Continuous Ink Supply System
for
Epson Stylus Photo R200/R210/R300/R310
Installation Instruction
For ST Prefilled Version
With Auto Reset Chips
This Version of the Continuous Ink Flow System comes with Prefilled Cartridges and
Auto Reset Chips. You just need to fill the Reservoir bottles and print! The whole
operation is very easy. It’s really an effective tool to save your money.
CIS for EPSON stylus R200/R210/R300/R310 Instruction
Thank you for purchasing ST Continuous Ink Supply System. We appreciate
your support and will try our best to make your experience with our products a
pleasant one. Printing has been a different experience ever since you installed
ST Continuous Ink Supply system on your own printer. Just imagining being
able to print without regard to the ink level in those expensive little cartridges.
Please take your time installing ST Continuous Ink Supply system. Do not
remove your old cartridge until you have the ST CIS system primed and ready to
install (to prevent the drying of heads). In addition, make sure you are getting
perfect nozzle checks before installing the ST CIS system. The ST CIS system
won’t be able to work properly if the nozzles are previously clogged.
Most people get a perfect nozzle check the first time after installing the ST
Continuous Ink Supply system; others may need to run two or three cleaning
cycles or let the printer sit for a while before they get the perfect results.
1、General Guide:
1) Components
A、CIS system 1 set B、 Air filters 6pcs C、Support Arm 1 set
D、Refill Kit 6pcs E、Instruction CD 1pc
2) Opening box inspection
a、Check whether all the accessories are ready.
b、Check whether there's the leakage of the CISS, whether some tubes have been
separated from the CISS, whether there are air bubbles in the tube (If there exists more
than 20CM air space, please kindly to contact with the local dealer)
2、Printer testing:
1) Check whether the printer is in normal condition, like mechanical status, lubrication
status etc.
2) Print testing lines to ensure the printing head is good condition.
3) Print pictures to see whether the printing image is ok.
3、Installation Procedures:
1) First step
Put the CISS on the left side Pull out the small rubber plug Place 4pcs of air filters into
of the printer. In the meantime from the air hole as above air holes, the thicker side
place all the tubes at correct picture shown. is down into tank.
position.
2）Second step: Remove cartridge
Press the ink cartridge replace Move the cartridge-car to the cartridge Unplug the power
button replace position
3) Third step: Set up the Continuous Ink Supply System
Replace the spring of the open the cover of cartridge to some Insert screwdriver into the place
cartridge-car degree angle that joint cover and cartridge-car
Circumgyrate screwdreiver Separate the right side of Take off the cover of cartridge-car
deasilly cartridge-car
4) Fourth step: Set up the Continuous Ink Supply System
Remove original cartridge Insert our no-sponge cartridge Close the cover for cartridge
into printer carefully
5) Fiveth step: Fix Support Arm
Tear off the sticker Fix the arm on the 25cm right far from Tear off the sticker
you printer
Fix the balance arm Tear off the sticker of clamp Attached the clamp on your printer
and let it parallel with printer
6) Sixth step : Install tubeline
Insert tubelline through the arm Finished
7) Seventh Step: Adjust the tubeline
Adjust the tubeline,remove the Make sure tubline will not meet Make sure the lengh of tubline is
Cartridge-car back and forth printer when printing enough to reach the far left and right
Too long twist Perfect
8) Eighth step
Instert the plug Turn on the power switch check
wether all thing is usual
9)Nineth step: Nozzle check
Usual
Broken line
进入打印机喷嘴检查选项
The nozzle check patterns are in broken-line, mostly because of small dusk entered into the nozzle, after
repeated cleaning, if there is still a few broken line, pls let the printer don’t work about 1 hour, then print
the nozzle check pattern, maybe it works well.
4、Reset Procedure:
If the indicator light flashing when printing, it tells that you need to reset the chip to full
status. Please turn off your printer for about 30 seconds and switch it back on. Ink meter bar
shall show full ink. You can start printing as usual.
5、Refill Ink:
Please pay attention to the ink level in the reservoirs; if the ink level is below 1CM as the
above picture shown, please use refill kits to fill ink into Reservoir bottles. Carefully pull out
the rubber plugs from the refill holes.(there is possibility of ink spattering. Be careful!) Refill
ink according to the color in short supply. Then put the rubber back. (Please keep the printer
and the reservoir at the same horizontal line during the process of refilling ink.)
6. How to install the cover of cartridge:
Pls first install the left side of Then install the other side Adjust well the joint position
the cover into cartridge-car
Press the right side of cover Finished
to make it install well
7、Attention for maintenance:
Take out the CISS including the inner cartridges and other components. Then
remove support arm from printer, and place the original cartridges in. Please
inquire local dealer before sending to maintenance.
Notice:
1. Please don’t take out cartridge at random after installing the CIS system.
Keep the reservoir bottles on the same level with the printer.
2. Try to keep at least 1/2 inch of ink in the bottles, as you don’t want to run out
of ink and draw air into the cartridge.
3. Don’t place the Reservoir Bottles higher or lower much than the printer.
4. To be used in a dry place between 15 and 35 degree. Avoid exposure to direct
sunlight.
5. Don’t put the continuous ink supply systems reversed or leaning during the
shipment. Please make sure all the ink filling holes and Ventilation holes are
closed tightly during the transportation. Otherwise, the ink shall leak out.
6. Don’t sway the cartridge frequently. It may cause ink leakage.
7. Don’t pull out the connector of cartridge and don’t tear off adhesive tape at the
bottom of cartridge.
Warning:
1. Not drinkable; keep it out reach of children.
2. Avoid exposure to direct sunshine and don’t keep it in high or freezing
temperature.
3. Avoid collision and fallen down.
Loading...