Epson EB-L1070W, EB-L1070U, EB-L1070, EB-L1050U, EB-L1060W User Manual

...

User's Guide

Notations Used in This Guide

• Safety indications

The documentation and the projector use graphical symbols to show how to use the projector safely. The indications and their meaning are as follows. Make sure you understand them properly before reading the guide.

Warning

Caution

• General information indications

Attention

s Indicates a page where detailed information regarding a topic can be found.

[Name] Indicates the name of the buttons on the remote control or the control panel.

Menu Name Indicates Configuration menu items.

This symbol indicates information that, if ignored, could possibly result in personal injury or even death due to incorrect handling.

This symbol indicates information that, if ignored, could possibly result in personal injury or physical damage due to incorrect handling.

Indicates procedures which may result in damage or injury if sufficient care is not taken.

Indicates additional information and points which may be useful to know regarding a topic.

Example: [Esc] button

Example: Select Brightness from Image. Image - Brightness

Safety Warning and Cautions

Make sure you read the following before you use the projector.

Safety Instructions

Warning and Cautions on Installation

An optional ceiling mount is required when suspending the projector from a ceiling.

"Optional Accessories" p.233

Warning

• Do not use or install the projector where it may be subject to water or rain, or high humidity, such as outdoors, in a bathroom, or shower room, and so on. Otherwise, it could cause a fire or electric shock.

• Do not install in locations where salt damage could occur, or in locations subject to corrosive gas such as sulphuric gas from hot springs. Otherwise, corrosion could cause the projector to fall. It could also cause the projector to malfunction.

• A special method of installation is required when suspending the projector from a ceiling (ceiling mount). If installation work is not carried out correctly, the projector could fall down. This may result in injury or accidents. Contact your local dealer or the nearest address provided in the Epson Projector Contact List. s Epson Projector Contact List

• Failure to install the ceiling mount and projector may cause the projector to fall. After installing the specific Epson mount that supports your projector, make sure you secure the projector and the mount using wire that is strong enough to hold their weight.

• If you use adhesives on the ceiling mount fixing points to prevent the screws from loosening, or if you use things such as lubricants or oils on the projector, the projector case may crack causing it to fall from its ceiling mount. This could cause an accident or injury to anyone under the ceiling mount. When installing or adjusting the ceiling mount, do not use adhesives, lubricants, oils, and so on to prevent the screws from loosening.

Warning

• Do not install the projector in locations subject to high humidity or dust, or locations subject to oil or steam, such as kitchen counters, kitchens, or near humidifiers. Otherwise, electric shock or fire could occur. Also, oily particles in the air could cause the projector case to deteriorate causing the projector to fall from the mount if it is suspended from a ceiling.

• Do not cover the projector's air intake vent or air exhaust vent. If either of the vents are covered, the internal temperature could rise and cause a fire.

• Do not place flammable objects in front of the lens. If you set the schedule to turn on the projector automatically, any flammable objects placed in front of the lens could cause a fire.

• Do not tie the power cord and other connection cables together. Otherwise, it could cause a fire.

• Only use the specified power-supply voltage. Otherwise, it could cause a fire or electric shock.

Safety Warning and Cautions

Warning

• Be careful when handling the power cord. Otherwise, it could cause a fire or electric shock. Note the following when handling the power cord.

- Do not plug multiple power cords in a single electric outlet.

- Do not plug in the power cord if there are any foreign substances, such as dust, stuck to it.

- Make sure you insert the power cord all the way in.

- Do not plug in or unplug the power cord with wet hands.

- Do not pull the cord when unplugging the power cord. Make sure you hold it by the plug.

• Do not use a damaged power cord. Otherwise, it could cause a fire or electric shock. Note the following when handling the power cord.

- Do not alter the power cord.

- Do not place any heavy objects on the power cord.

- Do not bend, twist, or pull the power cord forcibly.

- Do not layout the power cord near a heating device.

Attention

• Do not install the projector in a location that is subject to vibration or shock.

• Do not install the projector near a high-voltage line or object that generates magnetism. Otherwise the projector may not work correctly.

• Do not use or store the projector in a location that is subject to extreme temperatures. Also, avoid sudden temperature changes.

Make sure you maintain the operating or storage temperature ranges. s “Projector General Specifications” p.279

• When installing the projector in an environment in which a high-powered laser beam is being used, make sure it is installed so that the laser beam does not hit the surface of the projection lens.

• When using at an altitude that exceeds 1,500 m, set High Altitude Mode to On. s Extended - Operation - High Altitude Mode p.146

• The projector can be installed at any angle. There is no vertical or horizontal limit to how the projector can be installed.

Caution

Do not place the projector on an unstable surface, such as on an unstable table or tilted surface. When projecting vertically, install the projector appropriately to prevent the projector from falling. Otherwise it may cause an injury.

• You may need dedicated installation mounts to tilt and install the projector. Contact a professional and prepare the mount.

• Plan so that the mount does not fall.

Safety Warning and Cautions

Attention

• Make sure you secure the following space around the projector so as not to block the air exhaust vent and the air intake vent.

• When setting up multiple projectors, make sure there is a gap of at least 70 cm between the projectors. Also, make sure that the heat from the air exhaust vent does not go into the air intake vent.

Attention

• Do not stack projectors directly on top of each other.

• When using the ceiling mount or the portrait mount, use commercially

available M6 screws (up to a depth of 14 mm) to fix the projector's ceiling mount fixing points and the mount at four points.

• Secure the following space when placing a partition between projectors.

• We recommend setting the focus, zoom, and lens shift at least 20 minutes after you start the projection, because images are not stable right after turning on the projector.

• When adjusting the image height with the vertical lens shift, adjust by moving the image from the bottom to the top. If it is adjusted from the top to the bottom, the image position may move down slightly after adjusting.

Safety Warning and Cautions

Warning and Cautions on Usage

Warning

• Do not cover the projector's air intake vent or air exhaust vent. If either of the vents is covered, the internal temperature could rise and cause a fire.

• Do not look into the lens while projecting. The powerful light emitted could cause damage to eyesight. Take particular care when there are children present. When turning on the projector at a distance using the remote control, make sure there is no one looking into the lens.

• During projection, do not block the light from the projector with the lens cover (removable) or a book and so on.

If the light from the projector is blocked, the area on which the light shines becomes hot which could cause it to melt, burn, or start a fire. Also, the lens may get hot due to the reflected light which could cause the projector to malfunction. To stop projection, use the A/V Mute function, or turn off the projector.

• Do not open the projector's case. Never disassemble or remodel the projector. There are high-voltage components inside the projector that could cause fire, electric shock, or an accident.

• If an error occurs, disconnect the power cord from the electrical outlet, and contact your local dealer or the nearest address provided in the Epson Projector Contact List. If you continue using the projector as it is, it could cause an electric shock, fire, or even damage to eyesight.

s Epson Projector Contact List

Attention

• Only remove the lens unit when necessary. If dust or dirt enter the projector, projection quality deteriorates and it could cause a malfunction.

• Try not to touch the lens section with your hand or fingers. If fingerprints or oils are left on the surface of the lens, projection quality deteriorates.

• If you continue to project while the surface of the lens is dirty, projection quality deteriorates. Make sure you clean the lens. s “Cleaning the Lens”

p.204

• Store the projector with the lens unit installed. If the projector is stored without the lens unit, dust and dirt may get inside the projector and cause malfunctions or lower the quality of projection.

• When storing, make sure you remove the batteries from the remote control. If the batteries are left in the remote control for an extended period of time, they may leak.

Caution

Do not place objects that may become warped or otherwise affected by heat near the air exhaust vent and do not put your face or hands near the vent while projection is in progress.

Safety Warning and Cautions

• About the LCD panel

- The LCD panel may contain pixels that are missing or appear bright all the time. This is not a sign of an error.

- When a high-powered laser beams through the surface of the projection lens even when it is not being used, it can cause a malfunction in the LCD panel. Attach the lens cover when storing the projector.

• About the light source The projector uses a laser as the light source. The laser has the

following characteristics.

- Depending on the surroundings, the brightness of the light source may decline. The brightness declines a lot when the temperature gets too high.

- The brightness of the light source declines the longer it is used. You can change the relationship between usage time and decline in brightness in Brightness Settings.

s "Relationship between Brightness Level and light source operation time" p.78

• About Light Source Calibration

-When Run Periodically is set to On for Light Source Calibration, every time the usage time reaches 100 hours, calibration starts automatically for the light source when the projector is turned off. However, this does not start automatically when the projector is used continuously for more than 24 hours, or when direct shutdown is used regularly. Set Light Source Calibration in the scheduling function.

s "Scheduling Function" p.112

- When performing Light Source Calibration, the difference between the white balance and the brightness level for the light source is corrected.

s Reset - Light Source Calibration - Run Periodically p.162

Warning and Cautions on the Laser

Warning

• Laser warning labels are attached inside the projector and on the side of the projector.

Inside

Side

Warning

• Do not open the projector's case. The projector contains a high-powered laser.

• Do not look into the lazer beam being emitted from the projection lens while projecting. (Based on the RG2 IEC/EN 62471-5: 2015)

• This projector may become RG3 when an interchangeable lens with a throw ratio greater than 3.5 is installed. See the manual for the lens list and hazardous distances before operation. Such combinations of projector and lens are intended for professional use only, and are not intended for consumer use.

Safety Warning and Cautions

Caution

• This projector is a Class 1 laser product that complies with the IEC/ EN60825-1: 2014 international standard for lasers.

• Do not disassemble the projector when disposing of it. Dispose according to your local or national laws and regulations.

Notes on Transporting

There are many glass parts and precision components inside the projector. To prevent damage due to impacts when transporting, handle the projector as follows.

Caution

The projector should not be carried by one person. At least two people are needed to unpack or carry the projector.

Attention

• Moving Nearby

- Turn off the power to the projector and disconnect all cables.

- Attach the cover to the lens.

• When Transporting After checking the points in "Moving Nearby", prepare the following and then pack up the projector.

- Remove the lens unit if an option lens is installed.

- If the projector does not have a lens, attach the cover that was on the lens mount when you purchased the projector.

- Attach the lens if the projector has a built-in lens. Upon purchase, attach the protective pad that is attached around the lens unit.

- Move the lens position to the home position. s "Adjusting the Position of the Projected Image (Lens Shift Adjustment)" p.34

- Enclose the projector securely in packaging material to protect it from shock, and place it into a strong container. Be sure to notify the carrier company that it is precision equipment and that it needs to be kept horizontally during transportation.

Notations Used in This Guide ........................ 2

Introduction

Part Names and Functions .................................. 15

Front/Top...................................................15

Rear .......................................................16

Connector Ports ..............................................17

Base ...................................................... 18

Control Panel ................................................18

Remote Control...............................................20

Handy remote control operations................................ 22

Replacing the remote control batteries ............................. 23

Remote control operating range................................. 24

Connecting a cable to the remote control ........................... 24

Preparing the Projector

Installing the Projector ..................................... 27

Removing and Attaching the Projector Lens Unit ........................ 27

Attaching................................................. 27

Lens Calibration............................................29

Removing .................................................30

Installation Settings ............................................ 31

Changing the direction of the image (projection mode).................31

Screen Settings ............................................... 32

Adjusting the position of the image on the projected screen ..............32

Displaying the Test Pattern ....................................... 33

Adjusting the Position of the Projected Image (Lens Shift Adjustment).........34

Adjusting the Image Size ........................................ 37

Correcting the Focus........................................... 38

Correcting Distortion (Image Warping).............................38

Registering and Loading Lens Adjustment Values.......................39

Adjusting the Height of the Projected Image (for Normal Installment).......... 41

Adjusting the Horizontal Tilt (for Normal Installment).....................42

ID Settings..................................................42

Set the projector ID..........................................42

Checking the projector ID ...................................... 43

Setting the remote control ID................................... 43

Setting the Time ..............................................44

Other Settings................................................45

Settings related to basic operations............................... 45

Settings related to display ......................................46

Connecting Equipment ..................................... 47

Connecting a Computer......................................... 47

Connecting Image Sources.......................................49

Connecting External Equipment...................................51

Connecting a LAN Cable......................................... 52

Connecting an HDBaseT Transmitter................................ 53

Installing the Wireless LAN Unit .................................... 54

Attaching the Cable Cover.......................................55

Attaching................................................. 55

Basic Usage

Turning On the Projector ................................... 58

Home Screen ................................................59

Turning Off the Projector ................................... 60

Projecting Images ......................................... 61

Automatically Detecting Input Signals and Changing the Projected Image (Source

Search) ....................................................61

Switching to the Target Image by Remote Control.......................62

Adjusting the Volume..........................................63

Adjusting the Projected Images ............................. 64

Correcting Distortion in the Projected Image ...........................64

H/V-Keystone ..............................................65

Quick Corner...............................................66

Curved Surface.............................................67

Corner Wall ................................................ 71

Contents

Point Correction............................................ 74

Selecting the Projection Quality (Selecting Color Mode)...................76

Setting the Brightness ..........................................77

Guide to Estimated Remains .................................... 78

Relationship between Brightness Level and light source operation time......78

Setting the Amount of Light of the Projected Image ......................79

Changing the Aspect Ratio of the Projected Image.......................80

Changing methods.......................................... 80

Adjusting the Image ...........................................81

Hue, Saturation, and Brightness adjustment .........................81

Gamma adjustment.......................................... 82

Adjusting Image Resolution (Image Enhancement) .......................83

4K Enhancement (EB-L1075U/EB-L1070U/EB-L1065U/EB-L1060U/EB-L1050U

only) ....................................................83

Image Preset Mode.......................................... 84

Frame Interpolation ..........................................85

Noise Reduction ............................................86

MPEG Noise Reduction ........................................86

Super-resolution ............................................ 87

Detail Enhancement .........................................87

Projecting 3D Images ...........................................87

Useful Functions

Multi-Projection Function . ................................. 90

Adjustment Procedure.......................................... 90

Advance preparation ......................................... 90

Adjusting the projected position.................................90

Adjusting the projected images.................................. 90

Tiling ......................................................90

Edge Blending ...............................................91

Black Level .................................................. 93

Color Matching............................................... 96

Displaying a Scaled Image .......................................97

Input Sources for Split Screen Projection ............................99

Operating procedures ....................................... 100

Restrictions during split screen projection..........................102

Hiding the Image and Sound Temporarily (A/V Mute) .................... 102

Freezing the Image (Freeze)..................................... 103

Enlarging Part of the Image (E-Zoom)............................... 104

Saving a User's Logo ........................................... 104

Content Playback Feature ................................. 106

Switching to Content Playback Mode ............................... 106

Playing a Playlist ............................................. 106

Adding Effects to Images (Effect Feature) ............................ 107

Restrictions on Content Playback Mode............................. 108

Memory Function ......................................... 110

Saving/Loading/Erasing/Resetting the Memory........................ 110

Scheduling Function ...................................... 112

Saving an Event..............................................112

Setting an Event ........................................... 112

Checking an Event.......................................... 113

Editing an Event ........................................... 113

Security Functions ........................................ 115

Managing Users (Password Protection).............................. 115

Kinds of Password Protection.................................. 115

Setting Password Protection................................... 115

Entering the password....................................... 116

Restricting Operation.......................................... 117

Control Panel Lock ..........................................117

Lens Lock ................................................ 118

Remote control button lock....................................118

Anti Theft/Fall Prevention ....................................... 119

Projection Functions ....................................... 99

Projecting Two Images Simultaneously (Split Screen)..................... 99

Contents

Using the Projector on a Network

Wired Network Projection ................................. 121

Selecting Wired Network Settings................................. 121

Wireless Network Projection . . ............................. 124

Selecting Wireless Network Settings Manually ......................... 124

Selecting Wireless Network Settings in Windows ....................... 127

Selecting Wireless Network Settings in Mac........................... 127

Setting Up Wireless Network Security ............................... 127

Supported Client and CA Certificates............................. 129

Using a QR Code to Connect a Mobile Device .......................... 130

Using a USB Key to Connect a Windows Computer ...................... 131

Secure HTTP ............................................. 132

Importing a Web Server Certificate Using the Menus .....................132

Supported Web Server Certificates ...............................133

Setting a certificate using a Web browser .......................... 133

Configuration Menu

Configuration Menu Operations ........................... 136

List of Functions .......................................... 137

Configuration Menu Table...................................... 137

Network menu............................................ 138

Image Menu................................................ 140

Signal Menu ................................................ 142

Settings Menu ...............................................143

Extended Menu ..............................................146

Network Menu .............................................. 151

Notes on operating the Network menu ............................ 152

Soft keyboard operations ..................................... 152

Basic menu............................................... 153

Wireless LAN menu......................................... 154

Wired LAN menu ........................................... 157

Notifications menu ......................................... 158

Others menu ..............................................159

Reset menu ............................................... 160

Info Menu (Display Only)........................................161

Reset Menu.................................................162

Batch Setup .............................................. 164

Setup Using a USB Flash Drive .................................... 165

Saving settings to the USB flash drive ............................. 165

Reflecting saved settings to other projectors ........................ 167

Setup by Connecting the Computer and Projector with a USB Cable . . . . . . . . . . 168

Saving settings to a computer.................................. 168

Reflecting saved settings to other projectors ........................ 169

When Setup Fails .............................................171

Troubleshooting

Using the Help ........................................... 173

Reading the Indicators . . . . . . .............................. 175

Reading the Status Display ................................ 182

Explanations of the Display Content................................183

Problem Solving .......................................... 190

Problems Relating to Images ..................................... 191

No images appear .......................................... 191

Moving images are not displayed................................191

Projection stops automatically ..................................192

Not supported is displayed.................................... 192

No Signal is displayed........................................192

Images are fuzzy, out of focus, or distorted......................... 193

Interference or distortion appear in images ......................... 193

The image is truncated (large) or small, the aspect is not suitable, or the image has

been reversed .............................................194

Image colors are not right ..................................... 195

Images appear dark ......................................... 195

Problems when Projection Starts .................................. 196

The projector does not turn on................................. 196

Contents

Problems with Content Playback Mode ..............................197

Cannot play the playlist ...................................... 197

Other Problems.............................................. 197

There are afterimages (screen burn-in) in the projected image............ 197

No sound can be heard or the sound is faint ........................ 198

The remote control does not work ............................... 198

Nothing appears on the external monitor .......................... 199

I want to change the language for messages and menus ................ 199

Email is not received even if a problem occurs in the projector............ 200

The battery that saves your clock settings is running low. is displayed ....... 200

About Event ID ........................................... 201

Maintenance

Cleaning the Parts ........................................ 204

Cleaning the Projector ......................................... 204

Cleaning the Lens............................................ 204

Cleaning the Air Filter and Air Intake Vent ............................ 204

Cleaning the air filter ........................................ 205

Cleaning the air intake vent ....................................206

Replacing Consumables ................................... 208

Replacing the Air Filter......................................... 208

Air filter replacement period ................................... 208

Replacing the air filter........................................208

Image Maintenance ....................................... 210

Panel Alignment ............................................. 210

Color Uniformity............................................. 212

Appendix

Monitoring and Controlling ............................... 215

Epson Projector Management .................................... 215

Changing Settings Using a Web Browser (Epson Web Control).............. 215

Displaying the Epson Web Control Screen..........................215

Basic Control Screen .........................................216

OSD Control Pad Screen...................................... 217

Lens Control Screen......................................... 218

Status Information Screen..................................... 220

Changing Settings Using a Web Browser (Content Playback Mode)...........220

Remote ................................................. 222

Playlists................................................. 223

USB Memory Device.........................................223

Time Table............................................... 224

OSD Control Pad........................................... 224

Using the Mail Notification Function to Report Problems.................. 225

Reading error notification mail .................................. 225

Management Using SNMP ...................................... 226

ESC/VP21 Commands ..........................................226

Command list............................................. 226

Cable layouts ............................................. 226

About PJLink................................................227

About Crestron Connected

Operating a projector from your computer ......................... 228

About Web API.............................................. 232

..................................... 228

Optional Accessories and Consumables .................... 233

Optional Accessories.......................................... 233

Consumables............................................... 233

Screen Size and Projection Distance ........................ 234

Projection Distances for EB-L1075U/EB-L1070U/EB-L1065U/EB-L1060U/EB-L1050U/

EB-L1070W/EB-L1060W . ....................................... 234

ELPLM08 ................................................ 234

ELPLX01/ELPLX01W ......................................... 235

ELPLU03.................................................236

ELPLU04/ELPLU02.......................................... 237

ELPLW05................................................ 238

ELPLW06/ELPLW04......................................... 239

ELPLW08................................................ 240

ELPLM15/ELPLM09/ELPLS04................................... 241

ELPLM10/ELPLM06......................................... 242

ELPLM11/ELPLM07......................................... 243

Contents

ELPLL08/ELPLL07...........................................244

ELPLR04................................................. 245

Projection Distances for EB-L1070 . . ............................... 247

ELPLM08 ................................................ 247

ELPLX01/ELPLX01W .........................................248

ELPLU03.................................................249

ELPLU04/ELPLU02.......................................... 250

ELPLW05................................................ 251

ELPLW06/ELPLW04......................................... 252

ELPLW08................................................ 253

ELPLM15/ELPLM09/ELPLS04................................... 254

ELPLM10/ELPLM06......................................... 255

ELPLM11/ELPLM07......................................... 256

ELPLL08/ELPLL07...........................................257

ELPLR04................................................. 258

Polarizer (ELPPL01) Installation Distance ............................. 259

EB-L1075U/EB-L1070U/EB-L1065U/EB-L1060U/EB-L1050U . . . . . ..........259

EB-L1070W/EB-L1060W ...................................... 259

EB-L1070 ................................................ 259

Adjustment Range for Projected Images .................... 261

H/V-Keystone ............................................... 261

Curved Surface.............................................. 261

Corner Wall .................................................268

Trademarks and Copyrights......................................285

List of Safety Symbols . . . . ................................. 287

Index .................................................... 289

Supported Monitor Displays ............................... 274

Supported Monitor Displays ..................................... 274

PC ..................................................... 274

SD ..................................................... 276

HD .....................................................276

4K (EB-L1075U/EB-L1070U/EB-L1065U/EB-L1060U/EB-L1050U only) . . . . .... 277

Specifications ............................................ 279

Projector General Specifications ...................................279

Appearance .............................................. 284

General Notes ............................................ 285

About Notations ............................................. 285

Introduction

This chapter explains the names for each part.

Part Names and Functions

The illustrations in this guide show the lens unit attached to the projector.

Front/Top

Name Function

Projection lens

Remote Receiver

Status indicators

Air intake vent

(air filter)

Images are projected through here.

Warning

Do not look into the lens while projecting. This could cause damage to eyesight due to the power‐ ful light emitted.

Caution

When shifting the lens, do not put your hands near the lens unit. Your fingers may get caught between the lens unit and the projector, and cause an in‐ jury.

Receives signals from the remote control.

The color of the indicators and whether they are flashing or lit indicate the status of the projector.

s "Reading the Indicators" p.175

Takes in air to cool the projector internally. s "Cleaning the Air Filter and Air Intake Vent" p.204

Air intake vent

Name Function

Takes in air to cool the projector internally.

USB-A port

Wireless LAN indicator

Cable cover

• Allows you to install the optional wireless LAN unit and connect the projector to the network.

• Allows you to connect a commercially available USB flash drive and play the playlist in Content Playback mode.

Indicates the access status to the optional wireless LAN unit.

s "Optional Accessories and Consumables" p.233

Cover for the port connectors section at the rear to protect connected cables.

s "Attaching the Cable Cover" p.55

Part Names and Functions

Name Function

Lens replacement

cover

Air exhaust vent

Remove when attaching or removing the lens. s "Removing and Attaching the Projector Lens Unit"

p.27

Caution

When moving the projector, do not hold the lens replacement cover. The lens replacement cover may be removed and the projector may fall, which could cause an injury.

Exhaust vent for air used to cool the projector internally.

Caution

While projecting, do not put your face or hands near the air exhaust vent, and do not place objects that may become warped or damaged by heat near the vent. Hot air from the air exhaust vent could cause burns, warping, or accidents to occur.

Rear

Power inlet

Control panel

Security slot

Name Function

Connects the power cord to the projector.

s "Control Panel" p.18

The security slot is compatible with the Microsaver Security System manufactured by Kensington.

s "Anti Theft/Fall Prevention" p.119

Connector Ports

s "Connector Ports" p.17

Part Names and Functions

Connector Ports

Name Function

BNC port

Computer Port

Audio3 port

For analog RGB signals from a computer and component video signals from other video sources.

Inputs audio from equipment connected to the HDMI port or the DVI-D port.

Cable holder

RS-232C port

Remote port

Service port

HDMI port

DVI-D port

HDBaseT port

LAN port

Name Function

Run a commercially available cable tie to secure cables.

When controlling the projector from a computer, connect it to the computer with an RS-232C cable. This port is for control use and should not normally be used.

s "ESC/VP21 Commands" p.226

Connects the optional remote control cable set and inputs signals from the remote control. When the remote control cable is plugged into the Remote port, the remote receiver on the projector is disabled.

s "Optional Accessories and Consumables" p.233

This is used for batch settings. This port is for control use and should not normally be used.

s "Batch Setup" p.164

Inputs video signals from HDMI compatible video equipment and computers.

Inputs the computer DVI-D signals.

Connects a LAN cable to the optional HDBaseT Transmitter.

s "Connecting an HDBaseT Transmitter" p.53 s "Optional Accessories and Consumables" p.233

Connects a LAN cable to connect to a network.

Audio1 port

Monitor Out port

Audio Out port

Audio2 port

Inputs audio from equipment connected to the Computer port.

Outputs to an external monitor the analog signal from the computer connected to the Computer port or the BNC port. You cannot output signals input from other ports or component video signals.

Outputs audio from the currently projected image to an external speaker.

Inputs audio from equipment connected to the BNC port.

Part Names and Functions

Base

Name Function

Screw holes to fix the

cable cover

Air filter cover fixing

screw

Ceiling mount fixing

points (ELPMB47/ ELPMB48, 4 points)

Ceiling mount fixing

points (ELPMB22, 4 points)

Control Panel

Screw holes to fix the cable cover in place. s "Attaching the Cable Cover" p.55

Screws to fix the air filter cover in place.

Attach the optional ceiling mount here when suspending the projector from a ceiling.

s "Installing the Projector" p.27 s "Optional Accessories and Consumables" p.233

Name Function

Front feet

Rear feet

Security cable

installation point

When setup on a surface such as a desk, extend and retract the feet to adjust the height or tilt of the image.

s "Adjusting the Height of the Projected Image (for Normal Installment)" p.41

s "Adjusting the Horizontal Tilt (for Normal Installment)" p.42

Pass a commercially available anti-theft wire lock or a wire to prevent the projector from falling through here and lock it in place.

s "Anti Theft/Fall Prevention" p.119

[ ] button

[Source Search]

button

[Menu] button

Name Function

Turns the projector on.

Changes to the next input source that is sending an image. s "Automatically Detecting Input Signals and Changing

the Projected Image (Source Search)" p.61

Displays and closes the Configuration menu. s "Configuration Menu Operations" p.136

Part Names and Functions

Name Function

[ ] button

[ ]/[ ] buttons

[A/V Mute] button

• When the Configuration menu or the Help screen is displayed, it accepts and enters the current selection and moves to the next level.

• If pressed while projecting analog RGB signals from the Computer port or the BNC port, you can automatically optimize Tracking, Sync., and Position.

• Displays the Control Panel Lock screen allowing you to make settings to lock the control panel buttons.

"Restricting Operation" p.117

• If pressed when the Configuration menu or the Help screen is displayed, this button selects menu items and setting values.

s "Configuration Menu Operations" p.136 s "Using the Help" p.173

• Displays a test pattern.

s "Displaying the Test Pattern" p.33

• If pressed when the Configuration menu or the Help screen is displayed, this button selects menu items and setting values.

s "Configuration Menu Operations" p.136 s "Using the Help" p.173

Turns the video and audio on or off. s "Hiding the Image and Sound Temporarily (A/V

Mute)" p.102

Name Function

[ ]/[ ] buttons

[Esc] button

[t] button

• Displays the Info menu from the Configuration menu.

s "Info Menu (Display Only)" p.161

• If pressed when the Configuration menu or the Help screen is displayed, this button selects menu items and setting values.

s "Configuration Menu Operations" p.136 s "Using the Help" p.173

• Performs screen adjustments using the settings in Geometry Correction from the Configuration menu. s Settings - Geometry Correction p.143

• If pressed when the Configuration menu or the Help screen is displayed, this button selects menu items and setting values.

s "Configuration Menu Operations" p.136 s "Using the Help" p.173

• Stops the current function.

• If pressed when the Configuration menu is displayed, it

moves to the previous menu level. s "Configuration Menu Operations" p.136

Turns the projector off.

[Lens] button

Displays the adjustment screens for lens shift, zoom, focus, and distortion in that order each time the button is pressed.

If pressed for more than three seconds, the lens position moves to the home position.

Part Names and Functions

Remote Control

Name Function

[ ] button

[t] button

Change input buttons

[Aspect] button

[Auto] button

[Freeze] button

[Test Pattern] button

[Lens Shift] button

Turns the projector on.

Turns the projector off.

Changes to images from each input port. s "Switching to the Target Image by Remote Control"

p.62

The [SDI] button is unavailable.

Each time the button is pressed, the aspect mode changes. s "Changing the Aspect Ratio of the Projected Image"

p.80

If pressed while projecting analog RGB signals from the Computer port or the BNC port, you can automatically optimize Tracking, Sync., and Position.

Images are paused or unpaused. s "Freezing the Image (Freeze)" p.103

Displays a test pattern. s "Displaying the Test Pattern" p.33

Press to adjust the lens shift. s "Adjusting the Position of the Projected Image (Lens

Shift Adjustment)" p.34 If pressed for more than three seconds, the lens position

moves to the home position.

[Zoom] button

[Menu] button

Press to adjust the zoom. s "Adjusting the Image Size" p.37

Displays and closes the Configuration menu. s "Configuration Menu Operations" p.136

Part Names and Functions

Name Function

[ ][ ][ ][ ] buttons

[ ] button

[A/V Mute] button

[Page] buttons

[[][]]

[Volume] buttons

[a][b]

[ ] button

[User1] button

[User2] button [User3] button

• Press to adjust focus, zoom, distortion, and lens shift.

s "Adjusting the Position of the Projected Image (Lens Shift Adjustment)" p.34

s "Adjusting the Image Size" p.37 s "Correcting the Focus" p.38

• When the Configuration menu or the Help screen is displayed, pressing these buttons selects menu items and setting values. s "Configuration Menu Operations" p.136

When the Configuration menu or the Help screen is displayed, it accepts and enters the current selection and moves to the next level.

s "Configuration Menu Operations" p.136

Turns the video and audio on or off. s "Hiding the Image and Sound Temporarily (A/V

Mute)" p.102

• Press to change the test pattern while a test pattern is displayed.

• Moves to the previous or next image file when projecting images from a computer connected via a network.

[a] decreases the volume. [b] increases the volume.

"Adjusting the Volume" p.63

Displays the Info menu from the Configuration menu. s "Info Menu (Display Only)" p.161

Select any frequently used item from the Configuration menu items, and assign it to any of these buttons. By pressing the button, the assigned menu item selection/ adjustment screen is displayed, allowing you to make onetouch settings/adjustments.

s "Settings Menu" p.143

Name Function

Numeric buttons

[ID] button

[ID] switch

Remote port

[ ] button

[Num] button

[Geometry] button

[Memory] button

[E-Zoom] buttons

[z][x]

• Enter the Password.

s "Setting Password Protection" p.115

• Use this button to enter numbers in Network settings from the Configuration menu.

Hold down this button and press the numeric buttons to select the ID for the projector you want to operate using the remote control.

s "ID Settings" p.42

Use this switch to enable (On)/disable (Off) ID settings for the remote control.

s "ID Settings" p.42

Connects the optional remote control cable set and outputs signals from the remote control.

s "Optional Accessories" p.233 When the remote control cable is plugged into this remote

port, the remote control light-emitting is disabled.

Displays and closes the Home screen. s "Home Screen" p.59

Hold down this button and press the numeric buttons to enter passwords and numbers.

s "Setting Password Protection" p.115

Corrects distortion in the projected image. s "Correcting Distortion in the Projected Image"

p.64

Performs operations and makes settings for the memory function.

s "Memory Function" p.110

Enlarges or reduces the image without changing the projection size.

s "Enlarging Part of the Image (E-Zoom)" p.104

Part Names and Functions

Name Function

[Default] button

[Esc] button

[Focus] button

[Split] button

[Color Mode] button

Enabled when [Default]: Reset is displayed on the configuration menu guide. The settings being adjusted are returned to their default values.

s "Configuration Menu Operations" p.136

• Stops the current function.

• If pressed when the Configuration menu is displayed, it

moves to the previous level. s "Configuration Menu Operations" p.136

Each time the button is pressed, the adjustment screens for focus and distortion are displayed in that order.

s "Correcting the Focus" p.38

Each time the button is pressed, the image changes between projecting two images simultaneously by splitting the projected screen, or projecting one image as normal.

s "Projecting Two Images Simultaneously (Split Screen)" p.99

Each time the button is pressed, the Color Mode changes.

"Selecting the Projection Quality (Selecting Color

Mode)" p.76

Handy remote control operations

You can perform the following operations by simply pressing one of the buttons on the remote control.

Operation Set

Reverse the projected image vertically. (Switch the Projection between Front and Front/Ceiling) s "Changing the direction of the image (projection mode)" p.31

Selecting the password security settings. s "Managing Users (Password Protection)" p.115

Locking or unlocking some of the operation of the buttons on the remote control.

s "Remote control button lock" p.118

Initializing the settings for the Remote Receiver in the Configuration menu. (Enables all Remote receivers for this projector.)

Hold down the [A/V Mute] button for more than five seconds.

Hold down the [Freeze] button for more than five seconds. The Password Protection screen is displayed, and you can select various settings.

Hold down the [ five seconds.

Hold down the [Menu] button for more than 15 seconds.

] button for more than

[Search] button

[ ] button

Indicator

Remote control light-

emitting area

Changes to the next input source that is sending an image. s "Automatically Detecting Input Signals and Changing

the Projected Image (Source Search)" p.61

Illuminates the buttons on the remote control for approximately 15 seconds. This is useful when using the remote control in the dark.

A light is emitted when outputting remote control signals.

Outputs remote control signals.

Part Names and Functions

Operation Set

Displaying frequently used Configuration menu items.

Press the [User1], [User2], or [User3] button. You can set the menu item you want to assign to each button in User Button.

s Settings - User Button p.143 The following items can be assigned.

Light Source Mode, Multi-Projection, Resolution, On-Screen Display, Display the QR Code, Image Enhancement, Frame Interpolation, Link Menu, Content Playback, USB

When you press the button for which OnScreen Display is assigned, menus or

messages are not displayed on the screen. When the same button is pressed, they are displayed again. If On-Screen Display is enabled, you cannot operate the Configuration menu (except to switch the color mode and input source).

Replacing the remote control batteries

Remove the battery cover.

While pushing the battery compartment cover catch, lift the cover up.

Replace the old batteries with new batteries.

If delays in the responsiveness of the remote control occur or if it does not operate after it has been used for some time, it probably means that the batteries are becoming flat. When this happens, replace them with new batteries. Have two AA size alkaline or manganese batteries ready. You cannot use other batteries except for the AA size alkaline or manganese.

Attention

Make sure you read the following manual before handling the batteries. s Safety Instructions

Caution

Check the positions of the (+) and (-) marks inside the battery holder to ensure the batteries are inserted the correct way.

If the batteries are not used correctly, they could explode or leak causing a fire, injury, or damage to the product.

Part Names and Functions

Replace the battery cover.

Press the battery compartment cover until it clicks into place.

Remote control operating range

To restrict reception of the operation signals from the remote control,

Connecting a cable to the remote control

You can make operations securely with the optional remote control cable set when you use multiple units of this projector in the same place or when there are obstacles around the remote receiver.

set Remote Receiver. s Settings - Remote Receiver p.143

Part Names and Functions

"Optional Accessories" p.233

• When the remote control cable is plugged into the Remote port, the

remote receiver on the projector is disabled.

• You can also connect the optional HDBaseT transmitter and remote control with the cable to control the projector. s "Connecting an HDBaseT Transmitter" p.53

Preparing the Projector

This chapter explains how to install the projector and connect projection sources.

Installing the Projector

Removing and Attaching the Projector Lens Unit

Warning

Make sure you disconnect the power cord from the projector before removing or attaching the lens unit to the projector. Otherwise, it could cause an electric shock.

Attaching

Attention

• Do not attach the lens unit when the projector's lens insertion section is facing up. Dust or dirt could enter the projector.

• Try not to touch the lens section with your hand or fingers. If fingerprints or oils are left on the surface of the lens, projection quality deteriorates.

• The projector supports lens with the following model numbers. ELPLX01, ELPLX01W, ELPLU03, ELPLU04, ELPLW05, ELPLW06,

ELPLW08, ELPLM08, ELPLM09, ELPLM10, ELPLM11, ELPLM15, ELPLL08, ELPLS04, ELPLU02, ELPLR04, ELPLW04, ELPLM06, ELPLM07, ELPLL07

When using the following lens, set the Lens Type in the Configuration menu according to the lens you are using so that distortion correction is performed correctly.

ELPLS04, ELPLU02, ELPLR04, ELPLW04, ELPLM06, ELPLM07, ELPLL07

s Extended - Operation - Advanced - Lens Type p.146

• In a normal installation, the image may be tilted depending on your lens. Adjust the tilt of the image using the front and rear feet.

s "Adjusting the Horizontal Tilt (for Normal Installment)"

p.42

• For information on installing ELPLX01/ELPLX01W, see the User's Guide supplied with ELPLX01/ELPLX01W.

Pull the lens replacement cover straight out.

Release the lock lever if it is locked.

Installing the Projector

When using the following lens, attach the supplied lens connector cap to protect the port.

ELPLS04, ELPLU02, ELPLR04, ELPLW04, ELPLM06, ELPLM07, ELPLL07

Pinch the lever, and then move it counter-clockwise.

Insert the lens unit straight into the lens insertion section with the white circle on the lens on top.

While holding the lens unit firmly, pinch the lever and turn it clockwise to lock the lens unit.

Check that the lens cannot be detached.

Installing the Projector

When projecting down, we recommend securing the front cover with commercially available screws (M3 x 8 mm).

Secure the lever with the lever lock to make sure it does not come loose.

The lever is secured even without using the lever lock, but this

Attach the lens replacement cover.

adds an additional measure of safety.

Lens Calibration

After replacing the lens unit, calibrate the lens so that the projector can correctly acquire the lens position and adjustment range.

After attaching a different lens unit from the previous one, a message is displayed when the projector is turned on.

Select Yes to calibrate the lens.

Lens calibration takes up to about 100 seconds until it is complete. When it is complete, the lens position returns to the position before calibration (ELPLX01/ELPLX01W returns to the standard position).

Installing the Projector

Attention

If the message "Lens Calibration failed." is displayed, remove the lens unit and then reinstall it. If the message continues to be displayed, stop using the projector, remove the power plug from the electrical outlet, and contact your local dealer or the nearest address provided in the Epson Projector Contact List.

s Epson Projector Contact List

• You can perform lens calibration using one of the following

methods.

- Press the [Default] button on the remote control for three seconds or more.

- Configuration Menu s Extended - Operation - Lens Calibration p.146

• If no message is displayed after attaching the lens unit, perform lens calibration from the Configuration menu.

• If you do not calibrate the lens, the following functions may not operate correctly.

Focus, Distortion, Zoom, Lens Shift, Memory (Lens Position)

Attention

If the lens shift has been done, move the lens position to the home position before replacing the lens unit.

s "Adjusting the Position of the Projected Image (Lens Shift Adjustment)"

p.34

The projector uses a laser as the light source. As a safety measure, the

light source turns off when the lens is removed. Attach the lens, and then press the [

Pull the lens replacement cover straight out.

] button to turn it back on.

Removing

Caution

Wait for a while after turning off the projector before removing the lens unit (Approx. 30 mins.). Touching the lens unit immediately after projecting or turning off may cause burns.

If the lock lever has been secured with a stopper, remove the stopper.

+ 261 hidden pages