Epson EX100 User Guide

EX100

Multimedia Projector

User’s Guide

Important Safety Information

WARNING: Never look into the projector lens when the lamp is turned on; the bright light can damage your eyes. Never let children look into the lens when it is on. Never open any cover on the projector, except the lamp and filter covers. Dangerous electrical voltages inside the projector can severely injure you. Except as specifically explained in this User’s Guide, do not attempt to service this product yourself. Refer all servicing to qualified service personnel.

WARNING: The projector and its accessories come packaged in plastic bags. Keep plastic bags away from small children to avoid any risk of suffocation.

Caution: When you replace the lamp, never touch the new lamp with your bare hands; the invisible residue left by the oil on your hands may shorten the lamp life. Use a cloth or glove to handle the new lamp.

Copyright Notice

All rights reserved. No part of this publication may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, without the prior written permission of Seiko Epson Corporation. The information contained herein is designed only for use with this Epson product. Epson is not responsible for any use of this information as applied to other products.

Neither Seiko Epson Corporation nor its affiliates shall be liable to the purchaser of this product or third parties for damages, losses, costs, or expenses incurred by purchaser or third parties as a result of: accident, misuse, or abuse of this product or unauthorized modifications, repairs, or alterations to this product, or (excluding the U.S.) failure to strictly comply with Seiko Epson Corporation’s operating and maintenance instructions.

Seiko Epson Corporation shall not be liable for any damages or problems arising from the use of any options or any consumable products other than those designated as Original Epson Products or Epson Approved Products by Seiko Epson Corporation.

Trademarks

Epson, Instant Off, and EasyMP are registered trademarks and Epson Exceed Your Vision is a registered logomark of Seiko Epson Corporation.

PrivateLine is a registered trademark, SizeWise and Duet are trademarks, and Epson Connection and Epson Extra Care are service marks of Epson America, Inc.

Pixelworks, DNX, and the DNX logo are trademarks of Pixelworks, Inc.

General Notice: Other product names used herein are for identification purposes only and may be trademarks of their respective owners. Epson disclaims any and all rights in those marks.

This information is subject to change without notice.

Welcome . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

Using Your Documentation . . . . . . . . . . . . . . . . . . . . . . . . . . 8

Getting More Information . . . . . . . . . . . . . . . . . . . . . . . . 8

Registration and Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

Unpacking the Projector. . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

Additional Components. . . . . . . . . . . . . . . . . . . . . . . . . 10

Optional Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

Displaying and Adjusting the Image . . . . . . . . 13

Positioning the Projector . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

Projecting the Image. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

Turning On the Projector . . . . . . . . . . . . . . . . . . . . . . . 15

Selecting the Image Source. . . . . . . . . . . . . . . . . . . . . . . 17

Troubleshooting Display Problems. . . . . . . . . . . . . . . . . . . . 18

You Can’t Project an Image . . . . . . . . . . . . . . . . . . . . . . 18

The Projector and Notebook Don’t Display the

Same Image . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

Adjusting the Image . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20

Adjusting the Height of Your Image . . . . . . . . . . . . . . . 20

Focusing and Zooming Your Image . . . . . . . . . . . . . . . . 21

Adjusting the Image Shape. . . . . . . . . . . . . . . . . . . . . . . 21

Correcting Computer Images. . . . . . . . . . . . . . . . . . . . . 23

Using the A/V Mute Slide . . . . . . . . . . . . . . . . . . . . . . . 23

Shutting Down the Projector . . . . . . . . . . . . . . . . . . . . . . . . 23

Using the Direct Power On Function . . . . . . . . . . . . . . 24

Using the Remote Control . . . . . . . . . . . . . . . . . . . 25

Using the Remote Control . . . . . . . . . . . . . . . . . . . . . . . . . . 26

Replacing the Batteries. . . . . . . . . . . . . . . . . . . . . . . . . . 26

Controlling the Picture and Sound. . . . . . . . . . . . . . . . . . . . 27

Switching Between Picture Sources . . . . . . . . . . . . . . . . 27

Turning Off the Picture and Sound. . . . . . . . . . . . . . . . 28

Stopping Action. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28

Zooming Part of Your Image . . . . . . . . . . . . . . . . . . . . . 29

Controlling the Volume. . . . . . . . . . . . . . . . . . . . . . . . . 29

Resizing Video Images . . . . . . . . . . . . . . . . . . . . . . . . . . 30

Adjusting the Color Mode . . . . . . . . . . . . . . . . . . . . . . . 30

Operating Your Computer with the Remote Control. . . . . . 31

Highlighting Your Presentation . . . . . . . . . . . . . . . . . . . . . . 32

Using the Pointer Tool . . . . . . . . . . . . . . . . . . . . . . . . . 32

Customizing the Pointer Tool . . . . . . . . . . . . . . . . . . . . 32

Connecting to Computers and Other Equipment

Connecting to a Computer. . . . . . . . . . . . . . . . . . . . . . . . . . 34

Connecting to the Computer Port . . . . . . . . . . . . . . . . . 34

Connecting the Cable for Remote Mouse Control . . . . 35

Connecting to Video Equipment . . . . . . . . . . . . . . . . . . . . . 36

Connecting a Composite Video Source . . . . . . . . . . . . . 37

Connecting an S-Video Source . . . . . . . . . . . . . . . . . . . 38

Connecting a Component Video Source . . . . . . . . . . . . 39

Connecting an RGB Video Source. . . . . . . . . . . . . . . . . 40

Playing Sound Through the Projector . . . . . . . . . . . . . . . . . 41

. . . . . . . . . . . . . . . . . . . . . . . . . . . . 33

Fine-Tuning the Projector. . . . . . . . . . . . . . . . . . . 43

Using the Menu System . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44

Restoring the Default Settings . . . . . . . . . . . . . . . . . . . . 45

Adjusting the Image . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46

Six-Axis Color Adjustment. . . . . . . . . . . . . . . . . . . . . . . 47

Adjusting Signal Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . 48

Customizing Projector Features . . . . . . . . . . . . . . . . . . . . . . 50

Using the Projector Security Features . . . . . . . . . . . . . . . . . . 51

Enabling Password Protection . . . . . . . . . . . . . . . . . . . . 51

Creating Your Own Startup Screen . . . . . . . . . . . . . . . . 54

Disabling the Projector’s Buttons. . . . . . . . . . . . . . . . . . 56

Customizing Power and Operation . . . . . . . . . . . . . . . . . . . 56

Maintaining the Projector. . . . . . . . . . . . . . . . . . . 59

Cleaning the Lens . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60

Cleaning the Projector Case . . . . . . . . . . . . . . . . . . . . . . . . . 60

Cleaning the Air Filter and Vent. . . . . . . . . . . . . . . . . . . . . . 61

Replacing the Lamp and Air Filter . . . . . . . . . . . . . . . . . . . . 62

Resetting the Lamp Timer . . . . . . . . . . . . . . . . . . . . . . . 65

Transporting the Projector . . . . . . . . . . . . . . . . . . . . . . . . . . 66

Solving Problems . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67

Using On-Screen Help . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 68

Checking Projector Status. . . . . . . . . . . . . . . . . . . . . . . . . . . 69

What To Do When the Lights Flash . . . . . . . . . . . . . . . 69

Viewing Lamp Usage and Other Information . . . . . . . . 71

Solving Projector Operation Problems . . . . . . . . . . . . . . . . . 71

Solving Problems with the Image or Sound . . . . . . . . . . . . . 72

Solving Problems with the Remote Control . . . . . . . . . . . . . 77

Where To Get Help . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 78

Speak to a Support Representative . . . . . . . . . . . . . . . . . 78

Projector Installation . . . . . . . . . . . . . . . . . . . . . . . . 81

Technical Specifications . . . . . . . . . . . . . . . . . . . . . 83

Notices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .89

Important Safety Instructions . . . . . . . . . . . . . . . . . . . . . . . . 89

FCC Compliance Statement. . . . . . . . . . . . . . . . . . . . . . . . . 91

Index. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 93

Welcome

The EX100 is an easy-to-use projector that weighs less than 4 pounds

(1.8 kilograms) and offers up to 2700 lumens of white and color light output (brightness). You can connect it to a wide range of computers and video sources.

Easy setup, control, and security:

■ 5-second startup time and Instant Off

shut down

■ Automatic digital keystone correction

■ 1.2x optical zoom lens for flexible placement and positioning

■ Security features include password, user’s logo, and the ability to

lock the projector buttons

feature for fast setup and

■ A/V mute slide to block the lens and save lamp life when you

want to temporarily stop projecting

Using Your Documentation

This book contains all the information you need to set up and use your projector. Please follow these guidelines as you read through it:

■ Warnings must be followed carefully to avoid bodily injury.

■ Cautions must be observed to avoid damage to your equipment.

■ Notes contain important information about your projector.

■ Tips contain additional projection hints.

Getting More Information

Need tips on giving presentations? Quick steps for setting up your projector? Here’s where you can look for help:

■ Quick Setup sheet

Gives you the instructions you need to get your projector up and running if you are connecting to a notebook, MacBook PowerBook

■ Projector kit

, or iBook® computer.

Includes this User’s Guide, your Quick Setup sheet, warranty brochures, and Epson PrivateLine

Support card. Keep the kit

with your projector at all times.

8 Welcome

■ Built-in help system

Provides assistance for common problems. Available from the

Help button on the projector or the remote control. See page 68

for details.

■ epson.com/support

Download FAQs and e-mail your questions to Epson support.

■ If you still need help after checking this User’s Guide and the

sources listed above, you can use the Epson PrivateLine Support service to get help fast. Call (800) 637-7661 and enter the PIN on the PrivateLine card. Or take advantage of Epson’s automated support services 24 hours a day. See page 78 for more information.

■ presentersonline.com

Includes a library of articles covering presentation tips, tricks, and technology. The site provides templates, clip art and sound clips, as well as Presenters Services to use on the road. Even more resources and services are available if you register to join the Presenters Club—and it’s free.

Registration and Warranty

Your projector comes with a basic carry-in 2-year and 90-day lamp warranty. For details, see the warranty brochure included with your projector.

In addition, Epson offers free Extra Care unlikely event of an equipment failure, you won’t have to wait for your unit to be repaired. Instead, Epson will ship you a replacement unit anywhere in the United States or Canada, usually via overnight delivery. See the Extra Care Road Service brochure for details.

To register, simply fill out the registration card and mail it to Epson. Or register your product online using the projector CD or at this site: http://www.epson.com/webreg. Registering also lets you receive special updates on new accessories, products, and service.

Road Service. In the

Welcome 9

Unpacking the Projector

After unpacking the projector, make sure you have all the parts shown below:

Projector

Power cable VGA computer cable

Audio adapter

VGA-to-Component

PDF manual and

registration CD-ROM

Video adapter

Remote control and

2 AAA batteries

Carrying case

Save all packaging in case you need to ship the projector. Always use the original packaging (or the equivalent) when you need to send the projector to another location. If you are moving the projector by hand, use the carrying case. See page 11 for ordering information, and page 66 for transportation instructions.

Additional Components

10 Welcome

Depending on how you plan to use the projector, you may need additional components:

■ To receive an S-Video signal, you’ll need an S-Video cable. One

may be provided with your video equipment, or you can purchase one from Epson; see below.

■ To receive a component video signal from a VCR or other video

device, you’ll need the VGA-to-Component Video adapter

included with your projector and a component video cable. Or you can use a VGA-to-Component Video cable. You can purchase one from Epson; see below.

Optional Accessories

To enhance your use of the projector, Epson provides the following optional accessories:

Product Part number

Replacement lamp V13H010L38

Air filter replacement set (2 filters) V13H13408

Soft carrying case Simple soft carrying case Swiss Gear Wheeled soft case Soft shoulder case for projector and laptop ATA molded hardshell case

Universal ceiling mount Advanced projector ceiling mount with precision gear High security projector ceiling mount Adjustable suspended ceiling channel kit False ceiling plate kit Structural round ceiling plate Adjustable extension column (pipe) 8"-11"

Kensington

Duet™ portable projector screen 50-inch portable screen (4:3 aspect ratio) 60-inch portable pop-up screen (4:3 aspect ratio) 80-inch portable pop-up screen (4:3 aspect ratio)

VGA-to-Component Video cable S-Video cable

Distribution amplifier ELPDA01

Image presentation camera (ELPDC05) DC-10s Document Camera

backpack

security lock ELPSL01

143664 V12H001K60 ELPKS63 ELPKS62 ELPKS61 ELPKS58

ELPMBPJF ELPMBPRG ELPMBATA ELPMBP01 ELPMBP02 ELPMBP03 ELPMBC01

ELPSC80 ELPSC06 ELPSC07 ELPSC08

ELPKC19 ELPSV01

V12H162020 ELPDC10S

You can purchase screens, carrying cases, or other accessories from an Epson authorized reseller. To find the nearest reseller, call 800-GO-EPSON (800-463-7766). Or you can purchase online at www.epsonstore.com (U.S. sales) or www.epson.ca (Canadian sales).

Welcome 11

12 Welcome

Displaying and Adjusting the Image

Whether you’re presenting from a computer or video equipment,

you need to follow some basic steps to display your image on the screen.

Follow the guidelines in this chapter for:

■ Positioning the projector

■ Turning the projector on and selecting the image source

■ Troubleshooting display problems

■ Adjusting the image

■ Turning off the projector

note

You can mount the projector on the ceiling, or place it behind a translucent screen for rear projection. See page 81 for details.

Positioning the Projector

If the projector isn’t already installed in the room you’re using, you’ll probably want to place it on a table in front of the screen, as shown. This lets you stand in the front of the room, face the audience, and remain close enough to the equipment to be able to control it. Try to leave as much space as possible between the projector and the screen to get a good-size image.

Use the figure below to help you determine placement. Image size increases with distance, but can vary depending on how you position the zoom ring and whether you’ve adjusted the image with other settings.

TBD

33.1 to 39.7 ft (10 to 12.1 m)

Also keep these considerations in mind:

■ Place the projector on a sturdy, level surface.

■ Make sure there is plenty of space for ventilation around and

under the projector. Do not set the projector on top of anything that could block the vents under the projector.

■ Make sure the projector is within 10 feet (3 meters) of a grounded

electrical outlet or extension cord.

14 Displaying and Adjusting the Image

6.6 to 7.9 ft (2 to 2.4 m)

3.2 to 3.9 ft (0.9 to 1.2 m)

Distance from screen

Ideally, you should place the projector directly in front of the center of the screen, facing it toward the screen squarely. The base of the lens should be at about the level of the bottom of the screen.

Projector

Screen

If you place the projector below screen level, you’ll have to tilt it up by extending the front adjustable foot. This causes the image to become “keystone” shaped, but you can correct the distortion by pressing the buttons on the projector. See page 21 for detailed information about correcting the image shape.

For instructions on installing the projector in a permanent location, such as a theater or conference room, see page 81.

note

After positioning the projector, you may want to connect a Kensington MicroSaver device to the lock port on the projector. You can purchase this from Epson; see page 11.

anti-theft

Projecting the Image

Make sure your projector and other equipment are set up as described on page 33. Then follow the instructions below to start the projector and display an image.

Turning On the Projector

Turn on any connected computer or video equipment before starting the projector so it can automatically detect and display the image source. If you turn on the projector first, or have multiple pieces of connected equipment, you may have to select the image source manually (see page 17).

Displaying and Adjusting the Image 15

note

To shut down the projector, see page 23. Shutting down the projector correctly prevents premature lamp failure and possible damage from overheating.

Follow these steps to turn on the projector:

1. Open the A/V Mute slide (lens cover).

2. Plug one end of the power cable into the projector, and the other end into an electrical outlet.

Power light turns orange.

The

16 Displaying and Adjusting the Image

Power light

3. Press the red PPower button on the remote control or on top of

the projector.

The projector beeps once and the

Power light flashes green as the

projector warms up, then an image begins to appear. When the

Power light stops flashing and remains green, the projector is

ready for use.

4. If you’ve connected a Windows

-based computer to the projector, you may see a New Hardware Wizard screen saying your computer has found a plug-and-play monitor; if so, click

Cancel.

5. If you are prompted to enter a password, see page 51.

Selecting the Image Source

Selecting the image source lets you switch between images input from different pieces of connected equipment (such as a computer or DVD player).

If you don’t see the image you want, press the on the projector or the

Search button on the remote control until

you see the image you want to project.

You can also use the

Source buttons on the remote control to switch

between devices connected to the ports identified on each button. (The EX100 does not support EasyMP

Source Search button

warning

Never look into the lens when the lamp is on. This can damage your eyes, and is especially dangerous for children.

note

To focus and adjust the image, see page 20. If a projected image fails to appear, see page 18 for help.

Displaying and Adjusting the Image 17

Troubleshooting Display Problems

Follow these guidelines if you’re having trouble displaying an image.

You Can’t Project an Image

If you don’t see the image you are trying to project, try the following:

■ Make sure the cables are connected correctly, as described

beginning on page 33.

■ Make sure the Power light is green and not flashing and the A/V

Mute slide is open.

■ If you’ve connected more than one computer and/or video source,

you may need to press the projector’s control panel or to select the correct source. (Allow a few seconds for the projector to sync up after pressing the button.)

■ If you’re using a PC notebook, press the function key on your

keyboard that lets you display on an external monitor. It may be labeled hold down the

CRT/LCD or have an icon such as . You may have to

Fn key while pressing it. Allow a few seconds for

the projector to sync up after changing the setting.

Source Search button on the

Search button on the remote control

The Projector and Notebook Don’t Display the Same Image

note

Some notebooks cannot display the same resolution and/or aspect ratio on both the LCD screen and the projected image.

18 Displaying and Adjusting the Image

If you’re projecting from a notebook, and you can’t see your image on the projection screen and on your computer at the same time, follow these guidelines.

If you’re using a PC notebook:

■ On most systems, there’s a function key that lets you toggle

between the LCD screen and the projector, or display on both at the same time. It may be labeled

Allow a few seconds for the projector to sync up after changing the setting.

CRT/LCD or have an icon such as

. You may have to hold down the

Fn key while pressing it.

■ If the function key doesn’t permit you to display simultaneously

on both screens, you should check your monitor settings to make sure both the LCD screen and the external monitor port are enabled.

From the Control Panel, open the Properties dialog box, click the

Advanced (in Windows Vista

Display utility. In the Display

Settings tab, then click

, click Advance Settings). The method for adjusting the settings varies by brand; you may need to click a

Monitor tab, then make sure the external Monitor port

is set as your primary display and/or enabled. See your computer’s documentation or online help for details.

If you’re using Mac OS X:

You may need to set up your system to display on the projector screen as well as the LCD screen. Follow these steps:

1. From the Apple

Display or Displays.

2. Click

Detect Displays.

3. Make sure the

4. Click the

Arrangement or Arrange tab.

menu, select System Preferences, then select

VGA Display or Color LCD dialog box is selected.

Make sure Mirror Displays is checked

5. Make sure the

Mirror Displays checkbox is selected.

Displaying and Adjusting the Image 19

Adjusting the Image

Once you see your image, you need to make certain adjustments:

■ If the image is too high or too low, you can reposition it. See

below.

■ To focus or zoom your image, see page 21.

■ If the image isn’t square, see page 21.

■ If a computer image displays incorrectly, see page 23.

■ If you need to fine-tune the image and/or sound, see Chapter 4.

Adjusting the Height of Your Image

If the image is too low on the screen, you can use the front adjustable foot to raise it.

1. Stand behind the projector. Press the blue foot release lever up and lift the front of the projector.

2. Once the image is positioned where you want it, release the lever to lock the foot in position.

3. If necessary, you can fine-tune the height or level the image by turning the projector’s adjustable rear foot.

Projector rear foot

Raising the projector causes the image to distort or “keystone,” but you can correct the shape as described on page 21.

20 Displaying and Adjusting the Image

Focusing and Zooming Your Image

Turn the focus ring on the projector to sharpen the image.

Turn the zoom ring on the projector to reduce or enlarge the image.

Focus Zoom

If the image still isn’t large enough, you may need to move the projector farther away from the screen. You can also use the

E-Zoom

buttons on the remote control to zoom in on a portion of the image. See page 29 for instructions.

Adjusting the Image Shape

In most cases, you can maintain a square or rectangular image by placing the projector directly in front of the center of the screen with the base of the lens level with the bottom of the screen.

Even if the projector is slightly tilted (within a range of 30° up or down), the projector has an automatic keystone correction function that detects and corrects vertical keystone distortion.

Corrected imageProjector tilted up Projector tilted down

It takes about one second after projection starts for the image to be corrected. During this time, a vertical keystone correction gauge appears on the screen.

If your image is still distorted, you can correct it using the Keystone buttons on the projector’s control panel or the projector’s Setting menu.

Displaying and Adjusting the Image 21

Keystone correction

note

The image will be slightly smaller after adjusting. If it’s important to maintain the correct aspect ratio, use the menu system to perform keystone correction, then use the remote’s to adjust the aspect ratio. See page 30.

Resize button

Using Keystone Correction

To adjust your image when it is wider on the top or bottom, do the following:

■ Press one of the two triangular buttons on the projector’s control

panel, as shown below. Continue pressing the button until you are satisfied with the shape of the image.

■ Or press the Menu button on the remote control or projector,

select the

Setting menu, and press Enter.

From the Setting menu, select the pointer button on the remote control to adjust the keystone setting as needed.

If the image becomes uneven, decrease the sharpness setting. (See page 47.)

22 Displaying and Adjusting the Image

Keystone and press Enter. Use

Correcting Computer Images

If you’re connected to a computer and the image doesn’t look right, press the

Auto button on the remote control or the Enter button on

the projector. This automatically resets the projector’s tracking, sync, resolution, and position settings.

If the

Auto button doesn’t correct the problem, you may need to

adjust the tracking or sync using the projector’s Signal menu. See page 49 for more information.

Using the A/V Mute Slide

You can use the A/V Mute slide to temporarily turn off the image and sound when you want to redirect your audience’s attention.

note

You must be projecting an image for this button to have any effect. The works only with computer images projected through the VGA port.

Auto button

Shutting Down the Projector

When you’ve finished using the projector, follow the recommended procedure to shut it down. This extends the life of the lamp and protects the projector from possible overheating.

1. Turn off any equipment plugged into the projector.

2. To turn off the projector, press the red P

remote control or projector.

Power button on the

Displaying and Adjusting the Image 23

note

Lamp life results will vary depending on mode selected, environmental conditions, and usage.

Turn off this product when not in use to prolong the life of the projector.

You see a confirmation message. (If you don’t want to turn it off, press any other button.)

note

You can set the projector to automatically turn off the projector lamp and enter “sleep mode” when it has not received any signals for 30 minutes. This conserves electricity, cools the projector, and extends the life of the lamp. If you want to start projecting again, press the If you are done using the projector, unplug the power cord. To enable sleep mode, see page 57.

P Power button.

3. Press the P

Power button again. The

lamp turns off. When the projector beeps twice, you can unplug the power cord.

(If the projector is mounted on the ceiling, you will need to wait 20 seconds for the projector to cool down before you can unplug the power cord.)

If you want to turn the projector on again, make sure the orange light is not flashing, then press the P

Power button.

4. If you extended the adjustable front foot, press up on the blue foot release lever to retract it.

5. Close the A/V Mute slide.

Using the Direct Power On Function

The Direct Power On function enables faster setup. The projector will start up automatically when you plug it in; you won’t have to press the

Power button.

Follow these steps to enable Direct Power On:

1. Press the

Extended menu.

Menu button on the remote control and select the

2. Choose

3. Choose

note

If a power outage occurs when Direct Power On is enabled and the projector is plugged in, the projector will start when the power is restored.

24 Displaying and Adjusting the Image

4. Highlight

5. Press time you plug in the projector.

Operation and press Enter.

Direct Power On and press Enter.

On and press Enter.

Esc or Menu to exit. The setting will take effect the next

Using the Remote Control

The projector includes a number of tools to enhance your

presentation. All of them can be accessed using the remote control, which lets you operate the projector from anywhere in the room—up to 20 feet (6 meters) away.

note

For information and resources to help you give the most professional

resentation, be sure to visit

presentersonline.com.

You can use the remote control to adjust the picture and sound (page 27) or as a pointer to highlight your presentation (page 32). You can also use it to adjust the color mode for various environments (page 30) or as a wireless mouse when projecting from a computer (page 31).

This chapter covers:

■ Using the remote control

■ Controlling the picture and sound

■ Operating your computer with the remote control

■ Highlighting your presentation

note

If a button is pressed longer than 30 seconds, the remote control stops operating to conserve power. When you release the button, normal operation resumes.

Using the Remote Control

Follow these tips for using the remote control:

■ Point the remote control at the front of the projector or at the

screen.

■ Stand within 20 feet (6 meters) of the projector.

■ Avoid using the remote under bright fluorescent lamps or in

direct sunlight, or the projector may not respond properly.

Replacing the Batteries

caution

When replacing batteries, take the following precautions:

■ Replace the batteries as

soon as they run out. If the batteries leak, wipe away battery fluid with a soft cloth. If fluid gets on your hands, wash immediately.

■ Do not expose batteries to

heat or flame.

■ Dispose of used batteries

according to local regulations.

■ Remove the batteries if

you won’t be using the projector for a long period of time.

Replace the batteries as described below:

1. Turn the remote control over.

2. Press down on the tab on the battery cover as you lift the cover off.

3. Install two AAA batteries, inserting the

+ and – ends as

shown.

4. Position the cover as shown, then press down until it snaps into place.

26 Using the Remote Control

Controlling the Picture and Sound

You can use the remote control to preview and select your picture sources, temporarily turn off the picture and sound, freeze the action, zoom in on the picture, and adjust the volume.

Switching Between Picture Sources

If your projector is connected to more than one computer and/or video source, you can switch between the different sources:

■ The easiest way to select your source is to press the Search button

on the remote control (or the projector) repeatedly until you see the image you want on the screen.

Source Search button on the

■ On the remote control, there are four Source buttons. Use them

to switch between equipment connected to the port identified on each button.

After you select a source, the screen goes dark for a moment before the image appears.

Using the Remote Control 27

Turning Off the Picture and Sound

You can use the A/V Mute button on the remote control to turn off the image and sound. This does the same thing as the and is useful if you want to temporarily redirect your audience’s attention.

■ To turn off the picture and sound, press the A/V Mute button.

The screen turns black.

■ To turn the image and sound back on, press the button again.

A/V Mute slide

note

This function pauses the image, but not the sound. Also, because the source continues to transmit signals, you won’t resume the action from the point you stopped it.

You can have the screen turn blue when you press the

A/V Mute

button. You can also have an image, such as a company logo, display on the screen (see page 54).

Stopping Action

You can use the remote control to stop the action in your video or computer image.

■ To stop the action and keep the current image on the screen, press

Freeze button. The sound continues.

the

■ To restart it, press the Freeze button again.

28 Using the Remote Control

Zooming Part of Your Image

You can zoom in on a portion of the image using the E-Zoom buttons on the remote control.

1. Press the

E-Zoom button on the remote control.

You see a crosshair indicating the center of the zoom-in area.

2. Use the pointer button to position the crosshair.

3. Continue pressing the

E-Zoom button to enlarge the selected

area up to 4 times.

4. While the image is enlarged, you can:

■ Use the pointer button to move around the screen.

■ Press the E-Zoom button to zoom out.

5. When done, press the

ESC button to return the image to its

original size.

Controlling the Volume

To change the volume, press the or button on the remote control or projector.

note

To temporarily shut off the sound and picture, press the

A/V Mute button or close

the A/V Mute slide.

You can also adjust the volume using the projector’s menu system. See page 50.

Using the Remote Control 29

Resizing Video Images

You can use the Resize button on the remote control to adjust how an image fits into the display area.

For video images, press

Resize to switch the aspect ratio between 4:3

and 16:9, (and Normal for computer images). This lets you play certain digital video images or movies recorded on certain DVDs in 16:9 widescreen format.

For computer images, resizing is normally unnecessary, since the projector automatically resizes the image to make the best use of the display area. If you press the

Resize button on the projector or remote

control, the projector displays the image at the output resolution of the computer (which makes the image larger or smaller, depending on its resolution). If the resolution of the image is the same as the projector’s (1024

× 768), pressing Resize has no effect.

Adjusting the Color Mode

You can use the Color Mode button on the remote control to adjust the color, brightness, and other aspects of your image.

Press the button repeatedly to select from the following settings:

Photo: For vivid, high-contrast still images in a bright room.

Sports (video, S-video, or composite video only): For vivid TV

images projected in a bright room.

30 Using the Remote Control

Presentation: For computer presentations (the default when

projecting from a computer with analog video).

Theatre: For optimizing movie images with increased contrast.

Game: For increased brightness when playing video games or

watching TV in a bright room. Emphasizes dark gradations.

sRGB: For matching the color palette of standard sRGB computer

displays.

Blackboard: For projecting accurate colors on a green chalkboard

(adjusts the white point).

Customized: For manual color adjustment. (See page 46).

Operating Your Computer with the Remote Control

If you connect a computer to the projector with a USB cable, as described on page 35, then select in the Extended menu (see page 57), you can use the remote control in place of your computer’s mouse. This gives you more flexibility when delivering slideshow-style presentations, since you won’t have to stand next to the computer to change slides.

■ Use the Up and Down buttons to move through a

slideshow.

Page up or down to change slides in PowerPoint

Left-click

Link 21L for the USB Type B setting

Right-click

■ Use the pointer button to move the cursor on the screen.

■ Press the Enter button once to left-click, or press it twice to

double-click. Press the

■ To drag-and-drop, hold down the Enter button. Then use the

pointer button to drag the object. When it’s where you want it,

press

Enter to release it.

Esc button to right-click.

Using the Remote Control 31

Highlighting Your Presentation

You can display a pointer to call out important information on the screen. If you want to customize the pointer tool, you can choose from three alternative shapes.

Using the Pointer Tool

1. To activate the pointer tool, press the Pointer button on the remote control. A pointer appears on the screen.

Pointer

If you prefer to use a different style of pointer, see the instructions in the next section.

2. Use the pointer button on the remote control to position the pointer on the screen.

32 Using the Remote Control

3. When you’re done using the pointer, press

Esc to clear the screen.

Customizing the Pointer Tool

You can change the appearance of the pointer by choosing from three alternative shapes.

1. Press the

Settings menu, highlight Pointer Shape, and press Enter. You

can select one of the pointer shapes shown at the left.

2. Select the shape you want and press

3. Highlight

4. Press

Menu button on the remote control, highlight the

Enter.

Return and press Enter.

Menu to exit from the menu system.

Connecting to Computers and Other Equipment

This chapter tells you how to connect the projector to a notebook or

desktop computer, and/or to video equipment, such as a VCR, DVD player, or video camera.

Follow the instructions in this chapter on:

■ Connecting to a computer

■ Connecting video equipment

■ Playing sound through the projector

note

If you connect a Windowsbased computer to the projector, you may see a New Hardware Wizard saying your computer has found a plug-and-play monitor; if so, click Cancel.

Connecting to a Computer

You can connect the projector to any computer that has a standard video output (monitor) port, including desktop models, PC notebook and notebook computers, MacBooks, PowerBooks and iBooks, and hand-held devices. To connect to the blue

Video

port (standard VGA cable connection), see the instructions

below.

Connecting to the Computer Port

You can connect to the blue Computer/Component Video port using the VGA computer cable that came with the projector (the monitor port on your computer must be a mini D-sub 15-pin port).

1. If you’re using the VGA computer cable, connect one end to the projector’s blue other end to your computer’s monitor port. Then go to step 3.

Computer/Component Video port, and the

Computer/Component

caution

Don’t try to force a connector to fit a port with a different shape or number of pins. You may damage the port or connector.

34 Connecting to Computers and Other Equipment

2. You can connect an optional stereo mini-jack audio cable to play sound through the projector (see page 41), or connect a USB cable to use the remote control as a mouse (see page 35).

3. When you’ve finished making any connections, see page 15 for instructions on turning on the projector and adjusting the image.

Connecting the Cable for Remote Mouse Control

If you’ve connected a computer as described in this chapter (using the

Computer/Component Video port) and set the USB Type B setting

under the projector’s Extended menu to can use the projector’s remote control as a wireless mouse. This lets you control your computer and click through slideshow-style presentations, such as PowerPoint, from up to 20 feet away.

The wireless mouse function is supported on systems with a USB port running Windows 98SE, 2000, Me, or XP, or Mac OS

10.5.x. This function is not supported if you use an S-Video cable to

connect your computer to the projector.

1. Connect the square end of a USB cable to the projector’s

USB port.

Link 21L (see page 57), you

X 10.2.x to

note

The remote mouse control function may not operate correctly on systems that have been upgraded from an earlier version of Windows.

note

For details on how to use the remote control in place of your computer’s mouse, see page 31.

USB cable

2. Connect the flat end of the cable to any available USB port on your notebook or desktop computer.

3. If necessary, configure your computer to work with an external USB mouse. See your computer documentation for details.

Connecting to Computers and Other Equipment 35

Leftclick

Move cursor

Rightclick

Connecting to Video Equipment

You can connect several video sources to the projector at the same time. Before starting, look at your video equipment to determine its available video output connections:

RCA connector

(composite video)

S-Video connector

(4-pin mini-DIN)

VGA connector

(RGB video)

■ If your video player has a yellow RCA-style video output

connector, see “Connecting a Composite Video Source” on page 37.

■ If your video player has an S-Video connector, see “Connecting

an S-Video Source” on page 38.

■ If your video player has a component video port (three connectors

labeled either Y/Cb/Cr or Y/Pb/Pr), see “Connecting a Component Video Source” on page 39.

■ If your video player has an RGB video port (either a single

connector for a VGA-style monitor cable or three connectors labeled R/G/B), see “Connecting an RGB Video Source” on page 40.

After connecting video cables, you may also want to connect an audio cable to play sound through the projector; see page 41.

36 Connecting to Computers and Other Equipment

Connecting a Composite Video Source

1. Locate an RCA-style video cable (one is usually provided with your video equipment or you can purchase one from an electronics dealer).

2. Connect the cable to the yellow video output connector on your player and the yellow

3. If you want to play sound through the projector, see page 41 for instructions on connecting audio cables.

Video connector on the projector:

4. If you don’t need to make any other connections, see page 15 for instructions on turning on the projector and adjusting the image. Once the projector is turned on, select the image source: press the

Search button on the remote control or press the Source Search

button on the projector’s control panel repeatedly until

the image appears.

Connecting to Computers and Other Equipment 37

Connecting an S-Video Source

1. Locate an S-Video cable (one is usually provided with your video equipment or you can purchase one from Epson; see page 10).

2. Connect the cable to the S-Video connector on your player and

S-Video connector on the projector:

the

3. If you want to play sound through the projector, see page 41 for instructions on connecting audio cables.

Search button on the remote control or press the Source Search

the image appears.

button on the projector’s control panel repeatedly until

38 Connecting to Computers and Other Equipment

Connecting a Component Video Source

You will need a VGA-to-Component Video adapter (included with your projector) and a component video cable. Or you can use a VGA-to-Component Video cable (ELPKC19) from Epson; see page 11 for ordering information.

1. Locate a VGA-to-Component Video cable or adapter.

2. Connect the cable or cable and adapter to your video source and the blue projector.

Computer/Component Video connector on the

VGA-to-Component Video adapter

note

Be sure your video player is not an RGB video source. If you select the wrong source, image quality may suffer. Check your video player’s documentation.

Also, make sure the Computer Input setting in the Signal menu is set to Auto or Component Video (see page 49).

VGA-to-Component Video cable (ELPKC19)

3. If you want to play sound through the projector, see page 41 for instructions on connecting audio cables.

Search button on the remote control or press the Source Search

button on the projector’s control panel repeatedly until

the image appears.

Connecting to Computers and Other Equipment 39

Connecting an RGB Video Source

1. Locate the VGA computer cable provided with the projector.

note

Be sure your video player is not a component video source. If you select the wrong source, image quality may suffer. Check your video player’s documentation.

2. Connect the cable to the video port on your player and the

Computer/Component port on the projector.

3. If you want to play sound through the projector, see page 41 for instructions on connecting audio cables.

Search button on the remote control or press the Source Search

button on the projector’s control panel repeatedly until

the image appears.

40 Connecting to Computers and Other Equipment

Playing Sound Through the Projector

You can play sound through the projector’s speaker system.

To play sound through the projector, follow these steps:

1. Locate the appropriate cable and connect it to the

Audio jack on

the projector.

■ If you have a computer connected to the blue Computer/

Component Video

■ If you have video equipment connected to the Video or

S-Video port, use an RCA-style audio cable and the audio

port, use a stereo mini-jack cable.

adapter included with the projector.

Audio adapter

2. Connect the other end of the cable to the audio output connector(s) on your computer or video equipment.

Connecting to Computers and Other Equipment 41

42 Connecting to Computers and Other Equipment

Fine-Tuning the Projector

You can use the projector’s on-screen menus to adjust the image,

sound, and other features. This chapter covers the following information:

■ Using the menu system

■ Adjusting the image

■ Adjusting signal settings

■ Customizing projector features

■ Using the projector security features

■ Customizing power and operation

Using the Menu System

You can use the remote control or the projector’s control panel to access the menus and change settings. Follow these steps:

note

The Network option does not appear in the EX100 menu.

1. To display the menu screen, press the

Menu button on the

remote control or on the projector.

You see a menu screen similar to the one below:

Options

Menu list

2. Use the pointer button on the remote control (or the

3. Once you’ve selected the menu, use the pointer button to

44 Fine-Tuning the Projector

The menus are listed on the left and the options available for the highlighted menu are shown on the right.

navigational buttons on the projector) to scroll through the menu list. When you’ve highlighted the desired menu, press the

Enter

button to select it.

scroll through the list of options. (Some of the options may be grayed out or unavailable, depending on the selected source.)

4. After highlighting the option you want to adjust, use the

pointer button to change the setting. In some cases, you may

have to press the

Enter button to view a sub-screen for changing

the setting.

■ Press the left or right side of the pointer button to adjust

a slider bar.

■ To select from two or more settings, use the pointer

button to highlight the desired setting and press

Enter.

5. After changing the settings, press the

Esc button to save your

changes and return to the previous menu (or press it repeatedly to exit the menu system).

You can also press the

Menu button to exit.

Restoring the Default Settings

You can use the menu system’s Reset options to restore the factorydefault settings for all the settings listed in a specific menu, or all the settings in all menus.

To restore the settings in a specific menu, enter the menu whose settings you want to change, select (The example below shows how to reset the Image menu.)

Reset settings

for current menu

Reset settings for

all menus

To restore all the projector settings to their factory-default values, select the

Reset menu, highlight Reset All, and press Enter.

Reset, and confirm as needed.

note

When you select Reset All in the Reset menu, it does not reset the Computer Input, Video Signal, User’s Logo, Language, or Lamp settings.

Fine-Tuning the Projector 45

Adjusting the Image

You can use the Image menu to adjust the brightness, sharpness, color, tint, and contrast.

1. Press the select the

Menu button on the projector or remote control and

Image menu. You see the Image menu screen.

2. Use the pointer button to highlight the desired option, then adjust it as needed:

■ Color Mode

Lets you quickly adjust the color and brightness for various environments. Use either the remote control or the

Mode

setting in the Image menu. You can save a different

Color

setting for each source. Select from these settings:

Photo: For vivid, high-contrast still images in a bright room.

46 Fine-Tuning the Projector

Sports (video, S-video, or composite video only): For

vivid TV images projected in a bright room.

Presentation: For computer presentations (the default when

projecting from a computer with analog video).

Theatre: For optimizing movie images with increased

contrast.

Game: For increased brightness when playing video games or

watching TV in a bright room. Emphasizes dark gradations.

sRGB: For matching the color palette of standard sRGB

computer displays.

Blackboard

: For projecting accurate colors on a green

chalkboard (adjusts the white point).

Customized: For manual color adjustment. (See below.)

■ Brightness

Lightens or darkens the overall image.

■ Contrast

Adjusts the difference between light and dark areas.

■ Color Saturation (video only)

Adjusts the color depth of the image.

■ Tint (video only)

Adjusts the balance of green to magenta in the image (available only for component video or NTSC signals).

■ Sharpness

Adjusts the sharpness of the image.

■ Color Adjustment

Adjusts the color values. For Customized color mode, select

RGBCMY to adjust individual red, green, blue, cyan,

magenta, and yellow hue and saturation values. For other color modes, RGB may be selected to adjust red, green, and blue hue and saturation values. (Not available if

sRGB is

selected as the Color Mode setting.)

note

The Brightness setting changes the opacity of the projector’s LCD panels. You can also change the lamp’s brightness. Select

Brightness Control (light

output) in the Setting menu, then choose (the default setting is High).

High or Low

■ ABS Color Temp.

Sets a color temperature between 5000 and 10000 °K. (Not available if

sRGB is selected as the Color Mode setting.)

Six-Axis Color Adjustment

For special projection material, such as high-quality photographs or artwork, you can adjust the hue and saturation for six different color axes.

1. Follow the instructions on page 46 to open the Image menu and

Color Mode.

select

2. Press the return to the Image menu.

Enter button to select Customized, then press Esc to

Fine-Tuning the Projector 47

3. Select

Color Adjustment and press Enter. You see hue and

saturation controls on the screen for six colors: green, blue, cyan, magenta, and yellow.

RGBCMY (red,

note

You can also use the remote control’s automatically reset the projector’s tracking, sync, resolution, and position settings. See page 23 for details.

Auto button to

4. Select the color axis you want to adjust and press

Enter. You see

color controls for hue and saturation.

Hue changes the balance of color, and saturation changes the strength of the color.

5. Use the pointer button to adjust the hue and saturation. You see the adjustments reflected on the screen. When you are satisfied with the color, press

Esc.

6. Repeat steps 4 and 5 for each color axis you want to adjust.

You may need to readjust the color as the lamp in your projector changes over time.

Adjusting Signal Settings

Although the projector normally detects and optimizes the input signal automatically, you can use the Signal menu to make manual adjustments. In addition to changing the position of the projected image, you can correct tracking and sync for computer images, or change the aspect ratio to widescreen format for video images.

1. Press the

You see a screen similar to one of those below. (The settings will be different depending on the source you are projecting from.)

Menu button and select the Signal menu.

Computer/RGB Video

48 Fine-Tuning the Projector

Component Video Composite Video/S-Video

2. Use the pointer button to highlight the desired option, then adjust it as needed:

■ Auto Setup

Leave this setting

On to automatically optimize the computer

image. Turn it off if you want to save adjustments you have made to the video settings.

■ Tracking

Adjust this value to eliminate vertical stripes in the image.

■ Sync

Adjust this value if the image appears blurry or flickers.

■ Progressive

Turn this setting On to convert composite video signals into progressive signals (best for still images). Leave the setting

Off

for moving images.

■ Position

If the image is slightly cut off on one or more sides, it may not be centered exactly. Select this setting and use the pointer button to center it.

■ Computer Input

If the colors don’t look right on the Auto setting, select the setting for the type of equipment you’ve connected to the

Computer/Component Video port:

tip

Before adjusting tracking or sync, fill the screen with an image containing fine detail. For example, in Windows you can select a pattern to appear as your desktop background. If this option isn’t available, try projecting black text on a white background.

RGB: For a computer connection.

Component Video: For a video player that outputs a

component video signal.

■ Video Signal

Leave this setting at system (then select

■ Resize

Auto unless you are using a 60-Hz PAL

PAL60).

Choose an aspect ratio of either 4:3 or 16:9. Normal is the default setting for a computer connection.

Fine-Tuning the Projector 49

Customizing Projector Features

You can use the Settings menu to lock the buttons on the projector, adjust audio volume, and customize several other features.

■ Keystone

Squares up the shape of the image after the projector has been tilted upward. If you notice lines or edges looking jagged after adjusting the shape, decrease the Sharpness setting (see page 46).

■ Auto Keystone

Automatically compensates for keystone distortion when the projector is tilted upward. This feature is available only when the projector is set for front projection (it is enabled by default).

note

You can also adjust the volume using the remote control.

50 Fine-Tuning the Projector

■ Operation Lock

Lets you disable all of the buttons on the projector except the

Power button. See page 56 for more information.

■ Pointer Shape

Lets you choose from three alternative pointer shapes. See page 32 for more information.

■ Brightness Control

Lets you select from two levels of brightness. The Low setting reduces power consumption and noise, and extends the lamp’s operating life.

■ Volume

Raises or lowers the volume of the projector’s speaker.

Using the Projector Security Features

To prevent unauthorized use of the projector, you can do the following:

■ Assign a password; this can be disabled for a set period if you want

to loan the projector to someone.

■ Create an identifying user logo that is displayed at startup and/or

when the

■ Disable the projector’s buttons; this is useful, for example, if

you’re projecting in a classroom and you want to ensure that no one touches the projector’s buttons while you’re using the remote control. See page 56.

If you create a user’s logo for the projector, you can set up the logo so it is displayed as the startup screen and/or AV/Mute screen. Unauthorized users cannot turn it off or change it. This feature is intended to discourage theft and provides a way to identify the projector should it be stolen.

Enabling Password Protection

A/V Mute button is pressed. See page 54.

To prevent unauthorized use, you can assign the projector a password. If you do, a screen will appear requesting the password whenever the projector is plugged in and turned on. If an incorrect password is entered three times in succession, the projector’s operation is locked and the power cord must be disconnected and reinserted to redisplay the password screen. If an incorrect password is entered thirty times in succession, the user must contact Epson to unlock the projector.

The default setting for the Password Protect function is

Off. Follow

these steps to turn password protection on:

1. Press the

Freeze button on the remote control for about five

seconds.

Fine-Tuning the Projector 51

note

It’s a good idea to write down your password.

If you leave the projector plugged in, the Password Protect Release screen will not appear. You only need a password if you unplug and reconnect the power cable. Network Protect is not available for the EX100 projector.

caution

If you lose the remote control, you will not be able to enter the password. Keep the remote control in a safe place at all times.

You see this screen:

2. Use the pointer button to set

Enter.

press

3. Press

Esc.

Power On Protect to On. Then

4. Select Password and press Enter.

5. When you see a message asking if you want to change the password, select

Yes and press Enter.

6. Hold down the

Num button on the remote control and use the

numeric keypad to enter a four digit password. (The default setting is 0000.)

7. When you see a confirmation message, reenter the password. Then press the

8. Press the

Menu button to exit the screen.

Num button on the remote control to deactivate the

numeric keypad.

9. If you want to disable the password temporarily, select press

Enter. Then hold down the Num button while you use the

Timer and

numeric keypad to enter the number of hours (from 0 to 9999) that you want the password feature disabled. If you want the projector to request the password every time it is turned on, set the timer to

0H.

The countdown for the elapsed time begins as soon as you close the Password Protect menu. (You can check the elapsed time in this menu next to

Time elapsed.)

52 Fine-Tuning the Projector

10. To enable your screen logo, select User’s Logo Protect and press

Enter. Select On and press Enter.

When this feature is on, the logo appears whenever you turn on the projector (if the

Startup Screen is enabled in the Extended

menu; see page 54). It also appears when you press the A/V Mute button (if you selected the

Logo for the A/V Mute setting under

Display in the Extended menu). None of the User’s Logo features in the Extended menu can be changed when the User’s Logo Protect function is enabled.

Starting the Projector with a Password

When the password function is enabled, you see this screen when you plug in and turn on the projector:

Hold down the

Num button on the remote control and use the

numeric keypad to enter the four digit password.

The password screen closes, the numeric keypad is automatically deactivated, and projection begins.

If the password is not correct, you see a message prompting you to re-enter the password. If you enter an incorrect password three times in succession, you see the message

locked. Request code xxxxx

The projector’s operation will be

and the projector switches to standby mode for approximately 5 minutes. Write down the request code. Then disconnect the projector’s power cord from the electrical outlet, reconnect it, and turn the projector back on.

When you see the Password Protect Release screen again, you can try to enter the correct password.

Fine-Tuning the Projector 53

If you enter an incorrect password 30 times in succession, the projector remains locked and you must contact Epson to unlock it.

If you have forgotten the password, contact Epson with the request code number that appears in the Password Protect Release screen for assistance. See “Where To Get Help” on page 78.

Creating Your Own Startup Screen

You can transfer any image from your computer or video source to the projector and then use it as your startup screen. You can also use it as the screen displayed when the projector is not receiving a signal or when you press the logo, slogan, photograph, or any other image you want to use.

Capturing the Image

Start by displaying the image you want to use from either a computer or video source, such as a DVD player. Then follow these steps to capture the image and transfer it to the projector:

A/V Mute button. The image can be a company

1. Press the

Extended menu, and press Enter.

2. Highlight

Menu button on the remote control, highlight the

User’s Logo and press Enter.

3. When you see a message asking

user’s logo?

, select Yes and press Enter. A selection box displays

over the image.

Choose this image as the

54 Fine-Tuning the Projector

4. Use the pointer button to select the area of the image you

want to use. Then press

Enter.

5. When you see the message

and press

Enter.

Select this Image?, highlight Yes

6. Use the arrow buttons to select a zoom rate (display size) and press

Enter.

7. When the message

appears, select

Save this image as the user’s logo?

Yes and press Enter. Saving the logo may take a

few moments. Do not use your projector, remote control, or video source while the logo is being saved.

8. When you see the message

Completed, press Esc to return to the

menu screen.

Choosing When to Display the Image

After your image is saved, it is automatically set as the startup screen. You can also set it to display as the screen you see when there’s no signal or when you press the

1. Press the

Enter.

2. Select

Menu button, highlight the Extended menu, and press

Display and press Enter.

A/V Mute button (see page 28).

3. Highlight

A/V Mute, and press Enter.

4. Select

Display Background (for when there is no signal) or

Logo and press Enter.

5. When you’re finished, press Esc to exit.

Fine-Tuning the Projector 55

Disabling the Projector’s Buttons

note

Press the Enter button on the projector’s control panel for 7 seconds to disable the Operation Lock function.

When you enable the Operation Lock function, you can lock all the projector’s buttons, or all buttons except the

1. Press the

Enter.

2. Select

3. Select lock all buttons except the

4. Select

5. Press the

Menu button, highlight the Settings menu, and press

Operation Lock and press the Enter button.

Full Lock (to lock all projector buttons) or Partial Lock (to

Power button) and press Enter.

Yes and press Enter to confirm the setting.

Menu button to exit.

Power button.

Customizing Power and Operation

You can use the Extended menu to customize the way the projector displays images, enable quick startup, turn sleep mode on or off, and customize other projector operations.

■ Display

■ User’s Logo

56 Fine-Tuning the Projector

Use this setting to turn off the display of messages, change the background color, enable logo display, or turn off the startup screen display.

Create a custom startup screen, as described on page 54.

■ Projection

Select Front (to project from the front of a screen and right side

Front/Ceiling (when the projector is mounted upside down

up), from the ceiling), transparent screen), or

Rear (to project from behind onto a

Rear/Ceiling (to project from behind onto

a transparent screen when the projector is mounted upside down from the ceiling).

When you select one of the Ceiling projection methods, the projector requires a 10-second cool-down after you turn it off. You need to wait until you hear the projector beep before unplugging it.

■ Operation

Enable Direct Power On if you want to have the projector start when the power cable is connected (without pressing the button). Enable Sleep Mode if you want to have the projector turn off automatically if it is idle (and no signal is received) for 30 minutes or when the A/V Mute Slide is closed. Enable

Altitude Mode

when you are using the projector above 4900 feet

(1500 meters).

■ Link 21L

This setting is available only if you select Link 21L for the USB

Type B

setting. Select Off if you want to use the remote as a wireless mouse for a USB-connected computer. See page 35 for more information.

Power

High

note

If Direct Power On is enabled, the power cable is connected, and a power outage occurs, the projector will start when the power is restored.

Do not use the projector at altitudes above 7500 feet (2,286 meters).

■ Language

Select from nine languages to be used for the projector menus.

Fine-Tuning the Projector 57

58 Fine-Tuning the Projector

warning

Before you clean any part of the projector, turn it off and unplug the power cord. Never open any cover on the projector, except the lamp cover. Dangerous electrical voltages in the projector can injure you severely. Do not try to service this product yourself, except as specifically explained in this User’s Guide. Refer all other servicing to qualified service personnel.

Maintaining the Projector

Your projector needs little maintenance. All you have to do is keep

the lens clean. You may also need to clean the air filter and vent. A clogged air filter or vent can block ventilation needed to cool the projector.

The only parts you should replace are the lamp and air filter. If any other part needs replacing, contact your dealer or a qualified servicer.

This chapter covers the following:

■ Cleaning the lens

■ Cleaning the projector case

■ Cleaning the air filter and vent

■ Replacing the lamp and air filter

■ Transporting the projector

caution

Do not use wax, alcohol, benzene, paint thinner, or other chemical detergents. These can damage the case.

Cleaning the Lens

Clean the lens whenever you notice dirt or dust on the surface.

To remove dirt or smears on the lens, use lens-cleaning tissue. If necessary, moisten a soft cloth with lens cleaner and gently wipe the lens.

Cleaning the Projector Case

Before you clean the case, turn off the projector and unplug the power cord.

■ To remove dirt or dust, wipe the case with a soft, dry, lint-free

cloth.

■ To remove stubborn dirt or stains, moisten a soft cloth with water

and a neutral detergent. Then wipe the case.

60 Maintaining the Projector

Cleaning the Air Filter and Vent

Your projector includes an air filter to ensure the best performance. If dust collects on the air filter (on the bottom of the projector) or vent (on the front of the projector), clean them as described below. Dust clogs prevent proper ventilation and can cause overheating and damage the projector.

Follow these steps:

1. Turn off the projector. Wait for the then unplug the power cord.

2. To clean the intake vent and filter, use a small vacuum cleaner designed for computers and other office equipment. If you don’t have one, gently clean the vent with a soft brush (such as an artist’s paintbrush).

You can remove the air filter to clean both sides.

Power light to stop flashing,

note

To order replacement air filters, request part number V13H13408. See page 11 for ordering information.

Air filter

Vent

3. If the dirt is difficult to remove or the filter is broken, replace the filter as described on page 64. Contact your dealer or call Epson at 800-GO-EPSON (800-463-7766) to obtain a new filter.

Maintaining the Projector 61

note

When you get a replacement lamp for your projector, you should replace the filter.

Replacing the Lamp and Air Filter

The life span of the projection lamp is about 2000 hours if

Brightness Control in the Setting menu is set to High (default), and

3000 hours if

Brightness Control is set to Low.

To check how long the lamp has been in use, see page 71.

Turn off this product when not in use to prolong the life of the projector.

warning

Let the lamp cool fully before replacing it.

In the unlikely event that the lamp has broken, small glass fragments may be present and should be removed carefully to avoid injury.

It is time to replace the lamp when:

■ The projected image gets darker or starts to deteriorate.

■ The message Replace the lamp appears on the screen when the

lamp comes on and the lamp warning light flashes orange. To maintain projector brightness and image quality, replace the lamp as soon as possible.

■ The lamp warning light flashes red (the lamp is burnt out).

Contact your dealer or call Epson at 800-GO-EPSON (800-463-7766). Request part number V13H010L38.

Follow these steps to replace the lamp and air filter:

1. Turn off the projector.

2. When the

Power light stops flashing, unplug the power cord.

If the lamp is used after the replacement period has passed, the possibility that the lamp may break increases. When a lamp replacement message appears, replace the lamp with a new one as soon as possible, even if it is still working.

62 Maintaining the Projector

3. Let the projector cool for at least an hour (if it has been on). The lamp is extremely hot immediately after use.

4. Loosen the lamp cover screw (you don’t need to remove it). Then slide the lamp cover to the side and lift it off of the projector.

5. Loosen the two screws holding the lamp in place (you can’t remove them).

Loosen, but don’t remove these screws

6. Hold the lamp as shown and pull it straight out.

7. Gently insert the new lamp. (If it doesn’t fit easily, make sure it is facing the right way.)

Maintaining the Projector 63

note

The lamp(s) in this product contain mercury. Please consult your state and local regulations regarding disposal or recycling. Do not put in the trash.

8. Push down the corner marked

PUSH until it snaps in.

9. Once the lamp is fully inserted, tighten its screws.

10. Replace the lamp cover, then tighten its screw.

11. Slide out the air filter on the bottom of the projector and remove it.

12. Slide in the new air filter until it clicks in place.

13. Reset the lamp timer as described in the next section.

64 Maintaining the Projector

Resetting the Lamp Timer

After you replace the lamp, you need to reset the lamp timer using the projector’s menus.

1. Press the

Menu button on the remote control or on the

projector’s control panel. You see the main menu.

2. Use the pointer button on the remote control (or the arrow buttons on the projector) to highlight

Reset, then press Enter.

You see this screen:

3. Select

4. When you see the prompt, select

5. When you’re finished, press

Reset Lamp Hours and press Enter.

Yes and press Enter.

Esc or Menu to exit the Menu

system.

Maintaining the Projector 65

Transporting the Projector

The projector contains many glass and precision parts. Follow these guidelines to prevent damage:

■ When shipping the projector for repairs, use the original

packaging material if possible. If you do not have the original packaging, use equivalent materials, placing plenty of cushioning around the projector.

note

Epson shall not be liable for any damages incurred during transportation.

■ When transporting the projector a long distance, first place it in a

hard-shell shipping case, then pack it in a firm box with cushioning around the case. (An optional case is available from Epson; see page 11.)

■ Close the A/V Mute slide (lens cover) to protect the lens.

66 Maintaining the Projector

Solving Problems

This chapter helps you solve problems with your projector, and tells

you how to contact technical support for problems you can’t solve yourself. The following information is included:

■ Using the projector’s on-screen help system

■ What to do when the projector’s status lights flash

■ Solving projector operation problems

■ Solving problems with the image or sound

■ Solving problems with the remote control

■ Contacting technical support

Using On-Screen Help

If the image doesn’t look right or your audio isn’t working, you can get help by pressing the blue on the remote control. The following choices are available:

■ ”No Signal.” or no image appears on the screen

■ There is no sound

■ Select a different language

Follow these steps to get help:

? Help button on top of the projector or

1. Press the blue

? Help button on the remote control or on the

projector.

You see the Help Menu.

2. Use the pointer button on the remote control or the navigational buttons on the projector to highlight menu items.

3. Press the

Enter button on the remote control or on the projector

to select the menu item.

4. To exit the help system, press the

? Help button.

If none of the suggestions solve your problem, see additional solutions to problems in the following sections.

68 Solving Problems

Checking Projector Status

If your projector isn’t working correctly, first turn it off, wait for it to cool (the plug the power cord back in and turn on the projector. If this doesn’t solve the problem, check the lights on top of the projector.

What To Do When the Lights Flash

The lights on top of the projector indicate the projector’s status.

Power light

Power light stops flashing orange), and unplug it. Then

Temperature light

Lamp light

Refer to the following table for a complete description of the projector’s status lights:

Status lights

Light Status Description

Orange The projector is in sleep or standby mode. You can unplug it or press the

P Power button to turn it on.

Flashing green The projector is warming up. Wait for the image to appear.

Green The projector is operating normally.

Flashing orange The projector is cooling down. You can’t turn it back on (and you should

not unplug it) until the light stops flashing and remains orange.

Red There is a problem with the projector. Check the other two lights and the

information on page 70 to diagnose the problem.

Solving Problems 69

Status lights (continued)

Light Status Description

Flashing red There is a problem with the fan or temperature sensor. The air filter or

vent may be clogged. Clean them or replace the air filter as described on page 61.

If this does not resolve the problem, stop using the projector, disconnect the power cable, and contact Epson as described on page 78.

Flashing orange Rapid cooling is in progress. Although this is not an abnormal condition,

projection will stop automatically if the temperature rises higher. Make sure there is plenty of space around and under the projector for ventilation, and that the air filter and vents are clear.

Red The projector is overheating, which turns the lamp off automatically.

Wait until the cooling fan stops, then unplug the power cord. Plug the power cord back in and press the temperature is not above 95 °F (35 °C), and there is plenty of space around and under the projector for ventilation.

The air filter or vent may be clogged. Clean them or replace the air filter as described on page 61.

If the projector continues to overheat after you clean the air filter, the problem may be caused by damage to the cooling fan or temperature sensor. Contact Epson for help as described on page 78.

Warning: Except as specifically explained in this User’s Guide, do not attempt to service this product yourself.

P Power button. Make sure the room

Flashing orange It’s time to replace the lamp. See page 62 for instructions. If you continue

Flashing red The lamp may be burnt out. First make sure the lamp cover is securely

Flashing red Power is cut off because of an internal problem. Unplug the power cord

70 Solving Problems

to use the lamp after the replacement warning, there is an increased possibility that the lamp may break.

installed. If that’s not the problem, let the lamp cool, remove the lamp, and replace it as described on page 62.

The air filter or vent may be clogged. Clean them or replace the air filter as described on page 61.

If this does not resolve the problem, contact Epson as described on page 78.

and contact Epson for help, as described on page 78.

Viewing Lamp Usage and Other Information

Use the Info menu to view information about the display settings of your computer and the number of hours the lamp has been used.

Press the

Menu button and highlight the Info menu.

You see the lamp usage hours and various input signal settings on the right.

The life span of the lamp is about 2000 hours if the

Control

3000 hours if the

setting in the Setting menu is set to High (default), and

Brightness Control setting is set to Low. Make

Brightness

sure you have a spare lamp handy if the usage hours on this menu are close to the life span of your lamp.

Solving Projector Operation Problems

The power doesn’t turn on.

■ If the projector doesn’t turn on when you press the PPower

button, make sure the power cable is connected to the projector and plugged into a working electrical outlet.

■ The power cable may be defective. Disconnect the cable from the

outlet and contact Epson as described on page 78.

■ Check to see if the A/V Mute Slide is closed.

note

The information displayed depends on the input signal currently selected.

The buttons on the projector don’t work.

If the Operation Lock function has been enabled, you can’t use the buttons on the projector. Try using the remote control instead. See page 56 for information about the Operation Lock function.

Solving Problems 71

Solving Problems with the Image or Sound

No image appears on the screen.

■ Check that the Power light is green, not flashing.

■ The projector may be in standby or sleep mode. If the Power

light is orange, press the P on.

■ If the power was switched off and then on again, the projector

may be cooling down. Wait until the and remains orange; then press the P

■ Press the A/V Mute button on the remote control to make sure

the picture has not been turned off temporarily.

■ Open the A/V Mute Slide, if it is closed.

■ The attached computer may be in sleep mode or displaying a

black screen saver. Try pressing a key on the computer.

■ If you are projecting from a DVD player or other video source,

make sure you turn it on and press its

Power button to turn the projector

Power light stops flashing Power button again.

Play button.

72 Solving Problems

You’ve connected a computer and see a blue screen with the message No Signal displayed.

■ Make sure the cables are connected correctly, as described on

page 34.

■ Try restarting your computer.

■ If you’ve connected a computer and one or more video sources,

you may need to press the projector or one of the source buttons on the remote control to select the correct source. Allow a few seconds for the projector to sync up after pressing the button.

Source Search button on the

If you’re using a PC notebook:

■ Hold down the Fn key on the keyboard and press the function

key that lets you display on an external monitor. It may have an icon such as , or it may be labelled

CRT/LCD. Allow a few

seconds for the projector to sync up after pressing it. Check your notebook’s manual or online help for details.

On most systems, the key lets you toggle between the LCD screen and the projector, or display on both at the same time.

■ Depending on your computer’s video card, you might need to use

the Display utility in the Control Panel to make sure that both the LCD screen and external monitor port are enabled. See your computer’s documentation or online help for details.

If you’re using Mac OS X:

1. Open

2. Click

3. Click

4. Make sure the

5. Click the

6. Make sure the

System Preferences.

Display or Displays.

Detect Displays.

VGA Display or Color LCD dialog box is selected.

Arrangement or Arrange tab.

Mirror Displays checkbox is selected.

The message Not Supported is displayed.

■ Make sure the correct input signal is selected in the Signal menu

(see page 48).

■ Make sure your computer’s resolution doesn’t exceed UXGA

(1600

× 1200) and the frequency or refresh rate is supported by

the projector (see page 86). If necessary, change your computer’s resolution setting as described below.

Only part of the computer image is displayed.

■ Press the Auto button on the remote control.

■ Make sure the image Position setting is correct in the Signal

menu. See page 49 for more information.

Solving Problems 73

■ Press the Resize button on the remote control.

■ Press the Esc button on the remote control to cancel the E-Zoom

function.

note

Some notebooks cannot display the same resolution and/or aspect ratio on both the LCD screen and the projected image.

■ Make sure your computer’s resolution setting is correct. Ideally, it

should be 1024

× 768 to match the projector’s native resolution.

If this option isn’t available, select one of the other compatible video formats listed on page 86.

■ Windows:

Right-click the desktop, select

Properties, click the Settings

tab, and select a different resolution.

■ Mac OS X:

System Preferences, click Displays, and select a

Open different resolution.

■ You also may need to modify existing presentation files if you

created them for a different resolution. See your software documentation for specific information.

The image isn’t square, but keystone-shaped.

■ If the top or bottom of the image is broader, press the or

button on the projector until the image is square.

■ If the projector is angled toward the screen from the left or right,

the image will be broader on one side. Center the projector in front of the middle of the screen, facing the screen squarely.

74 Solving Problems

■ Enable the Auto Keystone feature to automatically fix the shape.

See page 50.

The image contains static or noise.

■ If you’re using a computer cable longer than 6 feet (1.8 meters),

or an extension cable, the image quality may be reduced.

■ Keep your computer and video cables away from the power cord

as much as possible to prevent interference.

■ The video signal may be split between the computer and the

projector. If you notice a decline in the projected image quality when the image is displayed simultaneously on your notebook computer and the projector, turn off the notebook’s LCD display.

■ Make sure the correct input signal is selected in the Signal menu

(see page 49).

The image is blurry.

■ There may be dirt or smears on the lens. Clean the lens as

described on page 60.

■ Adjust the focus using the focus ring (see page 21).

■ Make sure the lens is not fogged by condensation. You may need

to wait before using the projector after moving it from a cold environment to a warm environment.

■ Adjust the Sharpness setting on the Image menu (see page 47).

When you change video settings, you should be able to see the effect on the screen immediately. If you’re projecting from a computer, you may also need to adjust the tracking and sync as described in the next section. If you don’t like the new settings, you can always select settings.

Reset to return to the factory default

You see vertical bands or the image still looks blurry after trying the solutions in the previous section.

■ If you’re projecting from a computer and displaying an image that

contains a lot of fine detail, you may notice vertical bands or some of the characters may look heavy or blurred. Press the button on the remote control to reset the projector’s tracking and sync settings.

■ If further adjustment is needed, you can fine-tune the Tracking

and

Sync settings manually using the Signal menu, as described

on page 49.

1. Fill the screen with an image containing fine detail, such as a pattern to appear as your desktop background, or try projecting black text on a white background.

Auto

Solving Problems 75

2. Adjust the

Tracking to eliminate vertical bands.

note

Because of the different technologies used, your projected image may not exactly match the colors on your notebook or computer monitor.

3. Adjust the

Sync setting to increase the image sharpness.

The image is too light or dark, or colors are incorrect.

■ If you’re displaying a computer image, use the Color Mode

option in the projector’s Image menu to adjust the color (see page 46).

■ If you’re displaying video, adjust the Color Adjustment and

Color Mode settings on the Image menu. You can also try

adjusting the settings on the Image menu.

■ Try adjusting the Brightness and Contrast settings on the Image

menu.

■ Check your computer display settings to correct the color balance.

Color Saturation, ABS Color Temp, and Tint

76 Solving Problems

■ The projector’s lamp may need to be replaced. See page 62 for

instructions.

There is no sound, or the sound is not loud enough.

■ Press the button on the projector or remote control to increase

the volume.

■ Make sure A/V Mute is not enabled. (The A/V Mute button may

have been pressed.)

■ Make sure the A/V Mute Slide is open.

■ Try adjusting the Volume setting in the Setting menu (see

page 50).

■ If you’re using a VCR or other video source, make sure the

volume is not turned all the way down or muted. Also, make sure the cables are connected correctly, as described on page 41.

■ If your presentation includes computer audio, make sure the

volume control on your computer is not turned all the way down or muted. If you’re using the audio cable, make sure it is securely connected to both the projector and your computer’s

headphone jack or audio out jack.

■ Make sure the Windows volume controls on your computer are

not turned all the way down or set to Mute. You may be able to check this by clicking the volume control in your Windows system tray (lower right corner of the screen).

■ Make sure the Mac volume controls are not turned all the way

down. You may be able to adjust the volume from your menu bar (top right corner of the screen) or via the volume control function keys.

Solving Problems with the Remote Control

The projector doesn’t respond to remote control commands.

■ The remote control’s batteries may not be installed correctly or

may be low on power. To change the batteries, see page 26.

■ Make sure you are within about 20 feet (6 meters) of the projector

and within range of the projector’s front or back sensor (approximately 30° to the left or right and 15° above or below).

■ Dim the room lights and turn off any fluorescent lights. Make

sure the projector is not in direct sunlight. Strong lighting, especially fluorescent lights, may affect the projector’s infrared receivers. Also, turn off any nearby equipment that emits infrared energy, such as a radiant room heater.

Solving Problems 77

■ If any buttons are held for longer than 30 seconds, the remote

enters sleep mode. Release any button that is held to wake the remote.

Where To Get Help

Epson provides these technical support services:

Internet Support

Visit Epson’s support website at www.epson.com/support and select your product for solutions to common problems. You can download utilities and documentation, get FAQs and troubleshooting advice, or e-mail Epson with your questions.

Visit http://www.presentersonline.com to access tips, templates, and training for developing successful presentations.

Speak to a Support Representative

To use the Epson PrivateLine Support service, call (800) 637-7661 and enter the PIN on the included Epson PrivateLine Support card. This is the fastest way of speaking to a live representative, and it’s free. This service is available 6 Friday, for the duration of your warranty period.

AM to 6 PM, Pacific Time, Monday through

78 Solving Problems

You may also speak with a projector support specialist by dialing one of these numbers:

■ U.S.: (562) 276-4394, 6 AM to 6 PM, Pacific Time, Monday

through Friday.

■ Canada: (905) 709-3839, 6 AM to 6 PM, Pacific Time, Monday

through Friday.

Days and hours of support are subject to change without notice. Toll or long distance charges may apply.

Before you call for support, please have the following information ready:

■ Product name (EX100)

■ Product serial number (located on the projector)

■ Proof of purchase (such as a store receipt) and date of purchase

■ Computer or video configuration

■ Description of the problem

Purchase Supplies and Accessories

Solving Problems 79

80 Solving Problems

Projector Installation

This appendix provides guidelines on installing the projector in a

permanent location, such as a theater or conference room.

The projector can be installed for four different viewing setups: front projection, ceiling projection, rear projection onto a semi-transparent screen, or rear/ceiling projection, as shown:

Front projection Rear projection

Rear/ceiling projectionCeiling projection

To project from overhead, you’ll need the optional ceiling mounting hardware; see page 11 for ordering information. You’ll also need to select

Front/Ceiling or Rear/Ceiling as the Projection option in the

projector’s Extended menu to flip the image upside-down. To project from the rear, onto a semi-transparent screen, select

Rear/Ceiling (see page 57).

Rear or

If you’re mounting the projector on the ceiling and you place it above screen level, you’ll have to tilt the projector down to position the image on the screen. This causes the image to lose its square shape. You can correct the distortion using the

Keystone function in the

projector’s menu system (see page 50).

If you place the projector so that the base of the lens is level with the bottom of the screen, the image should be square and you won’t have to adjust it. If you place the lens lower than the bottom of the screen, you’ll have to tilt the projector upward if you want to fill the whole screen with the image.

82 Projector Installation

Technical Specifications

General

Type of display Epson poly-silicon TFT active matrix

Resolution (native format) 1024 × 768 pixels (XGA)

Color reproduction 16.8 million colors

Light Output (brightness) High mode:

White light output 2700 lumens (ISO 21118 standard) Color light output 2700 lumens

Low mode: White light output 2100 lumens (ISO 21118 standard) Color light output 2100 lumens

Contrast ratio 400:1

Image size 30 to 300 inches (0.7 to 7.6 meters)

Projection distance 3.2 to 39.7 feet (1.0 to 12.1 meters)

Projection methods Front, rear, upside down (ceiling mount)

Internal sound system 1 W monaural

Optical aspect ratio 4:3 (horizontal:vertical)

Zoom ratio 1:1.2

Noise level 35 dB in Low Brightness mode, 40 dB in

High Brightness mode

Keystone correction Automatic (manual adjustment capability

±30° vertical keystone correction)

Mouse compatibility Supports USB (type B)

Projection Lamp

Type UHE (Ultra High Efficiency)

Power consumption 170 W

Lamp life Approx. 2000 hours (High Brightness

mode) Approx. 3000 hours (Low Brightness mode)

Part number V13H010L38

Remote Control

Range 20 feet (6 meters)

Batteries (2) Alkaline AAA

Dimensions

Height 2.7 inches (68 mm), feet retracted

Width 10.7 inches (273 mm)

Depth 7.6 inches (193 mm)

Weight 3.5 lb (1.6 kg)

84 Technical Specifications

Electrical

Rated frequency 50/60 Hz AC

Power supply 100 to 120 VAC, 2.7 A

200 to 240 VAC, 1.2 A

Power consumption Operating:

100 to 120 VAC, 244 W 200 to 240 VAC, 228 W

Standby: 100 to 120 VAC, 3.8 W 200 to 240 VAC, 5.1 W

Environmental

Temperature Operating: 41 to 95 °F (5 to 35 °C)

Storage: 14 to 140 °F (–10 to 60 °C)

Humidity (non-condensing) Operating: 20 to 80% RH

Storage: 10 to 90% RH

Operating altitude 0 to 7,500 ft (0 to 2,286 m)

Safety

United States FCC 47CFR Part 15B Class B (DoC)

UL60950 Third Edition

Canada ICES-003 Class B

CSA C22.2 No. 60950

CE Marking Directive 73/23/EEC

Directive 89/336/EEC IEC 60950 Third Edition EN 55022, EN 55024

Pixelworks

™

DNX™ ICs are used in this projector.

Technical Specifications 85

Compatible Video Formats

The projector supports NTSC, PAL, and SECAM international video standards, as well as the monitor display formats listed below.

To project images output from a computer, the computer’s video card must be set at a refresh rate (vertical frequency) that’s compatible with the projector. Some images are automatically resized to display in the projector’s “native” format (XGA). The frequencies of some computers may not allow images to display correctly; see your computer’s documentation for details.

Mode Refresh Rate (Hz) Resolution

VGA EGA 70 640

VGA—60 VESA—72 VESA—75 VESA—85

SVGA—56 SVGA—60 SVGA—72 SVGA—75 SVGA—85

XGA—60 XGA—70 XGA—75 XGA—85

SXGA1—70 SXGA1—75 SXGA1—85

SXGA2—60 SXGA2—75 SXGA2—85 SXGA+60 SXGA+75 SXGA+85

SXGA3—60 SXGA3—75 SXGA3—85

60 72 75 85

56 60 72 75 85

60 70 75 85

70 75 85

60 75 85 60 75 85

60 75 85

UXGA—60 60 1600 × 1200

× 350

× 480

× 600

× 768 × 768 × 768 × 768

× 864

640 640 × 480 640 × 480 640 × 480

800 800 × 600 800 × 600 800 × 600 800 × 600

1024 1024 1024 1024

1152 1152 × 864 1152 × 864

1280

× 960

1280 × 960 1280 × 960 1400 × 1050 1400 × 1050 1400 × 1050

1280

× 1024

1280 × 1024 1280 × 1024

86 Technical Specifications

Mode Refresh Rate (Hz) Resolution

iMAC VGA iMAC SVGA iMAC XGA MAC13 MAC16 MAC19 MAC19-60 MAC21

NTSC NTSC 4:43 PAL N-PAL M-PAL PAL—60 SECAM

HDTV (720p) HDTV (720p) HDTV (1080i) HDTV (1080i)

TV480i TV480i SDTV (480p)

SDTV (480p)

The image is resized using Epson’s SizeWise™ Technology.

117 95 75 67 75 75 59 75

60 60 50 50 60 60 50

60 50 60 50

60 50 60

640

× 480

800 × 600 1024 × 768 640

× 480

832 × 624 1024 × 768 1024

× 768

1152

× 870

— — — — — — —

— — — —

Technical Specifications 87

88 Technical Specifications

Notices

This appendix includes safety instructions and other important information

about your projector.

Important Safety Instructions

Follow these safety instructions when setting up and using the projector:

■ Do not place the projector on an unstable cart, stand, or table.

■ Do not use the projector near water or sources of heat.

■ Use the type of power source indicated on the projector. If you are not

sure of the power available, consult your dealer or power company.

■ Place the projector near a wall outlet where the plug can be easily

unplugged.

■ Do not hold the plug with wet hands.

■ Take the following precautions for the plug. Failure to comply with

these precautions could result in sparks or fire: Do not insert the plug into an outlet with dust present. Insert the plug firmly into the outlet.

■ Do not overload wall outlets, extension cords, or integral convenience

receptacles. This can cause fire or electric shock.

■ Do not place the projector where the cord can be walked on. This may

result in fraying or damage to the plug.

■ Unplug the projector from the wall outlet before cleaning. Use a damp

cloth for cleaning. Do not use liquid or aerosol cleaners.

■ Do not block the slots and openings in the projector case. They provide

ventilation and prevent the projector from overheating. Do not operate the projector on a sofa, rug, or other soft surface, or in a closed-in cabinet unless proper ventilation is provided.

■ Never push objects of any kind through the cabinet slots. Never spill

liquid of any kind into the projector.

■ Except as specifically explained in this User’s Guide, do not attempt to

service this product yourself. Refer all servicing to qualified personnel. Opening or removing covers may expose you to dangerous voltages and other hazards.

■ Unplug the projector from the wall outlet and refer servicing to qualified

service personnel under the following conditions: When the power cord or plug is damaged or frayed. If liquid has been spilled into the projector, or if it has been exposed to rain or water. If it does not operate normally when you follow the operating instructions, or if it exhibits a distinct change in performance, indicating a need for service. If it has been dropped or the housing has been damaged.

■ The lamp(s) in this product contain mercury. Please consult your

state and local regulations regarding disposal or recycling. Do not put in the trash.

■ Unplug the projector during lightning storms or when it will not be used

for extended periods.

■ Do not place the projector and/or remote control on top of

heat-producing equipment or in a hot location.

■ If you use the projector in a country other than where you purchased it,

use the correct power cord for that country.

■ Do not stand on the projector or place heavy objects on it.

■ Do not use the projector outside of the required temperature range of 41

to 95 °F (5 to 35 °C). Doing so may cause an unstable display and could lead to projector damage.

■ Do not store the projector outside of the required temperature range of

14 to 140 °F (–10 to 60 °C) or in direct sunlight for long periods of time. Doing so may cause damage to the case.

90 Notices

WARNING: The cords included with this product contain chemicals, including lead, known to the State of California to cause birth defects or other reproductive harm. Wash hands after handling. (This note is provided in

accordance with Proposition 65 in Cal. Health & Safety Code §25249.5 and following.)

FCC Compliance Statement

For United States Users

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio or television reception. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause interference to radio and television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

■ Reorient or relocate the receiving antenna.

■ Increase the separation between the equipment and receiver.

■ Connect the equipment into an outlet on a circuit different from that to

which the receiver is connected.

■ Consult the dealer or an experienced radio/TV technician for help.

WARNING

The connection of a non-shielded equipment interface cable to this equipment will invalidate the FCC Certification of this device and may cause interference levels which exceed the limits established by the FCC for this equipment. It is the responsibility of the user to obtain and use a shielded equipment interface cable with this device. If this equipment has more than one interface connector, do not leave cables connected to unused interfaces. Changes or modifications not expressly approved by the manufacturer could void the user’s authority to operate the equipment.

For Canadian Users

This Class B digital apparatus meets all requirements of the Canadian Interference-Causing Equipment Regulations.

Cet appareil numérique de la classe B respecte toutes les exigences du Règlement sur le materiel brouilleur du Canada.

Notices 91

92 Notices

Index

A/V Mute, 23, 28, 55, 72 Accessories, 11 Adapter, audio, 10, 41 Air filter

cleaning, 61 ordering, 11

replacing, 62 to 64 Altitude, 57, 85 Anti-theft device, 11, 15 Aspect ratio, 83 Audio

adapter, 10, 41

controlling volume, 29

problems, troubleshooting, 76 to 77

turning off (using A/V Mute), 28 Auto button, 23 Auto Setup setting, 49

Bands, vertical, 75 Blackboard color mode, 30, 47 Blackboard, projecting on, 30 Blank screen, 18 to 19 Blurry image, 75 Brightness, 83 Brightness setting, 47

Cables

illustrations, 10

mouse, 35

ordering, 11

remote control cable set, 11

S-video, 11, 38

VGA-to-Component Video, 39 Capturing image, 54 to 55 Carrying case, 10, 66

Cases, 11 Ceiling mount, 11, 81 to 82 Cleaning

air filter, 61 lens, 60 projector case, 60

Color

correcting, 30 problems, 76 saturation, 47 settings, 46 to 47

temperature, 47 Color Mode setting, 46 Component video cable, 11, 36 Composite (RCA) video cable, 36 to 37 Computer

connecting to, 34 to 35

correcting images, 23

selecting source, 17 Connecting projector

to a computer, 34 to 35

to video equipment, 36 to 40 Contrast setting, 47 Customized color mode, 30, 47

Default settings, restoring, 45 Direct Power On, 24 Distance from projector to screen, 14, 83 Documentation, 8 DVD player, connecting, 36 to 40

Electrical specifications, 84 Environmental specifications, 85

Epson

accessories, 11 presentation tips, 9 PrivateLine Support, 8 technical support, 8, 78 to 79

E-Zoom button, 29

FCC compliance statement, 91 Filter, see Air filter Focusing image, 21 Freeze button, 28

Game color mode, 30, 46

HDTV images, video formats, 87 Height of image, adjusting, 20 Help, 78 to 79 Help system, using, 68 Help, Epson, 8 High altitude, 57

Input signal, selecting, 17, 27, 37 to 40 Installing projector, 81 to 82

Kensington anti-theft device, 11, 15 Keystone correction, 21 to 22, 50, 74, 83

Lamp

number of hours used, 71 ordering, 11 replacing, 62 to 65 specifications, 84

status light, 69 to 70 Lamp timer, resetting, 65 Language setting, 57, 68 Laptop computer

connecting to, 34 to 35

display problems, 18 to 19, 72 to 73

selecting source, 17, 27 Lens, cleaning, 60 Lights, status, 69 to 70 Logo, saving on projector, 54 to 55

Image

adjusting, 20 to 23, 46 to 47 blurry, 75 capturing and saving in projector, 54 to 55 correcting shape, 21 to 22, 50, 74 fitting on screen, 49, 73 to 74 height, adjusting, 20 problems with, 72 to 76 projecting on chalkboard, 30 raising, 20 selecting source, 17, 27, 37 to 40 size and projection distance, 14, 83 turning off (using A/V Mute), 23, 28

zooming, 21, 29 Image menu, 46 to 47 Info menu, 71

94 Index

Mac

display problems, 73

resolution setting, 74 Manuals, 8 Menus

changing settings, 44 to 45

default settings, restoring, 45

Image, 46 to 47

Info, 71

Signal, 48 to 49

User’s Logo, 54 to 55 Mouse

compatibility, 83

connecting cable for remote, 35

using remote control as, 31

New Hardware Wizard, 17 No Signal message, 18, 72 to 73 Noise level, 83 Not Supported message, 73 Numeric keypad, using, 52

Operation Lock setting, 56 Optical aspect ratio, 83 Options for projector, 11

Password

protection, 51 to 54

request code, 53 Photo color mode, 30, 46 Picture source, selecting, 17, 27, 37 to 40 Picture, see Image Pointer tool, using, 32 Positioning

image, 20

projector, 14 to 15, 81 to 82 Power

button, 17

specifications, 84

status light, 17, 69 to 70 Presentation color mode, 30, 46 Presentations

computer, 23, 34 to 35

room conditions, 14, 26

tips and training, 9

using the pointer tool, 32

video, 36 to 40 Presenters Online, 9 PrivateLine Support, 8

Problems

color, 76 image, 72 to 76 no signal, 18, 72 to 73 remote control, 77 sound, 76 to 77

using on-screen help, 68 Progressive format, 49 Projecting without screen, 30 Projection lamp, see Lamp Projector

carrying case, 66

cleaning, 60

disabling buttons, 56

distance from screen, 14, 83

installing, 81 to 82

lamp specifications, 84

options, 11

password protection, 51 to 54

positioning, 14 to 15

resolution, 83

specifications, 83 to 85

transporting, 66

troubleshooting, 67 to 70

turning off, 23 to 24

turning on, 15 to 17

unpacking, 10

viewing information about, 71

Raising image, 20 Rear-screen projection, 57, 81 to 82 Registration, 9

Index 95

Remote control

A/V Mute button, 28 as wireless mouse, 31 battery used, 84 connecting cable for mouse, 35 correcting color, 30 E-Zoom button, 29 Freeze button, 28 numeric keypad, using, 52 pointer tool, using, 32 problems, 77 range, 84 specifications, 84 switching sources, 27

troubleshooting, 77 Replacing lamp, 62 to 65 Request code, password, 53 Resetting lamp timer, 65 Resetting menu options, 45 Resize image, 30 Resolution, 30, 73, 83

Speaker, specifications, 83 Specifications

brightness, 83 dimensions, 84 electrical, 84 environmental, 85 general, 83 lamp, 84 remote control, 84 resolution, 83

safety, 85 Sports color mode, 30, 46 sRGB color mode, 30, 46 Startup screen, creating, 54 to 55 Startup screen, user’s logo, See User’s Logo Status lights, 69 to 70 Support, see Technical support S-video cable, 11, 38 Switching picture source, 17, 27 Sync setting, 49 Synchronization, adjusting, 23, 75 to 76

Safety

instructions, 89 to 90

specifications, 85 Saturation setting, 47 Screen

blank, 18 to 19

distance from projector, 14, 83

ordering, 11

startup screen, creating, 54 to 55 Screen image, See Image Security

Kensington lock, 11

password protection, 51 to 54 Sharpness setting, 47 Signal menu, 48 to 49 Six-axis color adjustment, 47 to 48 Sleep mode, 24 Sound, troubleshooting, 76, 77 Source

selecting, 17, 27

viewing, 71

96 Index

Technical support, 8, 78 to 79 Temperature

requirements, 85

status light, 69 to 70 Temperature, color, 47 Theatre color mode, 30, 46 Tint setting, 47 Tracking, adjusting, 23, 75 to 76 Transporting projector, 66 Troubleshooting

blank screen, 18 to 19, 72 to 73

cut-off image, 73 to 74

distorted image, 21 to 22

image and sound problems, 72 to 77

no signal, 18, 72 to 73

projector problems, 67 to 70

remote control problems, 77 Turning off picture (using A/V Mute), 28 Turning off projector, 23 to 24

Unpacking projector, 10 USB cable, 10, 35 User’s Logo menu, 54 to 55

VCR, connecting, 36 to 40 Video

cables, 10, 11, 36 connecting video equipment, 36 to 40 display settings, viewing, 71 formats, supported, 86 to 87

selecting source, 17, 27, 37, 38 Video Signal setting, 49 Volume, controlling, 29

Warning lights, 69 to 70 Warranty, 9 Windows

display problems, 73

resolution setting, 74 Wireless, mouse, 31, 35

Zoom ratio, 83 Zooming image, 21, 29

Index 97

Epson EX100 User Guide

Specifications and Main Features

Frequently Asked Questions

User Manual

Important Safety Information

Copyright Notice

Trademarks

Contents

Welcome

Using Your Documentation

Getting More Information

Registration and Warranty

Unpacking the Projector

Additional Components

Optional Accessories

Displaying and Adjusting the Image

Positioning the Projector

Projecting the Image

Turning On the Projector

Selecting the Image Source

Troubleshooting Display Problems

You Can’t Project an Image

The Projector and Notebook Don’t Display the Same Image

Adjusting the Image

Adjusting the Height of Your Image

Focusing and Zooming Your Image

Adjusting the Image Shape

Correcting Computer Images

Using the A/V Mute Slide

Shutting Down the Projector

Using the Direct Power On Function

Using the Remote Control

Using the Remote Control

Replacing the Batteries

Controlling the Picture and Sound

Switching Between Picture Sources

Turning Off the Picture and Sound

Stopping Action

Zooming Part of Your Image

Controlling the Volume

Resizing Video Images

Adjusting the Color Mode

Operating Your Computer with the Remote Control

Highlighting Your Presentation

Using the Pointer Tool

Customizing the Pointer Tool

Connecting to Computers and Other Equipment

Connecting to a Computer

Connecting to the Computer Port

Connecting the Cable for Remote Mouse Control

Connecting to Video Equipment

Connecting a Composite Video Source

Connecting an S-Video Source

Connecting a Component Video Source

Connecting an RGB Video Source

Playing Sound Through the Projector

Fine-Tuning the Projector

Using the Menu System

Restoring the Default Settings

Adjusting the Image

Six-Axis Color Adjustment

Adjusting Signal Settings

Customizing Projector Features

Using the Projector Security Features

Enabling Password Protection

Creating Your Own Startup Screen

Disabling the Projector’s Buttons

Customizing Power and Operation

Maintaining the Projector

Cleaning the Lens

Cleaning the Projector Case

Cleaning the Air Filter and Vent

Replacing the Lamp and Air Filter

Resetting the Lamp Timer

Transporting the Projector

Solving Problems

Using On-Screen Help

Checking Projector Status

What To Do When the Lights Flash

Viewing Lamp Usage and Other Information