Epson LABELWORKS PX LW-PX750 User Manual
1
2
3
LABELWORKS PX
LW-PX750
Included Items
User’s Guide
Ver.01
Read this document carefully to use this product
safely and correctly. If your product is faulty, please
read the included warranty card and contact the
store you purchased it from. If you require further
assistance, contact your local K-Sun customer
support center.
Please also visit us at http://labelworks.epson.com
for help and support. You can download the latest
version of this User’s Guide from the website.
International ENERGY STAR® Compliance
Statement
The purpose of the International ENERGY STAR®
Program is to promote the development and
popularization of energy-ecient oce equipment.
As an ENERGY STAR® Partner; Seiko Epson
Corporation has determined that this product meets
the ENERGY STAR® guidelines for energy eciency.
Notation used in this manual
Handling the product improperly by ignoring
DANGER
WARNING
CAUTION
Attention
MEMO
, , ,
, ,
this symbol can result in immediate danger of
death or serious injury.
Handling the product improperly by ignoring
this symbol can lead to death or serious
injur y.
Handling the product improperly by ignoring
this symbol can lead to injury and property
damage.
Important information.
Supplementary note
Reference page in this manual.
Example of label artwork.
Buttons on the product.
456
The included items dier depending on the type of product package you purchased. Use the following table to check the items.
If you would like to purchase an item that is not included or have purchased a package other than one in the following table, see
the separate sheet included with the product.
No. Included item name
LW-PX750 Full kit LW-PX750 Lite kit
Package name
1 LW-PX750
2 AC adapter
3 PX tape cartridge
4 USB cable -
5 Label Editor Professional CD-ROM
-
6 Documents *
* You can download LW-PX750 User's Guide (PDF version) from http://labelworks.epson.com.
Specications
Body
Dimensions Approx. 193 (W) x 238 (D) x 66 (H) (mm)
Weight
Approx. 1,015 g (excluding batteries, tape cartridge)
Usage conditions
Operating temperature 5 to 35 degrees C
Storage temperature -10 to 55 degrees C
Supported tape width
4 mm, 6 mm, 9 mm, 12 mm, 18 mm, 24 mm
Power supply
Battery
AA alkaline battery x 6
Rated time when using alkaline batteries
Rated operating time / Rated resting time 0.5h / 1.0h
AC adapter
Type AST1116Z2-1
Manufacturer Seiko Epson Corp.
Input AC100-240V, 0.4A, 50-60Hz
(dedicated adapter, power cable only)
Output DC11V, 1.64A
Total output power 18 W
Safety Instructions
For your safety, read the attached documents carefully to use this product
correctly. After you have read all instructions, keep this manual handy for
future reference and to make your concerns clear.
Items below indicate safety precautions to protect users, their surroundings
and their property from possible injury or damage.
Meaning of the symbols
This indicates an important reminder.
This indicates a prohibited item.
This indicates a mandatory procedure.
DANGER
When handling batteries
If any liquid from the battery gets into your eyes, promptly wash it
out with clean water for more than 10 minutes and consult your
doctor at once. If you do not, the liquid may cause loss of eyesight.
Never disassemble or modify the battery. This may cause re,
explosion, leakage, overheating or damage.
Do not expose the battery to re or heat it. This may cause re,
explosion, leakage, overheating or damage.
WARNING
When using the AC adapter and power cable
The cords included with this product contain chemicals, including
lead, known to the State of California to cause birth defects or other
reproductive harm. Wash hands after handling. (This notice is
provided in accordance with Proposition 65 in Cal. Health & Safety
Code §25249.5 and following.)
Do not use any AC adapter or power cable other than the dedicated
AC adapter and power cable. Do not use the AC adapter with other
than the specied voltage also. Otherwise, damage, overheating,
re or electric shock may occur.
Take the following precautions when handling the AC adapter and
power cable.
• Make sure to avoid using multi-socket adapters.
• Make sure the plug is not dusty before inserting it into an outlet.
• Insert the plug rmly into the outlet.
• Do not hold the AC adapter or the plug with wet hands.
• Do not pull the power cable when disconnecting the plug. Be sure
to hold the plug when disconnecting it.
• Do not make any modication to the AC adapter or power cable.
• Do not apply strong shocks to or put a heavy object on the AC
adapter or power cable.
• Do not bend or twist the AC adapter or power cable forcibly.
• Do not place the AC adapter or power cable near a heater.
Do not use any damaged AC adapter or power cable. Otherwise,
damage, overheating or smoking may occur, which may result in re
or electric shock.
Do not touch the plug during thunderstorms.
When handling batteries
Keep the battery away from re or ame if it produces a strange
odor or leakage. Otherwise re or explosion may occur.
Should any battery liquid get on skin or clothing, promptly wash it
o with clean water. If you do not, the liquid may damage your skin.
Do not expose the battery to water. Do not allow water to contact
the terminals. This may cause re, overheating, or electric shock.
Keep batteries out of reach of children. They are extremely
dangerous if swallowed. Contact a doctor immediately if swallowed.
When using this product
Do not apply any strong force or shocks to the product such as
standing on, dropping or hitting it. Otherwise, the product may be
broken, which may result in re or electric shock. If it is damaged,
turn o the power immediately, unplug the AC adapter and remove
the batteries, and then contact the K-Sun customer support center.
Continuous use may result in re or electric shock.
Take care not to spill any beverage such as tea, coee or juice onto
the product, or to spray aerosol insecticide. It may cause
malfunction, re, or electric shock. If any liquid has been spilled on
the product, turn o the power, unplug the AC adapter and remove
the batteries immediately, and then contact the K-Sun customer
support center. Continuous use may result in re or electric shock.
"Name"
Menus and messages shown on the display,
and manual names are enclosed in double
quotes.
Do not touch the printhead because it becomes very hot.
Otherwise, there is a risk of burns.
Do not open any covers other than the top cover or battery cover.
Doing so may result in re or electric shock. Always use the product
as instructed in this manual. Otherwise, damage or injury may occur.
Never modify or disassemble this product. Doing so may cause re
or electric shock. Do not carry out any operations not described in
this manual, or the product may break or cause injury.
If any of the following abnormalities is observed, turn o the power
immediately, unplug the AC adapter and remove the batteries, and
then contact the K-Sun customer support center.
• If smoke, strange odors or unexpected noises come from the
product
• If liquid or foreign objects get inside the product
• If the product has been dropped or damaged
Do not touch the tape eject slot, during printing or when the auto
cutter is in operation. Otherwise there is a risk of injury.
When handling the PeelGuard®
When removing the PeelGuard tray, make sure to turn the power o.
If the product operates without the PeelGuard tray, injury or
damage may occur with the blade inside the product.
When cleaning the PeelGuard tray, do not touch the PeelGuard
blade, as there is a risk of injury. Do not insert anything other than
labels into the tape insertion slot. Otherwise, damage to the
PeelGuard may occur.
When handling the auto cutter
Do not touch the tape outlet slot (where the labels come out)
during printing or when the auto cutter is in operation. Otherwise,
there is a risk of injury.
Others
Do not use or store the product, batteries, AC adapter, power cable,
or tape cartridges in the following places.
• In direct sunlight.
• Where it may become extremely hot such as in a vehicle with the
windows closed.
• Where it may become extremely hot such as near a heater or the
temperature becomes very unstable such as near the exhaust duct of
an air conditioner.
• Where the product may get wet due to a shower or rain such as in
a bathroom or outdoors.
• In a dusty place or where the product may be exposed to smoke
or steam such as near the kitchen or a humidier.
• On an unstable place such as on a shaky table or on an inclined place.
• Where it might be subjected to vibration or shock.
• Near high-voltage power lines or something that generates a
magnetic eld.
Keep the plastic bags used to contain the product or this manual
out of reach of children. Children may suocate if they swallow
them or put their heads into the bags.
CAUTION
When handling batteries
If liquid leaks from a battery, wipe it o with a cloth and replace it
with a new one. If the liquid comes in contact with your skin, wash it
away with water immediately.
If the batteries are used incorrectly, they may cause leakage,
overheating, explosion, erosion, or damage to the product, which may
result in re or injury.
• Do not use new ones and old batteries together, or mix dierent types of
batteries.
• Use AA alkaline batteries.
• Use batteries in the correct directions.
• Take the batteries out immediately when they have no power
remaining.
• Take the batteries out if you do not use the product for a long
time.
• Do not heat batteries or throw them in re or water.
• Do not pinch the batteries with metal tweezers or use any pointed
sharp metal object such as the tip of a mechanical pen or ballpoint pen when taking the batteries out.
When disposing of used batteries, make sure to follow the
regulations.
When using the AC adapter
Do not unplug the AC adapter while the product is in operation,
otherwise printing may not be successful.
Do not use the AC adapter in a small, conned space, or cover it
with a cloth. Otherwise, the AC adapter may overheat and
deteriorate.
When using this product
Do not stand or put anything heavy on the product or place it on an
unstable place such as on a shaky table or on an incline. Otherwise,
the product may fall and cause injury.
To ensure safety, unplug this product before leaving it unused.
Before cleaning, make sure to unplug the AC adapter from the
outlet, and remove the batteries.
Do not use a moistened cloth or solvents such as alcohol, thinner or
benzine.
Do not block or insert objects into the supplied AC adapter socket
or the tape eject slot.
When handling tape cartridges
• Make sure to use a dedicated PX Tape.
• Some types of tape cannot be cut by the cutter. For the details, refer to
the tape's manual.
• Do not drop it or disassemble it. Doing so may cause damage.
• Do not pull out the tape forcibly by hand. But make sure to feed the tape
with
• Avoid using a tape cartridge without remaining tape. Doing so may
cause overheating of the printhead, which may result in damage or
malfunction.
. Otherwise, the tape cartridge may be broken and unusable.
MEMO
Tape cartridges contain ink ribbons in them. When disposing of tape
cartridges, make sure to follow the local regulations for disposal.
Other cautions
Notes on usage
• Do not touch the thermal head. Static electricity may damage the
thermal head.
• Do not plug in and unplug the AC adapter while printing. Power may be
cut o.
• Operate the keyboard gently.
• Take care not to cut your ngers when cutting the label with scissors.
• Do not attach a label on human bodies, living things, public facilities or
other people’s belongings.
• Be sure to turn the power o after use.
• Powering o message is displayed while turning o the product. Do not
remove the AC adapter until the message disappears.
• Be sure to replace batteries with the power turned o. If you replace the
batteries while the product is powered, les or data stored on it may be
deleted.
About the Symbols on this Product
On this product, the following symbols are used in order to ensure safety
and proper use of the product, and to prevent danger to users and other
persons as well as property damage.
The symbols indicate the meanings listed below. Be sure that you
completely understand the meaning of the symbols on this product before
using it.
On/Stand-by
Direct current
Hot surface
Polarity of D.C. power connector
Troubleshooting
Messages
This section explains the remedies when the following messages
appear on the display.
Check battery
Change alkaline
Cover open! Top cover is open. Close the top cover.
Insert tape Check if the tape cartridge is loaded or correctly
Check tape
cartridge
Length setting
is too short
No more
sequence No.!
No more barcode! Only up to 2 barcodes can be inserted.
QR CODE too big! Perform either of the following:
Overheated! The printhead is overheated. Turn o the power
Trash at slot
Remove trash
Remove cut tape Unable to start printing because cut tape
Problem
Unable to detect the tape correctly
Is the tape cartridge correctly installed?
Check that the tape cartridge is correctly installed.
Is the label for detecting the tape cartridge clean?
If not, wipe the dirt o with a soft cloth.
Is the detection sensor of the printer clean?
If not, wipe the dirt o with a soft cloth.
MEMO
If none of the above has solved the problem or the symptom is
other than the above, contact the K-Sun customer support center.
The batteries run out. Turn o the power and
replace all batteries with new ones.
set.
For details,
The loaded tape is not supported. Insert a
correct cartridge.
When label length is set to less than 1.8 cm, set
the label cutting method as follows.
Auto cut: On, Half cut: On
For details,
Only up to 2 sequence numbers can be inserted.
Use a wider tape. Reduce the text or cell size.
Lower "ECC Level".
and remove the tape cartridge, then leave the
printer until it cools down.
Tape remains in the tape eject slot. Remove the
tape.
remains in the tape eject slot. Remove the tape
from the tape eject slot.
"Installing a tape cartridge"
"Changing the Printer Settings"
6
78 9
15
16
25
Part Names and Functions
Body
23
24 22
1
2
3
4
5
1. Saves and recalls the label.
2. Feeds and then cuts the tape.
3. Prints a label. Hold down
press this to print with a special
print function.
4. Character keys
5. Shift
6. Turns the printer on and o.
and
20
21
19
7. Changes the input method of the
character keys. Hold down
and press this for caps lock.
8. Enters a character with an accent.
9. Space
10. Cursor keys
11. Enters a symbol.
12. Conrms the settings. Hold down
and press this to add a block.
18
17
14
13
12
11
10
13. Delete. Hold down
this to clear all text and/or setting.
14. Creates a barcode label.
15. Creates multiple labels at once.
Hold down
to create labels for wrap around
cable.
16. Creates an equipment
management label.
Hold down
to create labels for wrap around
cable like a ag.
17. Creates a general label, or escapes
from Flag label mode, Wrap label
mode, or Mix Length mode.
18. Text orientation
19. Changes the font size.
20. Change the font type.
21. Sets the format and style.
22. Sets the tape length. Hold down
and press this to sets the
margins.
23. Creates a label with a sequence
number.
Hold down
to create with block sequence
numbers.
24. Previews the created label. Hold
down
preference.
25. Display
and press this
and press this
and press this
and press this to display
and press
Display
The display shows the current settings and characters
you have entered.
You can change the language shown on the setting
screen and menu.
"Language" of "Changing the Printer Settings"
1. Set tape width and length
The unit can be switched between inch and cm.
2. Block number
3. Row number
4. Indicators
Displays the type, setting state, setting items,
and mode, etc. of the tape cartridge currently
set in
5. Cursor
6. Preview display
.
"Indicators"
Indicators
Remaining battery level
Displays font size.
"Changing the Font Size"
Half cut ON
"Auto cut" of "Changing the
Printer Settings"
Auto cut ON
"Auto cut" of "Changing the
Printer Settings"
The Heat Shrink Tube tape cartridge
is set.
The Self-Lamination Overwrap tape
cartridge is set.
Flag mode
"Creating Labels to Wrap
around Cable like a Flag"
Cable wrap mode (Creating cable
wrap label)
"Creating Labels to Wrap
Around Cable"
Mix-Length mode
"Creating Multiple Labels at
Once"
Symbol input mode
Caps Lock ON
Start Here
1. Connecting the supplied AC adapter
CAUTION
Be sure to use only the supplied AC adapter.
1. Connect the AC adapter as shown
below.
Using Label Editor Professional
CAUTION
Do not connect the printer to the computer until you are instructed to
do so.
Using batteries (commercially available)
CAUTION
• Be sure to turn o the power before installing the batteries.
• Use AA alkaline batteries. Other types of batteries cannot be used.
• When disposing of used batteries, make sure to follow the regulations.
• When you have printed continuously for 30 minutes using alkaline batteries,
leave the printer for at least one hour to allow the batteries to cool down.
1. Remove the
battery cover.
2. Insert the batteries with
the correct polarity.
3. Close the
battery cover.
4. Entering text
1. Press + .
2. Press
3. Press
A list of characters appears.
4. Select a character with
press .
"â" is entered.
5. Press keys:
"Câble" appears on the screen.
6. Press
7. Press
"#" is entered.
8. Press
input mode.
9. Press keys:
.
.
, ,
to switch to the symbol input mode.
.
to switch to the alphabet
, ,
/ and
Save the created label
Change the font
Change the font size
" Saving Frequently
Used Labels"
"Changing the Font"
" Changing the Font
Size"
Deleting text
1. Press .
A character is deleted backward.
Deleting all text
1. Press
2. Select a function with
then press .
Text Only
Deletes all text.
Text & Setting
Deletes all text and restores the font size and other
settings to the initial settings.
All Format
Deletes all text and format.
Depending on the label type you create, "All
Format" may not be displayed.
+ .
/ and
Label Editor Professional is an application software for editing
label. For how to install and operate the software,
see "Label Editor Professional User's Guide".
When you are prompted to connect the printer on the software
installer screen, connect the printer and the computer with a
USB cable.
2. Installing a tape cartridge
1. Rewind the ink ribbon.
CAUTION
• Make sure that the power is turned o.
• You cannot use tape other than PX-tape.
• Make sure the top cover is closed rmly.
• If you opened the top cover while a tape cartridge is
installed, check that the tape end is put into the tape
eject slot before beginning operation.
• Take care to keep the label for detecting the tape
cartridge and the sensor of the printer clean.
Otherwise, tape may no longer be detected correctly.
• Do not touch the sensor directly with your ngers.
Use a pen
or a pencil.
3. Install a tape cartridge.
Put the tape end
into the tape eject
slot.
5. Printing label
1. Press .
Setting the label auto
cut to O
Printing with special
print functions
Checking the print preview
1. Press
The print image scrolls on the entire screen.
When the preview ends, the editing screen reappears.
.
" Auto cut" of "Changing the
Printer Settings"
"Utilizing Print Functions"
6. Attaching label
CAUTION
• Do not insert your ngers into the tape eject slot.
• Do not pull the tape until the printing is completed.
Attention
• "Insert tape" will appear on the display if the tape
cartridge is not loaded or not correctly set.
• Length of the label shown on the display is a guide
and may not match the length of the printed label
exactly.
• Label over 16m in length cannot be printed.
MEMO
• To cancel the printing, press .
• Depending on your margin setting or the label type,
tape may be fed and cut before printing.
Detection label
Sensor
3. Turning the power on
1. Press .
2. Open the top cover.
Top cover
Feeding the tape
Be sure to feed the tape every time after you install
a tape cartridge.
CAUTION
Tape eject slot
4. Close the top cover.
1. Peel o the backing paper.
2. Attach the label and rub it rmly.
7. Turning the power o
CAUTION
Depending on the environment where you use labels
and the nature of the adhered surface, the labels may
be peeled or discoloured, and the adhesive may remain
on or damage the adhered surface. Be sure to check the
environment and the nature of the adhered surface
before use. K-Sun takes no responsibility for any damage
or loss due to the above mentioned causes.
Auto power-o
If there is no key operation within ve minutes, the printer
automatically turns o. (The characters you have entered in
the current session are stored.) Furthermore, if there is no key
operation within an hour while connected to a computer,
the printer automatically turns o.
1. Press .
2. Select a function with
press .
Tape feed
Feeds the tape.
Feed and cut
Feeds the tape and then cuts the tape.
/ and then
1. Press .
The characters you have entered in
the current session are stored even
after the printer is turned o. They
are displayed when it is turned on
again.
2. When using the AC adapter,
unplug the power cable from
the outlet and disconnect the AC
adapter plug from the printer.
CAUTION
• "Powering o." is displayed while turning o this
printer. Do not remove the batteries or disconnect
the AC adapter until this message disappears.
• When you don't use the printer for a long period of
time, remove the batteries, disconnect the AC
adapter, and remove the tape cartridge from the
printer.
Loading...