Epson DM-D310F User's Manual

User’s Manual / Manuale dell’utente

Standards and Approvals

The following standards are applied only to the liquid crystal displays that are so
labeled. (EMC is tested using the Epson power supplies.)
Europe: CE marking

CE Marking

☞ http://www.epson.eu/conformity

This is a Class A product. In a domestic environment this product may cause
radio interference in which case the user may be required to take adequate
measures.

Questo è un prodotto di Classe A. In ambiente domestico, questo prodotto può
causare interferenze radio. In tal caso, l’utente deve adottare le misure necessarie
per eliminare l’interferenza.

Indication of the manufacturer and the importer in accordance with
requirements of directive 2011/65/EU (RoHS)

Manufacturer: SEIKO EPSON CORPORATION
Address: 3-5, Owa 3-chome, Suwa-shi, Nagano-ken 392-8502, Japan
Web site: http://www.epson.com/
Importer: EPSON EUROPE B.V.
Address: Atlas Arena, Asia Building, Hoogoorddreef 5,1101 BA

Amsterdam Zuidoost The Netherlands

Web site: http://www.epson.com/europe.html

Türkiye'deki kullanıcılar için

AEEE Yönetmeliğine Uygundur.
Ürünün Sanayi ve Ticaret Bakanlığınca tespit ve ilan edilen kullanma ömrü
5 yıldır.
Tüketicilerin şikayet ve itirazları konusundaki başvuruları tüketici
mahkemelerine ve tüketici hakem heyetlerine yapılabilir.
Üretici: SEIKO EPSON CORPORATION
Adres: 3-5, Owa 3-chome, Suwa-shi, Nagano-ken 392-8502 Japan
Tel: [phone]
Web: http://www.epson.com/

Для українських користувачів

Обладнання відповідає вимогам Технічного регламенту обмеження
використання деяких небезпечних речовин в електричному та
електронному обладнанні.

WARNING

AVVERTENZA

2 Standards and Approvals

English

Introduction

This manual presents important information intended to ensure safe and
effective use of this product. Read this section carefully and store it in an
accessible location.

Key to Symbols

The symbols in this manual are identified by their level of importance, as defined
below. Read the following carefully before handling the product.

WARNING

Warnings must be followed carefully to avoid serious bodily injury.

CAUTION

Cautions must be observed to avoid minor injury to yourself, damage to your equipment, or
loss of data.

Safety Precautions

WARNING:

Never attempt to repair this product yourself. Improper repair work can be dangerous.

Never disassemble or modify this product. Tampering with this product may result in injury,
fire, or shock.

Do not allow foreign matter to fall into the equipment. Penetration by foreign objects may
lead to fire.

Do not use aerosol sprayers containing flammable gas inside or around this product. Doing
so may cause fire.

DM-D310F User’s Manual 3

CAUTION:

Do not place heavy objects on this product. Never stand or lean on this product. It may
cause breakage and possible injury.

Do not inflict a strong impact by dropping the unit or treating it roughly.
A glass panel may break, and it may cause injury.

Do not place this product in high temperature or high humidity, and never allow
condensation on this product.
Problems could occur such as malfunction or poor display quality.

The rotating angle of the display is limited by a stopper. Do not apply excess force to rotate it
past the limit set by the stopper. Doing so may cause damage.

Take care when handling the display not to knock it because it has a built-in liquid crystal
display.

Unpacking

The following items are included with the standard specification display.
If any item is damaged, contact your dealer.

❏ DM-D310F ❑ DM-D stand
❏ Ferrite core (large) ❑ Ferrite core (small)
❏ Base plate

4 DM-D310F User’s Manual

Assembling the DM-D310F

DM-D310F

DM-D stand

Projection

Groove

Ferrite core (large)

1. Pass the cable of the DM-D310F through the DM-D stand, as shown in the
illustration below.

2. Insert the pole of the DM-D310F into the hole in the DM-D stand, aligning
the projection on the pole with the wider side of the groove in the inside of
the pole of the DM-D stand (indicated in the semicircular arrow in the
illustration below), and push it until it clicks into place.

Note:

After installing the DM-D310F, check whether the display turns 180 degrees. If
not, make sure the projection on the DM-D310 is set in the wider side of the
groove in the DM-D stand.

3. Pass the cable through the hole in the ferrite core, and wrap the cable once
around the ferrite core.

DM-D310F User’s Manual 5