❏This document shall apply only to the product(s) identified herein.
❏No part of this document may be reproduced, stored in a retrieval system, or
transmitted in any form or by any means, electronic, mechanical, photocopying,
recording, or otherwise, without the prior written permission of Seiko Epson
Corporation.
❏The contents of this document are subject to change without notice. Please
contact us for the latest information.
❏While every precaution has been taken in the preparation of this document,
Seiko Epson Corporation assumes no responsibility for errors or omissions.
❏Neither is any liability assumed for damages resulting from the use of the
information contained herein.
❏Neither Seiko Epson Corporation nor its affiliates shall be liable to the purchaser
of this product or third parties for damages, losses, costs, or expenses incurred
by the purchaser or third parties as a result of: accident, misuse, or abuse of this
product or unauthorized modifications, repairs, or alterations to this product, or
(excluding the U.S.) failure to strictly comply with Seiko Epson Corporation's
operating and maintenance instructions.
❏Seiko Epson Corporation shall not be liable against any damages or problems
arising from the use of any options or any consumable products other than
those designated as Original EPSON Products or EPSON Approved Products by
Seiko Epson Corporation.
TRADEMARKS
EPSON® is a registered trademark of Seiko Epson Corporation.
Microsoft
trademarks of Microsoft Corporation.
General Notice: Other product and company names used herein are for
identification purposes only and may be trademarks of their respective companies.
, MS®, MS-DOS®, Windows® and Windows NT® are registered
Page 3
Safety Precautions
This document presents important information intended to ensure safe and effective use
of this product. Please read this document carefully, and store it in an accessible location
near your installation.
Precaution Headings
This document uses the two headings shown below to call attention to potential hazards.
Failure to observe the information provided under or alongside these headings may lead
to injury or property damage. Be sure that you understand the meaning of each heading
before you proceed.
WARNING:
Indicates a potentially lethal hazard. Failure to observe a WARNING
may result in severe injury or death.
CAUTION:
Failure to observe a CAUTION may result in personal injury, or in damage
to equipment or other property.
Safety Precautions
WARNING:
❏
Shut down your equipment immediately if it produces smoke, a
strange odor, or unusual noise. Continued use may lead to fire or
electric shock. Immediately turn the power off and contact your
dealer or a SEIKO EPSON service center for advice.
English
❏
Never attempt to repair this product yourself. Improper repair work
can be dangerous. Tampering with this product may result in injury,
fire, or electric shock.
❏
Be sure to use the specified power source. Connection to an
improper power source may cause fire or shock.
❏
Do not allow foreign matter to fall into the equipment. Penetration
of foreign objects may lead to fire or shock.
❏
If water or other liquid spills into this equipment, immediately turn the
power off and contact your dealer or a SEIKO EPSON service center
for advice. Continued usage may lead to fire or shock.
1
Page 4
CAUTION:
❏
Do not plug the cable differently from the instruction in this manual.
Wrong connection may cause equipment damage and fire.
❏
Be sure to set this equipment on a firm, stable, horizontal surface.
Product may be damaged or cause injury if it falls.
❏
Do not use in locations subject to high humidity or dust levels.
Excessive humidity and dust may cause equipment damage, fire, or
shock.
❏
Do not place heavy objects on top of this product. Equipment may
be damaged and cause injury if it falls.
❏
Do not attach more than one extension support. Product may be
damaged or cause injury if it falls.
❏
A stopper limits the horizontal rotation of the display. Do not try to
force it to turn beyond the limits of the stopper. Doing so may
damage the equipment.
❏
If the DM-D110 is used with the TM-H5200, be sure to attach a ferrite
core to meet the EMC standards. It is prohibited legally to import
and sell products that do not meet the EMC standards in countries
where the standards are applied. Using the products that do not
meet the EMC standards may cause radio interference to other
electronic equipments.
EMC and Safety Standards Applied
Product Name: DM-D110
Type Name: M58DB
The following standards are applied only to the display that is so labeled. (EMC is tested
using the EPSON PS-170 power supply.)
❏Europe:CE Marking
Safety: EN60950
❏North America: EMI: FCC/ICES-003 Class A
Safety: UL 1950/CSA C22.2 No.950
❏Japan: EMC: VCCI Class A JEIDA-52
❏Oceania: EMC: AS/NZS 3548 (CISPR22) Class B
CE Marking
The display conforms to the following Directies and Norms
You are cautioned that changes or modifications not expressly approved by SEIKO
EPSON Corporation could void your authority to operate the equipment.
FCC COMPLIANCE STATEMENT FOR AMERICAN USERS
This equipment has been tested and found to comply with the limits for a Class A digital
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference when the equipment is operated in a
commercial environment.
This equipment generates, uses, and can radiate radio frequency energy and, if not
installed and used in accordance with the instruction manual, may cause harmful
interference to radio communications. Operation of this equipment in a residential area is
likely to cause harmful interference in which case the user will be required to correct the
interference at his own expense.
FOR CANADIAN USERS
This Class A digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la classe A est conforme à la norme NMB-003 du Canada.
English
About This Manual
Cautions and Notes
CAUTION:
Cautions must be observed to avoid minor injury to yourself or damage
to your equipment.
Note:
Notes have important information and useful tips on the operation of your display.
Make sure that you have all the items shown above, and that none has
been damaged. If you find anything missing or damaged items, please
contact your DM-D110 dealer.
Cautions on Handling
When you use the DM-D110, be sure to note the following points:
❏
Avoid locations that are subject to high temperature and humidity.
❏
Avoid dirty and dusty locations.
❏
Avoid locations that are unstable or are subject to high levels of
vibration.
❏
When connecting or disconnecting cables, make sure that the
power switch of the DM-D110 and printers connected to the
DM-D110 are turned off.
❏
Do not drop the DM-D110 because you may damage the built-in
vacuum fluorescent display.
❏
Attach the ferrite core before connecting to a printer.
5
Page 8
Usage
The DM-D110 can be used with the following equipment.
❏
IM series
“DM-D pole unit for IR” (DP-504). (See page 7.)
❏
TM-H5000II/TM-J8000 printers
TM-H5000II/TM-J8000 printers using the “DM-D pole unit for TM
printers (Type B)” (DP-503). (See page 9.)
❏
TM-U375/TM-U950
TM-U950 printers using the “DM-D pole unit for TM printers
(Type A)” (DP-502). (See page 13.)
❏
TM-H6000/TM-U675
TM-U675 printers using the “DM-D pole unit for TM printers
(Type A)” (DP-502). (See page 16.)
❏
Other TM printers
pole unit for TM printers (Type A)” (DP-502) and Velcro tapes or
screws. (See page 21.)
❏
DM-D stand
directly using the “DM-D stand unit for DM Customer Display”
(DP-110). When using the DM-D stand, an optional power supply
unit (PS-170) is required. Also, if you want to extend the height of
the DM-D110, an optional extension support unit (DP-105) is
required. (See page 24.)
. You can attach the DM-D110 to the IM series using the
. You can attach the DM-D110 to
. You can attach the DM-D110 to the TM-U375/
. You can attach the DM-D110 to TM-H6000/
. You can attach the DM-D110 using the “DM-D
. You can attach the DM-D110 to the DM-D stand
6
Page 9
Assembling
fixing screws
support B
(for extension)
When using support B for
extension
Attaching to the IM series
The DM-D110 can be attached directly to the IM series using the
“DM-D pole unit for IR” (DP-504).
Required items
The following items are used to attach the DM-D110 to the IM series.
These items are packed with the “DM-D pole unit for IR” (DP-504).
base
support A
Assembling steps
1.Pass the cable for the DM-D110 through support A, and attach
support A to the DM-D110.
When using support B for extension, insert the tab on support B
into the hole on support A until you feel it click.
English
7
Page 10
2.Attach the base to the setting position on the IM series and secure it
with the screws.
Note:
When attaching the base, note that the corners of the base are set as shown
below.
3.Pass the cable for the DM-D110 through the base.
4.Insert the tab on the base into the hole on the support until you feel
it click.
.
8
Page 11
5.Connect the cable for the DM-D110 to the DM connector on the IM
support B
(for extension)
series.
CAUTION:
Arange the cable so that it does not touch the FAN below . When the
cable touches the FAN, it may cause abnormal sounds or break the
cable.
The place of the DM connector depends on the model of IM
series.
Attaching to the TM-H5000II/TM-J8000
The DM-D110 can be attached directly to the TM-H5000II/TM-J8000
printers using the “DM-D pole unit for TM printers (Type B)” (DP-503).
English
Required items
The following items are used to attach the DM-D110 to the TM-H5000II
/TM-J8000 printers. These items are packed with the “DM-D pole unit
for TM printers (Type B)” (DP-503).
fixing screws
base
support C
9
Page 12
Assembling steps
When using support B for
extension
1.Pass the cable for the DM-D110 through support C and attach
support C to the DM-D110.
When using support B for extension, insert the tab on support B
into the hole on support C until you feel it click.
2.Attach the base to the setting position on the TM printer and secure
it with the screws.
10
Page 13
3.Pass the cable for the DM-D110 through the base.
4.Insert the tab on the base into the hole on the support until you feel
it click.
5.When connecting to the TM-H5200, attach the ferrite core, which is
packed with the DM-D110, to the part near the connector of the
DM-D110 connecting cable. When connecting to other products,
you do not need to attach the ferrite core.
English
11
Page 14
6.Connect the cable for the DM-D110 to the DM connector on the TM
printer.
12
Page 15
Attaching to the TM-U375/TM-U950
rubber feet
(square)
t
f
fixi
The DM-D110 can be attached directly to the TM-U375/TM-U950
printers using the “DM-D pole unit for TM printers (Type A)”
(DP-502).
Required items
The following items are used to attach the DM-D110 to the TM-U375/
TM-U950 printers. These items are packed with the “DM-D pole unit
for TM printers (Type A)” (DP-502).
English
<For TM-U375>
fixing screws
for rubber feet
(large)
support C
<For TM-U950>
rubber fee
(large)
ixing screws
for metallic
portion
<For TM-U375 and TM-U950>
support B
for extension
rubber feet
(square)
ng screws
for plastic position
fixing plate A
13
Page 16
Assembling steps
When using support B
for extension
1.Pass the cable for the DM-D110 through support C and attach
support C to the DM-D110.
When using support B for extension, insert the tab on support B
into the hole on support C until you feel it click.
2.Attach the rubber feet to the printer.
14
[TM-U375]
[TM-U950]
Page 17
3.Pass the cable for the DM-D110 through the hole on fixing plate A
[TM-U950]
and fix the cable at the bottom as shown below.
4.Connect the cable for the DM-D110 to the DM connector on the TM
printer.
English
5.Adjust the length of the cable and secure fixing plate A to the
printer with screws.
[TM-U375]
15
Page 18
6.Store any excess cable in the support, and attach the DM-D110 to
fixing plate B
fixing screws for
fixing plate B
fixing plate A
fixing plate A.
Attaching to the TM-H6000/TM-U675
The DM-D110 can be attached directly to the TM-H6000/TM-U675
printers using the “DM-D pole unit for TM printers (Type A)”
(DP-502). You can attach fixing plate A on either side of the
TM-H6000/TM-U675. After attaching it, you can slide the display
freely.
Required items
The following items are used to attach the DM-D110 to the TM-H6000/
TM-U675 printers. These items are packed with the “DM-D pole unit
for TM printers (Type A)” (DP-502).
16
stopper
fixing screws for
rubber feet (small)
support C
fixing screw
for stopper
rubber feet (small)
support B
for extension
angle fixing
screw
Page 19
Assembling steps
When using support B
for extension
1.Pass the cable for the DM-D110 through support C, and attach
support C to the DM-D110.
When using support B for extension, insert the tab on support B
into the hole on support C until you feel it click.
2.Attach the rubber feet to the printer.
English
3.Attach fixing plate B to the printer.
17
Page 20
4.Pass the cable for the DM-D110 through the hole on fixing plate A,
and fix the cable at the bottom as shown below.
5.Connect the cable for the DM-D110 to the DM connector on the TM
printer.
6.Attach fixing plate A to the TM printer using the stopper. When
you attach the stopper, insert the projections on the stopper into the
holes of fixing plate B. Fixing plate A can be attached on either side
of the printer. (The illustration below shows fixing plate A attached
to the right side of the printer.)
18
Page 21
7.The horizontal rotation mechanism of fixing plate A can be
adjusted. To secure the location of the display, set fixing plate A to
either one of the following four positions and secure it with the
angle fixing screw.
English
19
Page 22
Note:
The paper roll cover may not open if the position of the display is
inappropriate. Before securing the position of the display, make sure that
you can open the paper roll cover.
paper roll cover
8.Store any excess cable in the support and attach the DM-D110 to
fixing plate A.
9.Connect the power cable of the printer. To avoid disconnection,
hook the cable to the tabs on fixing plate B, as shown below.
20
Page 23
Attaching to Other TM Printers
Velcro tapes
support B (for extension)
When using with other TM printers, the DM-D110 can be attached to a
desk or other surface, using the “DM-D pole unit for TM printers
(Type A)” (DP-502), and Velcro tapes or screws.
Required items
The following items are used when the DM-D110 is used with other
TM printers. These items are packed with the “DM-D pole unit for TM
printers (Type A)” (DP-502).
Velcro tapes
fixing plate A
English
Assembling steps using Velcro tapes
1.Attach Velcro tapes to the bottom of fixing plate A.
fixing screws for
wood position
support C
21
Page 24
2.Pass the cable for the DM-D110 through support C and attach
When using support B
for extension
support C to the DM-D110.
When using support B for extension, insert the tab on support B
into the hole on support C until you feel it click.
3.Pass the cable for the DM-D110 through the hole on fixing
plate A, and fix the cable at the bottom as shown below.
4.Connect the cable for the DM-D110 to the DC connector on the
22
TM printer.
Page 25
5.Store any excess cable in the support, and attach the DM-D110
to fixing plate A.
6.Peel off the Velcro tapes and attach the display to the setting
position.
Assembling steps using screws
1.Follow steps 2 and 3 in “Assembling steps using Velcro tapes.”
2.Secure fixing plate A to the setting position with fixing screws.
English
3.Attach the DM-D110 to fixing plate A.
23
Page 26
Attaching to the DM-D stand
<power supply unit (PS-170)>
>
>
power
supply unit
The DM-D110 can be attached directly to the DM-D stand using the
“DM-D stand unit for DM Customer Display” (DP-110). The DM-D110
with the DM-D stand can be connected to a TM printer, or be used as a
standalone product.
Required items
The following items are used to attach the DM-D110 to the DM-D
stand. Note that an optional power unit (PS-170) is required when
using the DM-D stand. If you want to extend the length of the
DM-D110. You must get the items separately from the DM-D stand unit
(DP-501).
<DM-D stand unit for DM Customer Display (DP-110)
<extension support (DP-105)
Velcro tapes
24
DM-D stand
extension cable for
power supply
extension support
interface connector
base plate
RS-232C connector installation screw
(mm type)
AC cable
Page 27
Connectors for the DM-D stand
printer connector
extension cable connector
RS-232C connector
installation screw
The connectors for the DM-D stand are as follows:
computer connector
power supply unit connector
display connector
Note:
The DM-D stand comes with inch-type hexagonal lock screws installed to
secure the interface cable to the interface connector for RS-232. If you plan to
use an interface cable which requires millimeter-type lock screws, replace the
inch-type screws with the included millimeter-type screws using a hex
screwdriver (5mm). To distinguish the two types of screws, see the illustration
below.
notch (one or more lines)
inch-type
millimeter-type
English
25
Page 28
Jumper setting
Set the jumpers on the DM-D stand as follows:
JP1JP2Perpose
1-21-2For connecting both the TM printer and the DM-D stand.
(Default setting)
2-32-3For using the DM-D stand a standalone.
(TM printer is not connected.)
The jumpers are located as follows:
JP1
JP2
Precautions on using the power supply unit
To avoid damage to the DM-D110 and the power supply unit, make
sure to note the following points.
❏
Use the optional Seiko Epson products, PS-170,PS-180, or PA-6508,
PA-6511, PA-6513, PB-6509 or PB-6510 as the power supply.
❏
Never connect the DC cable to the power supply unit when the
power supply unit is connected.
26
❏
Unplug the DC cable by holding the connector part. If you pull the
cable to unplug it, it may be damaged.
Page 29
Assembling steps
When using the
extension support
(DP-105)
1.Pass the cable for the DM-D110 through the DM-D stand.
When extending the length of the DM-D stand, attach the extension
support (DP-105) to the DM-D stand.
2. Insert the tab on the DM-D110 (or the extension support) into the
hole on the DM-D stand until you feel it click.
English
27
Page 30
3.Connect the cable for the DM-D110 to the display connector on the
DM-D stand until you feel it click.
4.Connect one end of the computer interface cable to the computer
connector on the DM-D stand; then connect the other end to the
RS-232 connector on the computer. Tighten the screws on both ends
of the cables to fasten them.
computer
28
Page 31
5.When using as a standalone, go to step 6.
e
extension cable for
power supply
When using with a printer, connect one end of the printer interface
cable for the printer to the printer connector on the DM-D stand;
then connect the other end to the connector on the printer. Tighten
the screws on both ends of the cable to fasten them.
printer
6.When not using the extension cable for power supply packed with
the DM-D stand, go to step 7.
When using the extension cable, connect it (with the arrow mark
up) to the extension cable connector indicated with “POWER OUT”
on the DM-D stand; then connect the other end to the power
connector on the printer.
English
extension cabl
connector
29
Page 32
7.Connect the DC cable of the power supply unit (with the arrow
DC cable of power
supply unit
mark up) to the power supply unit connector indicated with
“POWER IN” on the DM-D stand.
power supply unit
connector
8.When using as a stand alone product, set the jumpers. (See “Jumper
setting” on page 26.)
9.Arrange the cables as shown below. Put the cables for the DM-D110
inside the DM-D stand.
30
Page 33
10. Attach the base plate to the DM-D stand following the number of
the arrow shown below. At this time, push the base plate until it is
locked by the hook on the DM-D stand.
11. When the extension support (DP-105) is used, attach Velcro tapes to
the four corners of the plate to keep the unit from falling down.
12. Connect the cord of the power unit to the socket.
English
31
Page 34
Part Names and Functions
DIP switch
(rear side of the display)
Exterior
display
power switch
(bottom of the display)
❏
Display: Characters are displayed.
❏
Power switch: The power is turned on/off.
❏
DIP switch: The functions of the DM-D110 are changed.
(See “DIP switch” for details.)
Note:
When turning on the DM-D110 again after turning it off, wait for at least
3 seconds.
32
Page 35
DIP Switch
DIP Switch Functions
The DM-D110 has one DIP switch. The functions of the DIP switch are
as follows:
DIP switch 1
DSW1 No.FunctionONOFFDefault setting
1-1Data receive errorIgnoredDisplays “?”OFF
1-2Data length7 bits8 bitsOFF
1-3Parity on or offParityNo parityOFF
1-4Parity typeEvenOddOFF
1-5
1-6OFF
1-7ON
1-8Self test selection (*)Perform self
(*)This function can select whether or not the self test is performed when you turn on
Change transmis-
sion speed
the power. See “Self Test” for details.
See “Transmission speed.”
test
Do not per-
for m
ON
OFF
Transmission speed
SW1-5SW1-6SW1-7Transmission speed (bps)
English
ONONON2400
OFFONON4800
ONOFFON9600
OFFOFFON19200
ONON OFF38400
OFFONOFF57600
ONOFFOFF115200
OFFOFFOFFreserved
33
Page 36
Setting the DIP switches
CAUTION:
Turn off the DM-D110 while removing the DIP switch cover to
prevent electrical damage to the DM-D110.
1.Turn off the power for the DM-D110.
2.Remove the DIP switch cover.
DIP switch cover
3.Change each setting of the switches with a pointed object, such as a
pen tip or small screwdriver.
4.Close the cover and turn the power on.
34
Page 37
Turning and Tilting the DM-D110
You can turn or tilt the display while holding the support. The display
can be moved easily, so do not move any further if it stops. If you move
it by force, you may damage it.
With the “DM-D pole unit for IR” (DP-504) and the “DM-D pole unit
for TM printers (Type B)” (DP-503), the display area may not face the
direction you desire. In this case, remove the base, change the position
of the tab of the base so that the display faces to the direction you
desire, and reattach it to the base.
English
48
°
45
45° for left
(you can turn the same angle to the right.)
°
The display area has the following range of movement:
❏
Tilt: 48° max. (4 steps, 5 positions)
❏
Horizontal rotation: 90° max. (45° each, left and right)
35
Page 38
Self Test
The DM-D110 has a self test function. If you want to perform a self test,
you must change the setting of the DIP switch.
Check Items of Self test
The following items are checked during the self test:
❏
Control ROM version
❏
DIP switch settings
❏
Memory switch settings
❏
Example of display characters
❏
Example of each function, such as brightness, flashing, and scroll
Performing Self test
To perform the self test, follow the steps below.
1.Turn off the power for the DM-D110.
2.Set SW 1-8 of the DIP switch to ON, and turn on the power.
Note:
If the contents of the self test are not displayed, the DM-D110 may be
malfunctioning. Please contact your DM-D110 dealer for assistance.
When the self test is finished and no error occurs, the DM-D110 is ready
to receive data.
Diagnostics
The DM-D110 has a diagnostics function. When the DM-D110 is turned
on, diagnostics, such as internal memory test, are carried out regardless
of the DIP switch settings. When an error is detected, the error message
is displayed and no operation is carried out until power is turned off.
36
Page 39
Specification
General Specifications
❏
Height, Width, Depth and Weight
<DM-D110 and DM-D stand>
50.5
DM-D110
63
110
DM-D stand (DP-110)
English
165
69
165
•DM-D110:
Height:69 mm
Width:165 mm
Depth:50.5 mm
Weight:285 g
•DM-D stand (DP-501):
Height:63 mm
Width:165 mm
Depth:110 mm
Weight:385 g
37
Page 40
DM-D pole unit for
TM printers (Type A)
(DP-502)
78 mm
DM-D pole unit for IR
(DP-504)
<DM-D pole units>
DM-D pole unit for
TM printer (Type B)
(DP-503)
50 mm
129 mm
248 mm
base
53 mm
260 mm
164 mm
•Base and support A of the “DM-D pole unit for IR” (DP-504):
Height:129 mm
Width:50 mm
Depth:53 mm
Weight:60 g
•Base and support C of the “DM-D pole unit for TM printers
(Type B)” (DP-503):
Height:248 mm
Width:50 mm
Depth:53 mm
Weight:116 g
38
•Fixing plate A and support C of the “DM-D pole unit for TM
printers (Type A)” (DP-502):
Height:260 mm
Width:78 mm
Depth:164 mm
Weight:264 g
Page 41
❏
Tilt angleMax 48° (4 steps, 5 positions)
❏
Horizontal rotation
Max 90° (for each left and right at 45°)
❏
Vacuum fluorescent display
•Number of characters:20 column × 2 lines max.
English
•Display color:
•Brightness:690 (cd/m
Electrical Specifications
❏
TypePS-170, PS-180, PA-6508, PB-6509, PB-6510,
PA-6511, PA-6513 (when using the DM-D stand)
❏
Rated voltage DC 11.4 to 48 V
❏
Rated current 0.2 A (max.)
Environmental Specifications
❏
Operation environment
Temperature: 5°C to 40°C
Humidity: 30% to 85% (No condensation)
❏
Storage environment
Temperature:−10°C to 50°C
Humidity:30% to 90% (No condensation)
Green (505 nm)
2
)
39
Page 42
Character Specifications
❏
Type of character
•Alphanumeric characters: 95
•International characters: 37
•Extended graphics: 128 characters × 12 pages
❏
Character grid
•Font : 5
•Character size 3.5 mm x 5.0 mm
•Character pitch5.2 mm
Reliability Specification
❏
MTBF (vacuum fluorescent display only)
×
7 dot, cursor
20,000 hours
(When the brightness is reduced to half)
40
Loading...
+ hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.