Epson EPL-7500 Quick Reference Guide
EPSON AMERICA, INC.
Product Support Bulletin
Subject: How To Connect Epson PostScript Printers Into An AppleTalk Network
EPSON
Date: 10/9/92
Page(s): 1 of 1
PSB No: P-0092
Originator: SDS
This bulletin provides information on how to interface Epson laser printers with an
Epson PostScript’ Card to an Apple Macintosh2 using Apple LocalTalk3 and the
Bridgeport4 by Extended Systems.
Connecting a printer to an Apple Macintosh can be difficult if the printer does not
have an AppleTalk interface. The Epson Action Laser II and EPL-8000 laser
printers with the Epson PostScript Card installed do not have built-in AppleTalk
interfaces and as such can be difficult to connect to an AppleTalk network.
Extended Systems has a solution to this problem. It is the Bridgeport 2679B. This
printer sharing device allows you to connect a PostScript printer to an AppleTalk
network and two DOS-based PCs. The Bridgeport has an AppleTalk port that
allows connection to either a stand-alone Macintosh or to an AppleTalk network via
Apple LocalTalk. This device also has a serial and a parallel port for connecting
two DOS-based PCs. The Bridgeport will monitor each of the input ports and route
data that it receives to the printer.
The Bridgeport 26978 was tested from an AppleTalk network to an Action Laser II,
an EPL-8000 with the Epson PostScript Card, and to an Epson EPL-7500. All three
installations worked flawlessly and the printed output was exactly as expected. This
device requires that the Apple LaserWriter? driver Version 5.2 or above be installed
on the network.
The manufacturer suggested retail price of the Extended Systems’ Bridgeport is
$495.005Seebel
ow for Extended Systems’ address and telephone numbers.
Extended Systems
P.O. Box 4937
Boise, Idaho 83711
(800) 235-7576 (U.S.)
(406) 587-7575 (Outside U.S.)
’
PostScript is a registered trademark of Adobe Systems Incorporated.
’
Macintosh is a trademark of Apple Computer, Inc.
3
AppleTalk, LocalTalk, and LaserWriter are registered trademarks of Apple Computer, Inc.
’
Bridgeport is a trademark of Extended Systems Incorporated.
6
Price is subject to change without notice.
EPSON AMERICA, INC.
Product Support Bulletin
EPSON
Subject:
Date: 4/3/91
Page(s): 1 of 11
Epson printers issue beep tones and/or displays error codes when certain error
conditions exist. Those beeps or codes can assist you in locating and repairing
customer’s printers. The following error codes are listed by product name.
EPl-4000 Display Codes
PE
co
IL
IE
PJ
Laser & Non-impact Printer Error Codes
PSB No:
Originator: JV
Paper End (out) detected
Cover open
Ink low
Ink End (out)
Paper jam
P-0077
E1
E2
E4
E6
E7
E8 - YY (blinking)
E9 (blinking)
E0 (blinking)
bF
(blinking)
(blinking)
(blinking)
*-)
YY (blinking)
*--)
YY (blinking)
Heater error (broken heater wire)
Contact error (heater fan or thermistor contact)
C034 DVR board error
C034 Main board software Error I
(YY will be a number from 60(H) to 7D(H))
C034 Main board software Error II
(YY will be a number from 02(H) to XB(H))
Board contact error, C034 Main board hardware
(YY will be one of the following numbers: 80,81,84,85,
86,87,8A, 8C)
C034 Main board hardware error
Abnormal voltage
Buffer overflow for fonts
EPl-4000 cont.
PSB No: P-0077
Page: 2 of 11
bo
CE
PS
Lr
LE
dP
FF
EPL=6000 / ActionLaser / ActionLaser+ LCD Codes
CHANGE DRUM
COVER OPEN
Buffer overflow for graphics
Card error
Paper size error
Release lever error
Envelope lever error
Data processing
Depress the Form Feed button
The drum needs to be changed. The drum cartridge may
not be installed, the cartridge may not be installed
property or the cartridge may be defective.
Printer cover is open
CPU ERROR
ERROR 10
ERROR 11
ERROR 12
ERROR 20
ERROR 21
ERROR 22
ERROR 30
ERROR 31
ERROR 32
Printer’s CPU has made a calculation error
Program ROM error
Font cartridge or identity cartridge checksum error
RAM error
Memory overflow
Print overrun error
Receive
Memory error
Scanner error
Heater (Heat Roller Unit) error
buffer overflow
EPL-6000 cont.
PSB No: P-0077
Page: 3 of 11
ERROR 33
ERROR 40
FONT CARD ERROR
INSERTION ERROR
PAPER EMPTY
PAPER JAM
PAPER SIZE ERROR
PS CHANGE
Thermistor error
Parity / Framing error
Font cartridge is bad (or is not inserted) correctly
Paper is not inserted correctly or has jammed at the paper
tray
No paper in the paper cassette
Paper cassette is not installed properly
Paper cassette lid is open
Paper sensor is bad
Paper is jammed inside the printer
Paper setting does not match the size of the paper in the
paper cassette
Paper size requested by the host conflicts with the
SelecType setting
EPL-7000 LCD Codes
NOTE:
In some cases, the red CONTINUE light flashes when an error is detected.
This requires you to correct the problem and then press the CONTINUE
button to dear the error.
set to ON, some errors may clear automatically even though the problem
remains.
Status messages are preceded by [S], warning messages are preceded by
[W], and error messages are preceded by [E]. In some cases the message
you see on your display also shows the printer mode.
[E] ADD MEMORY FOR CH-X
The printer has insufficient memory available in the channel displayed.
[E] CARD MEMORY OVERFLOW
This message indicates that the combined memory requirement of the cards in
slots A and B exceeds 4 Mbytes.
However, if the
AUTO CONT
option in SelecType is
EPL-7000 cont.
[S] COPY END X/X
Multiple-copy printing is cancelled (you pressed the COPY END button when
the printer was off line).
[E] COVER OPEN
The printer cover is open or the imaging cartridge is not installed.
[S] DATA
The printer has received data but is not yet printing, or the printer has received
data and is off line.
[E] FEED JAM
Paper is not feeding into the printer from the specified cassette or has jammed
on its way into the printer.
PSB No: P-0077
Page: 4 of 11
[S] GRAPHIC DRAWING
Graphics are being created.
[E] ILLEGAL CARD
A card or cartridge in a particular slot cannot be read.
[S] INITIALIZE
The printer is being initialized (reset) to the factory settings.
[E] INSUFF. MEMORY
The printer has insufficient memory available for the task you have given it.
This error can also be cleared by turning the printer off and back on again.
However, it may be necessary to simplify the page you are trying to print or
add more memory to the printer.
[E] PAGE BUFFER FULL
Text or graphics data has filled the printer’s buffer and an incomplete page is
ejected.
[S] PAPER FEEDING
The printer is feeding paper.
[E] PAPER JAM
Paper is not being fed into the printer or paper is jammed inside the paper
path.
EPL-7000 cont.
[E] PAPER OUT
There is no paper in the standard paper cassette and the optional lower paper
cassette (ii installed). Or, the paper set lever is in the manual position and you
are not feeding pages correctly.
[E] PAPER OUT SET AUTO XXX
There is no paper in any of the paper cassettes. The right column of the
display prompts you to load the correct paper size into the paper cassette.
[E] PAPER OUT SET OPT XXX
There is no paper in the optional lower paper cassette. The right column of
the display prompts you to load the correct paper size into the paper tray of
the lower paper cassette.
[E] PAPER OUT SET STD XXX
There is no paper in the standard paper cassette. The right column of the
display prompts you to load the correct paper size into the standard paper
cassette.
PSB No: P-0077
Page: 5 of 11
[E] PAPER SIZE ERROR
The paper size you selected with SelecType (or the default size if you have not
selected a size) does not match the paper loaded in the selected paper
cassette.
[S] PRINTING
The printer has received data and is printing..
[S] PRINT STOP X/X
The printer stops printing during a multi-copy print operation.
[S]
[S] READY
[E] REINSERT CARD
RAM Check X.X MB
The printer is checking RAM (X.X = capacity).
The printer is ready to print.
If this message appears on the display, you may have removed a font card or
cartridge while the FEED light was still lit or while the printer was on line.
EPL-7000 cont.
[E] REMOVE CARD
You may have inserted a font card or cartridge while the printer was on line or
while the FEED light was on. Data still remains in the printer’s buffer.
[E] RESELECT TRAY
The optional lower paper cassette is not installed and the INPUT option is set
to OPT or AUTO.
[S] RESET
The printer is being reset to the previous settings in the macro specified with
LOAD MACRO option in SelecType Level 1.
[S] ROM Check
The printer is checking ROM.
PSB No: P-0077
Page: 6 of 11
[E] SAVE MEMORY OVERFLOW
If this message appears when you are trying to save a macro with the SAVE
MACRO option in SelecType Level 1, the printer does not have enough
memory to save any additional macros
[E] SERVICE REQ. CXXX
A controller error has been detected.
[E] SERVICE REQ. EOOXX
A print engine error has been detected.
XX=
[E] SET FULL PRINT
This message may appear when you are trying to print graphics or a mix of
text and graphics.
[S] STANDBY MODE
When both CH P and CH S remain off for about thirty minutes, the printer
enters standby mode and this message appears.
03 Fusing Unit (low temp)
04 Main Drive Motor
05 Ozone Fan motor
06 Polygon Mirror Drive
09 HSync Signal
[E] STARTUP ERROR
If this message appears when you turn on the printer, the power may have
been turned off while the printer was performing a save or reset operation.
EPL-7000 cont.
[W] TONER LOW
The printer is almost out of toner. When this message first appears on the
LCD display, you can print up to 25 more pages.
[E] TONER OUT
The imaging cartridge must be replaced.
[E] TRAY SET AUTO XXX
The paper size setting does not match the paper loaded in the specified paper
cassette. The right column is the expected paper size and the currently
selected cassette.
[E] TRAY SET OPT XXX
The paper size setting does not match the paper loaded in the optional lower
paper cassette. The right column is the expected paper size.
PSB No: P-0077
Page: 7 of 11
[E] TRAY SET STD XXX
The paper size setting does not match the paper loaded in the standard paper
cassette. The right column is the expected paper size.
[S] WAlT
Printer is being reset after a START UP ERROR.
[S] WARMING UP
Printer is warming up.
EPL-7500
[E] COVER OPEN
Cover is open or the imaging cartridge is not installed.
[E] MANUAL FEED
Manual feed method is selected.
[S] OFF LINE
Printer is Off tine
[E] OUT OF PAPER
No paper cassette is installed, the paper cassette is empty, or the paper set
lever is in the manual position.
Loading...