Emerson ic200bk, iC200 User Manual
Digital Tuning Stereo Clock Radio
R
with iPod® Docking Station
SmartSet® Auto Time Setting System
and Remote Control
(U.S. Patent No. 6,567,344)
OWNER’S MANUAL
iC2 00 (Silver Color)
iC2 00BK (Black Color)
Made for all iPod® models including iPod® nano, iPod® shuffle and iPod® mini
Visit our web site at www.emersonradio.com
iC200_NCab050307.p65 3/5/2007, 11:2948
!
CAUTION
TO PREVENT FIRE OR SHOCK HAZARD, DO NOT USE THIS PLUG WITH AN
EXTENSION CORD, RECEPTACLE OR OTHER OUTLET UNLESS THE BLADES
CAN BE FULLY INSERTED TO PREVENT BLADE EXPOSURE. TO PREVENT FIRE
OR SHOCK HAZARD, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE.
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
The lightning flash with arrowhead symbol, within an equilateral triangle is intended to
alert the user to the presence
of uninsulated ‘dangerous voltage’
within the product’s enclosure
that may be of sufficient
magnitude to constitute a risk
of electric shock to persons.
WARNING: TO REDUCE THE
RISK OF ELECTRIC SHOCK
DO NOT REMOVE COVER
(OR BACK), NO U SER
SERVICEABLE PARTS INSIDE
REFER SERVICING TO
Q U A LI F IE D S E R VI C E
PERSONNEL.
The exclamation point within
an equilateral triangle is intended to alert the user to
the presence of important
operating and maintenance
(servicing) instructions in
the literature accompanying the appliance.
The Caution Marking maybe located at the bottom enclosure of the apparatus.
IMPORTANT SAFETY INSTRUCTIONS
1.) Read these instructions. Keep these instructions. Follow all instructions. Heed all warnings.
2.) Do not use this apparatus near water.
3.) Clean only with dry cloth.
4.) Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions.
5.) Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus
(including amplifiers) that produce heat.
6.) Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two
blades with one wider than the other. A grounding type plug has two blades and a third grounding
prong. The wide blade or the third prong is provided for your safety. If the provided plug does not
fit into your outlet, consult an electrician for replacement of the obsolete outlet.
7.) Protect the power cord from being walked on or pinched particularly at plugs, convenience
receptacles, and the point where they exit from the apparatus.
8.) Only use attachments / accessories specified by the manufacturer.
9.) Unplug this apparatus during lightning storms or when unused for long periods of time.
10.) Refer all servicing to qualified service personnel. Servicing is required when the apparatus has
been damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled
or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture,
does not operate normally, or has been dropped.
11.) This appliance shall not be exposed to dripping or splashing water and no object filled with liquids
such as vases shall be placed on the apparatus.
12.) Use only with the cart, stand, tripod, bracket, or table specified by the
manufacturer, or sold with the apparatus. When a cart is used, use caution
when moving the cart/apparatus combination to avoid injury from tip-over.
13.) Do not overload wall outlet. Use only power source as indicated.
14.) Use replacement parts as specified by the manufacturer.
15.) The product may be mounted to a wall only if recommended by the manufacturer.
16.) Upon completion of any service or repairs to this product, ask the service technician to perform
safety checks.
1
iC200_NCab050307.p65 3/5/2007, 11:291
……….For Your iPod
®
Thank you for purchasing this Digital Tuning Stereo Clock Radio with iPod® Docking
Station and SmartSet® Auto Time Setting System from Emerson Research. This
compact system has been designed with a powerful amplifier and matching high
fidelity speakers to produce the kind of sound that you would only expect from a
much larger, more expensive audio system. There is a built-in iPod® docking station
that allows you to play any dockable iPod® model* through the speakers of this
system. In addition while your iPod® is installed in the docking station the internal
iPod® battery will be recharged automatically. You can even choose to wake up to
your iPod® in the morning.
The digital tuner automatically scans the AM and FM bands and locks in stations
perfectly with no repetitive fine tuning required. And you can save 20 of your favorite
stations (10 AM and 10 FM) in the preset tuner memory for immediate recall at the
touch of a button.
Emerson’s patented SmartSet® Automatic Time Setting System automatically sets
the clock to the correct Year, Month, Date, Day, and Time the first time you connect
the system to your AC outlet, and after every power interruption. It even adjusts for
Daylight Saving Time changes and Leap Years automatically. The unique dual
alarm system allows you program one or both of the alarms for weekdays only,
weekends only, or everyday operation. And you can wake to your iPod®, to the
radio, or an electronic buzzer that starts softly and gradually increases in volume
to wake you gently.
The clock also includes a programmable 99-minute sleep to music timer with auto
shutoff and a 99-minute Nap timer that will wake you up after a nap without having
to change your regular alarm settings. Of course we also included a Snooze alarm
so you can catch a few extra winks after the alarm turns on in the morning, but this
is not your normal Snooze control. You can activate the Snooze by pressing the
Snooze button on the top cabinet or the remote control, or you can just wave your
hand in front of the “TOUCHLESS” SNOOZE SENSOR on the front panel.
The compact 13-key remote control lets you operate all the major functions of
your system from across the room. And we have even included a stereo headphone
jack and an Auxiliary Input Jack on the back panel so that you can also connect
older, non-docking iPods®, MP3 players, and personal CD players.
2
iC200_NCab050307.p65 3/5/2007, 11:292
We have taken great care to make sure that every component in your system was
in perfect working order when the system left our factory. If you experience any
problems with the set up or operation of this system please do not return it to the
retail store.
Please call the Emerson Consumer Products Customer Service Hotline, toll-free,
at 1-800-898-9020. One of our service technicians will try and help you resolve
your problem. If the problem cannot be resolved by phone you will be advised of
the proper procedure to obtain service or a replacement unit.
Once again thank you for purchasing this Emerson Research iPod® compatible
audio system.
(* works with any dockable iPod® introduced prior to January 2006)
®
iPod
is a trademark of Apple Computer Inc., registered in the U.S. and other countries.
iC200_NCab050307.p65 3/5/2007, 11:293
3
IMPORTANT NOTES
• Avoid installing this unit in places
exposed to direct sunlight or close to
heat radiating appliances such as
electric heaters, on top of other stereo
equipment that radiates too much
heat, places lacking ventilation or
dusty areas, places subject to
constant vibration and/or humid or
moist areas.
• Operate controls and switches as
described in the manual.
• Before turning on the power, make
certain that the AC power cord is
properly installed.
• When moving the set, be sure to first
disconnect the AC power cord.
FCC Information
This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to
provide reasonable protection agains t harmful interference in a residential
installation. This equipment generates, uses, and can radiate radio frequency energy
and, if not installed and used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which
the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including interference
that may cause undesired operation.
Changes or modifications not expressly approved by the party responsible for
compliance could void the user’s authority to operate the equipment.
4
iC200_NCab050307.p65 3/5/2007, 11:294
PREPARATION FOR USE
Unpacking and Set Up
• This carton contains the main unit, the remote control hand set, iPod® Support
Bracket and 5 different iPod® adapters so that you can securely connect any
dockable iPod® to the top mounted docking station. Remove all of the
components from the carton and remove all packing materials from the
components. We recommend that you save the carton and packing materials
if possible in the event that your system ever needs to be retuned for service.
Using the original carton and packing materials is the only way to protect you
unit from damage in transit.
• Remove any descriptive labels from the top or front panels of the main unit. Do
not remove any labels from the back or bottom panels.
• Place the main unit on a stable, level surface such as a table, desk, or shelf,
convenient to an AC outlet, out of direct sunlight, and away from sources of
water, moisture, heat, dust, dirt, vibration, or strong magnetic fields.
NOTE: The speakers in this system are not video shielded therefore it is
not recommended to place this unit on top of your TV set. The magnets in
the speakers could cause some color distortion in your TV picture.
• Unwind the AC power cord and extend it to its full length. This is important. The
FM antenna is built into the AC power cord and must be fully extended for best
FM reception.
Protect Your Furniture
This model is equipped with non-skid rubber ‘feet’ to prevent the product from
moving when you operate the controls. These ‘feet’ are made from non-migrating
rubber material specially formulated to avoid leaving any marks or stains on your
furniture. However certain types of oil based furniture polishes, wood preservatives,
or cleaning sprays may cause the rubber ‘feet’ to soften, and leave marks or a
rubber residue on the furniture. To prevent any damage to your furniture we strongly
recommend that you purchase small self-adhesive felt pads, available at hardware
stores and home improvement centers everywhere, and apply these pads to the
bottom of the rubber ‘feet’ before you place the product on fine wooden furniture.
5
iC200_NCab050307.p65 3/5/2007, 11:295
Battery Back-up System
AC Outlet
This unit includes a battery back up system powered by a built-in, long life CR2430
lithium battery. The battery maintains the time and alarm settings, the Sleep and
Nap timer settings, and the preset station tuner memories as well, whenever the
power is interrupted. If the power is lost the display will go off and the system will
not operate. However once the power is restored the clock will again reset itself
and all of your other settings will be correct.
The lithium battery that was installed in your system can supply back up memory
power for up to 5 years or even longer. The actual effective life of the lithium
battery will be affected by the length of time between the date the battery was
installed at our factory and the date that you connected your unit to your AC outlet,
and by the number and duration of the power outages that you experience in your
home. To maximize the life of the back up battery this system should be connected
to an AC outlet that is always ‘live’. Do not connect this system to an AC outlet
controlled by a wall switch.
When the lithium battery begins to weaken, the Low Battery indicator “ ” will
begin to flash in the display. When you see this flashing indicator you should replace
the lithium battery as soon as possible. Instructions for replacing the lithium battery
will be found at the end of this Owner’s Manual.
Power Source
This system is designed to operate on 120V AC 60Hz house current only.
Connecting this system to any other power source may cause damage to the
system and such damage is not covered by your warranty.
NOTE: The system has a polarized AC plug with one wide blade and one
narrow blade. The plug will only fit into matching polarized AC outlets.
This is a safety feature to reduce the possibility
of electric shock. If the plug will not fit in your
AC outlet, you probably have an outdated nonpolarized outlet. You should have your outdated
outlet changed by a qualified, licens ed
electrician. Do not file the wide blade on the
plug, or use an adapter to make the plug fit into
your outlet. This defeats the safety feature and
could expose you to electric shock.
6
iC200_NCab050307.p65 3/5/2007, 11:296
AC Plug
LOCATION OF CONTROLS AND INDICATORS
Front Panel
4
3
2
2
1
Top Panel
7
6
24
23
5
11
10
9
8
22
21
12
20
13
14
19
15
16
17
18
iC200_NCab050307.p65 3/5/2007, 11:297
7
Back Panel
25
Left Side Panel
29
28
27
26
30
iC200_NCab050307.p65 3/5/2007, 11:298
31
8
1.) TOUCHLESS SNOOZE SENSOR.
2.) Speakers.
3.) Multi-Function LED Display.
4.) iPod® Support Bracket.
5.) REMOTE SENSOR.
6.) Power “On/Off” Button.
7.) Preset / Buttons.
8.) Alarm 1 Button.
9.) Alarm 2 Button.
10.) Alarm Mode Button.
11.) iPod® Support Bracket Mounting Holes (Inside iPod® Sockets Compartment).
12.) iPod® Sockets Compartment Sliding Door.
13.) Play/pause Button.
14.) Function Button.
15.) Band Button.
16.) Volume +/– Buttons.
17.) Tuning/Skip (Clock/Time) / Buttons.
18.) Memory Button.
19.) Nap Button.
20.) Sleep Button.
21.) SNOOZE (Sleep/Nap Off) Button.
22.) Month/date Button.
23.) Time Button.
24.) Time Zone Button.
25.) 3-Volt Lithium Battery Compartment.
26.) AC Power Cord.
27.) Aux Input Jack.
28.) Phones Jack.
29.) Dimmer (High / Low) Selector Switch.
30.) Alarm 1 (Buzzer / Radio / iPod / Off) Selector Switch.
31.) Alarm 2 (Buzzer / Radio / iPod / Off) Selector Switch.
9
iC200_NCab050307.p65 3/5/2007, 11:299
LED Display
3
4
2
5
6
1
7
13 12 11 10 9 8
1.) MUTE Indicator.
2.) AM Indicator.
3.) Day Of Week Indicators.
4.) SLP (Sleep) Timer Indicator.
5.) NAP Timer Indicator.
6.) Time, Year, Month/date, Volume Level (00-63), Radio Frequencies Display.
7.) AL2 (Alarm 2) Indicator.
8.) Battery Low Indicator.
9.) FM ST. (FM Stereo) Indicator.
10.) TUNER Select Indicator.
11.) iPod Select Indicator.
12.) AUX Select Indicator.
13.) AL1 (Alarm 1) Indicator.
iC200_NCab050307.p65 3/5/2007, 11:2910
10
Remote Control
5
4
3
2
1
1.) Preset Button.
2.) Preset Button.
3.) Tuning/Skip Reverse Button.
4.) Power “On/Off” Button.
6
7
8
9
10
11
12
13
5.) Infrared Transmitter.
6.) Function Button.
7.) Volume + Button.
8.) Tuning/Skip Forward Button.
9.) Volume – Button.
10.) Band Button.
11.) Alarm Stop Button.
12.) Snooze Button.
13.) Battery Compartment (Back Cabinet).
iC200_NCab050307.p65 3/5/2007, 11:2911
11
Installing The Remote Control Batteries
The remote control requires two “AAA” batteries, not included. We recommend
that you use a well known brand of alkaline batteries for longest life and best
performance.
Open the remote control battery
compartment by sliding the battery
compartment cover in the direction of
the ‘arrow’.
Install two “AAA” batteries in the compartment according to the polarity markings
inside the compartment as shown in the illustration. If the batteries are installed
incorrectly the remote control will not work. After installing the batteries replace the
battery compartment cover.
NOTE: When the operation of the remote control becomes intermittent or stops
working completely replace the batteries as soon as possible. Never leave
weak or exhausted batteries in the remote for an extended period of time.
They may eventually leak and cause permanent damage to the remote control.
Battery Precautions
• Replacement of batteries must be done by an adult.
• Do not mix old and new batteries.
• Do not mix alkaline, s tandard (carbon-zinc) or rechargeable (nickel-cadmium)
batteries.
• The supply terminals are not to be short-circuited.
• Non-rechargeable batteries are not to be recharged.
• Exhausted batteries are to be removed.
• Only batteries of the equivalent type are to be used.
• Batteries are to be inserted with the correct polarity.
• Dispose of batteries properly. Do not dispose of batteries in fire. The batteries
may explode or leak.
12
iC200_NCab050307.p65 3/5/2007, 11:2912
OPERATING INSTRUCTIONS
• Make sure that you have extended the AC power cord to its full length.
The FM antenna is built into the power cord.
• Make sure that you have installed two fresh “AAA” alkaline batteries in
the remote control handset.
Setting The Time, The First Time
IMPORTANT: The firs t time you connect your new SmartSet® c lock radio to
the AC outlet the internal c omputer will automatically set the time correctly for
the Eastern Time Zone, which is the initial default setting. The display will
scan for a few seconds and then s how the correct Day and Time in the Eastern
zone. If you live in the Eastern Time zone, there’s nothing else to do. Your
clock is set correctly and running.
If you do not live in the Eastern Time zone you must change the default zone
display to your own zone. You only do this one time and the SmartSet® will remember
the new default zone setting and will always return to that setting after a power
interruption.
There are 7 time zones programmed into your SmartSet® clock radio as follows:
ZONE 1 — Atlantic Time
ZONE 2 — Eastern Time (Default Setting)
ZONE 3 — Central Time
ZONE 4 — Mountain Time
ZONE 5 — Pacific Time
ZONE 6 — Yukon Time
ZONE 7 — Hawaiian Time
To change the default time zone display, depress the Time Zone button.
The number “02” will appear on the display
indicating that the default zone is ZONE 2,
Eastern Time.
13
iC200_NCab050307.p65 3/5/2007, 11:2913
Hold the Time Zone button and then press either the Tuning/Skip (Clock/Time)
or buttons until your own time zone appears on the display, then release the
buttons.
The clock display will change to the correct time in the time zone you selected. The
clock will always return to the correct time in the zone you selected after every
power interruption. If you move to a different time zone, simply change the default
zone display to the new zone and the SmartSet® will remember that setting for you.
Date Display
To see the correct date at any time, depress the Month/date button. The display
changes from time to month and date (mm/dd).
For example, May 21st will appear as “5. 21”.
When you release the Month/date button the display returns to the correct time.
Year Display
To see the correct year, depress the Month/date and Time buttons together.
The display changes from time to year.
When you release the Month/date and Time buttons the display returns to the
correct time.
14
iC200_NCab050307.p65 3/5/2007, 11:2914
Loading...