Eneo HDB-2080M2810IR D User Manual

Quick Installation Guide

1/3” HDcctv Camera, 3D-DNR,
Day&Night, 1920x1080, 2.8-

EN

10mm, RS-485, infrared,
12/24V

HDB-2080M2810IR D

FULL-HD MEGA-PIXEL CAMERA

Safety Precaution

To prevent fire or shock hazard, do not expose the unit to rain or moisture.
To prevent electric shocks and risk of fire hazards, do NOT use other than
specific power source.

CAUTION: TO REDUCE THE RISK OF ELECTIC SHOCK,
DO NOT REMOVE COVER (OR BACK).
NO USER SERVICEABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.

The symbol is intended to alert the user to the presence of uninsulated
"dangerous voltage" within the product's enclosure that may be of
sufficient magnitude to constitute a risk of electric shock to persons.

The symbol is intended to alert the user to the presence of important
operating and maintenance(servicing) instructions in the literature
accompanying the unit.

Warning :

This equipment has been tested and found to comply with the limits for a Class

A digital device, pursuant to part 15 of the FCC Rules. These limits are designed
to provide reasonable protection against harmful interference when the equipment
is operated in a commercial environment. This equipment generates, uses, and
can radiate radio frequency energy and, if not installed and used in accordance with
the instruction manual, may cause harmful interference to radio communications.
Operation of this equipment in a residential area is likely to cause harmful
interference in which case the user will be required to correct the interference at
his own expense.

Caution :
Any changes or modifications in construction of this device which are not expressly
approved by the party responsible for compliance could void the user's authority
to operate the equipment.
Mains power quality should be that of a typical commercial environment. If the user
of the model requires continued operation during power mains interruptions, it is
recommended that the model be powered from an uninterruptible power supply
(UPS) or a battery.

03

FULL-HD MEGA-PIXEL CAMERA

Safety Precaution

NOTICE

The image used in this instruction manual are processed to help comprehension
and may differ from actual video of the camera.
Avoid installing areas where has shock or vibration which results in the problems.

Pay attention to safety when laying the connection cable and observe that the cable
is not subjected to heavy loads, kinks or damage and no moisture can get in.
Never open the device such as boards or lens.
The warranty becomes void if repairs are undertaken by unauthorized persons.
Maintenance and repair have to be carried out only by authorized service centers.
Use only a mild detergent to clean the housing.
The camera should never be operated beyond the technical specifications.
This can lead to destruction.
The camera should never be operated in water.

04

FULL-HD MEGA-PIXEL CAMERA

Contents

p.03~04

Safety Precaution

p.05

Contents

p.06~07

Features

p.07

Composition

p.08

Dimensions

p.09

Part Names

p.10~12

Installation Instructions

p.13~29

Operating Instructions

p.30~31

Specifications

05

FULL-HD MEGA-PIXEL CAMERA

Features

Key Features

• Full HD, 2Mega Pixel EX-SDI CAMERA, 1920x1080(30p/25p)

• Extended long reach HD Solution

• Real time True WDR(Wide Dynamic Range) / 30fps

• Improved noise figure with the enhanced 3DNR

• Built-in f=2.8~10mm F1.4, Mega-pixel DC Auto Iris vari-focal lens

• Dual Filter Switcher

• Day & Night Simulation for easy focus adjustment

• Various Zooming Technologies

- Pointing Zoom (which enables the programmable zooming at any area)

- Preset Zoom

- Flex Zoom

- Smart Motion Zoom (Automatic zoom in/out when motion is detected)

• Motion Detection, Privacy Mask, Defog, Sens-up(~x32), D-WDR,

H/V/HV Flip, D-Zoom(~8x), Lens Shade Compensation, BLC/HLC,

Pixel Defect Compensation, Title Set

• EX-SDI or HD-SDI switchable

• Top performance at low light sensitivity (Sens-up On)

• OSD menu & CVBS Video output BNC for easy installation & maintenance.

• Circuit protection against faulty connection in power polarity

• Isolated power supply against ground loop problem

• Remote control via RS-485 (Pelco-D/P)

• Quick Firmware update via RS-485

• Operable up to -50ºC

• External Zoom & Focus adjustment

• Built-in 40pcs LEDs

• LED ON/OFF Control

• Dual Window

• Built-in Heating function

• One-touch 3-Axis locking bracket, Easy Installation Pad

• IP67 protection

06

FULL-HD MEGA-PIXEL CAMERA

Features

General Description

This camera realizes the natural and crisp image as you see the scene in front
of you by Full HD(1920x1080p) camera module.
Highly detailed pictures can be achieved and color reproducibility deserves
attention.

• With ICR mechanism,

- Enhances its sensitivity about 10x at night time

- Can accepts the infrared light

• With Intelligent Focus Indicator and FOCUS ASSIST menu,

- Offers easy adjustment of Focus

- Eliminates the mistake of the erratic focus adjustment

• With 24VAC/12VDC dual power design,

- Offers the flexibility of installation

- Ensures the reliability

Composition

Plastic Anchor:

6 x 30mm (4pcs)

Camera

Cable Signal
Sticker

Operating
Instruction

Mounting Template

Mounting Screw:
4 x 30mm (4pcs)

Assembly Screw:

4 x 14mm (4pcs)

Torque Wrench:

3mm (1pc)

Wiring Connector:

Video Sub-out
Cable (1pc)

07

(1pc)

Easy
Bracket

FULL-HD MEGA-PIXEL CAMERA

Dimensions

(unit : mm)

100

86.40

75.90

190

267

80

87.30
108

CAUTION

• Extreme care should be taken NOT to scratch the window in front of lens.

• Care should be taken the cable is NOT to be damaged, kinked or exposed
in the hazardous area.

• Do not expose the camera directly to a strong light source such as the sun
or spot light.

08

FULL-HD MEGA-PIXEL CAMERA

Part Names

SUNSHIELD BOLT

SUNSHIELD

DUAL WINDOW

FRONT CASE

REAR CASE

OSD Setup

CONTROL COVER

LOCK/UNLOCK
SCREW

POWER CABLE

BRACKET

EASY
BRACKET

FOCUS ZOOM

REAR VIEW

Torque
wrench

Lock/Unlock
Screw

■ Adjustment of viewing angle with a bracket

09

FULL-HD MEGA-PIXEL CAMERA

Installation Instructions

1. Locate the mounting template at the installation position and drill the ceiling or
wall if needed. ( *The easy bracket can not be installed on the ceiling)

2. Place the easy bracket on pre-drilled position and fix it through using mounting
screws (4x30mm). Skip this step when an easy bracket is not installed.

3. Route the Power cable to the connecting place.
Hook up the camera bracket with the easy bracket as illustrated below.

4. Fix the camera bracket through using assembly screws (4x14mm).

5. Set the camera’s viewing angle and adjust zoom/focus of lens by using the torque
wrench.

6. Put the sunshield to the camera unit and tighten the sunshield-bolts.

Assembly Screw
: 4x14mm

Torque Wrench

Mounting Screw
: 4x30mm

4

REAR VIEW

1

2

3

Cable exit

10