Eneo HDB-1080Z03IR D User Manual [en, de, fr]

Quick Installation Guide

1/3” HDcctv Camera, WDR, Day&Night, 1920x1080, 3-9mm, 3x AF Zoom, infrared,

12/24V

HDB-1080Z03IR D

Table of content

Notes on safety .............................................................................................................3

Parts supplied ...............................................................................................................3

Part names .....................................................................................................................4

Installation instructions ...............................................................................................5

Pan & Tilt adjustments ..................................................................................................................................................... 6

Power supply connections .............................................................................................................................................7

Operating instructions .................................................................................................9

Using OSD controller........................................................................................................................................................9

Description of the joystick operation ..........................................................................................................9

Description of the ZOOM&FOCUS adjustment .......................................................................................9

Set the video format according to system, EX-SDI or HD-SDI ........................................................................ 10

OSD menu startup ......................................................................................................................................................... 10

Direct control menu ...................................................................................................................................................... 11

Further information ....................................................................................................11

Notes on safety

Please also pay attention to the enclosed safety instructions, and carefully read through this instruction guide before initial operation.

Important points of warning are marked with a caution symbol.

Important points of advice are marked with a notice symbol.

Parts supplied

• Camera

• Cable Signal Sticker

• Operating Instruction

• Mounting Template

• Easy Bracket

• Assembly Screw: 4 x 14mm (4x)

• Plastic Anchor: 6 x 30mm (4x)

• Mounting Screw: 4 x 30mm (4x)

• Torque Wrench: 3mm (1x)

• Wiring Connector: (1x)

• Video Sub-out Cable (1x)

Part names

Dual window

Power cable

OSD setup control cover

Easy bracket

Bracket

Front case

Rear case

Installation instructions

CAUTION: The camera’s base should be attached to a structural

object, such as concrete, hard wood, wall stud or ceiling rafter that supports the weight of the camera. If necessary use appropriate mounting material (e.g. anchors) instead of the material enclosed with the camera.

1. Locate the mounting template at the installation position and drill the ceiling or wall if needed.

2. Place the easy bracket on pre-drilled position and x it through using mounting screws (4x35mm). Skip this step when an easy bracket is not installed.

3. Route the power cable to the connecting place. Hook up the camera bracket with the easy bracket as illustrated below.

4. Fix the camera bracket through using assembly screws (4x12mm).

5. Set the camera’s viewing angle.

Assembly Screw: 4x12mm

The easy bracket can not be installed on the ceiling.

Mounting Screw: 4x35mm

Torque Wrench

Cable exit

CAUTION:

Extreme care should be taken NOT to scratch the window in front of lens.

Care should be taken the cable is NOT to be damaged, kinked or exposed in the hazardous area.

Do not expose the camera directly to a strong light source such as the sun or spot light.

Pan & Tilt adjustments

• Unlock the screw on the camera bracket through using the torque wrench supplied

• Set the camera’s viewing angle then lock the screw on the bracket.

Adjustment of viewing angle with a bracket

Lock/Unlock Screw

Torque wrench

1. Pan limit: Pan is limited to +/- 80°.

80° 80°

160°

2. Tilt limit: Tilt is limited to 0° min ~ 90° max. for wall(ceiling) installation respectively with reference to the wall(ceiling) when the inclination of camera module is 0°, that is, the image is aligned horizontally.

90°

3. Inclination limit (Horizontal image alignment): Inclination limited to +/-90° max.

±90°

Power supply connections

Make sure the power is removed before the installation. Camera can work with either 24AC or 12VDC, dual voltage power. Primary and secondary grounds are completely isolated to avoid the possible ground-loop problems.

In case that HD-SDI/EX-SDI Inputs are not supported in monitor, please use HD-SDI/ EX-SDI Converter to connect HD-SDI/EX-SDI cable with monitor. Some computer monitors or TVs may not support 30p/25p. In this case, HD-SDI/EX-SDI DVR which can convert the frame rate to 60p/50p is highly recommended. Please check specication of monitor before installation.

VIDEO (BNC)

AC24V/DC12V (Red wire)

AC24V/GND (Black wire)

RTX+/RS485 (White wire)

RTX-/RS485 (Gray wire)

Attach the Signal Assignment Sticker in a visible spot for wiring reference.

Operating instructions

Using OSD controller

Setup menu can be accessed and controlled by OSD control joy stick on the side of camera unit. Five commands are available with the joy stick.

OSD Control Joy Stick

Cover Open

Video format Switch

Video Sub-out Connector

Description of the joystick operation

1. SET Key (●) : Access to the menu or enter the setting. To enter the main menu, press the Set Key down for about 1.5sec

2. UP/DOWN Key (▲/▼) : Choose the desired sub-menu and to move the cursor up or down.

3. LEFT/RIGHT Key (◄/►) : Set up the value of the selected menu. Used to adjust the desired menu selection and to move the cursor left or right.

4. ‘☟’ denotes the long press down straightly for about 2 seconds

Description of the ZOOM&FOCUS adjustment

Works only when OSD Menu is inactive.

1. ▲ : Zoom In

2. ▼ : Zoom Out

3. ◄ : Focus Near

4. ► : Focus Far

Set the video format according to system, EX-SDI or HD-SDI

To select the camera’s output video format (EX-SDI or HD-SDI), use the Video format Switch on the side of the camera. Only one format can be used at a time (see also “Using OSD controller”).

1M~120M via RG59u or 5C2V cable

Camera (HD-SDI)

1M~120M via RG59u or 5C2V cable

Camera (HD-SDI)

1M~120M via RG59u or 5C2V cable

Camera (HD-SDI)

Camera (EX-SDI)

Camera (EX-SDI) DVR (EX-SDI)

HDA-3000E (HD-SDI)

HDA-3000E (EX-SDI)

350M+ via RG59u or 5C2V cable

1M~120M via RG59u or 5C2V cable

350M+ via RG59u or 5C2V cable

HDA-3000E (HD-SDI)

HDA-3000E (EX-SDI)

1M~120M via RG59u or 5C2V cable

DVR (HD-SDI)

OSD menu startup

Press ‘●’ (OSD menu Joy stick key) down for about 2 seconds to access the setup menu mode.

Lens Initializing is strongly recommended at the rst stage of setup menu control.

ZOOM/FOCUS > LENS INIT > Press the joystick ‘☟’ straight down for about 2 seconds.

MENU V5.xx

1. ZOOM/FOCUS

2. EXPOSURE

3. SCENE ENHANCE

4. 3D-NR

5. DAY/NIGHT

6. PICT ADJUST

7. SPECIAL

8. SYSTEM

9. EXIT

↵

NORMAL MID EXT

↵

SAVE&EXIT

↵

Direct control menu

MAIN DEFAULT DESCRIPTION ZOOM/FOCUS - Sets FOCUS and ZOOM relative fuctions. EXPOSURE - Sets EXPOSURE MODE, BRIGHTNESS, SENS-UP, AGC and MOTION DEBLUR.

SCENE ENHANCE NORMAL

3D-NR MID Sets 3DNR level. LOW, MID, HIGH

DAY/NIGHT EXT or AUTO

PICT ADJUST Sets WHITE BAL, SHARPNESS, COLOR GAIN, GAMMA

SPECIAL

SYSTEM

EXIT

SCENE ENHANCE provides the several ways to enhance the video in the various environments with the settings in NORMAL, WDR, D-WDR, BLC and HLC.

Sets DAY / NIGHT to EXT, AUTO, COLOR, B/W and COLOR D/N. Setting EXT mode for cameras with IR-LED, AUTO mode for none IR-LED camera types.

Sets MIRROR/FLIP, PRIVACY, MOTION, PIXEL DEFECT, TITLE SET, DISPLAY, DEFOG, POINTING ZOOM

Sets TV SYSTEM, RESOLUTION, COMM.SETUP, LANGUAGE and FACTORY DEFAULT

SAVE & EXIT – Exits the menu after saving the parameters. EXIT – Exits the menu without saving the menu.

Further information

The manual is available from the eneo web site at www.eneo-security.com or from the CD supplied with this product.

+ 25 hidden pages

Eneo HDB-1080Z03IR D User Manual [en, de, fr]

Specifications and Main Features

Frequently Asked Questions

User Manual