046IPW TI

C26,C28,C30,C33,C35,C38,C40,
C42,C44,C48,C50,C51,C53,C55,
C57,C59,C61

C7,C10,C12,C15,C17,C19,C22,C25,
C27,C29,C32,C34,C37,C39,C41,
C43,C47,C49,C52,C54,C56,C58,C60

C4,C23,C31,C36,C46,C85,C86,C88,
C89

GRM155B11E103KA Murata

GRM155B31C104K Murata

GRM188R11H104JA01 Murata

S5U13U11 Evaluation Board User Manual (Rev. 1.1) EPSON 17

S1D13U11 Display Controller

Table 5-1: Parts Lists

Quantity Value Reference Part Manufacturer

1 - IC4 LE25FU106BMA Sanyo
1 - IC5 IS42S16800E ISSI
1 - IC6 R1170H331B RICOH
1 - IC7 R1170H181B RICOH
1 - IC8 TPS61040DBVR TI
2 - IC9,IC10 TPS61042DRB TI
2 - IC11,IC12 TC7SZ04F Toshiba
1 - JP1 A2-3PA-2.54DS(71) Hirose
4 - JP2,JP3,JP4,JP13* WL-1-3 Mac8
4 60 L1,L2,L4,L5 BLM21PG600SN1 Murata
1 90 L3** DLW21SN900SQ2L Murata
1 10uH L6 LQH32CN100K23 Murata
2 4.7uH L7,L8 LQH32CN4R7M23L Murata
4 - LED1,LED2*,LED3,LED4 SML-310MTT86 ROHM
1 uctor QF1* NTF3055L108 OnSemicond
1 33 R1 MCR03EZHJ330 ROHM
1 820 R2 MCR03EZHJ821 ROHM
1 10 R3 MCR03EZHJ100 ROHM
1 6.2k R11 RR0816P-622-D SSM
3 1k R20,R77,R87* MCR03EZHJ102 ROHM
1 1.8k R26 MCR03EZHJ182 ROHM
2 2.2k R36,R37 MCR03EZHJ222 ROHM

R5**,R6,R7,R8,R9,R10,R12,R13,
R14,R15,R16**,R17,R18,R19,R21,
R22,R23,R24,R25,R27,R28,R29,
R30,R31,R32,R33,R34,R35,R38,
R39,R40,R41,R42,R43,R44,R45,
R46,R47,R48,R49,R50,R51,R52,
R53,R54,R55,R56,R57,R58,R59,

100 0

1 20k R83* RR0816P-203-D SSM
1 100 R85* MCR03EZHJ101 ROHM
1 6.8k R86* RR0816P-682-D SSM
2 10k R89**,R115** MCR03EZHJ103 ROHM
1 820k R90 MCR03EZHJ824 ROHM
1 68k R91 RR0816P-683-D SSM

R60,R61,R62,R63,R64,R65,R66,
R67,R68,R69,R70,R71,R72,R73,
R74,R75,R76,R78,R79,R80,R81,
R82,R84,R93,R94**,R96*,R97**,
R98**,R99**,R100**,R101**,R102**,
R105*,R106*,R107*,R108*,R109*,
R110*,R111,R114*,R117**,R118**,
R119**,R120**,R121,R122,R123**,
R124**,R125**,R126

MCR03EZHJ000 ROHM

18 EPSON S5U13U11 Evaluation Board User Manual (Rev. 1.1)

S1D13U11 Display Controller

Table 5-1: Parts Lists

Quantity Value Reference Part Manufacturer

1 47k R92 MCR03EZHJ473 ROHM
1 22k R95 MCR03EZHJ223 ROHM
2 12 R103,R104 MCR03EZHJ120 ROHM
4 100k R4,R112**,R113**,R116** MCR03EZHJ104 ROHM
3 220 R88*,R127,R128 MCR03EZHJ221 ROHM
1 - SW1 SKRPACE010 ALPS
1 - SW2 SKHLLB ALPS
3 - TP47,TP48,TP49 LC-33-S-Red Mac8
4 - TP51,TP52,TP56,TP58 ST-1-2 Mac8

8 ­1 10k VR1* RJ-5W103 Copal

1 200k VR2 SM-42X(204) Copal
2 - ZD1**,ZD2** AVRL161A6R8G TDK
1 - LCD panel* COM41T4M17XTC Ortustech

TP1,TP2,TP3,TP9,TP10,TP50,
TP60**,TP61

LC-33-S-Yellow Mac8

* not populated on S5U13U11P00C100
** not populated on S5U13U11P00C100 and S5U13U11P10C100.

S5U13U11 Evaluation Board User Manual (Rev. 1.1) EPSON 19

S1D13U11 Display Controller

Chapter 6 Schematic Di agrams

Figure 6-1: S5U13U11P00C100 Schematic Diagram (1 of 2)

20 EPSON S5U13U11 Evaluation Board User Manual (Rev. 1.1)

S1D13U11 Display Controller

Figure 6-2: S5U13U11P00C100 Schematic Diagram (2 of 2)

S5U13U11 Evaluation Board User Manual (Rev. 1.1) EPSON 21

S1D13U11 Display Controller

2009/7/24

Figure 6-3: S5U13U11P10C100 Schematic Diagram (1 of 2)

22 EPSON S5U13U11 Evaluation Board User Manual (Rev. 1.1)

2009/7/24

The following “JP” is the

appended goods treatments

When you inversely

arrange the panel

(Back mounting)

(Back mounting)

“L” FET=ON

PANEL POWER

1-2:CONTROLLED

2-3:FORCED OFF

P-ch FET

2SJ612

S1D13U11 Display Controller

Figure 6-4: S5U13U11P10C100 Schematic Diagram (2 of 2)

S5U13U11 Evaluation Board User Manual (Rev. 1.1) EPSON 23

S1D13U11 Display Controller

Chapter 7 Board Layout

Figure 7-1: Board Layout (Top View)

24 EPSON S5U13U11 Evaluation Board User Manual (Rev. 1.1)

S1D13U11 Display Controller

S5U13U11

CN4

Expansion Peripheral Board

PS-40PE-D4LT1-PN1

2mm

7.1 Peripheral Expansion Board

If a peripheral expans ion board is requir ed for developement, as semble connector CN4 on th e S5U13U11 evaluation
board. The mating connector to CN4 is PS-40PE-D4LT1-PN1 (Japan Aviation Electronics Industry, Limited).
Assemble the PS-40PE-D4LT1-PN1 connector with 2mm of clearance from the PCB edge to the mold edge.

Figure 7-2: Peripheral Expansion Board Connection

S5U13U11 Evaluation Board User Manual (Rev. 1.1) EPSON 25

S1D13U11 Display Controller

Chapter 8 References

8.1 Documents

• Epson Research and Development, Inc., S1D13U11 Hardware Functional Specification, document number
X96A-A-001-xx

• Epson Research and Development, Inc., S1D13U11 Software Functional Specification, document number
X96A-A-002-xx

8.2 Document Sources

• Epson Research and Development Website: http://www.erd.epson.com

26 EPSON S5U13U11 Evaluation Board User Manual (Rev. 1.1)

Chapter 9 Change Record

X96A-G-001-01 Revision 1.1 - Issued: April 21, 2011

• globally replace “Casio” with “Ortustech”

• add Evaluation board/kit and Development tool important notice above Copyright notice

• chapter 6 Schematic Diagrams - add S5U13U11P10C100 Schematic Diagrams

X96A-G-001-01 Revision 1.0 - Issued: September 9, 2009

• Iniatial release

S1D13U11 Display Controller

S5U13U11 Evaluation Board User Manual (Rev. 1.1) EPSON 27

International Sales Operations

AMERICA

EPSON ELECTRO NICS AMERICA, IN C .

2580 Orchard Parkway
San Jose, CA 95131,USA
Phone: [phone] FAX: [phone]

EUROPE

EPSON EUROPE ELECTRONICS Gmb H

Riesstrasse 15, 80992 Munich,
GERMANY
Phone: [phone] FAX: [phone]

ASIA

EPSON (CHINA) CO., LTD.

7F, Jinbao Bldg., No.89 Jinbao St.,
Dongcheng District,
Beijing 100005, CHINA
Phone: [phone] FAX: [phone]

SHANGHAI BRANCH

7F, Block B, High-Tech Bldg., 900, Yishan Road,
Shanghai 200233, CHI NA
Phone: [phone] FAX: [phone]

SHENZHEN BRANCH

12F, Dawning Mansion, Keji South 12th Road,
Hi-Tech Park, Shenzhen 518057, CHINA
Phone: [phone] FAX: [phone]

EPSON HONG KONG LTD .

Unit 715-723, 7/F Trade Square, 681 Cheung Sha Wan Road,
Kowloon, Hong Kong
Phone: [phone] FAX: [phone]

EPSON TAIWAN TECHNOLOGY & TRADING LTD.

14F, No. 7, Song Ren Road,
Taipei 110, TAIWAN
Phone: [phone] FAX: [phone]

EPSON SINGAPO RE PTE., LTD.

1 HarbourFront Place,
#03-02 HarbourFront Tower One, Singapore 098633
Phone: [phone] FAX: [phone]

SEIKO EPSON CORP.
KOREA OFFICE

5F, KLI 63 Bldg., 60 Yoido-dong
Youngdeungpo-K u, Seoul , 150 -7 63, KO RE A
Phone: [phone] FAX: [phone]

SEIKO EPSON CORP.
MICRODEVICES OPERATIONS DIVISION

Device Sales & Marketing Dept.

421-8, Hino, Hino-shi, Tokyo 191-8501, JAPAN
Phone: [phone] FAX: [phone]

Document Code: X96A-G-001-01

Issued 2011/04/21

Authorized Distribution Brand：

Website：

Welcome to visit www.ameya360.com

Contact Us：

Address：

401 Building No.5, JiuGe Business Center, Lane 2301, Yishan Rd

Minhang District, Shanghai , China

Sales：

Direct [phone]

Email [e-mail]

QQ 800077892

Skype ameyasales1 ameyasales2

Customer Service：

Email [e-mail]

Partnership：

Tel [phone]-8333

Email [e-mail]