Emerson Liebert GXT4 User Manual

Liebert® GXT4™ UPS 120V/208V 500VA-3000VA

User Manual

TABLE OF CONTENTS

IMPORTANT SAFETY PRECAUTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1

SAVE THESE INSTRUCTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1

GLOSSARY OF SYMBOLS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

1.0 PRODUCT DESCRIPTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4

1.1 Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

1.2 Available Models . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

1.3 Appearance and Components . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

1.3.1 Front Panel and Controls. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

1.3.2 Rear Panel Features. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

1.4 Major Components . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

1.5 Operating Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

1.5.1 Mains Mode. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

1.5.2 Manual Bypass Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

1.5.3 Battery Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

1.5.4 Battery Recharge Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

1.5.5 Frequency Converter Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

1.5.6 Active ECO Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

2.0 INSTALLATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

2.1 Unpacking and Inspection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

2.2 What’s Included . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

2.3 Preparation for Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

2.3.1 Installation Environment. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

2.4 Mechanical Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

2.4.1 Tower Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

2.4.2 Rack Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

2.5 Cable Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

2.5.1 Connecting to AC Mains and Loads . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

2.5.2 Connecting Battery Cables . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

2.6 Connecting Communication Cables. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

2.6.1 Connecting USB Communication Cables . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

2.6.2 Installing the Optional Liebert IntelliSlot

Card and Communication Cables . . . . . . . . . . . 15

3.0 OPERATION AND DISPLAY PANEL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16

3.1 LED Indicators . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

3.2 Control Buttons . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

3.3 LCD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

3.4 Menu Structure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

3.4.1 Startup Screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

3.4.2 Default Screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20

3.4.3 Main Menu Screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20

3.4.4 Prompt List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30

3.4.5 Warning List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30

3.4.6 Fault List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31

4.0 OPERATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .32

4.1 Startup Checklist for the Liebert GXT4 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32

4.2 Starting the UPS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32

4.3 Manual Battery Test . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32

4.4 Manual Bypass . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32

4.5 Shut Down the Liebert GXT4 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33

4.6 Disconnecting Input Power from the Liebert GXT4. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33

5.0 COMMUNICATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34

5.1 Liebert IntelliSlot Communication Cards. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34

5.1.1 Liebert MultiLink . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34

5.2 USB Port Communication . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34

5.2.1 Configuration Program . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35

5.3 RS-232 Port. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36

5.4 Terminal Block Communication . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36

5.4.1 Any Mode Shutdown . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36

5.4.2 Battery Mode Shutdown . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37

5.4.3 On Battery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37

5.4.4 Low Battery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37

6.0 MAINTENANCE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .38

6.1 Replacing the Internal Battery Pack. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38

6.1.1 Battery Replacement Procedures . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39

6.2 Battery Charging . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40

6.3 Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40

6.4 Checking UPS Status . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40

6.5 Checking UPS Functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40

7.0 TROUBLESHOOTING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .41

7.1 UPS Symptoms. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41

7.1.1 Indicator and LCD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41

7.1.2 Audible Alarm. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42

7.2 Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42

8.0 BATTERY CABINET . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .43

9.0 S

9.1 Product Warranty Registration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49

9.2 Technical Support. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49

PECIFICATIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44

FIGURES

Figure 1 Liebert GXT4 rack/tower models—front view . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

Figure 2 Rear panel components—Liebert GXT4 120V rack/tower, 500, 700, 1000VA model . . . . . . . . . . . 5

Figure 3 Rear panel components—Liebert GXT4 120V rack/tower, 1500VA model . . . . . . . . . . . . . . . . . . . 6

Figure 4 Rear panel components—Liebert GXT4 120V rack/tower, 2000VA model . . . . . . . . . . . . . . . . . . . 6

Figure 5 Rear panel components—Liebert GXT4 120V rack/tower, 3000VA model . . . . . . . . . . . . . . . . . . . 7

Figure 6 Rear panel components—Liebert GXT4 208V rack/tower, 3000VA model . . . . . . . . . . . . . . . . . . . 7

Figure 7 Operating principle diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

Figure 8 Support bases . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

Figure 9 Remove the front plastic bezel cover . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

Figure 10 Rotate the operation and display panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

Figure 11 Tower installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

Figure 12 Cable strain relief . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

Figure 13 Battery cable attachment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

Figure 14 Operation and display panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

Figure 15 Menu structure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

Figure 16 Startup screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

Figure 17 Startup screens . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

Figure 18 Starting and Start Successful screens . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

Figure 19 Default screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20

Figure 20 Main Menu screen. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20

Figure 21 Status screens . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21

Figure 22 CONFIGURATION screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21

Figure 23 UPS screens. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22

Figure 24 Battery screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22

Figure 25 ECO Mode screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

Figure 26 Outlet1 screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

Figure 27 Outlet Control screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24

Figure 28 Outlet Setting screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24

Figure 29 Outlet2 setting screen. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25

Figure 30 LCD screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25

Figure 31 Language screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25

Figure 32 Color screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26

Figure 33 Factory Default screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26

Figure 34 Control screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26

Figure 35 Turn UPS On or Off screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27

Figure 36 Alarm Control screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27

Figure 37 Batt Test screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27

Figure 38 Log screens . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28

Figure 39 Clear Log screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28

Figure 40 About screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28

Figure 41 Network screens . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29

Figure 42 Terminal Block Communication pin layout. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36

Figure 43 Removing the front bezel cover and battery door . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39

Figure 44 Disconnecting the battery plug and battery receptacle (front view) . . . . . . . . . . . . . . . . . . . . . . . 39

Figure 45 Pull out the battery. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39

Figure 46 Battery cabinet . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43

iii

TABLES

Table 1 UPS models, power ratings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

Table 2 Input circuit breaker specification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

Table 3 LED indicators . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

Table 4 Control buttons . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

Table 5 System prompts and meanings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30

Table 6 Warning list. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30

Table 7 Fault list . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31

Table 8 Output voltage option . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35

Table 9 Replacement internal battery pack model number. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38

Table 10 Description of the displayed fault . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41

Table 11 Audible alarm description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42

Table 12 Troubleshooting table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42

Table 13 Specifications of GXT4-500RT120 - GXT4-700RT120 and GXT4-1000RT120 models . . . . . . . . . 44

Table 14 Specifications of GXT4-1500RT120 - GXT4-3000RT120 and GXT4-3000RT208 models . . . . . . . 45

Table 15 Operating temperature parameters. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46

Table 16 Battery cabinet specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46

Table 17 Battery run times . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47

IMPORTANT SAFETY PRECAUTIONS

WARNING

Observe all cautions and warnings in this manual. Failure to do so may result in serious injury or death.

Refer all UPS and battery service to properly trained and qualified service personnel. Do not attempt to service this product yourself.

Opening or removing the cover may expose you to lethal voltages within this unit even when it is apparently not operating and the input wiring is disconnected from the electrical source.

Never work alone.

SAVE THESE INSTRUCTIONS

This manual contains important safety instructions that must be followed during the installation and maintenance of the UPS and batteries. Read this manual thoroughly before attempting to install or operate this UPS.

UPS Safety Notes

This UPS contains no user-serviceable parts except the internal battery pack. The Off/Bypass push button does not electrically isolate internal parts. Under no circumstances attempt to gain internal access other than to replace the batteries due to risk of electric shock or burn. Do not continue to use the UPS if the front panel indications are not in accordance with these operating instructions or if the UPS performance alters in use. Refer all faults to your local dealer, Emerson Network Power representative or Emerson Network Power Channel Support.

This UPS has an internal battery, and the output receptacles of the UPS may carry live voltage even if the UPS is not connected to utility input power.

Before moving or rewiring this UPS, disconnect utility input power and the battery and make sure that the UPS is completely shut down. Otherwise, the output terminal may carry live voltage, presenting an electric shock hazard.

To ensure human safety and normal UPS operation, the UPS must be properly grounded before use. When the UPS is connected to an IT power distribution system, a short-circuit protection device must

be installed on the neutral line. Install and use the Liebert GXT4 in the following environments:

• Temperature: 32°F - 104°F (0°C - 40°C), relative humidity: 0% ~ 95% non-condensing

• Out of direct sunlight

• Away from heat sources

• Stable surface, not subject to vibrations or shocks

• Away from dust and other particulates

• Away from corrosive substances, salts and flammable gases

Keep the air inlet and outlet of this UPS unobstructed. Poor ventilation will increase the internal temperature of the UPS and can adversely affect the UPS and its batteries.

Keep liquid and foreign objects away from the UPS. In case of fire, use a dry chemical fire extinguisher to put out the fire. Using a fluid fire extinguisher

may cause electric shock. This UPS is not intended for use with life support and other designated critical devices. Maximum

load must not exceed that shown on the UPS rating label. This UPS is designed for data processing equipment. If uncertain, consult your local dealer or Emerson representative.

This UPS is not for use in a computer room as defined in the standard for the Protection of Electronic Computer/Data Processing Equipment, ANSI/NFPA 75.

The Liebert GXT4-3000RT120 Electrical Code, ANSI/NFPA 70. To reduce the risk of fire, connect only to a circuit provided with 30A maximum branch overcurrent protection.

™

was tested under 30A branch circuit in accordance with the National

1Liebert

GXT4

™

The Liebert GXT4-3000RT208 was tested under 20A branch circuit in accordance with the National

Electrical Code, ANSI/NFPA 70. To reduce the risk of fire, connect only to a circuit provided with 20A maximum branch overcurrent protection.

Battery Safety

CAUTION

Do not dispose of batteries in a fire. The batteries may explode. Do not open or mutilate the batteries. Released electrolyte is toxic and is harmful to skin and

eyes. Dispose of used batteries according to the instructions.

CAUTION

A battery can present a risk of electrical shock and high short circuit current. The following precautions should be observed when working on batteries:

• Remove watches, rings and other metal objects.

• Use tools with insulated handles.

• Wear rubber gloves and boots.

• Do not lay tools or metal parts on top of batteries.

• Disconnect charging source prior to connecting or disconnecting battery terminals.

• Determine if the battery is inadvertently grounded. If it is inadvertently grounded, remove the source of the ground. Contact with any part of a grounded battery can result in electrical shock. The likelihood of such shock will be reduced if grounds are removed during installation and maintenance (applicable to a UPS and a remote battery supply not having a grounded supply circuit).

ELECTROMAGNETIC COMPATIBILITY—The Liebert GXT4 complies with the limits for a CLASS A DIGITAL DEVICE, PURSUANT TO Part 15 of FCC rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference and (2) this device must accept any interference received, including interference that may cause undesired operation. Operating this device in a residential area is likely to cause harmful interference that users must correct at their own expense.

The Liebert GXT4 series complies with the requirements of EMC Directive 2004/108/EC and the published technical standards. Continued compliance requires installation in accordance with these instructions and use of accessories approved by Emerson.

Information for the Protection of the Environment

UPS Servicing: UPS makes use of components dangerous for the environment (electronic cards, electronic components). The components removed must be taken to specialized collection and disposal centers.

Liebert® GXT4

™

GLOSSARY OF SYMBOLS

PbH2SO4

Risk of electrical shock

Indicates caution followed by important instructions

AC input

AC output

Requests the user to consult the manual

Indicates the unit contains a valve-regulated lead acid battery

Recycle

DC voltage

Equipment grounding conductor

Bonded to ground

AC voltage

WEEE

3Liebert

GXT4

™

1.0 PRODUCT DESCRIPTION

The Liebert GXT4 is a compact, online uninterruptible power system (UPS) that continuously conditions and regulates its output voltage. The Liebert GXT4 is designed to supply microcomputers and other sensitive equipment with clean sine wave input power.

Upon generation, AC power is clean and stable. However, during transmission and distribution it is subject to voltage sags, spikes and complete failure that may interrupt computer operations, cause data loss and damage equipment.

The Liebert GXT4 protects equipment from these disturbances. The Liebert GXT4 continuously charges its batteries from utility power, enabling it to supply power to connected loads, even when utility power fails.

This sections describes the UPS, its features, models, appearance and components, operating principles and operating mode.

1.1 Features

• Intelligent battery management to extend the battery life

• LCD for user-friendly operation and local monitoring and configuration of operational parameters

• Controllable outlet groups

• Flexible network management with Liebert MultiLink

• Fan fault self-inspection and automated diagnostic function

• Intelligent fan operation, automatically changing rotation speed depending on system requirements, to decrease power consumption and noise

• Input circuit breaker to ease recovery from overloads

• Safety approval from UL and cUL

• Communication options: USB port, Liebert IntelliSlot

• Dry contacts for remote monitoring

• Input power factor greater than0.99

• Output voltage selection function

Product Description

™

software

port and terminal block communication

1.2 Available Models

Eight UPS models are available.

Table 1 UPS models, power ratings

Model Nominal Power Rating

GXT4-500RT120 500VA/450W

GXT4-700RT120 700VA/630W

GXT4-1000RT120 1000VA/900W

GXT4-1500RT120 1500VA/1350W

GXT4-2000RT120 2000VA/1800W

GXT4-3000RT120 3000VA/2700W

GXT4-3000RT208 3000VA/2700W

Liebert® GXT4

™

1.3 Appearance and Components

Operation and

Display Panel

Ventilation Slots

Liebert IntelliSlot Port

External Battery Connector

Programmable Output Receptacles #1

Input Circuit Breaker

Cooling Fan

RS232 Port

Terminal Block Communication

Input Power Plug and Cable

USB Port

General Output Receptacle

Programmable Output Receptacle

Strain Relief Attachment

1.3.1 Front Panel and Controls

The Liebert GXT4 rack/tower models in various power ratings have the same general appearance, controls and features (see Figure 1). The various rack/tower and minitower models differ largely in the type of receptacles each has.

Figure 1 Liebert GXT4 rack/tower models—front view

1.3.2 Rear Panel Features

The rear panel of the Liebert GXT4 has these features:

• Liebert IntelliSlot

•USB port

• Input Circuit Breaker

•Input Receptacle

• General Output Receptacles

• Programmable Output Receptacles

• Cable Strain Relief Attachment Hole

• External Battery Connector

• Cooling Fan

• RS-232 port

• Terminal Block Communication

• Output Circuit Breakers (only on 3000VA models)

Port

Product Description

Figure 2 Rear panel components—Liebert GXT4 120V rack/tower, 500, 700, 1000VA model

5Liebert

GXT4

™

Figure 3 Rear panel components—Liebert GXT4 120V rack/tower, 1500VA model

Liebert IntelliSlot Port

Input Circuit Breaker

Input Power Plug and Cable

External Battery Connector

Cooling Fan

RS232 Port

Terminal Block Communication

Programmable Output Receptacle #1

Programmable Output Receptacle #2

General Output Receptacle

Strain Relief Attachment

USB Port

Liebert IntelliSlot Port

Input Circuit Breaker

Input Power Plug and Cable

External Battery Connector

Cooling Fan

RS232 Port

Terminal Block Communication

Programmable Output Receptacle #1

Programmable Output Receptacle #2

General Output Receptacle

Strain Relief Attachment

USB Port

Figure 4 Rear panel components—Liebert GXT4 120V rack/tower, 2000VA model

Product Description

Liebert® GXT4

™

Figure 5 Rear panel components—Liebert GXT4 120V rack/tower, 3000VA model

Liebert IntelliSlot Port

USB Port

Input Circuit Breaker

Terminal Block Communication

RS232 Port

Cooling Fan

External Battery Connector

Strain Relief Attachment

Programmable Output Receptacle #1

Input Power Plug and Cable

General Output Receptacle

Programmable Output Receptacle #2

Output Circuit Breaker

Output

Input Power Plug and Cable, L6-20P

External

Battery

Connector

USB Port

Cooling Fan

Input Circuit Breaker

Programmable Output Receptacle 1 L6-15R

Output Circuit Breakers

Liebert IntelliSlot Port

Terminal Block Communication

Non-Programmable Output Receptacle 2 L6-20R

Programmable Output Receptacle 2 L6-15R

Product Description

Figure 6 Rear panel components—Liebert GXT4 208V rack/tower, 3000VA model

7Liebert

GXT4

™

1.4 Major Components

TVSS

EMI/RFI

Input Filter

Inverter

DC-DC

Converter

Battery

Charger

Battery

Dynamic

Bypas s

N/L2*

Programmable

Outlet

Group 1

General

Outlet Group

Programmable

Outlet

Group 2

General

Outlet

(3000 VA Only)

N/L2*

EMI/RFI

Output

Filter

* NOT E: ONLY the GXT 4-3000 RT208 m odel (208V) requires L 2 (L6- 20P).

All other model s c overed in this manual are 120 V L-N wired

Rectifier /

PFC

The operating principle of the UPS is illustrated in Figure 7.

Figure 7 Operating principle diagram

Product Description

The UPS is composed of utility input, TVSS and EMI/RFI filters, rectifier/PFC, inverter, battery charger, DC-to-DC converter, battery, dynamic bypass and UPS output.

Transient Voltage Surge Suppression (TVSS) and EMI/RFI Filters

The Liebert GXT4 has surge protection and filters that protect the connected load from power surges, electromagnetic interference (EMI) and radio frequency interference (RFI). These features can minimize any surges or interference present in the utility power. The filters also prevent surges or interference generated by the UPS from adversely affecting devices connected on the same branch as the UPS.

Rectifier/Power Factor Correction (PFC) Circuit

In normal operation, the Liebert GXT4’s rectifier/power factor correction (PFC) circuit converts utility power to regulated DC power for use by the inverter while ensuring that the wave shape of the input current used by the UPS is near ideal. Extracting this sinewave input current achieves two objectives:

• Efficient power use by the UPS

• Reduced reflected harmonics

This results in cleaner power being available to other devices in the building not being protected by the Liebert GXT4.

Inverter

In normal operation, the Liebert GXT4’s inverter utilizes the DC output of the PFC to produce precise, regulated sine wave AC power. When utility power fails, the inverter receives DC power from the DC-to-DC Converter. In either operation mode, the UPS inverter is online, continuously generating clean, precise, regulated AC output power.

Battery Charger

The battery charger utilizes energy from the utility power and precisely regulates it to continuously float charge the batteries. The batteries are being charged whenever the Liebert GXT4 is plugged in, even when the UPS is not turned On.

Liebert® GXT4

™

DC-to-DC Converter

The DC-to-DC converter raises the DC voltage from the battery to the optimum operating voltage for the inverter. This allows the inverter to operate continuously at its optimum efficiency and voltage, thus increasing reliability.

Battery

The Liebert GXT4 uses valve-regulated, nonspillable, lead acid batteries. To maintain battery design life, operate the Liebert GXT4 in an ambient temperature of 32°F to 77°F (0°C to 25°C).

Optional external battery cabinets are available to extend battery run times.

Dynamic Bypass

The Liebert GXT4 provides an alternate path for utility power to the connected loads in the unlikely event of a UPS malfunction. Should the Liebert GXT4 have an overload, overtemperature or UPS failure condition, the UPS automatically transfers the connected loads to bypass.

NOTE

The bypass power path does not protect the connected loads from disturbances on the utility.

1.5 Operating Mode

The UPS operation modes include the following: Mains (AC) Mode, Bypass Mode, Battery Mode, Battery Recharge Mode, Active ECO Mode and Frequency Converter Mode.

Refer to 9.0 - Specifications for details about the operating mode indicators and control buttons.

Product Description

1.5.1 Mains Mode

During Mains Mode, the mains provides input power to the Liebert GXT4. The filters, PFC circuit and inverter process this power to provide high-quality sine wave power to connected loads. The UPS maintains the batteries in a fully charged state.

1.5.2 Manual Bypass Mode

Manual Bypass Mode occurs when the unit is manually placed in internal bypass by navigating the LCD display menu to select 3 Control > 1 Turn On & Off > Turn UPS Bypass. Bypass operation is indicated by an audible alarm and illuminated amber bypass indicator. (If other indicators are illuminated, refer to 7.0 - Troubleshooting). During Bypass Mode, mains power bypasses the inverter and provides energy to the connected load.

NOTICE

Risk of loss of power to the connected load. Can cause equipment damage. Turning Off the UPS in Bypass Mode will result in loss of output power to the connected load.

9Liebert

GXT4

™

1.5.3 Battery Mode

The Liebert GXT4 enters Battery Mode when mains power fails or is outside acceptable limits. The battery system supplies power through the DC-to-DC converter to the inverter to generate clean AC power for the connected loads.

When the Liebert GXT4 enters Battery Mode, the UPS sounds a half-second beep at 10-second intervals. When approximately 2 minutes of run time remains, the beeps sound every 5 seconds to warn that the battery is getting low (this Low Battery Warning is user-configurable).

In Battery Mode, the battery indicator will illuminate and the LCD will show the prompt utility power not available.

Press either the Up or Down button once, then press the Enter button to clear the prompt and silence the audible alarm. Once the alarm prompt has been acknowledged, the screen showing the estimated battery run time and battery capacity will be visible. Refer to 7.0 - Troubleshooting.

For approximate battery run times, refer to Table 17.

NOTICE

Risk of loss of power to the connected load. Can cause equipment damage. Turning Off the Liebert GXT4 when it is in Battery Mode will result in loss of output power to

the connected load. If the UPS is turned Off manually, it must be manually restarted after mains power returns. If the UPS is turned Off by a communication signal or because the batteries are depleted, it

will operate as set in the configuration program for Auto-Restart (Refer to 5.2.1 - Configuration Program).

Product Description

1.5.4 Battery Recharge Mode

Once mains power is applied to the Liebert GXT4, the Battery Charger begins charging the batteries.

1.5.5 Frequency Converter Mode

All models of the Liebert GXT4 are capable of frequency conversion. Frequency Conversion Mode can be selected using the configuration program. Allowable frequency operating modes include:

• Auto Sensing - 50Hz or 60Hz – Bypass Enabled

• Auto Sensing - 50Hz or 60Hz – Bypass Disabled

• Frequency Converter - 50Hz – Bypass Disabled

• Frequency Converter - 60Hz – Bypass Disabled

NOTE

The default for all models of the Liebert GXT4 is “Auto Sensing - 50Hz or 60Hz – Bypass Enabled.”

CAUTION

Risk of electric shock. Can cause injury or death. Never touch the AC input receptacle while the UPS is operating. Voltage may still be present

even when the AC input indicator is Off.

1.5.6 Active ECO Mode

All Liebert GXT4 models can operate in Active ECO Mode. In this mode, the connected equipment is powered through the bypass path to increase efficiency, reducing the electrical costs.

Active ECO mode keeps the rectifier and inverter operating, allowing the inverter to remain synchronized to bypass. This synchronization allows the transfer of the connected equipment to UPS inverter power almost seamlessly if bypass power falls outside the user-set limits. Once bypass power returns within the acceptable parameters, the UPS will return to Active ECO Mode operation.

The default setting is Active ECO Mode Off.

Liebert® GXT4

™

2.0 INSTALLATION

2.1 Unpacking and Inspection

Unpack the UPS and conduct the following checks:

• Inspect the UPS for shipping damage. If any shipping damage is found, report it to the carrier and your local dealer or your Emerson representative immediately.

• Check the accessories included in packaging list. If there is any discrepancy, contact your local dealer or your Emerson representative immediately.

2.2 What’s Included

• Terminal Block Communication Terminals

• Compact Disk with:

• Liebert MultiLink

• Configuration Program

• User Manual

• USB Cable—one, 1.2m (3.9 ft.) long

• RS-232 Cable—one, 2m (6-1/2 ft) long

• Cable Strain Relief—two pieces

• Rack mounting hardware, including screws, handles and mounting rail kit (not included with model numbers ending with an “E”)

• Plastic tower stand sets—two (four pieces)

• Warnings, Safety Instructions booklet and WEEE recycling sheet (ISO 14001 compliance))

Shutdown Software

Installation

NOTE

The GXT4 External Battery Cabinet shipping package includes one battery cabinet, two spacers for tower configuration and one DC power cable and rack mounting hardware, including screws, handles and mounting rail kit (not included with model numbers ending with an “E”).

2.3 Preparation for Installation

2.3.1 Installation Environment

• Install the UPS indoors in a controlled environment, where it cannot be accidentally turned Off. The installation environment should meet the specifications listed in 9.0 - Specifications).

• Place it in an area of unrestricted airflow around the unit, away from water, flammable liquids, gases, corrosives, and conductive contaminants. Avoid direct sunlight.

NOTE

Operating the Liebert GXT4 in temperatures above 77°F (25°C) reduces battery life.

Installation Clearances

Maintain at least 4 inches (100mm) clearance in the front and rear of the Liebert GXT4. Do not obstruct the air inlets on the front panel and rear panel of the UPS; blocking the air inlets reduces ventilation and heat dissipation, shortening the service life of the Liebert GXT4.

11 Liebert® GXT4

™

2.4 Mechanical Installation

Support Bases

Spacers

Connectors

Front Bezel Cover

The Liebert GXT4 may be installed as a tower or in a rack, depending on space and use considerations. The Liebert GXT4 may be used alone, as a single UPS, or with up to four battery cabinets.

NOTE

When installing the UPS or making input and output connections, comply with all relevant safety codes and standards

2.4.1 Tower Installation

To install the Liebert GXT4 as a tower:

1. Take out support bases from the accessories (see Figure 8).

Figure 8 Support bases

Installation

2. If optional Liebert external battery cabinets will be connected to the Liebert GXT4, take out the spacers shipped with the battery cabinet.

3. Connect the spacers and the support bases as shown in Figure 8. Each Liebert GXT4 needs two assembled support bases, one in the front and one in the rear.

4. Adjust the direction of the operation and display panel and logo on the Liebert GXT4. a. Remove the front plastic bezel cover as shown in Figure 9.

Figure 9 Remove the front plastic bezel cover

b. Pull the operation and display panel gently, rotate it 90 degrees clockwise and snap it back

into position, as shown in Figure 10.

Liebert® GXT4

™

Figure 10 Rotate the operation and display panel

Rotate Operation and

Display Panel

90 degrees clockwise

Operation and

Display Panel

Rotated for

Tower Operation

Support

Bases

Support Bases

Liebert GXT4 UPS

Liebert GXT4 UPS and

External Battery Cabinet

c. Pull the logo on the front plastic bezel cover gently, rotate it 90 degrees clockwise and snap it

back into position. The rotated front plastic bezel cover is shown in Figure 11.

d. Replace the front plastic bezel cover on the Liebert GXT4. At this point, the UPS operation

and display panel and logo have been rotated 90 degrees clockwise, which provides upright viewing for users.

5. Place the Liebert GXT4 and any battery cabinets on the support bases. Each Liebert GXT4 needs two support assemblies, as shown in Figure 11.

Figure 11 Tower installation

Installation

2.4.2 Rack Installation

The Liebert GXT4 UPS and external battery cabinets (EBC), when installed in a rack enclosure, must be supported by a shelf or rack-mount rails. The Liebert GXT4 UPS and EBC units ship with all required hardware to allow rack-mount installation (not included with model numbers that end in “E”). Because different rack-mount options install differently, refer to the installation instructions provided with the rack mount kit being used.

13 Liebert® GXT4

™

2.5 Cable Connection

Hold the cable

Insert into the provided hole to secure the line buckle

The Liebert GXT4 rear panel has an input cable and plug, output receptacles and output cable(s) (Output cables are on GXT4-3000 models only). Refer to 1.3.2 - Rear Panel Features for details. The battery cables are supplied with the battery cabinet.

2.5.1 Connecting to AC Mains and Loads

NOTE

Ensure that all the loads are turned Off.

Prepare an input power supply that is properly protected by a circuit breaker in accordance with national and local electrical codes. The wall receptacle must be grounded.

Emerson recommends installing an upstream circuit breaker of the same series as the Liebert GXT4’s input circuit breaker.

The specification of input circuit breaker on the rear panel of UPS is given in Table 2..

Table 2 Input circuit breaker specification

Model

GXT4-500RT120 8A

GXT4-700RT120 10A

GXT4-1000RT120 10A

GXT4-1500RT120 15A

GXT4-2000RT120 20A

GXT4-3000RT120 30A

GXT4-3000RT208 20A

Rated Circuit

Breaker

Installation

Liebert GXT4 models 700-1500VA and 2000VA have three groups of outlets as shown in Figure 2. One group is always On; the other two groups may be controlled with either programmed responses or over an SNMP network. The 3000VA GXT4 UPS has four groups of outlets: two groups are not controlled (always On), and two groups may be controlled with either programmed responses or over an SNMP network.

Verify that the equipment is plugged into the appropriate outlets if any outlets will be controlled with these features.

1. Plug equipment into the appropriate output receptacles on the rear of the Liebert GXT4.

NOTE

1. Do not overload any output receptacle.

2. Output cable length should not exceed 10m (32.8 ft).

2. Plug the input receptacle of the Liebert GXT4 into the input power connection.

3. Install the two cable strain relief fixtures to secure either the input or output cables to prevent accidental disconnection.

a. Insert one end into the provided holes on the rear of the unit. b. Place the power cord(s) inside the loop. c. Tighten the loop around the cables.

Figure 12 Cable strain relief

Liebert® GXT4

™

2.5.2 Connecting Battery Cables

Liebert GXT4

External Battery Cabinet

Battery Cable

1. Switch Off the input breaker of the battery cabinet.

2. Take out the battery cable included with the battery cabinet.

3. Connect one end of the battery cable to the external battery connector on the rear panel of the UPS, and connect the other end to any battery port on the rear panel of the battery cabinet.

4. Switch On the battery breaker on the rear of the external battery cabinet.

5. Use the Configuration Program included with the UPS to specify the number of external battery cabinets connected to the Liebert GXT4. See Table 17 for approximate battery run times.

Figure 13 Battery cable attachment

Installation

2.6 Connecting Communication Cables

Communication cable connection includes: USB and cables for option cards.

2.6.1 Connecting USB Communication Cables

1. Take the USB communication cables out of the accessories bag.

2. Insert one end of the USB communication cable to the USB port on the rear panel of the Liebert GXT4 (see Figures 2 and 1.4).

3. Insert the other end of the USB communication cable to the USB port of the computer.

2.6.2 Installing the Optional Liebert IntelliSlot® Card and Communication Cables

1. Remove the protective cover of the Liebert IntelliSlot port on the Liebert GXT4 and set it aside.

2. Insert the Liebert IntelliSlot card into the Liebert IntelliSlot port and secure it with screws.

3. To connect any cable associated with a Liebert IntelliSlot card, refer to the user manual provided with the card.

To configure and use the Liebert IntelliSlot communication card, refer to the card’s user manual. Manuals for the various Liebert IntelliSlot cards are available at Liebert’s Web site:

www.liebert.com

15 Liebert® GXT4

™

3.0 OPERATION AND DISPLAY PANEL

ESC Button

UP Button

Programmable Outlet 1 Indicator

Bypass Indicator

DOWN Button

ECO Mode Indicator

LCD Panel

Programmable Outlet 2 Indicator

Battery Indicator

Fault Indicator

Inverter Indicator

ENTER Button

This chapter describes the Liebert GXT4 controls, particularly the operation and display panel on the front of the Liebert GXT4. The panel has four control buttons, seven LED indicators and a liquid crystal display (LCD), as shown in Figure 14.

Figure 14 Operation and display panel

Operation and Display Panel

3.1 LED Indicators

The seven LED indicators on the front of the operation and display panel are:

• Inverter

•Battery

•Bypass

• Programmable Outlet1

• Programmable Outlet2

• ECO Mode

•Fault

Figure 14 shows the indicators’ locations; their descriptions and functions are shown in Table 3.

Table 3 LED indicators

LED Indicators

Inverter Green On when the inverter is supplying power

Bypass Amber

Battery Amber On when the load is supplied by the battery

Fault Red On when an error has occurred within the UPS

Programmable Outlet1 Green On when programmable Outlet1 is On

Programmable Outlet2 Green On when programmable Outlet2 is On

ECO Mode Green On when the UPS is in ECO Mode

LED Color

Description

On when the load is supplied by the mains through automatic/manual bypass

Liebert® GXT4

™

3.2 Control Buttons

The four control buttons on the front of the operation and display panel are:

•ESC

•Up

•Down

•Enter

Figure 14 shows the buttons’ locations; their descriptions and functions are shown in Table 4.

Table 4 Control buttons

Control Buttons Description

ESC Button

Up Button

Down Button

Enter Button Pressing this button can enter the next level menu or confirm the parameter setting value.

3.3 LCD

The LCD panel shows the UPS status and enables changes to the UPS settings by assisting in navigating through the Liebert GXT4’s menu (see 3.4 - Menu Structure).

Operation and Display Panel

Pressing this button returns to the previous menu or aborts any change in the input data field before confirming.

Pressing this button can move the cursor up or increase the value displayed in the input data field. When a menu is displayed on several screens, pressing the button can scroll up.

Pressing this button can move the cursor down or decrease the value displayed in the input data field. When a menu is displayed on several screens, pressing the button can scroll down.

17 Liebert® GXT4

™

3.4 Menu Structure

Audible Alarm

Control

Status

Configuration

Log

About

Alarm Control

Batt Test

1. Audible Alarm On

2. Audible Alarm Off

1. Start

2. Cancel

3. Batt Test Result

PN/SN/Firmware Version

Turn UPS On Turn UPS Off

Address: MAC

Address: IPV4

Address: IPV6STATIC

Address: IPV6AU TO

Address: IPV6LINK

Startup on Bypas s

Enable Auto Restart

Enable Auto Shutdown

Frequency Selection

Output Lev el Selec tion

Battery Cabinets

Low Battery Time Warning

Batt Test Interval

Batt Replace Time

BATT

UPS

Turn UPS

On/Off

View Log

Clear Log

Start

Windows

System

Status

Main

Network

Time Since Startup

Battery

Input

Load

Output

Sett ings as Outlet1 ( only Outl et2 ) Turn On Delay Turn Off W hen UP S On Battery and On Overload Turn Off W hen UP S On Battery for Some Time Turn On W hen P ower Returns for Some Time Turn Off When R untime Les s Than Some Time Turn Off W hen Bat t Capacity Less Than Some Time

LCD

Language

Color

Factory Default

Control

Turn On Turn Off

Reboot

Outlet 2

Outlet 1

Setting

ECO Mode

Frequency Tolerance

Requalification Time

Enable /Disable

Voltage Tolerance

1 English 2 French

The menu structure of the LCD is shown in Figure 15.

Figure 15 Menu structure

Operation and Display Panel

Liebert® GXT4

™

3.4.1 Startup Screen

EMERSON

Network Power

O/P: 0V HZ 0.0A I/P : 120 V 60HZ 0.0A BATT: 100 % 320 MINS LOAD: 0%

TURN ON UPS

YES NO

O/P: 0V 0HZ 0.0A I/P : 120V 60HZ 0.0A BATT: 100% 320MINS LOAD: 0%

AC NOT AVAILABLE START ON BATTERY?

YES NO

Input Power is Available

Input Power is not Available

O/P: 0V 0HZ 0.0A I/P : 120V 60HZ 0.0A BATT: 100% 320MINS LOAD: 0%

UPS STARTING

O/P: 120V 60H Z 4.6A I/P : 120V 60HZ 5.0A BATT: 100% 15MINS LOAD: 40%

START SUCCESSFUL

When the Liebert GXT4 is starting up, it initiates a self-test and displays the screen shown in Figure 16 for about 10 seconds.

Figure 16 Startup screen

After about 10 seconds, the LCD shows one of the On screens in Figure 17; the screen shown depends on whether input power is available.

Figure 17 Startup screens

Operation and Display Panel

To turn On the UPS, press either the Up or Down button to select YES and press the Enter button. The UPS will start up, the LCD will display UPS STARTING and then START SUCCESSFUL after the UPS is turned On, as shown in Figure 18.

Figure 18 Starting and Start Successful screens

19 Liebert® GXT4

™

3.4.2 Default Screen

O/P: 120V 60HZ 11.7A I /P: 120V 60HZ 13.1A BATT: 100% 3MINS LOAD: 100%

GXT4-UPS 3KVA

Values shown will vary according to installation and configuration.

1 STATUS

2 CONFIGURATION 3 CONTROL 4LOG 5 ABOUT 6NETWORK

Press any button in the START SUCCESSFUL screen to enter the default interface, shown in Figure 19.

Figure 19 Default screen

In the default screen, the LCD shows the UPS model, output parameters, input parameters, battery capacity with run time estimate and load percentage. The UPS operation mode (online /inverter, ECO, Battery or Bypass) will be indicated by the LED indicators.

If no control button (ESC, Up, Down, Enter) is pressed for 2 minutes, the LCD will enter the screen saver mode (backlight turns off). It will remain off until a control button is pressed.

Operation and Display Panel

3.4.3 Main Menu Screen

Press the Enter button in the default screen to enter the MAIN MENU screen, as shown in Figure 20.

Figure 20 Main Menu screen

To select a submenu, press the Up or Down button to move the cursor to the required item, then press the Enter button to enter its submenu or set its parameter.

Liebert® GXT4

™

STATUS Screen

VOLTAGE : 120V FREQUENCY : 60HZ CURRENT : 17.6A POW ER : 2112 KW H

OUTPUT

CAP : 90% WATT : 1620W VA : 1800VA

LOAD

VOLT : 120V FREQ : 60 HZ CURR : 18.6A POWER : 97KWH

INPUT

CAPACITY : 90% RUNTIME : 100MINS VOLTAGE : 80V

BATTERY

05D 15H 30M

TIME SINCE STARTUP

1. UPS

2. BATTERY

3. ECO MODE

4. OUTLET 1

5. OUTLET2

6. LCD

7. FACTORY DEFAULT

In the MAIN MENU screen, select STATUS to enter the Status Screen, displaying OUTPUT, LOAD, INPUT, BATTERY and TIME SINCE STARTUP, as shown in Figure 21.

Figure 21 Status screens

Operation and Display Panel

CONFIGURATION Screen

Select MAIN MENU > CONFIGURATION to enter the Configuration menu. This menu has seven submenus, as shown in Figure 22.

Figure 22 CONFIGURATION screen

In the CONFIGURATION screen, press the Up or Down button to move the cursor to the required item, then press the Enter button to enter a submenu or set its parameters.

21 Liebert® GXT4

™

UPS Screen

OFF

AUDIBLE ALARM

STARTUP ON BYPASS

GUARANTEE SHUTDOWN

YES

ENABLE AUTO RESTART

AUTO - BYPASS ENABLE

FREQUENCY SELECTION

230

VOLTAGE SELECTION

0 CABINETS

EXT BATT CABINET

2MINS

LOW BATTERY TIME

8WEEKS

BATT TEST INTERVAL

2014 Y 1 M 1 D

BATT REPLACE TIME

Select MAIN MENU > CONFIGURATION > UPS to enter the UPS screen. This menu has six screens, as shown in Figure 23.

Figure 23 UPS screens

Operation and Display Panel

Press the Up or Down button to move the cursor to the required item, and press the Enter button to confirm the settings.

Battery Screen

Select MAIN MENU > CONFIGURATION > BATTERY to enter the BATTERY screen. This menu has four screens, as shown in Figure 24.

Figure 24 Battery screen

Liebert® GXT4

Press the Up or Down button to increase or decrease the value of the settings, and press the Enter button to confirm it.

™

ECO Mode Screens

ECO MODE

3 Hz

FREQUENCY TOLERANCE

10%

VOLTAGE TOLERANCE

5 MINS

REQUALIFICATION TIME

OUTLET1

1 OUTLET CONTROL

2 OUTLET SETTING

Select MAIN MENU > CONFIGURATION > ECO MODE to enter the ECO MODE screens, as shown in Figure 25.

Figure 25 ECO Mode screen

Operation and Display Panel

Press the Up or Down button to move the cursor to the required item, and press the Enter button to confirm the settings.

Outlet1 Screen

Select MAIN MENU > 2 CONFIGURATION > 4 OUTLET1 to enter the OUTLET1 screen. This menu has two submenus, as shown in Figure 26.

Figure 26 Outlet1 screen

23 Liebert® GXT4

™

Select 1 OUTLET CONTROL and press the Enter button to enter the OUTLET CONTROL screen, as

OUTLET CONTROL

TURN OFF

REBOOT

Outlet Control is On Outlet Control is Off

OUTLET CONTROL

TURN ON

TURN OFF WHEN UPS ON OVERLOAD AND ON BATTERY

TURN OFF WHEN UPS ON BATTERY FOR

OFF TURN ON WHEN POWER RETURNS:

0 MINS

TURN OFF WHEN RUNTIME LESS THAN

OFF TURN ON WHEN POWER RETURNS:

0 MINS

TURN OFF WHEN BATT CAPACITY LESS THAN

OFF TURN ON WHEN POWER RETURNS:

0 MINS

TURN ON DELAY

0 MINS

shown in Figure 27.

Figure 27 Outlet Control screen

Press the Up or Down button to move the cursor to the required item, and press the Enter button to confirm the settings.

Select 2 Outlet Setting and press the Enter button to enter the OUTLET SETTING screen, as shown in Figure 28.

Figure 28 Outlet Setting screen

Operation and Display Panel

Press the Up or Down button to move the cursor to the required item, and press the Enter button to confirm the settings.

Liebert® GXT4

™

Outlet2 Screen

APPLY THE SAME

SETTINGS AS OUTLET1

YES NO

1 LANGUAGE

2 COLOR

1 English

The Outlet2 screens are the same as the Outlet1 screens. The same settings are available as on the Outlet1 screen. If the Outlet2 group will have the same settings as the Outlet1 group, the Liebert GXT4 offers a programming shortcut, as shown in Figure 29. When configuring the Outlet2 group, the select YES and press the Enter button to apply the Outlet1 settings to the Outlet2 screen.

Figure 29 Outlet2 setting screen

LCD screen

Select Main Menu -> 2 CONFIGURATION -> 6 LCD to enter the LCD screen. This menu has two submenus, LANGUAGE and COLOR, as shown in Figure 30.

Operation and Display Panel

Figure 30 LCD screen

Select 1 LANGUAGE and press the Enter button to enter the LANGUAGE screen, as shown in Figure 31.

The Liebert GXT4 is capable of supporting multiple languages. For the list of supported languages and instructions on how to upload them, refer to the Configuration Program user manual on the included CD.

Figure 31 Language screen

25 Liebert® GXT4

™

Select ‘2 COLOR’ and press the Enter button to enter the COLOR screen, as shown in Figure 32.

EMERSON EMERSON EMERSON EMERSON

RESET ALL SETTINGS TO FACTORY DEFAULT SETTINGS?

YES NO

1 TURN ON & OFF

2 ALARM CONTROL 3 BATT TEST

Figure 32 Color screen

FACTORY DEFAULT screen

Select MAIN MENU -> 2 CONFIGURATION -> 7 FACTORY DEFAULT to enter the FACTORY DEFAULT screen, as shown in Figure 33.

Figure 33 Factory Default screen

Operation and Display Panel

Control Screen

Select MAIN MENU -> 3 CONTROL to enter the CONTROL screen. This screen has three submenus, TURN ON & OFF, ALARM CONTROL and BATT TEST, as shown in Figure 34.

Figure 34 Control screen

In the CONTROL screen, press the Up or Down button to move the cursor to the required item, and press the Enter button to enter its submenu.

Liebert® GXT4

™

TURN ON & OFF screen

TURN ON UPS

UPS is Off UPS is On

TURN OFF UPS

TURN ON UPS BYPASS

1 AUDIBLE ALARM ON

2 AUDIBLE ALARM OFF

1START

2 CANCEL 3 BATT TEST RESULT

Select MAIN MENU -> 3 CONTROL -> 1 TURN ON & OFF to enter the TURN ON & OFF screen. This screen shows one of two displays, TURN ON UPS and TURN OFF UPS, depending on the state of the UPS, as shown in Figure 35.

Figure 35 Turn UPS On or Off screen

ALARM CONTROL screen

Select MAIN MENU -> 3 CONTROL -> 2 ALARM CONTROL to enter the ALARM CONTROL screen, as shown in Figure 36. This section allows active audible alarms to be silenced. To completely turn off the audible alarm, refer to CONFIGURATION > UPS as shown in Figure 23.

Operation and Display Panel

Figure 36 Alarm Control screen

BATT TEST screen

Select MAIN MENU -> 3 CONTROL -> 3 BATT TEST to enter the BATT TEST screen, as shown in Figure 37.

Figure 37 Batt Test screen

27 Liebert® GXT4

™

Log Screen

1VIEW LOG

2 CLEAR LOG

255 OD 1H 17m AGO UPS switch to Online mode

254 /255

DO YOU WANT TO

CLEAR EVENT LOGS?

YES NO

PN: GXT4 -2000 RT230

SN:1XXX60XXX1AFCXX

FW VER: U100D100 HW VER: H100

Select MAIN MENU -> 4 LOG to enter the LOG screen. This screen has two submenus, VIEW LOG and CLEAR LOG, as shown in Figure 38.

Figure 38 Log screens

CLEAR LOG Screen

Select MAIN MENU > LOG > CLEAR LOG to enter the CLEAR LOG screen, as shown in Figure 39.

Figure 39 Clear Log screen

Operation and Display Panel

Press the Up or Down button to move the cursor to the required item. Press the Enter button to confirm the settings.

ABOUT Screen

Select MAIN MENU> ABOUT to enter the ABOUT screen, as shown in Figure 40. The ABOUT screen displays UPS model, serial number, software version and hardware version.

Figure 40 About screen

Liebert® GXT4

™

Network

ADDRESS MAC

00-02-11-4X-AX

ADDRESSIPV4

10.163.226 .231 /24

ADDRESSIPV6 AUTO

ADDRESSIPV6 STATIC

ADDRESSIPV6 LINK

Fe80::202 :99ff:fe 0f:4ba 2%1

Select MAIN MENU>NETWORK to enter the NETWORK screen.

Operation and Display Panel

The NETWORK screen displays the MAC address and the IPv4 IP address. If the Liebert GXT4 is fitted with an optional Liebert IntelliSlot IPv6 IP address settings (IPv6 requires configuration), as shown in Figure 41.

Figure 41 Network screens

Web card (Liebert IS-WEBCARD), the screen will display

29 Liebert® GXT4

™

3.4.4 Prompt List

A prompt screen is displayed during the operation of the system to alert you to certain conditions and/or to require your confirmation of a command or other operation. See Table 5 for the prompts and meanings.

Table 5 System prompts and meanings

Prompt Meanings

Mains Power Restored

UPS Return From A Low Battery Condition The UPS transfers back to mains (AC) mode from battery low mode.

UPS Return From Battery Mode The UPS transfers back to mains (AC) mode from battery mode.

UPS Self Test Successful The UPS self-test is successfully performed.

UPS Shutdown Command Received The UPS shut down was initiated through communication.

UPS Turn Off The UPS shuts down and has no output power.

UPS Turn On

UPS Shutdown Process Had Been Cancelled

ECO Mode Enabled The UPS is configured to ECO mode operation,

ECO Mode Disabled

UPS Internal Temperature Return To Normal

UPS Load Return From Overload

Load On Inverter The inverter is on and supplies protected power to the load.

Load On ECO Bypass

OUTLET1 Closed Auto / Manual

OUTLET1 Open Auto / Manual

OUTLET2 Closed Auto / Manual

OUTLET2 Open Auto / Manual

Bypass Power Restored

Operation and Display Panel

The mains power returns and the UPS transfers back to mains (AC) mode.

The UPS starts up successfully and supplies protected power to the load.

The shutdown command sent through Liebert MultiLink or SNMP card to the UPS is canceled,

The UPS is configured to Online mode, supplying protected power to the load through the inverter.

The internal temperature of the UPS recovers to normal range.

The loads are reduced, and the UPS recovers to normal state from overload.

The UPS is on ECO mode; the mains is supplying power to the load directly to reduce energy usage.

The programmable output receptacle 1 received a turn-off command and is turned Off.

The programmable output receptacle 1 received a Turn-On command and is turned On

The programmable output receptacle 2 received a Turn-Off command and is turned Off.

The programmable output receptacle 2 received a turn-on command and is turned On.

The bypass power recovered and the UPS can now transfer to bypass.

3.4.5 Warning List

All UPS warning messages are described in Table 6.

Table 6 Warning list

Warning Description

Mains Power Not Available

UPS Batteries Low And Exhausted Soon The battery capacity is low and will be exhausted soon

UPS Has Switched To Battery Mode

Load On Bypass

Input Power Wiring Error L-N line reverse or PE not connected.

Bypass Power Not Available

UPS Maintenance Bypass Output The UPS transfers to maintenance bypass.

Liebert® GXT4

™

The mains power is not available, or it cannot satisfy the input requirements for the UPS to operate from mains power

The mains power is abnormal or the PFC side is faulty, the UPS transfers back to Battery mode

The UPS transfers to Bypass mode, at this point, the input mains power supplies power to the load directly, and the load is not protected

The bypass power is not available, or it cannot satisfy the requirements for the UPS transfers to bypass

3.4.6 Fault List

All UPS fault messages are described in Table 7.

Table 7 Fault list

Fault Description

UPS Self-Test Failed The battery is bad or weak or not connected.

UPS Overload The UPS is overloaded.

Inverter Out Of Order The inverter has failed.

Battery Weak/Bad The battery is bad or weak.

Output Short Circuit The output connection is short-circuited.

DC Bus Overvoltage The DC bus is faulty.

UPS Overtemperature Overtemperature occurs to the UPS and the UPS will transfer to Bypass mode.

Charger Out Of Order The charger has failed.

Fan Out Of Order At least one fan is failed.

DC Bus Discharge Fail DC-DC failure occurs.

Rectifier Out Of Order Rectifier failure occurs.

If a fault occurs, the UPS automatically switches to Bypass Mode. The original operating mode will be maintained only in the case of a battery disconnection fault. The fault message alternates with UPS Mode once a second, the red fault indicator on the operation and display panel lights up and the alarm sounds continuously.

Operation and Display Panel

If a fault occurs:

1. Enter the ALARM CONTROL screen (see Figure 36), and select AUDIBLE ALARM ON or AUDIBLE ALARM OFF to switch the alarm On or Off.

2. Enter the EVENT LOG screen (see Figure 38), and select VIEW LOG to view the entire Event log.

NOTE

There will be a short delay before the EVENT LOG screen displays the historical fault log to allow the log to load.

31 Liebert® GXT4

™

4.0 OPERATION

This section describes checks to be made before starting the UPS, how to start the UPS, manual battery test, manual bypass, shutting down the UPS and disconnecting mains power from the UPS.

NOTE

The Liebert GXT4’s battery has been fully charged before delivery, but some charge will be lost during storage and shipping. To ensure that the battery has adequate reserve power to protect the connected load, charge the battery for three hours before putting the UPS into service.

4.1 Startup Checklist for the Liebert GXT4

Before starting the UPS, perform these checks:

___ 1. Check that the input plugs and loads are connected properly and reliably.

___ 2. Check that the battery cable is connected properly.

___ 3. Check that the communication cables are connected properly.

4.2 Starting the UPS

1. Plug the UPS into the appropriate AC outlet.

2. 3000VA models only: Close the input breaker on the rear of the unit.

3. The UPS will begin the startup sequence once AC power is present. The UPS will sound an

audible alarm, this is normal.

4. On the LCD, press either the Up or Down button once, then press the Enter button to turn On the UPS. The UPS will sound the audible alarm again as the output receptacles are now being

5. Check the LCD and LED indicators to ensure that the UPS is operating normally.

6. Check the load percentage on the default screen to ensure that the connected equipment is not exceeding the UPS’s rated capacity.

Operation

The UPS is now providing conditioned and protected power to the connected equipment.

4.3 Manual Battery Test

To initiate a manual battery test, select MAIN MENU > CONTROL>BATT TEST>START.

• If the battery test results show FAILED, allow the UPS to recharge the batteries for 24 hours.

• Retest the batteries after 24 hours of charging.

• After the batteries have been retested, if the battery test still shows FAILED, contact your local Emerson

representative or Emerson Network Power Channel Support.

4.4 Manual Bypass

To manually transfer the connected equipment to the internal bypass:

1. From the main menu select Control then press enter.

2. Select TURN ON & OFF and press Enter.

3. Select TURN UPS BYPASS and press Enter. The UPS will transfer the connected loads to the internal bypass.

If the internal bypass is not available because of input power problems, pressing this button once will be ignored. Bypass operation is indicated by an audible alarm and illuminated amber Bypass indicator. (If other indicators are illuminated, refer to 7.0 - Troubleshooting.)

Liebert® GXT4

™

4.5 Shut Down the Liebert GXT4

To shut down the UPS from the LCD:

1. From the Main Menu select CONTROL, press Enter, then select TURN ON & OFF.

2. Press the Enter key.

3. Select TURN UPS OFF, then press Enter. Press either the Up or Down button to move the cursor to confirm the turn off command and press Enter. The UPS will sound an audible alarm; this is

normal.

4. Power to the connected equipment is now Off.

The UPS display will still be illuminated because the batteries are still being charged. The UPS may now be disconnected from AC power, and the UPS will completely shut down in approximately 15 seconds.

4.6 Disconnecting Input Power from the Liebert GXT4

1. After the UPS has been shut down as detailed in 4.5 - Shut Down the Liebert GXT4, disconnect the input cable from the wall socket.

2. Wait 30 seconds and verify that all indicators have turned Off and the fan has stopped; this indicates that the power-off is complete.

3. Turn the external battery cabinet breaker switch to the Off position if the UPS has an external battery cabinet.

After powering Off the UPS, the UPS ceases output and the load is powered Off.

Operation

33 Liebert® GXT4

™

5.0 COMMUNICATION

This section describes the four types of communication ports on the rear of the UPS:

• Liebert IntelliSlot

• USB port (standard B-type)

• Terminal Block Communication

•RS232 port (DB9F)

port

CAUTION

To maintain safety (SELV) barriers and for electromagnetic compatibility, signal cables should be segregated and run separate from all other power cables.

5.1 Liebert IntelliSlot Communication Cards

The Liebert IntelliSlot port accepts four optional cards:

• Liebert IntelliSlot Web Card (IS-WEBCARD)

• Liebert IntelliSlot Relay Card (IS-RELAY)

• Liebert IntelliSlot MultiPort Card (IS-MULTIPORT)

• Liebert IntelliSlot Unity Card (IS-UNITY-DP)

The Liebert IntelliSlot Web Card provides SNMP monitoring and control of the UPS across the network.

Communication

The Liebert IntelliSlot Relay Card provides dry contact relay outputs for custom-wired applications and delivers support for Liebert MultiLink

The Liebert IntelliSlot MultiPort Card provides four sets of contacts for support of up to four computers that have Liebert MultiLink installed.

The Liebert IntelliSlot Unity Card provides SNMP and/or RS-485 monitoring of the UPS across the network and/or building management system. The Liebert IntelliSlot UNITY card also enables monitoring external temperature, humidity and contact closure inputs using external sensors. (The Liebert IS-UNITY-DP compatibility will be a future release, contact your Emerson sales representative for availability.)

Follow instructions provided with the Liebert IntelliSlot card to configure Liebert MultiLink UPS or any additional ancillary product for the Liebert GXT4. These instructions are available at:

multilink.liebert.com

5.1.1 Liebert MultiLink

Liebert MultiLink monitors the UPS continuously and can shut down the computer or server in the event of an extended power failure. Liebert MultiLink can also be configured to shut down the UPS.

Liebert MultiLink can communicate with the UPS via the USB port, RS232 port, contact closures via terminal block or over the network via SNMP using the Liebert IS-WEBCARD. An optional Liebert MultiLink license kit permits shutting down multiple computers that are protected by the UPS.

For more information about the Liebert IntelliSlot SNMP Card, Liebert IntelliSlot Web Card and Liebert MultiLink License Kits, visit the Liebert Web site (www.liebert.com) or contact your local Emerson

representative.

shutdown software.

, the

5.2 USB Port Communication

The standard B-type USB port is used to connect the UPS and network server or other computer system using Liebert MultiLink

A standard B-type USB port is provided to allow connection to a computer or network server. The USB port can be used to communicate with the Liebert GXT4 configuration program (see section5.2.1 - Configuration Program for details) or Liebert MultiLink (refer to 5.1.1 - Liebert MultiLink for description) that is provided on the CD that is included with the UPS.

Liebert® GXT4

™

5.2.1 Configuration Program

The configuration program is on the Liebert GXT4 CD and can be used instead of making configuration setting changes from the LCD panel. The configuration program communicates to a computer running a Microsoft

For most users, the factory default settings are adequate. This section give a brief overview of the features and parameters that are available for modification, as well as the factory default settings. Should any changes be necessary, refer to the Configuration Program User Manual that is located on the included CD for further details.

The configuration program allows these features of the Liebert GXT4 to be changed:

• Change and set the display language

• Enable/Disable Auto-Restart (default is Enable)

• Select frequency converter operation with a fixed output frequency of 50Hz or 60Hz, bypass disabled (default is Auto-Select with bypass enabled)

• Set the Low Battery Warning alarm time from 2 to 30 minutes (default is 2 minutes)

• Enable/Disable the Auto-Battery test (default is Enable)

• Enable/Disable Auto-Restart after removing Remote shutdown (default is Disable)

• Set the wiring mode of Remote shutdown (default is normally open)

• Set the Auto-Enable output after remote shutdown (default is Disable)

• Set the Auto-Battery test to 8, 12, 16, 20, or 26 weeks (default is 8 weeks)

• Select the number of external battery cabinets connected to the UPS to adjust the remaining run time calculated by Emerson

• Select one of multiple output voltages to match various voltages (see Table 8).

Table 8 Output voltage option

UPS Model

GXT4-500RT120 - GXT4-3000RT120 120 110, 115, 120 and 127

GXT4-3000RT208 208 208 / 220 / 230 / 240

Windows® operating system via the included USB cable.

software products (default is zero)

Factory

Default, VAC Output Voltage Option, VAC

Communication

NOTICE

The output voltage settings cannot be changed while the UPS is On and powering connected loads.

NOTE

• Setting the output voltage of the Liebert GXT4-500RT120, GXT4-700RT120, and GXT4-1000RT120 models to 110VAC automatically derates both the VA and Watt ratings to 95% of the unit’s rating.

• Setting the output voltage of the Liebert GXT4-1500RT120 and GXT4-2000RT120 models to 110VAC automatically derates both the VA and Watt ratings to 85% of the unit’s ratings, and programming the output voltage to 115VAC automatically derates both the VA and Watt ratings to 95% of the unit’s rating.

• Setting the output voltage of the Liebert GXT4-3000RT120 model to 110VAC automatically derates both the VA and Watt ratings to 90% of the unit’s ratings (refer to 9.0 - Specifications for the VA and Watt ratings).

NOTE

• This program is compatible with UPS models beginning with ‘GXT4,’ as in ‘GXT4-3000RT230.’ It is not compatible with earlier versions of the Liebert GXT UPS.

• A computer running Microsoft Windows 7 or Windows 8 is required to set up and run the configuration program.

Windows 2000®, Windows XP®, Windows Vista®,

35 Liebert® GXT4

™

5.3 RS-232 Port

3 4

5 6

7 8

Low Battery

On Battery Mode

Battery Mode Shutdown

Any Mode Shutdown

The RS-232 port uses an Emerson® proprietary protocol that is for use with Liebert MultiLink®. This port enables a more secure connection instead of the USB cable, to the computer or server that has Liebert MultiLink installed.

5.4 Terminal Block Communication

The Terminal Block includes eight pins, as shown in Figure 42.

Figure 42 Terminal Block Communication pin layout

Communication

5.4.1 Any Mode Shutdown

The purpose of Any Mode Shutdown is to shut down the UPS output by turning Off the rectifier, inverter and static switch so that there is no power to the loads.

Any Mode Shutdown can be operated locally or remotely:

• Local Any Mode Shutdown can be performed by shorting Pin 1 and Pin 2.

• Remote Any Mode Shutdown can be performed using a switch connected to Pin 1 and Pin 2 and mounted at a remote location.

NOTE

Remote Power Off will be performed either by NO or NC contact of Any Mode Shutdown, depending on the settings in the configuration program.

A current-limited source for this optocoupler (+12VDC, 50mA) will be available from the UPS.

The connection to the UPS for remote connection will be via terminal block connector.

Any Mode Shutdown wiring must conform to all national, regional and local wiring regulations.

WARNING

When the Auto-Enable output option is selected and the UPS output is disabled using Pin 1 and Pin 2, the Liebert GXT4’s output can turn On automatically and without warning if the Pin 1 and Pin 2 connection is changed.

Liebert® GXT4

™

5.4.2 Battery Mode Shutdown

Battery Mode Shutdown permits shutting down the UPS by turning Off the rectifier, inverter and static switch so that there is no power to the load when the UPS is On Battery. The auxiliary power for the UPS will still be active.

Battery Mode Shutdown can be performed locally or remotely:

• Local Battery Mode shutdown can be performed by shorting Pin3 and Pin4.

• Remote Battery Mode Shutdown can be performed using a switch connected to Pin3 and Pin4 and mounted at remote location.

NOTE

Remote Power Off will be performed by NO contact.

A current-limited source (+12VDC, 50mA) will be available from UPS.

The connection to the Liebert GXT4 for remote connection will be via terminal block connector.

Battery Mode Shutdown wiring must conform to all national, regional and local wiring codes and laws.

This signal must last for 1.5 seconds or longer.

A battery shutdown signal will not cause an immediate shutdown. It will start a 2-minute shutdown timer. This timer cannot be stopped once triggered. If the mains power returns during this countdown, the Liebert GXT4 will still shut down and must remain shut down for 10 seconds. Whether the UPS turns back On when the power is restored depends on the auto-restart setting.

Communication

5.4.3 On Battery

On Battery signal is a Normally Open (NO) dry contact. When the UPS is supplying output power from the battery this dry contact will be closed.

5.4.4 Low Battery

Low Battery signal is a Normally Open (NO) dry contact. When the UPS is supplying output power from the battery and has reached the Low Battery Warning time selected in the configuration program, this dry contact will be closed.

NOTE

The rated values for the dry contacts for the On Battery and Low Battery signals are:

• Rated Voltage: 30V (AC or DC)

• Rated Current: 300mA

37 Liebert® GXT4

™

6.0 MAINTENANCE

This section describes replacing the internal battery pack, precautions, checking the Liebert GXT4’s status and checking UPS functions.

WARNING

The battery can present a risk of electrical shock and high short circuit current. The following precautions should be observed before replacing the battery pack:

• Remove rings, watches and other metal objects.

• Use tools with insulated handles.

• Do not lay tools or other metal objects on the batteries.

• If the battery kit is damaged in any way or shows signs of leakage, contact your local Emerson representative immediately.

• Do not dispose of batteries in a fire. The batteries may explode.

• Handle, transport and recycle batteries in accordance with local regulations.

6.1 Replacing the Internal Battery Pack

The Liebert GXT4 is designed to allow the user to replace the internal battery pack safely. Refer to Table 9 for internal battery pack part numbers for Liebert GXT4 UPS:

Table 9 Replacement internal battery pack model number

UPS Model Number

Liebert GXT4-500RT120 GXT4-5A48BATKIT 1

Liebert GXT4-700RT120 GXT4-5A48BATKIT 1

Liebert GXT4-1000RT120 GXT4-5A48BATKIT 1

Liebert GXT4-1500RT120 GXT4-9A48BATKIT 1

Liebert GXT4-2000RT120 GXT4-9A48BATKIT 1

Liebert GXT4-3000RT120 GXT4-9A72BATKIT 1

Liebert GXT4-3000RT208 GXT4-9A72BATKIT 1

Replacement Internal Battery

Pack Model Number

Maintenance

Quantity

Required

Read all safety cautions before proceeding. A trained user can replace the internal battery pack when the UPS is always in a restricted access location (such as a rack or server closet). Contact your local dealer or Emerson representative to obtain the pricing of the appropriate replacement battery pack.

CAUTION

Risk of explosion if battery is replaced by an incorrect type. Dispose of used batteries according to the instructions.

Liebert® GXT4

™

6.1.1 Battery Replacement Procedures

Battery Connector

Battery Receptacle

Internal Battery Pack

Battery Handle

Pull Out with Battery Handle

1. Remove the front plastic bezel cover from the UPS.

2. Loosen and remove the six screws on the battery door, as shown in Figure 43.

3. Lay the battery door and screws aside for reassembly.

Figure 43 Removing the front bezel cover and battery door

Maintenance

4. Gently pull the battery wire out and disconnect the battery plug and battery receptacle, as shown in Figure 44.

Figure 44 Disconnecting the battery plug and battery receptacle (front view)

5. Grasp the battery handle, and pull the internal battery pack out of the UPS, as shown in Figure 45.

Figure 45 Pull out the battery

39 Liebert® GXT4

™

6. Unpack the new internal battery pack. Take care not to destroy the packing. Compare the new and old internal battery pack to make sure they are the same type and model. If

so, proceed with Step 7; if they are different, stop and contact your local Emerson representative, or Emerson Channel Support.

7. Line up and slide in the new internal battery pack.

8. Reconnect the battery plug and battery receptacle

9. Push the battery wire and internal battery pack back into the UPS.

10. Reattach the front battery door with the six screws.

11. Reattach the front plastic bezel cover to the UPS.

NOTE

The internal battery pack is hot-swappable. However, caution should be exercised because during this procedure the load is unprotected from disturbances and power outages. Do not replace the battery while the UPS is operating in Battery Mode. This will result in a loss of output power and will drop the connected load.

6.2 Battery Charging

The batteries are valve-regulated, nonspillable, lead acid and should be kept charged to attain their design life. The Liebert GXT4 charges the batteries continuously when it is connected to the utility input power.

If the Liebert GXT4 will be stored for a long time, Emerson recommends connecting the UPS to input power for at least 24 hours every four to six months to ensure full recharge of the batteries.

Maintenance

6.3 Precautions

Although the Liebert GXT4 has been designed and manufactured to ensure personal safety, improper use can result in electrical shock or fire. To ensure safety, observe the following precautions:

• Turn Off and unplug the Liebert GXT4 before cleaning it.

• Clean the UPS with a dry cloth. Do not use liquid or aerosol cleaners.

• Never block or insert any objects into the ventilation holes or other openings of the Liebert GXT4.

• Do not place the Liebert GXT4 power cord where it might be damaged.

6.4 Checking UPS Status

Emerson recommends checking the UPS operation status every six months.

• Check if the UPS is faulty: Is the Fault Indicator On? Is the UPS sounding an alarm?

• Check if the UPS is operating in Bypass mode: Normally, the UPS operates in Normal Mode; if it is operating in Bypass Mode, stop and contact your local Emerson representative or Emerson Channel Support.

• Check if the battery is discharging: When the utility input is normal, the battery should not discharge. If the UPS is operating in Battery Mode, stop and contact your local Emerson representative or Emerson Channel Support.

6.5 Checking UPS Functions

NOTE

UPS function check procedures may interrupt power supply to the connected load.

Emerson recommends checking the UPS functions once every six months.

Back up the load data before conducting the UPS functions check. Procedures are as follows:

1. Press the Standby/Manual Bypass button to check whether the alarm and indicators are normal.

2. Press the On/Alarm Silence/Manual Battery Test button to check again whether the indicators are On and the UPS is operating normally.

3. Press the On/Alarm Silence/Manual Battery Test button for three seconds after Inverter Mode; the UPS should initiate battery self-test. Check to determine whether the battery is operating normally. If not, stop and contact your local Emerson representative or Emerson Channel Support.

Liebert® GXT4

™

7.0 TROUBLESHOOTING

This section indicates various UPS symptoms a user may encounter and provides a troubleshooting guide in the event the UPS develops a problem. Use the following information to determine whether external factors caused the problem and how to remedy the situation.

7.1 UPS Symptoms

The following symptoms indicate the Liebert GXT4 is malfunctioning:

• The relative indicators illuminate, indicating the UPS has detected a problem.

• An alarm buzzer sounds, alerting the user that the UPS requires attention.

7.1.1 Indicator and LCD

In addition to the fault indicator being illuminated, the LCD will display the fault. The displayed fault on the LCD is described in Table 10

Table 10 Description of the displayed fault

Displayed Fault Cause Corrective Steps

UPS self test failed The battery is bad or weak. Contact customer service.

UPS shutdown command received

UPS overload The UPS is overloaded.

Inverter Out of Order The inverter is faulty. Contact customer service.

Battery Weak/Bad The battery is bad or weak. Replace the battery.

Output Short Circuit The output connection is short-circuited.

DC Bus Overvoltage The DC bus is faulty. Contact customer service.

UPS Overtemperature

Charger Out of Order The charger is faulty. Contact customer service.

Fan Out of Order At least one fan is faulty. Contact customer service.

DC Bus Discharge Fail A DC-DC failure occurs. Contact customer service.

The UPS shuts down through communication.

Over-temperature occurs to the UPS and the UPS will transfer to Bypass mode.

Troubleshooting

Contact customer service.

Reduce the load and contact customer service.

Shut down the equipment and contact customer service.

Reduce the load and contact customer service.

NOTE

If the UPS encounters a fault and no correction attempt is performed within 2 minutes, the LCD backlight will flash (on 1 second and off 1 second) as an alert.

Press any button to exit the alert mode. If no correction attempt is performed on the UPS, the LCD backlight will flash again until the UPS fault is corrected.

41 Liebert® GXT4

™

7.1.2 Audible Alarm

An audible alarm will sound in conjunction with the visual indicators to indicate a change in UPS operating status. The audible alarm will sound as described in Table 11.

Table 11 Audible alarm description

Condition Alarm

Battery discharge Half-second beep every 10 seconds

Low battery Two half-second beeps every 5 seconds

UPS fault, load on bypass 1-second beep every 4 seconds

UPS fault, no power to load Continuous

Overload Half-second beep every half second

Battery replacement 2-second beep every 2 minutes

Battery loss Continuous

Wiring problem (loss of proper grounding for UPS) Continuous

Bypass reminder 1-second beep every 60 seconds

7.2 Troubleshooting

Troubleshooting

In the event of an issue with the UPS, refer to Table 12 to determine the cause and solution. If the fault persists, contact Emerson

Channel Support.

Table 12 Troubleshooting table

Problem Cause Solution

UPS fails to start

Battery indicator is illuminated

UPS has reduced battery backup time

Battery indicator is flashing.

Bypass indicator is flashing.

UPS is short-circuited or overloaded

Batteries are not charged enough or not connected

UPS is not plugged in

UPS input protection fuse has blown/opened

Mains power is out of tolerance

Batteries are not fully charged

UPS is overloaded Check load level indicator and reduce the load on the UPS.

Batteries may not be able to hold a full charge due to age

Battery source is not available; continuous horn.

Because the voltage or frequency is outside acceptable limits, the bypass is disabled.

Ensure UPS is Off. Disconnect all loads and ensure nothing is lodged in output receptacles. Ensure loads are not defective or shorted internally.

Check to ensure the internal battery is connected. If it is not, make the connection and try to start the unit. If the battery is connected, leave the UPS connected to input power for 24 hours to recharge batteries, then try to start the unit.

UPS is operating from battery mode. Ensure UPS is securely plugged into the wall receptacle.

UPS is operating from battery mode. Save data and close applications. Replace UPS input fuse, then restart UPS.

UPS is operating from battery mode. Save data and close applications. Ensure mains supply voltage is within acceptable limits for UPS.

Keep UPS plugged in continuously at least 24 hours to recharge batteries.

Replace batteries. Contact your local dealer, Emerson representative or Emerson Channel Support for replacement battery kit.

Check battery connections, completely power down and restart UPS. NOTE: If the battery circuit opens while the UPS is running, it will be detected when the next battery test is performed.

The AC input powers the PFC input and serves as the bypass source. If the AC is present but the voltage or frequency exceeds the acceptable range for safe operation with a load, the bypass will be disabled and this indicator will flash, indicating that the bypass is unavailable.

When reporting a UPS issue to Emerson, include the UPS model and serial number. These are located in several places for your ease of location: on the top panel (rack mount orientation); the left side (tower orientation); the rear panel; on the front of the unit behind the front plastic bezel; and on the LCD select Main Menu > About.

Liebert® GXT4

™

8.0 BATTERY CABINET

Battery Connectors

Isolation Breaker

Optional battery cabinets are available for the Liebert GXT4. The battery connectors and input breaker are on the battery cabinet’s rear panel, as shown in Figure 46. For battery cabinet specifications, refer to Table 15. The Liebert GXT4 may be equipped with a maximum of six extension battery packs.

For battery run times, refer to Table 17.

Figure 46 Battery cabinet

Battery Cabinet

WARNING

Do not contact the battery connectors and ground without wearing protective gloves and clothing and taking other precautions against electrical shock. The battery loop and AC input are not insulated, which may cause a dangerous voltage between the battery connectors and ground.

NOTE

External Battery Connectors are wired in parallel. Either connector can be connected to the UPS or to another battery cabinet.

NOTE

The standard battery cable delivered with the battery cabinet is 0.65m (2.13ft) long

43 Liebert® GXT4

™

9.0 SPECIFICATIONS

Table 13 Specifications of GXT4-500RT120 - GXT4-700RT120 and GXT4-1000RT120 models

Product Model

Parameters

Dimensions, D × W × H, in. (mm)

Shipping

Weight, lb (kg)

Shipping 47 (21.4)

Input AC

Voltage Range (typical) 120VAC nominal; variable based on output load

90% ~ 100% loading 90VAC/140VAC

70% ~ 90% loading 86VAC/140VAC

30% ~ 70% loading 77VAC/140VAC

0 ~ 30% loading 60VAC/140VAC

Frequency 40Hz ~ 70Hz; Auto Sensing

Input Power Cord 10 ft. attached w/ NEMA 5-15P plug

Output AC

Output Receptacles 5-15R × 6

Voltage 110/115/120VAC (user-configurable); ±3%

Waveform Sine wave

Utility (AC) Mode Overload 200% for 2 seconds; 150% for 50 seconds with transfer to bypass

Battery

Type Valve-regulated, nonspillable, lead acid

Qty × V× Rating 4 × 12V × 5.0Ah

Battery Mfr./Part # YUASA/NPH5-12; CSB/ HR 1221W; CSB/GP1245

Backup Time See Table 17

Recharge Time

Environmental Requirements

Operating Temperature, °F (°C) 32 to 104 (0 to 40); see Table 16 - Operating temperature parameters

Storage Temperature, °F (°C) 5ºF to 122ºF (-15ºC to 50ºC)

Relative Humidity 0% to 95%, non-condensing

Operating Elevation Up to 10,000 ft. (3000m) at 77ºF (25ºC) without derating

Storage Elevation 50,000 ft. (15000m) maximum

Audible Noise

Agency

Safety UL 1778, cUL Listed

RFI/EMI FCC Class A

Surge Immunity IEC 62040-2 2nd Ed

Transportation ISTA Procedure 1A

GXT4-500RT120

(500VA/450W)

Unit

Unit 40 (18.2)

3 Hours to 90% capacity after full discharge with 100% load till UPS auto-shutdown

<43dBA max @ 3ft. (1m) front and sides

<46dBA max @ 3ft. (1m) rear

GXT4-700RT120

(700VA/630W)

16.2 x 16.9 x 3.4 (408 x 430 x 85)

25.5 x 23.9 x 10.6 (647 x 607 x 270)

(Internal Batteries Only)

GXT4-1000RT120

(1000VA/900W)

< 50 dBA, at 3ft. (1m) rear

< 45 dBA, at 3ft. (1m) front and sides

Specifications

Liebert® GXT4

™

Specifications

Table 14 Specifications of GXT4-1500RT120 - GXT4-3000RT120 and GXT4-3000RT208 models

Product Model

GXT4-1500RT120

Parameters

(1500VA/1350W)

Dimensions, D × W × H, in. (mm)

Unit

Shipping

19.7 x 16.9 x 3.4 (497 × 430 × 85)

25.5 x 23.9 x 10.6 (647 x 607 x 270)

Weight, lb. (kg)

Unit 54.6 (24.8) 56.1 (25.5) 71.4 (32.4)

Shipping 69.6 (31.6) 70.5 (32) 86 (39)

Input AC

Voltage Range (typical) 120VAC nominal; variable based on output load

90 - 100% loading 102VAC/140VAC 177VAC/280VAC

70 - 90% loading 96VAC/140VAC 168VAC/280VAC

30 - 70% loading 84VAC/140VAC 150VAC/280VAC

0 - 30% loading 60VAC/140VAC 115VAC/280VAC

Frequency 40 - 70Hz; Auto Sensing

Input Power Cord

10 ft. attached w/

NEMA 5-15P plug

Output AC

Output Receptacles 5-15R × 6 5-20R × 6

Voltage 110/115/120VAC (user-configurable); ±3%

Waveform Sine wave

Utility (AC) Mode Overload

200% for 2 seconds

150% for 50 seconds

Battery

Type Valve-regulated, nonspillable, lead acid

Qty×V×Rating 4 × 12V × 9.0Ah 6 × 12V × 9.0Ah 6 × 12V × 9.0Ah

Battery Mfr./Part # Panasonic/UP- RW1245; CSB/HR 1234W F2; CSB UPS12460F2

Backup Time See Table 17

Recharge Time

to 90% capacity after full

discharge with 100% load till

4 Hours 3 Hours

UPS auto-shutdown (Internal

Batteries Only)

Environmental

Operating Temperature, °F (°C) +32 to +104 (0 to 40); see Table 16 - Operating temperature parameters

Storage Temperature, °F (°C) 5 to +122 (-15 to 50)

Relative Humidity 0% to 95%, non-condensing

Operating Elevation Up to 10,000 ft. (3000m) at 77ºF (25ºC) without derating

Storage Elevation 50,000 ft. (15000m) maximum

< 45dBA at 3ft (1m) rear

Audible Noise

< 46 dBA at 3ft. (1m)

front and side

Agency

Safety UL 1778, c-UL Listed

RFI/EMI FCC Class A

Surge Immunity IEC 62040-2 2nd Ed

Transportation ISTA Procedure 1A

GXT4-2000RT120

(2000VA/1800W)

10 ft. attached w/

NEMA 5-20P plug

<48dBA max @ 3ft (1m) front and side

GXT4-3000RT120

(3000VA/2700W)

GXT4-3000RT208

(3000VA/2700W)

23.7 x 16.9 x 3.4 (602 × 430 × 85)

29.4 x 23.4 x 10.6 (747 x 607 x 270)

208VAC nominal;

based on output load

10 ft. attached w/

NEMA L5-30P plug

L5-

30R×1+ 5-20R × 6

10 ft. attached w/

NEMA L6-20P plug

L6-20R×1+ L6-15R×2

208/220/230/240 VAC

(user-configurable); ±3%

200% for 2 seconds

150% for 10 seconds

<48dBA max @ 3ft. (1m) rear

variable

45 Liebert® GXT4

™

Table 15 Battery cabinet specifications

Model Number

Parameter

GXT4-500RT120,GXT4-700RT120

GXT4-1000RT120,GXT4-1500RT120,

Used w/UPS Model

Dimensions, D × W × H, in (mm)

Unit

Shipping

Weight, lb (kg)

Unit 57.3 (26) 83.8 (38)

Shipping 86 (39) 110 (50)

Battery parameters

Type Valve-regulated, nonspillable, lead acid

Qty × V× Rating 2 × 4 × 12V × 9.0Ah 2 × 6 × 12V × 9.0Ah

Battery Mfr./Part # Panasonic/UP-RW1245; CSB/HR 1234W F2; CSB UPS12460F2

Backup Time See Table 17

Environmental

Operating Temperature, °F (°C) 32 to 104 (0 to 40)

Storage Temperature, °F (°C)

Relative Humidity 0% to 95%, non-condensing

Operating Elevation Up to 10,000 ft. (3000m) at 104ºF (40ºC) without derating

Storage Elevation 50,000 ft. (15000m) maximum

Agency

Safety UL 1778, c-UL Listed

RFI/EMI FCC Class A

Surge Immunity IEC 62040-2 2nd Ed

Transportation ISTA Procedure 1A

GXT4-48VBATT GXT4-72VBATT

GXT4-2000RT120

19.7 x 16.9 x 3.3 (497 × 430 × 85)

24.3 x 22.4 x 10.3 (617 x 570 x 262)

19 to 122 (-15 to 50)

High ambient temperatures will reduce battery life.

Specifications

GXT4-3000RT120 GXT4-3000RT208

23.7 x 16.9 x 3.3 (602 × 430 × 85)

28.2 x 22.4 x 10.3 (717 x 570 x 262)

Table 16 Operating temperature parameters

Ambient Temperature, °C (°F) 25-30 (77-86) 30-35 (86-95) 35 - 40 (95-104)

Maximum Output Power Factor Derating @ Maximum Load

Liebert® GXT4

™

100%-93% 93%-86% 86%-79%

Table 17 Battery run times

Number of External

Battery Cabinets

Internal Battery

+ 1 External

Battery Cabinet

Internal Battery

+ 2 External

Battery Cabinets

Internal Battery

+ 3 External

Battery Cabinets

Load Percent

of Capacity

10% 128 105 90 123 92 82 92

20% 82 61 37 52 38 38 39

30% 41 37 30 34 23 23 23

40% 38 32 23 23 16 16 16

50% 34 27 17 18 12 12 11

60% 31 22 14 14 9 9 9

70% 27 18 11 11 7 7 7

80% 23 15 9 9 5 5 5

90% 20 13 8 7 4 4 4

100% 17 11 7 6 3 3 3

10% 448 426 332 335 303 224 303

20% 329 302 165 162 140 137 139

30% 223 163 137 129 96 95 95

40% 166 144 108 96 66 66 65

50% 153 125 92 72 49 49 48

60% 139 106 74 54 38 41 41

70% 125 94 61 46 33 34 34

80% 108 78 49 38 28 27 27

90% 100 69 40 34 23 23 25

100% 92 60 38 31 20 21 21

10% 480 480 456 451 431 427 431

20% 454 433 331 318 207 202 205

30% 429 327 222 187 150 149 149

40% 333 265 166 151 124 124 123

50% 309 201 152 131 97 98 97

60% 225 164 137 107 75 76 75

70% 201 153 122 91 61 62 62

80% 166 142 105 74 50 50 50

90% 159 131 95 64 41 45 46

100% 151 120 79 53 38 41 41

10% 480 480 480 480 455 452 455

20% 480 461 441 426 326 323 325

30% 458 438 336 312 197 196 195

40% 442 344 305 198 155 155 154

50% 426 322 209 160 136 136 135

60% 338 300 167 145 111 112 112

70% 322 213 157 130 96 98 98

80% 305 189 146 111 78 79 79

90% 225 163 135 99 68 70 70

100% 209 155 124 83 56 60 60

Specifications

208VAC

120VAC RT Models

RT Model

500VA 700VA 1000VA 1500VA 2000VA 3000VA 3000VA

47 Liebert® GXT4

™

Specifications

Table 17 Battery run times (continued)

208VAC

Number of External

Battery Cabinets

Load Percent

of Capacity

500VA 700VA 1000VA 1500VA 2000VA 3000VA 3000VA

120VAC RT Models

10% 480 480 480 480 480 466 480

20% 480 480 459 446 424 421 423

30% 480 457 435 341 308 307 307

40% 460 441 339 309 192 192 191

Internal Battery

+ 4 External

Battery Cabinets

50% 448 424 316 204 157 158 157

60% 436 336 221 164 142 143 142

70% 424 318 199 153 126 128 128

80% 340 301 166 141 107 109 109

90% 327 213 158 130 95 97 98

100% 315 197 149 112 79 81 81

10% 480 480 480 480 480 480 480

20% 480 480 466 458 441 439 440

30% 480 464 446 432 333 332 331

40% 467 451 427 333 225 225 224

Internal Battery

+ 5 External

Battery Cabinets

50% 457 438 341 306 188 190 188

60% 447 424 322 207 158 159 159

70% 438 343 303 167 145 147 147

80% 428 329 212 158 133 135 135

90% 390 315 193 148 120 122 122

100% 341 300 166 139 104 107 106

10% 480 480 480 480 480 480 480

20% 480 480 480 467 452 450 451

30% 480 480 458 445 422 421 421

40% 480 462 442 422 319 319 318

Internal Battery

+ 6 External

Battery Cabinets

50% 467 451 426 327 216 218 216

60% 459 440 342 304 185 188 186

70% 451 428 326 208 159 160 160

80% 442 370 309 184 148 149 150

90% 434 336 221 161 137 139 139

100% 426 324 204 153 126 129 129

Run times in this table are approximate. Times can vary by ±5% due to manufacturing variances of the batteries. Times are based on new, fully charged batteries with 100% resistive loads and an ambient temperature of 77°F (25°C). To increase this time, turn Off non-essential loads (such as idle computers and monitors) or add optional external battery cabinets.

RT Model

Liebert® GXT4

™

9.1 Product Warranty Registration

Registration is not required to activate the product warranty on a Liebert UPS. Registration is required to qualify for the Product Protection Promise. To register, visit the Emerson Network

Power

Web site to fill out the online form at:

www.emersonnetworkpower.com/en-US/Forms/Pages/LiebertProductWarrantyRegistration.aspx

• To contact warranty support by e-mail: dpg.warranty@emerson.com

9.2 Technical Support

Technical support contacts are listed on the back cover of this document. To contact Emerson Channel Product Support:

Phone

• NORTH AMERICA: 1-800-222-5877

• OUTSIDE NORTH AMERICA: 00-800-1155-4499

E-mail

• TECHNICAL SUPPORT: liebert.upstech@emerson.com

Specifications

49 Liebert® GXT4

™

While every precaution has been taken to ensure the accuracy and completeness of this literature, Liebert Corporation assumes no responsibility and disclaims all liability for damages resulting from use of this information or for any errors or omissions. © 2014 Liebert Corporation All rights reserved throughout the world. Specifications subject to change without notice. ® Lieber t is a registered t rademark of Lieber t Corporation. All names referred to are trademarks or registered trademarks of their respective owners.

SL-23193_REV0_10-14

Technical Support / Service

Web Site

www.liebert.com

Monitoring

liebert.monitoring@emerson.com

800-222-5877

Outside North America: +00800 1155 4499

Single-Phase UPS & Server Cabinets

liebert.upstech@emerson.com

800-222-5877

Outside North America: +00800 1155 4499

Three-Phase UPS & Power Systems

800-543-2378

Outside North America: 614-841-6598

Environmental Systems

800-543-2778

Outside the United States: 614-888-0246

Locations

United States

1050 Dearborn Drive

P.O. Box 29186

Columbus, OH 43229

Europe

Via Leonardo Da Vinci 8

Zona Industriale Tognana

35028 Piove Di Sacco (PD) Italy

+39 049 9719 111

Fax: +39 049 5841 257

Asia

29/F, The Orient Square Building

F. Ortigas Jr. Road, Ortigas Center

Pasig City 1605

Philippines

+63 2 687 6615

Fax: +63 2 730 9572

Emerson Network Power

Liebert www.emerson.com

Emerson Liebert GXT4 User Manual

Specifications and Main Features

Frequently Asked Questions

User Manual