Epson 31000, 61000 User Manual

PowerLite® Pro Cinema 31000/61000

Home Theater Projector

User’s Guide

Copyright Notice

All rights reserved. No part of this publication may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, without the prior written permission of Seiko Epson Corporation. The information contained herein is designed only for use with this Epson product. Epson is not responsible for any use of this information as applied to other products.

Neither Seiko Epson Corporation nor its affiliates shall be liable to the purchaser of this product or third parties for damages, losses, costs, or expenses incurred by purchaser or third parties as a result of: accident, misuse, or abuse of this product or unauthorized modifications, repairs, or alterations to this product, or (excluding the U.S.) failure to strictly comply with Seiko Epson Corporation’s operating and maintenance instructions.

Seiko Epson Corporation shall not be liable for any damages or problems arising from the use of any options or any consumable products other than those designated as Original Epson Products or Epson Approved Products by Seiko Epson Corporation.

Trademarks

Epson is a registered trademark, 1080Perfect and C2Fine are trademarks, and Epson Exceed Your Vision is a registered logomark of Seiko Epson Corporation.

PowerLite and PrivateLine are registered trademarks, DigiScan and AccuCinema are trademarks, and Extra Care and Epson Connection are service marks of Epson America, Inc.

AMX, the AMX logo, and Device Discovery are registered trademarks of AMX.

Crestron and the Crestron logo are registered trademarks of Crestron Electronics, Inc.

HDMI, the HDMI logo, and High-Definition Multimedia Interface are registered trademarks of HDMI Licensing, LLC.

Pixelworks, DNX, and the DNX logo are trademarks of Pixelworks, Inc.

x.v.Color is a trademark of Sony Corporation.

General Notice: Other product names used herein are for identification purposes only and may be trademarks of their respective owners. Epson disclaims any and all rights in those marks.

This information is subject to change without notice.

CPD-28058

Introduction

Projector Parts

Remote Control

Optional Accessories

Registration and Warranty

Using This Manual

Setting Up the Projector

Choosing a Location

Installing the Projector

Connecting the Cables

Connecting Video and Computer Equipment

Making Other Connections

Installing Batteries in the Remote Control

Turning the Projector On and Off

Turning On the Projector

Turning Off the Projector

Selecting the Image Source

Positioning the Image

6 7

9 10 10 11

12 12 16 18 18 19 20 21 21 22 22 23

Making Basic Adjustments

Focusing and Zooming

Choosing the Aspect Ratio

Choosing the Color Mode

Advanced Color Adjustments

Adjusting the Gamma Setting

Adjusting RGBCMY

Locking the Projector

25 25 26 27 27 28 29 29

Contents

Making Detailed Adjustments

Using the Menu System

Changing How the Menus Display

Adjusting the Picture Quality

Input Brightness Settings

Sharpness and Picture Quality Settings

Color Settings

Adjustments for Computer Images

Selecting Memory Settings and Resetting the Projector

Selecting Memory Settings

Creating Memory Settings

Renaming Memory Settings

Deleting Saved Memory Settings

Resetting the Projector

Customizing Projector Features

Image Sizing

Screen Options

Other Setup Options

Making Network Settings

31 31 32 32 33 34 36 39 39 40 40 40 41 41 42 42 43 44 46

Using HDMI Link

Setting Up HDMI Link

Using HDMI Link

Using the Projector on a Network

Connecting the Projector to Your Network

Monitoring the Projector with a Web Browser

Setting Up E-mail Alerts

Receiving E-mail Alerts

Maintenance

Cleaning the Lens

Cleaning the Projector Case

Contents

48 48 49

50 50 51 51 52

53 53 54

Cleaning and Replacing the Air Filter

Replacing the Lamp

Resetting the Lamp Usage Timer

Checking the Projector Status

Storing the Projector

Transporting the Projector

54 56 59 59 60 60

Problem Solving

What To Do When the Lights Come On or Flash

Solving Picture Problems

Solving Remote Control Problems

Solving Other Problems

Where to Get Help

Specifications

General

Lamp

Remote Control

Dimensions

Electrical

Environmental

Safety

Compatible Video Formats

ESC/VP21 Command Codes

61 61 63 66 67 67

69 69 69 69 70 70 70 71 71 74

Notices

Important Safety Information

FCC Compliance Statement

Declaration of Conformity

Epson America, Inc. Limited Warranty

Index

75 75 77 78 79

Contents

Introduction

The PowerLite® Pro Cinema 31000/61000 projector lets you enjoy theater-quality images in the relaxing environment of your own home. Designed especially for home cinema use, it offers these outstanding features:

■

Native 1080p (1920 × 1080) resolution, dynamic contrast ratio up to 1000000:1 (500000:1 for the Pro Cinema 31000), and up to 1200 lumens of brightness (white light output and color light output) for incredibly rich, sharp images in any room lighting

■

Auto Iris system that constantly controls the light output based on the gamma and black/white levels of your projected content, for perfectly adjusted images and deepest blacks

■

Epson® C2Fine™ 3LCD technology for reliable picture quality, increased contrast ratio and uniform colors

■

1080Perfect™ video processing using HQV® Reon-VX technology for more film-like images free of noise or artifacts

■

10-bit with partial 12-bit color quality for unmatched color accuracy, with over a billion colors available

Introduction

■

Epson AccuCinema™ color management delivered by the built-in optical Cinema Filter blocks out excess light for an expanded, purer color range and sophisticated grayscale tracking

■

HDMI™ (High Definition Multimedia Interface™) port for superior, uncompressed digital video

■

True 16:9 wide-format projection

■

Flexible setup configurations, including front projection and ceiling mounted, with vertical and horizontal offset lens shift

■

Five color modes, including x.v.Color™, to quickly optimize viewing for different lighting environments, and a vast array of custom color adjustments

Projector Parts

Front

Control panel (side)

Infrared receiver (rear)

Lamp cover

Ventilation slots

Back

AC power inlet

(intake)

Lens cover

Component video port

PC port

Infrared receiver (front)

Cable holders

Video port

Adjustable foot

Kensington lock port

Ventilation slots (exhaust)

Control port (RS-232C)

Main power switch

S-Video port

LAN port (Pro Cinema 61000 only)

HDMI ports

Trigger out ports (second port on Pro Cinema 61000 only)

Introduction

Bottom

Air filter cover release

Mounting bracket attachment points

Optional cable cover attachment points

Projector Control Panel

Status lights (see page 61)

Introduction

Power button

Menu button Displays the menus

Lens button Adjusts focus, zoom, and lens shift

Source button Switches the video input source

Esc button Exits the current menu item

Enter button Selects menu items or opens the line menu

Menu navigation buttons

Remote Control

Power buttons Turn projector on or off

Lens Shift button Moves image up/down/left/right

Zoom button Adjusts the image size

Focus button Sharpens the image

Default button Restores default settings when menu is displayed

Illumination button Lights the remote control buttons for easy viewing

Source buttons Switch between equipment connected to the projector

HDMI Link buttons Let you operate HDMI CEC compatible devices

Menu navigation buttons

Enter button Selects menu items or opens the line menu

Esc (escape) button Exits the current menu item

Menu button Displays the projector’s menus

Memory button Recalls custom picture settings

Lens Iris button Adjusts the amount of light passing through the lens

Aspect button Changes the picture’s aspect ratio

RGBCMY button Adjusts the hue, saturation, and brightness for each color

Super-res button Sharpens blurred edges of upscaled images

Pattern button Displays test patterns to adjust the image

Color Mode button Optimizes viewing for different lighting environments

Frame Int (interpolation) button Smooths motion in rapid pictures

Blank button Temporarily stops projection or hides the menu screen

Introduction

Optional Accessories

Epson provides the following optional accessories for the projector:

Product Part number

Replacement lamp V13H010L66

Air filter replacement V13H134A28

Kensington security lock (anti-theft device) ELPSL01

Cable cover V12H003005

Projector mount ELPHB800

Panamorph™ Fixed Anamorphic Lens Kit ELPFALK

Panamorph Movable Anamorphic Lens Kit ELPALK2

In addition to the accessories listed above, 1-year and 2-year extended service plans are available. You can purchase these plans and other accessories from an authorized Epson reseller. To find the nearest reseller, please call 800-GO-EPSON (800-463-7766). To purchase online, visit www.epsonstore.com (U.S. sales) or www.epson.ca (Canadian sales).

Registration and Warranty

Introduction

Your projector comes with a basic three-year carry-in warranty. For details, see page 79.

In addition, Epson offers free Extra Care

Home Service. In the unlikely event of an equipment failure, you won’t have to wait for your unit to be repaired. Instead, Epson will ship you a replacement unit anywhere in the United States, Canada, or Puerto Rico. See your Extra Care Home Service brochure for details.

To register, simply follow the registration instructions on the CD, or register online at www.epson.com/webreg. Registering also lets you receive special updates on new accessories, products, and service.

Using This Manual

This book contains all the information you need to use the projector, in addition to basic setup and maintenance instructions, troubleshooting tips, important safety instructions, specifications, and warranty information.

Please follow these guidelines as you read through the manual:

Warning: Must be followed carefully to avoid bodily injury.

Caution: Must be observed to avoid damage to your equipment.

Note: Contains important information about your projector.

Tip: Contains helpful projection tips.

Need additional help? Take advantage of Epson’s automated support services 24 hours a day at www.epson.com/support (U.S.) or epson.ca/support (Canada). Use this site to view FAQs (Frequently Asked Questions) or product information and e-mail your questions to Epson support.

If you need more help, you can use the Epson PrivateLine (800) 637-7661 and enter the PIN on the PrivateLine support card that came with your projector.

Support service. Call

Introduction

Setting Up the Projector

Follow the instructions in this section to choose a location for the projector, connect the cables, and display an image.

Choosing a Location

You can install the projector for the viewing setups shown below, as well as rear projection.

Center

Side

Ceiling

Setting Up the Projector

Ideally, keep the projector level and place it at a height so its lens is centered between the top and bottom of the screen, as shown below. If this is not possible, use the lens shift function to reposition the image (see page 23). As a rule of thumb, you can use lens shift to move the image up or down by nearly its full height, and left or right by about one-half its width (for details, see page 24).

Offset A

Offset B

Offset refers to distance from

Projection distance

bottom of image to center of lens using maximum lens shift.

If you place the projector off to the side, aim it straight ahead (rather than at the center of the screen), then use the horizontal lens shift to center the image on the screen.

Caution: Do not try to move the lens by hand, or you may damage the projector. Always use the lens shift function to change the lens position.

Setting Up the Projector

The size of the image is determined by the distance from the projector’s lens to the screen. Depending on your display settings, the actual size may differ. Use these tables as a guide for projector placement:

16:9 aspect ratio

Diagonal image size

Projection distance

2.7 to 5.9 feet

0.83 to 1.79 m

(width × height) Offset A Offset B

30 in. (26 × 15 in.)

76.2 cm (66 × 37 cm)

5.1 in. 13 cm

20.6 in. 52 cm

3.6 to 7.9 feet

1.11 to 2.40 m

5.5 to 11.8 feet

1.69 to 3.61 m

7.4 to 15.8 feet

2.26 to 4.82 m

9.3 to 19.8 feet

2.83 to 6.04 m

11.2 to 23.8 feet

3.41 to 7.25 m

14.0 to 29.8 feet

4.27 to 9.08 m

18.7 to 39.7 feet

5.70 to 12.11 m

4:3 aspect ratio

Projection distance

3.3 to 7.2 feet

1.02 to 2.20 m

4.5 to 9.6 feet

1.37 to 2.94 m

6.8 to 14.5 feet

2.07 to 4.43 m

7.4 to 19.4 feet

2.27 to 5.91 m

40 in. (35 × 20 in.)

101.6 cm (89 × 50 cm)

60 in. (51 × 28 in.)

152.4 cm (130 × 75 cm)

80 in. (71 × 39 in.)

203.2 cm (180 × 100 cm)

100 in. (87 × 47 in.) 254 cm (220 × 120 cm)

120 in. (106 × 59 in.) 305 cm (270 × 150 cm)

150 in. (130 × 75 in.) 381 cm (330 × 190 cm)

200 in. (173 × 98 in.) 508 cm (440 × 249 cm)

Diagonal image size (width × height) Offset A Offset B

30 in. (24 × 18 in.)

76.2 cm (61 × 46 cm)

40 in. (32 × 24 in.)

101.6 cm (81 × 61 cm)

60 in. (47 × 35 in.)

152.4 cm (120 × 90 cm)

80 in. (63 × 47 in.)

203.2 cm (160 × 120 cm)

7.8 in. 20 cm

11.8 in. 30 cm

15.7 in. 40 cm

19.6 in. 50 cm

24 in. 60 cm

29 in. 75 cm

39 in. 87 cm

7.2 in. 18 cm

9.6 in. 24 cm

14.4 in. 37 cm

19.2 in. 49 cm

27.5 in. 70 cm

41.2 in. 105 cm

54.9 in. 139 cm

68.6 in. 174 cm

82 in. 209 cm

103 in. 262 cm

137 in. 336 cm

25.2 in. 64 cm

33.6 in. 85 cm

50.4 in. 128 cm

67.2 in. 171 cm

11.4 to 24.3 feet

3.48 to 7.40 m

Setting Up the Projector

100 in. (79 × 59 in.) 254 cm (200 × 150 cm)

24 in. 61 cm

84 in. 213 cm

4:3 aspect ratio

Projection distance

13.7 to 29.2 feet

4.18 to 8.89 m

17.2 to 36.5 feet

5.23 to 11.12 m

Diagonal image size (width × height) Offset A Offset B

120 in. (94 × 71 in.) 305 cm (240 × 180 cm)

150 in. (118 × 91 in.) 381 cm (300 × 230 cm)

29 in. 73 cm

36 in. 91 cm

101 in. 256 cm

126 in. 320 cm

22.9 to 48.7 feet

6.99 to 14.83 m

200 in. (161 × 118 in.) 508 cm (410 × 300 cm)

48 in. 122 cm

168 in. 427 cm

To determine the exact image size when you know the projection distance (or the exact projection distance when you know the desired image size), you can use the Image Size Calculator. This program is available on the Epson website at epson.com/support (U.S.) or epson.ca/support (Canada).

Also keep these considerations in mind:

■

Make sure there is plenty of space for ventilation around the projector. Air coming out of the ventilation slots can be quite hot. Do not place anything near the slots that can be damaged by heat.

■

Make sure the projector is within 9.8 feet (3 m) of a grounded electrical outlet or extension cord.

Setting Up the Projector

Installing the Projector

To install the projector, you first need to determine the location, based on the size of your screen (maximum diagonal image size). Use the tables on page 14 as a guide to positioning the projector.

To suspend the projector from a ceiling, you will need the optional projector mount designed for the projector. See page 10 for ordering information. Follow the instructions included with the mount to install the projector.

Warning: When installing or adjusting the ceiling mount, do not use adhesives to prevent the screws from loosening and do not use any type of oil or lubricant. These may cause the projector casing to crack and the projector may fall, causing serious injury and serious damage to the projector.

If you install the projector on the ceiling, you will need to invert the picture so that it appears right side up. Follow these steps:

1. Press the

2. Open the

3. Select

4. Press the

button on the remote control.

Settings

Front/Ceiling

button when done.

menu, then select

Projection

If you are planning to use an AV controller with the projector, refer to the table of ESC/VP21 command codes on page 74. In addition, the projector’s

Trigger out

port can be used to

lower a projection screen or operate an anamorphic lens (see page 45).

Setting Up the Projector

The following illustrations show the dimensions of the projector:

Center of lens

17.3 in. (440 mm)

8.7 in. (220 mm)

6.9 in.

174 mm

0.43 in. 11 mm

0.138 in.

12.3 in.

312 mm

6.3 in. (160 mm)

3.5 mm

2.4 in.

60 mm

3.6 in.

92 mm

1.38 in. 35 mm

0.98 in. 25 mm

180 mm

7.1 in.

7.3 in.

185 mm

15.9 in.

405 mm

7.3 in.

185 mm

M4×9mm

Setting Up the Projector

Connecting the Cables

Connecting Video and Computer Equipment

You can connect the projector to many types of video equipment, such as a Blu-ray

™

/DVD player, digital tuner, cable or satellite box, video game console, camcorder, or

Disc digital camera. You can also connect it to a desktop or laptop PC or Apple system. For details on compatible video formats, see page 71.

You can connect up to six pieces of video equipment at the same time, using any of the commercially available cables shown below:

Port name Video equipment connection Computer connection

Macintosh®

HDMI 1/ HDMI 2

Component Use a component video cable

PC — Use a Mini D-sub, 15-pin monitor cable

S-Video Use an S-video cable: —

Use an HDMI cable:

For a computer with a DVI port, you can also use a commercially available DVI-D to HDMI conversion cable.

—

(with RCA-style connectors):

Connect the cable to the three component video ports. Match corresponding colors between the cable and the ports.

to connect to a computer RGB (monitor) port:

Video Use an RCA video cable: —

Setting Up the Projector

For best results, connect your video equipment to the

HDMI

port, if possible. If your equipment doesn’t support HDMI, connect it to one of the following ports (highest quality listed first):

Connect video equipment to one of these ports

Component

(for component video),

S-Video

, or

Video

(for composite video).

Connect a computer to one of these ports

When you connect an HDMI cable to the projector, it is recommended that you fasten it as shown with one of the included cable clamps.

Making Other Connections

Connect the power cable and other cables described below, depending on how you plan to use the projector.

■

Plug the power cable into the projector and a grounded electrical outlet.

Setting Up the Projector

■

The

Trigger out

port(s) output a 12-volt DC signal when the projector is turned on. This lets a central control system monitor whether the projector is on or off, and can be used to raise or lower your projection screen automatically when the projector is in use. Depending on the setting you select (see page 45), it can also be used to operate an anamorphic lens.

Connect a 3.5-mm mini jack to the port, as shown.

■

To use an AV controller with the projector, connect a 9-pin null modem serial cable to the

RS-232C

port.

Refer to the table of ESC/VP21 command codes on page 74.

Installing Batteries in the Remote Control

The remote control uses two AA manganese or alkaline batteries.

Warning: Keep batteries away from children. If a battery is swallowed, contact your doctor immediately.

1. Release the tab and lift open the cover.

2. Insert two new AA batteries as shown.

3. Insert the tab on the cover and press it down until it clicks into place.

Aim the remote control at the screen, or at the front or back of the projector. Make sure you are within 30 feet of the projector.

If you suspect the batteries are weak, press the

illumination button. If the buttons do not glow,

replace the batteries.

Setting Up the Projector

Turning the Projector On and Off

Turning On the Projector

1. Remove the lens cap.

2. Turn on any connected equipment you plan to use.

3. Turn on the main power switch on the back of the projector.

4. Press the Ppower button on the projector or the

Note: To prevent children from turning on the projector, you can use the Child Lock feature. See page 29 for details.

If you’ll be using the projector at an altitude above 4900 feet (1500 meters), turn on High Altitude Mode so the fan can properly cool the projector at the high altitude air pressure. See page 46 for details.

button on the remote control.

Remote controlProjector

The projector takes about 30 seconds to warm up and display an image. If you don’t see a picture, you may need to change the image source as described on page 22.

Setting Up the Projector

Turning Off the Projector

1. Turn off any equipment connected to the projector.

2. Press the Ppower button on the projector or the P

Standby

button on the remote control. When you see a confirmation message, press the button again to turn the projector off.

Caution: Turn off this product when not in use to prolong the life of the projector. Continuous 24-hour-a-day use may reduce the overall life of the product.

Note: You can disable the confirmation message if you only want to press the button once to turn off the projector (see page 43).

3. If you need to move the projector, wait for the Ppower light to stop flashing, then turn

off the projector’s main power switch on the back. You can now unplug the projector.

Caution: Never turn off the main power switch without first turning off the projector and letting it cool as described above, or you could damage it and reduce lamp life.

Selecting the Image Source

The source buttons on the projector and remote control let you switch between images from different pieces of equipment connected to the projector (such as a DVD player, cable or satellite box, or video game console).

Press the video source is connected.

Source

button on the remote control that corresponds to the port to which your

Setting Up the Projector

If you press the source button on the projector, you see a list of available sources. Press the source button to move through the list and select the desired source.

Note: If an image does not appear, see “Problem Solving” on page 61.

To temporarily turn off the image and darken the screen, press the Blank button on the remote control. Press the Blank button again to return to normal viewing.

Positioning the Image

You can display a test pattern to help adjust the image position by pressing the button on the remote control. Select

Display Position

button to turn off the test pattern. You can also use the

, then press

Pattern

button to isolate colors when

Enter

Pattern

. Press the

Esc

displaying color bars (see page 36).

If the image is not centered on the screen, use the lens shift function, as described below, to adjust its position.

■

If the image looks like or , make sure the projector is not tilted up or down. Instead, keep the projector level, then use the lens shift to position the image on the screen.

■

If the image looks like or , the projector has been placed off to one side of the screen and angled toward it. Instead, face the projector straight ahead, then use the lens shift to center the image.

Setting Up the Projector

To use the lens shift, press the

Lens Shift

button on the remote control, then use the

lrud arrow buttons to adjust the image position. To return the lens to the center, press and hold any arrow button until the lens moves to the center and stops.

Caution: Do not try to move the lens by hand, or you may damage the projector. Always use the lens shift function to change the lens position.

The amount by which you can shift the image is expressed in terms of the horizontal (H) and vertical (V) image size, as shown below:

Maximum lens shift boundary

Note that the image cannot be moved to the maximum distance in both the vertical and horizontal directions at the same time. For example, when the image has been shifted horizontally by the full amount, it can be shifted vertically by only 9 percent of the height of the image.

If the image is centered on the screen but one side is taller than the other, adjust the front feet so that the projector is level.

Setting Up the Projector

Making Basic Adjustments

Follow the instructions in this chapter to make basic adjustments to the image shape, size, color, and quality. For further refinements, see “Making Detailed Adjustments” on page 31.

Focusing and Zooming

To focus the image, press the arrow buttons to adjust the picture.

To adjust the image size, press the arrow buttons to reduce or enlarge the picture.

Focus

button on the remote control, then use the l and r

Zoom

button on the remote control, then use the l and r

Making Basic Adjustments

Choosing the Aspect Ratio

In many cases, video signals are automatically resized to fit on your screen when need to change the size of the image (or aspect ratio) for certain image types by pressing the

Select one of these settings (some settings may not be available, depending on the input sigal):

Auto

is selected as the Aspect setting. You may

Aspect

button on the remote control.

■ Normal

for HDTV (16:9 aspect ratio), computer images, or

images recorded at a 4:3 aspect ratio.

4:3 image using Normal settingHDTV (16:9) image using Normal setting

■ Full

for images recorded in squeeze mode (using horizontal compression). 4:3 images not

recorded in squeeze mode are stretched to fit the screen.

■ Zoom

■ Wide

for images recorded in letterbox format. Fits the image to the screen.

Note: Depending on the image’s aspect ratio, the top and bottom may be hidden from view. Use the Zoom Size option to adjust the image vertically. If subtitles aren’t visible, use Zoom Caption Pos. to reposition the image. See page 43.

to expand a 4:3 image to 16:9 so it fills the whole screen. This stretches only the

right and left sides of the image; the central part is unchanged.

■ Anamorphic Wide

CinemaScope

to display images that have a 2.40:1 aspect ratio (such as

) when using a commercially available anamorphic lens (available from

Epson—see page 10).

Note: If you use this setting without an anamorphic lens, the image fills the screen vertically but not at the correct aspect ratio. Make sure Overscan is set to Off (100%), or the image won’t display correctly (see page 42). If your anamorphic lens has a motorized transport, you can operate it automatically with the Trigger out port (see page 45).

■ Horiz. Squeeze

equipped the projector with a fixed anamorphic lens.

Making Basic Adjustments

to display images that have a 16:9 or 4:3 aspect ratio when you’ve

+ 58 hidden pages