Epson DM-D501 Installation Manual

Stand Unit for DM Customer Display

Installation Manual

Safety Precautions

This documents uses the two headings shown below to call attention to potential hazards. Failure to observe the information provided alongside these headings may lead to injury or damage to your system. Be sure that you understand the meaning of each heading before you proceed.

WARNING		Indicates a potentially lethal hazard. Failure to observe a WARNING may result in
WARNING		severe injury or death.

CAUTION		Failure to observe a CAUTION may result in personal injury, or in damage to
CAUTION		equipment or other property.


WARNING		Shut down your equipment immediately if it produces smoke, a strange odor,
WARNING		or unusual noise. Continued use may lead to fire.
		Immediately turn the power off and consult your dealer or a SEIKO EPSON
		service center for advice.
		Never attempt to repair this product yourself. Improper repair work can be
		dangerous.
		Tampering with this product may result in injury, fire, or electric shock.
		Never disassemble or modify this product.
		Tampering with this product may result in injury, fire, or electric shock.
		Be sure to use the specified power source.
		Connection to an improper power source may result in fire or electric shock.
		Do not allow foreign matter to fall into the equipment.
		Penetration of foreign objects may result in fire or electric shock.
		If water or other liquid spills into this equipment, immediately turn the power
		off and consult your dealer or a SEIKO EPSON service center for advice.
		Continued usage may result in fire or electric shock.

CAUTION		Be sure to set this product on a firm, stable, horizontal surface.
CAUTION		The product may break or cause injury if it falls.
		Do not use in locations subject to high humidity or dust levels.
		Excessive humidity and dust may cause equipment damage, fire, or electric
		shock.
		Do not place heavy objects on top of this product. Never stand or lean on this
		product.
		Equipment may fall or collapse, causing breakage and possible injury.

Unpacking

Please confirm that this package contains these items:

DM-D stand

Base plate

Extension cable for	RS-232 connector
power supply	installation screw (mm type)

Connecting to the DM Customer Display

Please refer to the DM-D500 User’s Manual for the procedure to connect this unit to the DM-D500.

EMC and Safety Standards Applied

Product Name:	DM Stand
Type Name:	M153A

The following standards are applied only to the DM stand that is so labeled. (EMC is tested using the EPSON

PS-180 power supply.)
Europe:	CE Marking
North America:	Safety:	EN60950-1
North America:	EMI:	FCC/ICES-003 Class A
Japan:	Safety:	UL 1950/CSA C22.2 No.950
Japan:	EMC:	VCCI Class A
Oceania:	EMC:	AS/NZS CISPR22 Class A

WARNING

This is a Class A product. In a domestic environment this product may cause radio interference in which case the user may be required to take adequate measures.

The connection of non-shielded interface cable to this DM stand will invalidate the EMC standards of this device.

You are cautioned that changes or modifications not expressly approved by SEIKO EPSON Corporation could void your authority to operate the equipment.

CE Marking

The display conforms to the following Directives and Norms:
Directive 2004/108/EC EN 55022 Class A
EN 55024	IEC 61000-4-3	IEC 61000-4-4
IEC 61000-4-2	IEC 61000-4-3	IEC 61000-4-4
IEC 61000-4-5	IEC 61000-4-6	IEC 61000-4-11

FCC Compliance Statement for American Users

This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment.

This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense.

For Canadian Users

This Class A digital apparatus complies with canadian ICES-003.

Cet appareil numérique de la classe A est comforme à la norme NMB-003 du Canada.

No part of this publication may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, without the prior written permission of Seiko Epson Corporation. No patent liability is assumed with respect to the use of the information contained herein. While every precaution has been taken in the preparation of this guide, Seiko Epson Corporation assumes no responsibility for errors or omissions. Neither is any liability assumed for damages resulting from the use of the information contained herein. Neither Seiko Epson Corporation nor its affiliates shall be liable to the purchaser of this product or third parties for damages, losses, costs, or expenses incurred by purchaser or third parties as a result of: accident, misuse, or abuse of this product or unauthorized modifications, repairs, or alterations to this product, or (excluding the U.S.) failure to strictly comply with Seiko Epson Corporation’s operating and maintenance instructions.

Seiko Epson Corporation shall not be liable against any damages or problems arising from the use of any options or any consumable products other than those designated as Original Epson Products or Epson Approved Products by Seiko Epson Corporation.

EPSON is a registered trademark of Seiko Epson Corporation in Japan and other countries/regions. NOTICE: The contents of this manual are subject to change without notice.




		DM-D

	RS-232
	( )

DM-500 DM-D500

(VCCI) A

VCCI-A

1 2 3

4 5

（6）

EPSON