Eneo HDD-20, PTZ1080, HDD-2020PTZ1080 Installation Manual
1/2.8 HD SDI Dome, PTZ, 18x, Day&Night
HDD-20PTZ1080
Installation Guide
2
Contents
Part 1 – Installation Guide ............................................................................ 3
Part 2 – User Manual .................................................................................. 36
Part 3 – OSD Manual ................................................................................... 62
Installation Guide
3
Part 1
Installation Guide
Version 1.2
Installation Guide
4
Table of Contents – Part 1
1. Introduction ........................................................................................................................... 5
2. Standard Package Contents ................................................................................................. 6
3. Camera Setups and Cable Connections .............................................................................. 7
3.1 Dome Camera Setups ................................................................................................. 7
3.1.1 Switch/Connector Definition ......................................................................... 8
3.1.2 Communication Switch Setting ..................................................................... 8
3.1.3 ID Setup ....................................................................................................... 9
3.1.4 Camera Control Protocol Setting ................................................................ 10
3.2 Cables and Connections ............................................................................................ 11
3.2.1 Power Connection ...................................................................................... 11
3.2.2 Apply Alarm I/O Definition .......................................................................... 11
3.2.3 RS-485 Connector Definition ...................................................................... 12
4. Dome Camera Installation .................................................................................................. 13
4.1 Camera Dimensions .................................................................................................. 13
4.2 Optional Accessories ................................................................................................. 14
4.3 Ceiling Mount with Straight Tube ............................................................................... 20
4.4 Wall Mount ................................................................................................................ 22
4.4.1 Compact Pendent Mount ............................................................................ 22
4.4.2 Standard Pendent Mount ............................................................................ 22
4.4.3 Wall Box Mounting ..................................................................................... 24
4.5 Corner Mount ............................................................................................................. 28
4.5.1 Corner Standard Mounting Plate/Corner Plate Mini .................................... 28
4.5.2 Corner Thin/Wide Box Mounting ................................................................. 30
4.6 Pole Mount ................................................................................................................ 32
4.6.1 Pole Thin/Wide Direct Mounting ................................................................. 32
4.6.2 Pole Thin/Wide Box Mounting .................................................................... 34
Installation Guide
5
1. Introduction
The SDI Speed Dome Camera is designed to deliver superb performance and
durability with an intelligent and stylish housing that is suitable in any security
and surveillance installation.
Installation Guide
6
2. Standard Package Contents
Before proceeding, please check the box contains the items listed here. If any
item is missing or has defects, DO NOT install or operate the product and
contact your dealer for assistance.
Outdoor Model
Camera Body with
Outdoor Mount Kit
M3 Standard Screw (x1)
M3 Security Screw (x1)*
M5 Standard Screw (x1)
M5 Security Screw (x1)*
Waterproof Rubber
Quick Guide
CD: Operation Manuals
Optical Cover
Lubricant
Security Torx*
*Optional: For Vandal Proof Cover only.
Installation Guide
7
3. Camera Setups and Cable Connections
Before installing or connecting the Dome Camera, please refer to this section
and complete preparations for dome setups and various switch settings.
There will be a PE cloth sheet covered inside the dome cover and a lens cap
on the lens for shipping protection. Follow the steps below to remove those
protective materials.
Step 1: Unpack the dome package and take out the dome body.
Step 2: Rotate and remove the protective cover.
Step 3: Remove the PE cloth sheet and take off the lens cap.
Step 4: Attach the dome cover to the dome body.
3.1 Dome Camera Setups
Before connecting the Dome Camera to other devices, please complete the
Dome Camera’s ID and communication switch setting. These switches are
located on the rear plate of the Dome Camera.
Installation Guide
8
3.1.1 Switch/Connector Definition
There are various connectors located on the Dome Camera’s back plate as
shown in the figures below. Please refer to the diagrams and tables
accompanied with for use of each switch/connector.
3.1.2 Communication Switch Setting
The analog Dome Camera’s communication switches are specified in the table
below.
Communication Switch
SW 1
RS-485 Setting
SW 2
SW 3
SW 4
SW 5
Reserved
SW 6
Reserved
Item Definition Remark
A
I/O
ALARM I/O
B
ID Dome Camera ID Setup DIP Switch
C
SDI SDI signal output
D
SETTING Communication Switch Setting
E
Protocol Camera Control Protocol Setting
F
RS485 RS485 Connector
G
AC24V Connector Power connector
Installation Guide
9
RS-485 is the interface that communicates the Camera and its control device;
for this reason, the RS-485 setup of the Camera and the control device must
be the same. The RS-485 default setting is half-duplex (see the diagram
follows). Please do not change the default setting without qualified specialist or
supplier’s notice.
RS-485 Setting
Half-duplex
Full-duplex
3.1.3 ID Setup
Please assign an ID number to a Camera if there is more than one Camera in
the same network. The camera’s ID can be setup using the 10-bit ID Dip
Switch, which is located on the Camera’s back plate. If the Camera’s ID
number is 6, for instance, the ID switch SW 2 and SW 3 should be set to “ON”
and the rest should be set to “OFF” as shown below. Dip Switch configuration
for ID No. 0~10 are listed in the table below. To complete ID setups, please
refer to the User Manual (up to page36).
For switch configuration details, please refer to User Manual > Appendix B:
Switch Settings Index Table.
NOTE: No two Cameras should be given the same ID, or
communication conflict may occur.
Installation Guide
10
3.1.4 Camera Control Protocol Setting
Define the protocol you are going to use basing on the devices of your
surveillance system. Generally, use one protocol even the devices are
provided from different manufacturers. Please refer to the table below for all
supported protocols with their matching switch numbers and baud rate and
choose a protocol for your Camera. The table below shows various protocols
with their matching switch numbers and baud rate.
Switch No. Protocol Baud Rate
00
VCL 9600
01
Pelco D 2400
02
Pelco P 4800
04
Chiper 9600
05
Philips 9600
07
DSCP 9600
08
AD422 4800
09
DM P 9600
11
Pelco D 4800
12
Pelco D 9600
13
Pelco P 2400
14
Pelco P 9600
15
JVC 9600
21
Kalatel-485 9600
22
Kalatel-422 4800
Use the 6-bit dip switch (Camera Control Protocol Switch) to set your camera’s
control protocol and its baud rate. If select protocol “Pelco D”, which is of
switch no. 01 and baud rate 2400, for instance, set the SW-1 to “ON,” with the
rest to “OFF” as shown below.
For switch configuration details, please refer to User Manual > Appendix B:
Switch Settings Index Table.
Installation Guide
11
3.2 Cables and Connections
For operation, the Dome Camera requires power cable and RS485 as
described below:
3.2.1 Power Connection
Please refer to the illustrations below to connect power core through the
supplied power adaptor.
SW 1
AC24V_1
SW 2
GND
SW 3
AC24V_2
3.2.2 Apply Alarm I/O Definition
The Camera supports 4 digital alarm inputs and 2 digital alarm outputs. Please
make sure the alarm connections are properly wired before starting to
configure alarm related settings. Please refer to the pin definition table below
for alarm system wiring.
Pin Definition Pin Definition
12
ALM_IN_1
6
ALM_OUT_NC_2
11 ALM_IN_2 5 ALM_OUT_NO_2
10 A
LM_IN_3
4
GND
9
ALM_IN_4
3
ALM_OUT_COM_1
8
GND
2
ALM_OUT_NC_1
7
ALM_OUT_COM_2
1
ALM_OUT_NO_1
Installation Guide
12
3.2.3 RS-485 Connector Definition
Please refer to the illustrations below for RS485 connector definition before
wiring.
RS485
Connector
SW 1
R-
SW 2
GND
SW 3
R+
SW 4
T-
SW 5
T+
Installation Guide
13
4. Dome Camera Installation
Basing on user’s installation environments, the Dome Camera can be installed
on ceiling, on wall or on pole. In the following sections, various Dome Camera
installation accessories, installation methods and installation procedures will
be described in detail. In addition, the next section will provide the Dome
Camera’s dimensions for your reference before installation.
4.1 Camera Dimensions
The Dome Camera’s dimensions are as below show detailed dimensions for
the Dome Camera’s different parts.
Dimensions: mm
192
282.4
103.473.5 35.8
44.5
Installation Guide
14
4.2 Optional Accessories
Dome Camera Accessories
Transparent/Vandal Proo f
Transparent Cover (Standard)
Vandal Proof Cover (Optional)
Mounting Accessories
Standard Pendent Mount (Art. No. 200825)
White; 348×104×138.6 mm (13.7×4.1×5.5 inches); 1.5 kg (3.3 lbs); Diameter: 45
mm (1.8 inches). Supplied with M8x12 screw x1, spring washer-8 x1, pendent
tube washer x1, rubber washer-8 x1 and sponge x2.
Dimensions: mm
Maße/Dimensions: mm
138.6
348
98.5
81
104
Installation Guide
15
Compact Pendent Mount (Art. No. 200826)
184×104×127 mm (7.24×4.09×5 inches); 0.6 kg (1.2 lbs)
Supplied with rubber washer-8 x1, pendent tube washer x1, spring washer-8 x1
and M8x12 screw x1.
Dimensions: mm
Straight Tube (Art. No. 200827)
Iron, Height: 250 mm (9.8 inches) ,Diameter: 50 mm (2 inches)
1 kg (2.2 lbs), Supplied with M8x12 screw x1, spring washer-8 x1, pendent tube
washer x1, rubber washer-8 x1 and waterproof rubber x1.
Dimensions: mm
127
184
115.2
12.5
88.9
76.2
4x 8.5
104
45.2
250
50
100
140
100
4x 8.5
Installation Guide
16
Corner Plate Mini (Art. No. 200831)
For mounting with Compact Pendent Mount.
200(L)×90(H)×117(D) mm (7.87×3.54×4.6 inches);
Supplied with washer-8 x4, spring washer-8 x4, M8x16 screw x4 and M8 nut x4.
Dimensions: mm
Corner Standard Mounting Plate (Art. No. 200830)
204(L)×222(H)×117(D) mm (8×8.74×4.6 inches); 2 kg (4.4 lbs);
Supplied with washer-8 x4, spring washer-8 x4, M8x16 screw x4, and M8 nut x4.
Dimensions: mm
90°
65
68
25
117
78.5
81
11.5
8x 8.5
54
112
90
200
90°
112
117
190
81
10x 8.5
54
98.5
67
222
204
Installation Guide
17
Pole Thin Direct Mounting (Art. No. 200834)
232(H)×136(W)×50(D) mm (9.1×5.4×2 inches); Diameter: 112~130 mm (4.4~5
inches); 0.7 kg (1.6 lbs). Supplied with stainless steel straps x4, M8x16 screw x4,
washer x4 and spring washer-8 x4.
Dimensions: mm
Corner Wide Box Mounting (Art. No. 200832)
232(H)×234(W)×208(D) mm (9.1×9.2×8.2 inches); 2.7 kg (6 lbs); Supplied with
M8x16 screw x4, washer-8 x4, and spring washer-8 x4.
Power Box can be set inside the wide box.
Dimensions: mm
190
8x 8.5
60
98.5
67
232
136
26
54
50
90°
45
175
20
208
190
8x 8.5
65
98.5
67
232
170
140
4x 16
234
Installation Guide
18
Pole Wide Box Mounting (Art. No. 200835)
270(H)×170(W)×155(D) mm (10.6×6.7×6.1 inches); 3.2 kg (7.1 lbs); Supplied with
M8x16 screw x4, washer-8 x4, spring washer-8 x4 and stainless steel straps x4.
Power Box can be set inside the wide box.
Dimensions: mm
Wall Box Mounting (Art. No. 200829)
270(H)×170(W)×95(D) (10.6×6.7×3.7 inches); 2.2 kg (4.84 lbs);
Supplied with M8x16 screw x4, washer-8 x4 and spring washer-8 x4
Power Box can be set inside the wall box.
Dimensions> mm
190
8x 8.5
65
98.5
67
232
81
100
170
270
55
12.5
95 60
190
8x 8.5
65
98.5
67
232
81
100
170
270
95
Installation Guide
19
Stainless Steel Straps
For fixing Pole Direct Mounting / Pole Box on the pole.
Length: 650mm (25.6 inches); Width: 12.7mm; Weight: 50g (0.1 lb)
All photos of the accessories are subject to change without notice.
Installation Guide
20
4.3 Ceiling Mount with Straight Tube
The Straight Tube is available in different length: 25cm and 50cm.
Package Contents:
z
M8x12 Screw x1
z
Spring Washer-8 x1
z
Pendent Tube Washer x1
z
Rubber Washer-8 x1
z
Waterproof Rubber x1
Items Needed:
z
Dome Camera
z
Power Cable
z
Ethernet Cable
z
Straight Tube
z
Screws and Screw Anchors for fixing the Straight Tube onto the ceiling
Tools Needed:
z
Tool for drilling
z
Tool for screwing
Follow the steps to mount the Dome Camera with the Straight Tube.
1) Ensure that the ceiling can support the weight of the Dome Camera and
Straight Tube.
2) Make a cable entry hole on the ceiling.
3) Fix the suspension bracket to the ceiling with proper screws and screw
anchors.
4) Thread the cables through the Straight Tube and the Mounting kit.
NOTE : After threading the cables, please block the cable entry
hole with the supplied sponge(s) to avoid insects entering the tube.
5) Fix the Mounting Kit to the Straight Tube with the supplied screws and
washers.
6) Connect the cables to the Dome Camera.
Installation Guide
21
7)
Mount the Dome Camera to the Mounting Kit.
(Ensure the Dome Camera is fixed
completely, and the thread holes on the Lock
Screw Plate and Mounting Kit are aligned).
Afterwards, screw the supplied M5 standard
screw / security screw, as shown in the
picture.
Ceiling Mounting: Straight Tube
Installation Guide
22
4.4 Wall Mount
The Dome Camera can be mounted on the wall with Compact Pendent Mount,
Standard Pendent Mount and Wall Box. Please follow the installation
instructions below for mounting the Dome Camera via different ways.
4.4.1 Compact Pendent Mount
Package Contents:
z
Rubber Washer-8 x1
z
Pendent Tube Washer x1
z
Spring Washer-8 x1
z
M8x12 Screw x1
Items Needed:
z
Dome Camera
z
Power Cable
z
Ethernet Cable
z
Compact Pendent Mount and equipped items (optional accessory)
z
Mounting Kit
z
Waterproof Rubber
z
Screws and Screw Anchors for fixing the Compact Pendent Mount
Tools Needed:
z
Tool for drilling
z
Tool for screwing
Follow the steps below to mount the Dome Camera with the Compact Pendant
Mount.
1) Make a cable entry hole on the wall to recess the cables. Otherwise, users
could push up the Cable Entry Board on the Compact Pendent Mount’s
Mounting Plate to place the cables, as shown in the photo below.
Cable Entry
Mounting
Installation Guide
23
2) Fix the Compact Pendent Mount on the wall with proper screws and screw
anchors.
3) Attach the Waterproof Rubber to the Compact Pendent Mount.
4) Run the cable(s) through the Compact Pendent Mount.
NOTE: Please block the cable entry hole with the supplied sponge
to avoid insects entering the Pendent Mount. The sponge can be
placed in two ways as shown in the illustrations below.
5) Thread the cable(s) through the Mounting Kit and join the Mounting Kit to
the Compact Pendent Mount with the supplied screws and washers.
Then adjust the Waterproof Rubber to the joint.
6) Connect the cable(s) to the Dome Camera.
7) Join the Dome Camera to the Mounting Kit with the supplied screw and
washers.
Wall Mounting: Compact Pendent Mount + Mounting Kit
Sponge
Sponge
Installation Guide
24
4.4.2 Standard Pendent Mount
Package Contents:
z
M8x12 Screw x1
z
Spring Washer-8 x1
z
Pendent Tube Washer x1
z
Rubber Washer-8 x1
z
Sponge x2
Items Needed:
z
Dome Camera
z
Power Cable
z
Ethernet Cable
z
Standard Pendent Mount and equipped items (optional accessory)
z
Mounting Kit
z
Waterproof Rubber
z
Screws and Screw Anchors for fixing the Standard Pendent Mount onto the
ceiling
Tools Needed:
z
Tool for drilling
z
Tool for screwing
Follow the steps below to mount the Dome Camera with the Standard Pendent
Mount.
1) Make a cable entry hole on the wall to recess the cables. Otherwise, users
could push up the cable entry board on the Standard Pendent Mount’s
mounting plate to place the cables (refer to the illustration below.
2) Fix the Standard Pendent Mount on the wall with proper screws and screw
anchors.
3) Attach the Waterproof Rubber to the Standard Pendent Mount.
4) Run the cable(s) through the Standard Pendent Mount.
NOTE: Please block the cable entry hole with the supplied sponge
to avoid insects entering the Pendent Mount. Refer to the
illustration below.
Installation Guide
25
5) Thread the cable(s) through the Mounting Kit and join the Mounting Kit to
the Standard Pendent Mount with the supplied screws and washers.
Then adjust the Waterproof Rubber to the joint.
6) Connect the cable(s) to the Dome Camera.
7) Join the Dome Camera to the Mounting Kit with the supplied screw and
washers.
Wall Mounting: Standard Pendent Mount + Mounting Kit
Installation Guide
26
4.4.3 Wall Box Mounting
Package Contents:
z
M8x16 Screw x4
z
Washer-8 x4
z
Spring Washer-8 x4
Items Needed:
z
Dome Camera
z
Power Cable
z
Ethernet Cable
z
Standard/ Compact Pendent Mount and equipped items (optional
accessory)
z
Wall Box Mounting (optional accessory)
z
Mounting Kit
z
Waterproof Rubber
z
Screws and Screw Anchors for fixing the Wall Box Mounting onto the ceiling
Tools Needed:
z
Tool for drilling
z
Tool for screwing
Follow the steps to mount the Dome Camera with the Standard/ Compact
Pendent Mounting and Wall Box Mounting.
1) Make a cable entry hole on the wall to recess the cable(s).
2) Fix the Wall Box Mounting on the wall with proper screws and screw
anchors. Then run the cable(s) through the hole on the Wall Box Mounting.
3) Fasten the Standard/ Compact Pendent Mount onto the Wall Box Mounting
with the supplied screws and washers. Then thread the cable(s) through the
Standard/ Compact Pendent Mount with the cable(s) coming out of the
Pendent Mount’s outlet.
NOTE: Please block the cable entry hole with the supplied sponge
to avoid insects entering the Pendent Mount. Refer to the
illustration in section 4.4.2 Compact Pendent Mount > Step 4.
4) Attach the Waterproof Rubber to the Standard/ Compact Pendent Mount.
Installation Guide
27
5) Thread the cable(s) through the Mounting Kit and join the Mounting Kit to
the Standard/ Compact Pendent Mount with the supplied screws and washers.
Then adjust the Waterproof Rubber to the joint.
6) Connect the cable(s) to the Dome Camera.
7) Join the Dome Camera to the Mounting Kit with the supplied screw and
washers.
Wall Box Mounting:
Wall Box Mounting + Standard/Compact Pendent Mount + Mounting Kit
Installation Guide
28
4.5 Corner Mount
4.5.1 Corner Standard Mounting Plate/Corner Plate Mini
Package Contents:
z
Washer-8 x4
z
Spring Washer-8 ×4
z
M8x16 Screw x4
z
M8 Nut x4
Items Needed:
z
Dome Camera
z
Power Cable
z
Ethernet Cable
z
Standard/Compact Pendent Mount and equipped items (optional
accessory)
z
Corner Standard Mounting Plate/Corner Plate Mini (optional accessory)
z
Mounting Kit
z
Waterproof Rubber
z
Screws and Screw Anchors for fixing the Corner Mounting Plate
Tools Needed:
z
Tool for drilling
z
Tool for screwing
Follow the steps below to mount the Dome Camera with the Corner mounting
Plate and Standard/ Compact Pendent Mount.
1) Make a cable entry hole on the wall to recess the cable(s).
2) Fix the Corner Mounting Plate on the corner of the wall with proper screws
and screw anchors. Then run the cable(s) through the hole on the Corner
Mounting Plate.
3) Fasten the Standard/ Compact Pendent Mount onto the Corner Mounting
Plate with the supplied screws and washers. Then thread the cable(s)
through the Standard/ Compact Pendent Mount with the cable(s) coming out
of the Pendent Mount’s outlet.
Loading...