Emerson E2 RX Series, E2 BX Series, E2 CX Series Quick Start Manual

Download

026-1621 Rev 0 12-JUN-2012

Quick Start Guide for E2 RX Refrigeration,

BX HVAC, and CX Convenience Store Controllers

Applicable to E2 firmware versions 4.0 and above

Retail Solutions

3240 Town Point Drive NW, Suite 100

Kennesaw, GA 30144, USA

Phone 770-425-2724

Fax 770-425-9319

FCC COMPLIANCE NOTICE

This device complies with Part 15 of the FCC lowing two conditions: (1) this device may not cause harmful interference, and (2) this device

must accept any interference received, including interference that may cause

undesired operation.

CE COMPLIANCE NOTICE

Class A Product Information for E2 Controllers: The Retail Solutions Einstein and E2 controllers are Class A products. In a domestic

envi

ronment this product may cause radio interference in which case the user may be

required to take adequate measures. This covers:

Rules. Operation is subject to the fol-

• All E2 family product types: RX - Refrig BX - Building/HVAC Controller (845-xxxx), CX- Convenience Store Con

troller (845-xxxx), and all version models: (300, 400, 500).

eration Controller (845-xxxx),

Table of Contents

1 QUICK START.............................................................................................................................................................. 1

1.1 L

OGGING ON ................................................................................................................................................................. 1

1.2 C

LEANING OUT THE CONTROLLER................................................................................................................................ 1

1.3 S

ETTING NUMBER OF NETWORK DEVICES.................................................................................................................... 2

1.4 S

ETTING NUMBER OF APPLICATIONS ............................................................................................................................ 3

2 SCREENS AND MENUS.............................................................................................................................................. 3

2.1 T

HE MAIN STATUS (HOME) SCREEN............................................................................................................................. 3

2.1.1 Customizing the Home Screen ............................................................................................................................... 3

2.2 C

OMMON SCREEN ELEMENTS ....................................................................................................................................... 4

2.2.1 The Header............................................................................................................................................................. 4

2.2.1.1 Header Icons ............................................................................................................................................................... 4

2.2.2 The Function Keys ................................................................................................................................................ 4

2.2.3 The Help Line......................................................................................................................................................... 4

2.3 S

CREEN TYPES............................................................................................................................................................... 5

2.3.1 The Main Menu...................................................................................................................................................... 5

2.3.2 Status Screens ........................................................................................................................................................ 5

2.3.3 The Actions Menu................................................................................................................................................... 6

2.3.4 The Setup Screens ...................................................... ..................................... ....................................................... 6

2.3.5 System Configuration Menu................................................................................................................................... 7

2.3.6 The System Information Menu ............................................................................................................................... 7

3 SETUP ............................................................................................................................................................................. 8

3.1 S

ET UP TIME/DATE ....................................................................................................................................................... 8

3.1.1 Setting the Time and Date...................................................................................................................................... 9

3.2 S

ET UP MODEM........................................................................................................................................................... 10

3.3 S

ET UP TCP/IP............................................................................................................................................................ 10

3.4 S

ET UP NETWORK BAUD RATES................................................................................................................................ 11

3.4.1 COM1 Serial (RS232) Baud Rate ........................................................................................................................ 11

3.4.2 I/O Network Baud Rate........................................................................................................................................ 12

3.5 S

ET UP USER ACCESS ................................................................................................................................................. 12

3.5.1 Changing Required User Access Levels .............................................................................................................. 13

3.5.2 Creating a New User Account ............................................................................................................................. 13

3.5.3 Deleting a User........................................................................... ......................................................................... 14

3.6 S

ET UP I/O NETWORK................................................................................................................................................. 14

3.6.1 Specify Number of Boards.................................................................................................................................... 14

3.6.2 Checking Online Status........................................................................................................................................ 15

3.7 S

ET UP ECHELON NETWORK....................................................................................................................................... 15

3.7.1 Specifying Number of Devices ............................................................................................................................. 15

3.7.2 Commissioning a Device...................................................................................................................................... 16

3.7.2.1 The Service Button Method...................................................................................................................................... 17

3.7.2.2 The Manual ID Entry Method................................................................................................................................... 18

3.8 LICENSE MANAGEMENT .............................................................................................................................................. 19

3.8.1 Web Services........................................................................................................................................................ 19

3.9 S

ET UP ALARMING...................................................................................................................................................... 20

3.9.1 Specifying Alarm Reporting Types....................................................................................................................... 20

3.9.1.1 The Display Line....................................................................................................................................................... 20

3.9.1.2 The Alarm Output..................................................................................................................................................... 20

3.9.1.3 Dial-Out .................................................................................................................................................................... 20

E2 RX/BX/CX Quick Start Manual Table of Contents • v

3.9.1.4 The Echelon Network (The Alarm Annunciator)..................................................................................................... 20

3.9.2 Setting up an E2 to be an Alarm Annunciator ..................................................................................................... 21

3.9.3 Alarm Dial-Out .................................................................................................................................................... 21

3.9.4 Introduction: Alarm Reporting............................................................................................................................. 22

3.10 S

ET UP GLOBAL DATA .............................................................................................................................................. 22

3.10.1 Priority Settings.................................................................................................................................................. 23

3.11 S

ET UP APPLICATIONS............................................................................................................................................... 24

3.11.1 Add/Delete an Application................................................................................................................................. 24

3.11.2 Using and Configuring a Setup Screen.............................................................................................................. 25

3.11.2.1 The Edit Menu ........................................................................................................................................................ 25

3.11.2.2 Entering Setpoints................................................................................................................................................... 25

3.11.2.3 Navigating the Setup Screen................................................................................................................................... 26

3.11.3 Using the Help Key to Get Property Help.......................................................................................................... 27

APPENDIX A: TROUBLESHOOTING................................................................................................................... A-1

vi • Table of Contents 026-1621 Rev 0 12-JUN-2012

1 Quick Start

This manual covers what to do when you are program-

ming an E2 for the first time.

The manual includes logging on, specifying information about I/O boards and application types, and other topics related to E2 programming and navigation. For more informat

1614.

1.1 Logging On

Figure 1-1 - User Login Dialog Box

screen displayed after initialization is the User Login screen.

ion, refer to the complete E2 Manual P/N 026-

When the E2 is powered up for the first time, the first

1. Enter “USER” in the Username field.

2. Press

3. Enter “PASS” in the Password field.

.

1.2 Cleaning Out the Controller

Cleaning out the E2 controller needs to be done if:

• If you are programming your E2 controller for the rst time.

• If all of the settings need to be cleared.

• If the program settings are unknown.

Open the E2 controller panel. There are two located midway down on the main board. These buttons are used to perform various hardw information about E2 hardware, refer to the E2 manual P/N 026-1614.)

•Reset Button - The button labeled “RESET” on the main board resets the controller. Pressing and holding this button for one second wi and retain all programmed applica-

tions, logs, and other data stored in memory.

• Clean

Clean outs are also commonly called Blue “R” resets,

ed for the key presses required to clean out Retail

nam Solutions’ previous generation of controllers, REFLECS.

Performing a Clean Out

Out Button - The button labeled CLEAN

OUT on the controller is used to perform a function called clean out. Using this button in conjunction with the Reset Button will cause a clean out, which is a reset that E2 will re-boot after a clean out with all programmed applications, logs, and other data erased.

erases all data from memory. The

are functions. (For more

ll cause the E2 to reset

buttons

4. Press

Logging into and out of the E2 controller can be done

at any time by pressing the you are currently logged out, pressing

the User Login dialog box. If you are already logged in, pressing

you to the E2 home screen.

Logging On Quick Start • 1

.

 key on the E2 keypad. If

 will bring up

 will immediately log you out and return

CAUTION: A clean out will erase all programmed parameters from memory. Do not

these instructions unless you are abso-

lutely sure you wish to remove all applications and logs

rom memory.

1. Press and RELEASE the Reset Button quickly. The screen will clear.

2. Press and Hold the C ton.

3.When “CLEANOUT” appears in lar

ge text across the screen,

RELEASE the Clean Out button.

lean Out but-

1.3 Setting Number of Network Devices

Figure 1-2 - Connected I/O Setup Screen

After logging in for the first time, the Connected I/O screen will ask you to specify how many of each type of device will be connected to the E2 you are currently programming. (Options will vary depending on the type of

roller used.)

cont

Unit Number (Echelon Subnet) Each E2 on the

Echelon This can be any number from 1 to 255, but each E2’ s number must be unique. No two E2s on the network may have the same unit number.

Enter this number in the Unit Number field. It is rec-

ommended you number the first E2 “1” and number the ot etc.).

Unit Name Type a name for the E2 in the Unit

Name field

Boards on the I/O Network

16AI Boards Enter the number of 16AIs or Multi-

Flex I/O boards on this E2’s I/O Network. If you have any special emulate 16AI, also include their total number of boards in this field.

8RO Boards Enter the number of 8ROs and Multi-

Flex 168AOs/168s/88AOs relay output boards on this

8DO Boards Enter the number of 8DO digital out-

put boards on this E2’s I/O Network.

4AO Boards Enter the number of 4AOs, MultiFlex

168 on this E2’s I/O Network.

IRLDS Controllers Enter the number of IRLDS/

Network must have a different unit number.

her E2s on the network sequentially (2, 3, 4,

MultiFlex or Gateway boards that

E2’s I/O Network.

AOs, and MultiFlex 88AO analog output boards

RLDS

leak detection units on this E2’s I/O Network.

Unit Controllers (Echelon)

Liquid Ctrls (CC100P/CC100LS) Enter the com-

bined number of pulse valve case controllers

C100Ps) and liquid-side stepper valve case con-

(C trollers (CC100LSs) in this field.

Suction Controllers (CC100H) Enter the num-

ber of suction stepper case controllers (CC100Hs) in

is field.

Circuit Suction (CS100) Enter the number of suc-

tion lineup circuit controllers (CS100s) in this field.

ESR8 Line Up Boards Enter the number of ESR

sucti

on lineup circuit boards (SR100s) in this field.

TD3 Temperature Displays Enter the number of

TD3 tem

EC-2 Case Controllers Enter the number of EC-2

refrigerated ca

Echelon 16AI Enter the number of 16AIe analog

Echelon 8RO Enter the number of 8ROe analog

perature display units in this field.

se controllers in this field.

put boards in this field.

NOTE: At any time, you can access this screen to add or remove boards on this E2 by pressing

.

When finished, press  (NEXT) to move to the

next screen.

2 • E2 RX/BX/CX I&O Manual 026-1621 Rev 0 12-JUN-2012

1.4 Setting Number of Applications

Figure 1-3 - Application Setup (RX version shown)

The Application Setup screen is where you will enter information about the types of devices on the E2’s control system. If you know how many applications will be needed, this step will save you time and will keep you from having to create new applications during the setup process. (Options will vary depending on the type of controller used.)

NOTE: You must create at least one application in this screen to continue to the next

creen, even if you are only using this E2 to

s control applications not listed on the screen. If necessary, you can create one application here and delete it

ter.

When finished, press  (NEXT) to go straight to

the Main Status (Home) screen.

2 Screens and Menus

2.1 The Main Status (Home) Screen

Figure 2-1 - Home Screen (RX version shown)

The Main Status screen is the “home” screen for the E2. When no one is logged in to the controller, this is the screen that will be shown in the display. When a user is logged into the controller, the Home screen is displayed when the user is not performing any actions such as application setup, viewing other status screens, etc.

The Home screen will vary depending on the configuration of the controller. In most cas will show the real-time status of the most fundamental systems being controlled by the E2.

The Home screen is a good place to point out three

portant common elements of all E2 screens: the screen

im header, the function key descriptions, and the help line.

Options will vary depending on the type of controller used. Fo including options for both RX and BX versions.

r more information on the E2 Home screen

es, the Home screen

2.1.1 Customizing the Home Screen

The Home screen can be customized to show different information depending on the user’s needs. There are eight different screen options available. The Device Summary screen is the Default screen. See Section 2.1.1, Customiz- ing the Home Screen for the steps to customize the Home screen.

Setting Number of Applications Screens and Menus • 3

2.2 Common Screen

HEADER

HELP LINE

FUNCTION KEY DESCRIPTIONS

Elements

Figure 2-2 - Common Screen Elements (RX version shown)

2.2.1 The Header

The first two lines at the top of the E2 screen are

referred to as the screen header. This area of the screen contains the time and date, controller name, subnet and node number, and alarm and failure notifications. In addition, it contains highlighted indicators and icons to show

a user is operating in a particular mode, such as full

when options, edit, macro record, or insert mode.

If the E2’s Global Data featur outside air temperature and outside relative humidity values, these values will also be

e is being used to supply

displayed in the header.

Icon Description

Wait, or system is busy Disk activity, or saving to disk Caps lock is ON

Table 2-1 - Header Icons and Descriptions

2.2.2 The Function Keys

Figure 2-4 - Home Screen Function Keys (RX version shown)

At the very bottom of every screen in the E2, there are five boxes labeled  through . These boxes are the function key descriptions. The function key descriptions show what each of the five pressed. (Options will vary depending on the type of controller being used.)

Function key usage often varies depending on which

or field E2 is currently in.

screen

function keys do when

2.2.3 The Help Line

The line directly above the function button menu is called the help line. The help line displays information about the currently selected field, such as general descriptions, possible ranges, and other information to help a user

aneuver around and/or configure the field.

2.2.1.1 Header Icons

At the very top of every screen in the E2, there are icons that indicate various stages of activity, number of users logged into the controller, battery alerts, connectivity status, and more.

Figure 2-3

Icon Description

Table 2-1 - Header Icons and Descriptions

- Header Icons

Single user is logged in Multi-users are logged in Terminal mode in use E2 is connected to Ethernet

TIP: To see different messages the help line generates, start from the RX Home screen.

ess  (CIRCUITS). Highlight a circuit

and press around the screen and notice how the help line

changes as the cursor moves from the setpoint to status sections. When finished, press the  key to return to the Home screen.

. Use the arrow buttons to move

4 • E2 RX/BX/CX I&O Manual 026-1621 Rev 0 12-JUN-2012

2.3 Screen Types

2.3.1 The Main Menu

Figure 2-5 - The Main Menu (RX version shown)

The Main Menu is accessed by pressing the  key. This menu gives you direct access to applications such as Suction Groups, Condensers, Circuits, Air Handling Units, Zones, Light Schedules, and Sensor Controls

ications, (depending on which controller type you are

appl using) as well as all configured applications in the controller. The Main Menu also allows you to add and delete

ications, gives system configuration abilities, and

appl shows status information for inputs and outputs, network, graphs and logs.

2.3.2 Status Screens

Each status screen is special concise at-a-glance view of how one or more systems are functioning.

TIP: To view the Suction Group Status screen in the RX controller, start from the Home

een. Press the function key  (SUC-

scr

TION GRP). If more than one Suction Group has been

et up, the Suction Group Summary screen opens.

s Choose which application you wish to view with the

cursor and press and HP rating for each compressor are displayed in

this screen.

To view other application types, use the function keys , , and  (see Table 2-2) to see the condenser, circuits, and sensor control status screens.

Key Function for RXFunction for BXFunction for

! Suction Group AHU AHU

@ Condensers Zones Lighting

# Standard and

Case Circuits

$ Sensor Control

and Power Monitor-

ing

% Setup Setup Setup

. The current status, runtime,

ly designed to provide a

Lighting Circuits

Sensors Sensors

Table 2-2 - S

Status screen functions are explained in more detail in

e Operator’s Guide to Using the E2 section of the E2

th manual, P/N 026-1614. For now, press

another important screen: the Actions menu.

Figure 2-6 - Status Screen (RX version shown)

Status screens are real-time views of application functions. They show the current statu rent values of all inputs, and other important data such as

rol setpoints, run times, and whether or not bypasses

cont or overrides are active.

Screen Types Screens and Menus • 5

s of all outputs, the cur-

tatus Screen Function Keys

 to access

2.3.3 The Actions Menu

Actions Menu

Item

Application Commands

Applications Logs/G

raphs

Table 2-3 - Actions Menu Options and Descriptions

Allows Service Start/End for Irrigation and Pulse Accumulation applications.

Opens various log and graph screens for Anti-sweat and Pulse Accumulation applications.

Opens the Circuit Report screen for

dard circuits only.

stan

Description

Figure 2-7 - The Actions Menu

The Actions Menu is available from any status screen

by pressing Enter any task in the E2 system software. This screen lists a

number of options that can be used to affect a selected field, an entire application, or the E2 in general.

Actions Menu

Item

Graph Opens graph view for the selected

Log Opens the Log screen

Override Opens the Override Update window

Expanded Information

Setup Opens the setup screen for the selected

Detailed Status Special status screen that shows

Manual Defrost For circuits only. Opens the Circuit

, and may be used to do just about

Description

val

ue.

of the selected

value.

where the s be overridden to a user-defined value or state.

Displays detailed information about the selected

val

ue.

det

ailed setpoints and input/output information with complete summary of inputs, outputs.

Bypass emergency defrost, or wash mode.

elected input or output can

value.

screen to force a manual or

One of the more important features of

Menu is the Setup screen screen will vary, depending on where the cursor is placed

in the Main Status (Home) screen before This is the easiest way to edit an existing application.

For more information on usage

how to implement its functions, see Operator’s Guide to Using the E2 section of the E2 manual, P/N 026-1614.

 (Setup). The actual setup

the Actions

 is pressed.

of the Setup screen and

2.3.4 The Setup Screens

Figure 2-8 - Typical Setup Screen

Setup screens are the interface used to change settings

and setpoints, and define inputs and outputs in the E2. Figure 2-8 shows a typical Setup screen and its primary elements. For more details on Setup screens, see Section

3.11.2.3,

Navigating the Setup Screen.

Table 2-3

6 • E2 RX/BX/CX I&O Manual 026-1621 Rev 0 12-JUN-2012

- Actions Menu Options and Descriptions

2.3.5 System Configuration Menu

Figure 2-9 - System Configuration Menu

The System Configuration Menu is one of the menus used to set up the E2. Included options are Input/Output Definitions, internal system information, remote communications, global data, alarm, logging, and network setup information.

To open the System Configuration menu:

1. Press

.

Menu Option Description

7 - Network Setup Opens the Network Setup menu,

where options to view network status, add or delete boards and controllers, commission devices, set up a router, and make board associations are available.

8 - Global Data Configure one or more analog

r digital sensors to be used as

o “global” values by all E2s.

9 - Licensing Opens the Licensing Report

age with a list of all licensed features on the current E2, and allows additional features, after a password key has been entered by the user, to be enabled.

Table 2-4

- System Configuration Menu Options

2.3.6 The System Information Menu

2. Press

The System Configuration menu contains nine menu

item

Menu Option Description

1 - Input Definitions View the status of all input

2 - Output Definitions View the status of all output

3 - System Information Menu that gives access to more

4 - Remote Communications

5 - Alarm Setup Set up dial-outs and alarm

6 - Logging Setup Enter information about Log-

Table 2-4

 (System Configuration).

boards

, as well as set up individ-

ual points on the I/O boards.

boards

, as well as set up individ-

ual points on the I/O boards.

E2 setup tion.

Gives access to modem information, dial-out setup, and TCP/IP

reportin

ging Group applications such as t

he sampling frequency and

total number of samples.

- System Configuration Menu Options

options and informa-

g for the current E2.

Figure 2-10 - System Information Menu

The System Information Menu is another menu used to set up the E2. The options in this menu allow setting up time and date, passwords, toggle full options, general information about the controller, and system administrator functions.

To open the System Information Menu:

1. Press

2. Press

3. Press

.

 (System Configuration).  (System Information).

Screen Types Screens and Menus • 7

The System Information menu contains nine items:

Menu Option Description

1 - General Controller In

2 - Time and Date Change the current date and

Edit general information about the E2, such as engineering units, and summer/winter change-over specifications.

time, and

specify date formats.

3Setup

3.1 Set Up Time/Date

3 - Passwords/User Access

4 - Firmware Revision Read-only information screen

5 - Service Actions Set up system diagnostics

6 - Note Pad Writable field for technician to

7 - Display Users Enter information about Log-

8 - Toggle Full Options When set to on, FULL wi

9 - Application Default

lue Setup

Set up usernames and passwords, and define security

requirements.

level

that contains current version information

(memory and execution and perform advanced functions (system resets and firmware update).

e notes about changes

mak made or general information.

ging Group applications such as the sam total number of samples.

appear at the top right of the screen and gives user full access to options and applications.

Choose the default values most appropriate to the refrigeration control components in the system.

pling frequency and

system

info),

Figure 3-1 - System Information Menu

The Time/Date Setup screen is where users may change the time, date, date format, Daylight Savings Dates, and special time synchronization features.

To get to the Time/Date Setup screen from the Main

1. Select

2. Select

3. Select

The Time/Date Setup screen (Figure 3-2) is where all time and date changes occur.

 (System Configuration).

 (System Information).

 (Time/Date).

Table 2-5 - System Information Menu Options

Figure 3-2

8 • E2 RX/BX/CX I&O Manual 026-1621 Rev 0 12-JUN-2012

- Time/Date Setup Screen (User-Defined Shown)

3.1.1 Setting the Time and Date

The Time Format field affects how times are displayed and entered throughout the controller. When 24 Hour Format is selected in this field, the hours are displayed and entered as a num is selected, the hours are displayed and entered as a number from 1 to 12; an A or a P at the end of the time signifies whether the time is A.M. or P.M.

T able 3-1 shows some times as how they would appear in both formats.

Time 12 Hour Format 24 Hour Format

7:15 a.m. 7:15:00A 7:15:00 12:00 noon 12:00:00P 12:00:00 11:59 p.m. 11:59:00P 23:59:00 12:00 midnight 12:00:00A 0:00:00

Table 3-1

To select a time format, sel using the  (LOOK UP) tab.

Active Date

The Active Date shows the current Julian date in the format that was chosen in the Date Format field. For security reasons, the Active Date cannot be in time than the current date without assistance from Retail Solutions Technical Service (1-800-829-2724).

Active Time

The Active Time is the current time in the controller’s internal clock. This time may be changed by entering the new time in the Active Time field.

When a new time is entered in the Active T is sent across the network and changed on all device clocks so that all devices can remain synchronized.

Time Zone

Time zone is where the time zone of the E2 is entered. Each time zone is represented by a time zone offset that corresponds to the amount each time zone must add or subtract from Greenwich Mean Time (GMT) to get the correct local time. Choose the time zone by using the  (LOOK UP) tab.

Time Server

Set this field to Yes or No depending on whether you would like to use SNTP (simple network time protocol) for synchronizing the E2 clock.

SNTP ensures accurate synchroniz second of computer clock times. If the E2 time is off by 5 seconds enabled. When the E2 time is updated, an entry in Service

or greater, the SNTP will update the E2 time if

ber from 0 to 23. When 12 Hour Format

- Time Formats (12 and 24 hour)

ect either 12 or 24 hour

set to a date earlier

ime field, it

ation to the milli-

Log is added.

If this field is set to No, the E2 clock will have to be set

anually. If this field is set to Yes, SNTP support is used. Two SNTP servers are supported: Primary Time Server, and an optional Secondary Time Server.

Primary Time Server

The E2 will call up this primary server first to synchronize the E2 time. If the primary serv secondary server is used.

Enter the IP address or name o should use to set the time (up to 40 characters).

Secondary Time Server

The E2 will use this secondary server if no response is received from the primary server, or if the primary server is invalid.

If desired, enter the IP address or name of the second server the E2 s ters).

Date Format

Dates may be presented and entered in either of two ways: month-day-year format, and day-month-year format. Choose the most appropriate date format by using the

(LOOK UP) tab.



Daylight Savings Dates

The Daylight Savings Dates type determines how the E2 will make date adjustments for daylight savings time. Use the  (LOOK UP) tab to cycle through the options in each of the fields. There are four options:

• ST

the standard United States’ method of determining Daylight savings time dates. The Daylight savings time will start on the Sunday of the second week of March ever y year, and will end on the Sunday of the first week of November (Note: these are the dates recently enacted by the U.S. Congress, which went into effect in 2007).

• USER DE

is chosen, the user can specify start and end times for daylight savings, including month, week, and day settings.

• EUROPEAN UNION DL pean Union Dayli dard US DLT Dates, with the exception that one ho during the last Sunday in March.

• DL ments to Active Time for Daylight Savings Time.

hould use to set the time (up to 40 charac-

ANDARD US DLT DATES - the E2 will use

FINED DL T DATES - when this option

ght rules are the same as the Stan-

ur must be added to the time at 1:00AM (GMT),

T Not Used - the E2 does not make any adjust-

er fails to respond, the

f the first server the E2

T DA TES - the Euro-

Set Up Time/Date Setup • 9

Daylight Savings Time uses GMT

This setting is only visible when Daylight Savings Dates is set to User Defined DLT Dates. If set to Yes, Daylight Savings Time uses GMT calculates the time to

change from GMT and the current time zone setting. For example, if the start time is at 1:00 AM, and the time zone is +200 GMT , the time change will occur at 3:00 AM local time. Defaults to No.

Unit Location From

Sunrise and sunset times are calculated based on either zip code or latitude/longitude. If US Zip Code is chosen in the Unit Location From field, enter the zip code in which the controller is located. If outside the United States, choose Lat/Long and enter the latitude and longitude values in which the controller is located. Once a value has been chosen, the controller and sunset times. The Sunset output will turn ON at sunset, and OFF at sunrise and can be conn circuit.

Sundown

Sundown is an output that calculates when the sun sets based on latitude and longitude, and is ON when the sun sets. The user will select the Board/Controller, Point/ Application, and Input values from the  (LOOK UP) menu for each field. (When a Lighting Schedule is configured to use Sundown information, the Lighting Schedule

ication automatically connects to the Sundown out-

appl put.)

is able to calculate the sunrise

ected to a lighting

3.2 Set Up Modem

3. Press

You can choose between an internal modem (one that is mo PC-104 slot in previous generation E2 circuit boards) or an external modem. If you have a modem, navigate to the COM3 Modem Port field and select Internal Modem. Press  (LOOK UP) for the Option List Selection screen.

 (Modem Setup) to advance to the Gen-

eral Services screen.

unted directly on to the E2 circuit board (via the

3.3 Set Up TCP/IP

Figure 3-4 - TCP/IP Addressing

The TCP/IP screen is where you enter the information

necessary to allow Ethernet connection to this controller. If this site uses Ethernet box-to-box, you will need to enter a TCP/IP address and a group name to allow all E2s on site to communicate as a group. See the E2 Ethernet Peer

Communications section of the E2 manual, P/N 026-

1614.

From the Main Menu:

1. Press

2. Press

3. Press

E2 units may be configured to

Ethernet computer network using TCP/IP protocol. To

Figure 3-3 - Modem Select Screen

From the Main Menu:

1. Press

2. Press

10 • E2 RX/BX/CX I&O Manual 026-1621 Rev 0 12-JUN-2012

 (System Configuration).  (Remote Communications).

enable Ethernet communication, you will need to enter IP address information for the E2 in the Serial IP screen.

IP Address The IP Address field sets the network

add PCs running UltraSite) will communicate with this E2 by sending information to this specified address. Contact your network administrator to determine

 (System Configuration).  (Remote Communications).  (TCP/IP Setup) to advance to the TCP/

IP Setup screen.

communicate across an

ress for this E2. Other network devices (such as

what IP address to enter. The IP Address always consists of four numbers

from zero to 255, each of which is separated by a period. Enter the address in this format.

Subnet Mask Contact your network administrator

to get

the correct subnet mask value, and enter it in

this field. The default value, “255.255.255.0”, is the subnet

commonly used for small networks.

mask

Primary DNS Contact your network administrator

to see

if a Primary DNS value is required for this E2. If so, enter the Primary DNS address supplied by your administrator in this field. If not, leave this field set to “0.0.0.0”.

Secondary DNS Contact your network administra-

tor to see if a Secondary DN this E2. If so, enter the Secondary DNS address supplied by your administrator in this field. If not, leave this field set

Primary Gateway Contact your network adminis-

trator to see if a Primary Gateway value is required fo

r this E2. If so, enter the Primary Gateway address supplied by your administrator in this field. If not, leave this field set to “0.0.0.0”.

Secondary Gateway Contact your network

inistrator to see if a Secondary Gateway value is

adm required for this E2. If so, enter the Secondary Gateway address supplied by your administrator in this field. If

DHCP Enabled Dynamic Host Communication

Prot

ocol (DHCP) is a protocol that assigns a dynamic IP address to devices on a network. With dynamic addressing, a device could have a different IP address every time it connects to the network. When set to Yes, DHCP Enabled keeps track of IP addresses and enables a new IP device to be added to a network without having to manually assign it a unique IP address. DHCP supports a mix of static and dynamic IP addresses.

to “0.0.0.0”.

not, leave this field set to “0.0.0.0”.

S value is required for

3.4 Set Up Network Baud Rates

NOTE: If a baud rate is changed in this screen, the controller must be rebooted (turned OFF then ON occur.

3.4.1 COM1 Serial (RS232) Baud Rate

To access COM1 Serial (RS232) and I/O Network

baud rates:

1. Press

2. Press

3. Press

4. Press

to the COM1 Baud rate field.

The COM1 Baud

communications between the E2 and an RS232 device (such as a satellite link or PC).

The baud rate selected in this field should correspond

th the baud rate for the RS232 device. For example, if

wi connecting a PC to this port, the PC’s COM port should be set up to communicate at the same rate as what is set in this field.

There are multiple options to choose from. Select one

the options below using  (LOOK UP) depending

of on the type of connection.

00 Baud (devices that operate at 1200)

• 12 00 Baud (devices that operate at 2400)

• 24

• 4800 Baud (devices that

• 9600 Baud (recom

• 19.2 Kbaud (reco

• 38.4 Kbaud (reco

again) to make the baud rate change

 to open the Main Menu.

 (System Configuration).  (System Information).  (General Controller Info) and navigate

rate field determines the speed of

operate at 4800)

mended for satellite) mmended for modem) mmended for modem)

• 57.6 Kbaud (reco

• 115.2 Kbaud (recommended for direct connect)

Set Up Network Baud Rates Setup • 11

mmended for modem)

3.5 Set Up User Access

Access the User Access Setup screen from the System

Information menu:

1. Press

 to open the Main Menu.

Figure 3-5 - COM1 Baud Rate Setup (Serial RS232)

3.4.2 I/O Network Baud Rate

The I/O Network baud rate is the rate at which the E2 will communicate with input and output boards on the RS485 I/O Network, and is located directly below the RS232 Baud rate field.

Press  to select the

baud rate is 9600 baud.

baud rate. The appropriate

2. Press

3. Press

Figure 3-7 - System Information Menu

In the User Access Setup screen, you may add user names and passwords to the controller with varying levels of security, and cus tomize user access for each security level.

 (System Configuration).  (System Information).

Figure 3-6

- I/O Network Baud Rate Setup

To access this menu, choose User Access) from the System Information Menu.

Figure 3-8

users. A user basically consists of a username, a password, and an access level. Whenever a username and password are entered during login, the E2 searches the user records

- User Access Setup Screen

An E2 may be programmed with up to 25 different

option  (Passwords/

12 • E2 RX/BX/CX I&O Manual 026-1621 Rev 0 12-JUN-2012

for the username and password. If found, the E2 will log the user in at the access level chosen for the user in the user records.

The access level determines how many of the E2’s fea-

tures the user may use. The E2 uses four access levels, one

g the lowest, and four being the highest. Ta ble 3-2

bein gives a description of each level and the capabilities they have access

to.

Each row has five columns, each of which corresponds

a different category of user actions.

• Setpoi

nt - This includes all actions that change

application setpoints. Also, alarms out of the Alarm Advisory Log is considered a “setpoint” action (refer to the Operator’s Guide to

Using the E2 section of the E2 manual (P/N 026-

1614) for the definition of “clearing alarms”).

clearing one or more

Level 1 Read-only access. Users may generally only

view

status screens, setpoints, and some

system settings.

Level 2 Setpoint and bypass access. Users may per-

form all the tasks a level 1 user may, plus

may change control setpoints and

they bypass some devices.

Level 3 Configuration and override access. Users

may

perform all the tasks a level 2 user may, plus they may override system settings, create new cells, and program new

ications.

appl

Level 4 System Administrator

tions are accessible by a level 4 user.

Table 3-2

- User Access Levels

access. All E2 func-

3.5.1 Changing Required User Access Levels

The Level Required For table in this screen is used to

customize what access level is required to perform certain actions within the E2 unit. There are four rows in this table, each of which corresponds to a different type of E2 function or application.

• Refrig

• Buildi

• Common Control

• Advanced Control - This category includes applica-

eration Control - This category includes

changes or actions involving refrigeration applications specific to RX controllers (Suction Groups, Condensers, Circuits, CC-10

ng Control - This category includes changes

or actions involving building control applications specific to BX controllers (AHUs, Zones, Lighting Control, Time Schedule, Demand Control, etc.).

- This category includes control

applications common to both RX and BX controllers (Sensor Control, Time Schedules, Conversion

s, Analog or Digital Combiners, Global Data,

Cell etc.).

tions common to both boxes that are only used by advanced users, lers, Refrigeration or HVAC Simulations, etc.

such as Loop/Sequence Control-

0s, etc.).

• Bypas

• Override - This in

• Config - This includes a

• Alar

For each row and column of the Level Required For

le, enter the desired minimum priority level that will be

tab required for users to perform actions on each type of application. E2 will check this table when action to verify the user has the appropriate access level to make the change. If the user’s access level is equal to or above the priority setting in the table, access will be allowed. If not, access will be denied.

s - This includes all actions that bypass a

device to a certain state, such as initiating a manual defrost, or configuring an application input designated as a “bypass.” Also, alarms in the Alarm Advisory Log is considered a “bypass” operation (refer to the Operator’s Guide

to Using the E2 section of the E2 manual (P/N 026-

1614) for the definition of “resetting alarms”).

cludes any user-ordered override

of a setpoint, input, or output.

application setting. This includes configuring inputs and outputs.

m Ack - This includes acknowledging one or

more alarms in the Alarm Log. If this field is set to 1, alarms can be acknowledged on the Alarm Advisory Log without a user logging into the controller

rst. If set to 2, 3, or 4, login is required before a

fi user can acknowledge alarms. The default is set to 3 (controller login required for acknowledging alarms). Refer to the Operator’s Guide to Using the E2 section of the E2 manual (P/N 026-1614) for the definition of “acknowledging alarms.”

resetting one or more

ll actions that change an

a user attempts an

3.5.2 Creating a New User Account

After entering the User Access Setup screen by press-

ing

 Passwords/User Access from the System Infor-

mation menu:

1. Move the cursor so that it is so

Users box at the bottom of the screen.

2. Press  (ADD USER) to put a the bottom of the list.

mewhere in the

blank record at

Set Up User Access Setup • 13

3. Type in the user name (Username), and then move to the next field (Password) by pressing the right arrow button.

4. Type in a password for the next user, then press the right arrow button to advance to the next field.

5. The Auto Logout feature mum time user may be inactive before being

ged out. Enter the amount of time for the user

log and press the right arrow button.

6. Enter the appropriate access level for the user. See Table 3-2.

7. Press  (BACK).

determines the maxi-

3.5.3 Deleting a User

To delete a user from the system:

1. Move the cursor so that it is highlighting the record

to delete in the Users box at the bottom of

the screen, and press  (DELETE USER).

2. A question box will appear to double check the delet

ion of the current record. Press

sure about the deletion.

 if you are

• Connected I/O Boards & Controllers

• Router Setup

• Controller Associations

For the total (E2) devices online or offline, status,

screens, changing board or controller names, config-

setup uring and commissioning devices, deleting viewing detailed status screens of controllers, select Net- work Summary.

For the number of I/O Network devices (16AIs,8ROs,

etc.) associated select Connected I/O Boards & Controllers.

To set up a router, select Router Setup. Fo information on routers and repeaters, refer to the Router and Repeater Installation Guide (P/N 026-1605).

For CC-100 circuit associations, select Contr Associations.

with each controller online and offline,

a device, and

r more

oller

3.6.1 Specify Number of Boards

Specify the number of boards from the Connected I/O screen:

1. Press

2. Press

 to open the Main Menu.

 (System Configuration).

3.6 Set Up I/O Network

Figure 3-9 - Network Setup Menu

To start the setup on the I/O Network, access the Net-

work Setup menu:

1. Press

2. Press

3. Press

The Network Setup menu displays four options:

• Network Summary

 to open the Main Menu.

 (System Configuration).  (Network Setup).

3. Press

4. Press

Figure 3-10 - Connected I/O Screen (RX version)

Boards on the I/O Network

16AI Boards Enter the number of 16AI analog

input boards on this E2’s I/O Network.

8RO Boards Enter the number of 8RO relay output

8DO Boards Enter the number of 8DO digital out-

 (Network Setup)  (Connected I/O Boards & Controllers)

ards on this E2’s I/O Network.

14 • E2 RX/BX/CX I&O Manual 026-1621 Rev 0 12-JUN-2012

put boards on this E2’s I/O Network.

4AO Boards Enter the number of 4AO analog out-

put boards on this E2’s I/O Network.

IRLDS Controllers Enter the number of leak detec-

tor units on this E2’s I/O Network.

(Options will vary depending on the type of controller

used.)

3.6.2 Checking Online Status

3.7 Set Up Echelon Network

3.7.1 Specifying Number of Devices

To specify the number of devices on the Echelon Net-

work, navigate to the Connected I/O screen:

1. Press

 to open the Main Menu.

Figure 3-11 - Network Summary Screen

You can check all boards that are on either the Echelon

Network (E2 controllers) or the I/O Network from the Network Status screen (See Figure 3-11). The Network Sum- mary screen displays information such as Node addresses for each board, and the status of Echelon and I/O boards.

To get to the Network Summary Screen:

1. Press

2. Press

3. Press

4. Press

From the Network Summary screen you can see the

al (E2) devices online or offline, status, setup screens,

tot change board or controller names, configure and commission devices, delete a device, and screens of controllers.

After determining if a board is offline, turn to Appen-

dix A: Troubleshooting.

 to open the Main Menu.

 (System Configuration).  (Network Setup).  (Network Summary).

view detailed status

the Subnet and

2. Press

3. Press

4. Press

Figure 3-12 - Connected I/O Screen (RX version shown)

ntroller used.)

Unit Number (Eche

Echelon Network must have a different unit number. This can be any number from 1 to 255, but each E2’s number must be unique. No two E2s on the network may have the same unit number.

Enter this number in the Unit Number field. It is rec-

ommended you number the first E2 “1” and number

e other E2s on the network sequentially (2, 3, 4,

th etc.).

Unit Name Type a name for the E2 in the Unit

Name field

Unit Controllers (Echelon)

Liquid Ctrls (CC100P/CC100LS) Enter the com-

bined number of pulse valve case controllers

 (System Configuration).  (Network Setup).  (Connected I/O Boards & Controllers).

lon Subnet) Each E2 on the

Set Up Echelon Network Setup • 15

(CC100Ps) and liquid-side stepper valve case controllers (CC100LSs) in this field.

Suction Controllers (CC100H) Enter the num-

ber of suction stepper case controllers (CC100Hs) in thi

s field.

Circuit Suction (CS100) Enter the number of suc-

tion lineup circuit controllers (CS100s) in this field.

ESR8 Line Up Boards Enter the number of ESR

suctio

n lineup circuit boards (SR100s) in this field.

TD3 Temperature Displays Enter the number of

TD3 tem

EC2- 29x Case Controllers Enter th e number of

EC2-29x refrigerated ca

EC2-39x Case Controllers Enter the number of

EC2-39x refrigerated ca

Echelon 16AI Enter the number of 16AIe analog

inp

Echelon 8RO Enter the number of 8ROe analog

inp

perature display units in this field.

se controllers in this field.

ut boards in this field.

Figure 3-13

NOTE: A device may only be commissioned if it is properly connected on the network and powered up.

- Network Summary Screen

3.7.2 Commissioning a Device

Once all records have been created and defined for all devices on the Echelon Network, they must be “commissioned.” Commissioning is necessary for the and establish communications with all devices on the network.

To start commissioning, open the Network Summary screen:

1. Press

2. Press

3. Press

4. Press

 to open the Main Menu.

 (System Configuration).  (Network Setup).  (Network Summary).

E2 to identify

How Echelon Commissioning Works

Each device that is capable of communicating on a

Echelon Network has a unique 12-digit “Neuron ID” code number that is hard-coded in a chip on the board. In order for the E2 to begin communications with a unit controller or another E2, it must know the device’s ID number.

When a device is commissioned, it either entered by hand into the E2 (via the front panel keyboard) or sent across the network to the E2 using the

ice’s service button. Once the E2 knows the device’s

dev 12-digit ID, it establishes communication and gives the device its user-defined subnet and node address. From that point on, the E2 uses only the subnet and node address to communicate with the device.

As mentioned above, there are two ways in which a

ice may be commissioned. No one way is better than

dev the other in terms of effectiveness, but one of the methods may be less difficult than the other depending on the type of installation.

MODBUS Commissioning

If commissioning a MODBUS device and multiple MODBUS ports are available, you will be prompted to select the appropriate network during the commissioning process.

s 12-digit code is

16 • E2 RX/BX/CX I&O Manual 026-1621 Rev 0 12-JUN-2012

3.7.2.1 The Service Button Method

To commission a device using the service button, you must first set up the E2 to receive a service button signal, and then press the service button on the device. When the signal is received by the E2, the device will be commissioned.

To set up the E2 to receive a service button signal,

ve the cursor to the Controller Name field of the record

mo you wish to set up, and press

Figure 3-14

A menu will appear on the screen, giving you the option of either pressing the service button, entering the Neuron ID by hand, or canceling and returning to the main

screen. Press

- Commissioning Menu

 to select the service button option.

 (SET ADDRESS).

CAUTION: When the E2’s Wait Time duration begins, the E2 will accept the first Neuron

ID code it receives. Be sure that no vice buttons on any devices on pressed during the Wait Time. Since the service button on the CC-100 is its Hand-held Terminal jack, be sure that no one has a Hand-held Terminal plugged into a CC-100 other than the one being commissioned.

The location of the service button and the method of

ng it depends on the device or controller being com-

pressi missioned.

The CC-100’s Service Button

Since the CC-100 is meant to remain in an enclosure, the CC100’s Hand-Held Terminal jack has been configured to act as the service but Terminal into the jack simulates a service button press.

The Hand-Held Terminal Jack is on the left side of the

controller next to the power cable harness connec-

case tion. To send the Neuron ID, plug a Hand-Held T erminal

the jack and hold it in for five seconds.

into

The TD3’s Service Button

the network are being

ton. Plugging a Hand-Held

other ser-

Figure 3-15

The E2 will prompt you to enter a wait time in the Wait Time field. The Wait Time is the amount of time the E2 will try to detect a service button press before declaring the attempt unsuccessful and returning to the main screen. To commission the device, the Neuron ID must be sent during the Wait Time duration.

After you enter a wait time in hours:minutes:seconds

rmat and press

fo All that is left to do is to press the service button on the

device to be commissioned.

Set Up Echelon Network Setup • 17

- Service Button Screen

, the Wait Time duration begins.

Figure 3-16

The service button on the TD3 is located on the front

panel (Figure 3-16). Of the two buttons on the face, the commissioning button is the one on the right. To send the Neuron onds.

- TD3 Service Button Location

ID, press and hold this button down for five sec-

The ESR8’s Service Button

(DISCONTINUED)

Figure 3-17 - ESR8 Service Button Location

The service button on the ESR8 is located on the right

hand side of the board directly below the termination jumper (Figure 3-17). To send the Neuron ID, press and hold this button down for five seconds.

Commissioning the EC-2

The EC-2 can be commissioned by pressing the UP ARROW key on the EC-2 front panel and holding it for five seconds.

3.7.2.2 The Manual ID Entry Method

The Manual ID Entry Method involves entering each device’s twelve-digit ID number by hand. When entered, the E2 searches the network and tries to match the ID number to the device. When the E2 finds this device, the commissioning process is completed.

The easiest way to set up a the Manual ID Entry Method is to arrange all network devices into a list that shows each device’s name, subnet and node address, controller type, and corresponding Neuron ID number. Once this list is complete, each device

ay be commissioned one at a time from the E2 front

m panel.

To make a list of network devices, follow the steps

belo

1. For each record set up in the Controller Network Con

figuration/Status Screen, write down the con-

tents of each device’s Controller Name, Model,

bnet, and Node fields on a sheet of paper. If

Su desired, you may also include the model or serial numbers of the units that will be controlled, as well as a physical location.

2. When step 1 is complete, go to where each device

list is installed and locate each device’s

on the Neuron ID sticker. Every Echelon-compatible device available from Retail Solutions has a sticker on its enclosure that shows the unit’s Neuron ID number. Each sticker also has a pe tag at the bottom that may be removed and

multiple-node store using

rforated

affixed to your form. Tear this tag of f and stick it in the Neuron ID blank on the sheet of paper. If the perforated tag has already been removed, write the ID number in the blank.

When all Neuron ID return to the E2 and enter the Neuron ID numbers for each device. To commission a device, move the cursor to the device to be commissioned and press  (Set Address).

Figure 3-18 - Commissioning Menu

A menu will appear on the screen, giving you the option of either pressing the service button, entering the Neuron ID by hand, or cancelling and returning to the

main screen. Press and bring up the dialog box shown in Figure 3-19.

Figure 3-19

Enter the device’s Neuron ID as it appears on the form you created, and press

the controller with the Neuron ID you entered. If it is found, the E2 commissions the device, and you may move on to commissioning the next device.

If E2 does not find it, the display will read “ERROR Co

ntroller with specified Neuron ID di d no t respond.” This could be caused by an improperly entered number, or it could be caused by a problem with the device’s network connections or power connections.

When all devices are commissioned, keep the form with the Neuron so that it may be referred to if necessary for board removals, replacements, or troubleshooting.

- Setting Controller Address - Neuron ID

ID stickers in an easily accessible place

numbers have been collected,

 to select the manual entry option

. The E2 will then look for

18 • E2 RX/BX/CX I&O Manual 026-1621 Rev 0 12-JUN-2012

3.8 License Management

Some applications in the E2 are only available when activated with a license key that is obtained through Retail Solutions. Licensing allows the user to activate certain features in the E2.

To obtain a license for a feature, go setup screen and obtain your E2 controller’s MAC

Address. Press

 + T, or from the Main Menu:

to the TCP/IP

Enter your license key to activate the desired feature:

1. Press

2. Press

3. Press

Figure 3-20

4. Call Retail Solutions Customer Service at 770-

Once you have received your unique license key from Customer ture(s) from the License Report screen. The License Report screen di firmware version, the list of all licensed features on that E2, the current number and maximum number of each of those applications allowed, and which additional features, (that require a license key), have been enabled.

From the Main Menu:

1. Press

2. Press

3. Press  (A

 (System Configuration).  (Remote Communications).  (TCP/IP Setup) to open the TCP/IP

Setup screen and locate your E2’s MAC address (circled in Figure 3-20):

- TCP/IP Screen - Locating the Mac Address

425-2724 and have your MAC Address ready in

order to obtain your unique license key.

Service, you can now activate the licensed fea-

splays that E2 controller’s unit type and

 (System Configuration).  (Licensing).

dd Feature).

Figure 3-21 - Enter Your Uni q ue License Key

4. Reboot the controller and open the License Report screen again to see the license key appear next to the activated feature (Figure 3-22):

Figure 3-22

- License Report Screen

3.8.1 Web Services

Web Services is a licensed feature that allows the user, once the required license has been obtained and entered, to view and adjust certain parameters in the E2 controller through a Web page. The E2 Web Services feature enables the user to:

• View site-specific information such site name, site one, local date and time.

• View the current version of the E2. This includes

e type of unit (e.g., RX-400) and the version of

th the firmware.

• View global data values such as outside air temper-

ature and humidity.

• View a list of other networked area controllers at

e site, including version and controller type infor-

th mation.

• Connect to the selected E2 for rem

ote configuration

License Management Setup • 19

changes.

• Access Terminal Mode.

• V iew Alarms.

To access Web Services: Open a browser window and enter the IP Address of

r E2 controller:

you

Figure 3-23

- E2 Web Services Page

3.9.1 Specifying Alarm Reporting Types

Apart from storing alarms it generates in its own Alarm Advisory Log, E2 can also report alarms it generates or receives in order to notify alarms in several different ways.

3.9.1.1 The Display Line

Alarms that occur within an E2 (or which are received by an Alarm Annunciator from another E2) may be reported to the header display at the top of the screen. When an alarm is reported to the display, the word “*ALARM*” flashes underneath the time at the top of the screen, allowing site managers or supervisors to see that one or more alarms are active for the E2.

Figure 3-25 - Display Line

3.9.1.2 The Alarm Output

Each E2 has a single digital output that reacts to alarm reports. An alarm can be reported to this output, in which case the output turns ON and remains on until the alarm condition has returned to normal.

personnel. E2 can report

3.9 Set Up Alarming

To set up alarms, open the Alarm Setup menu:

1. Press

2. Press

3. Press

Figure 3-24 - Alarm Setup Menu

 to open the Main Menu.

 (System Configuration).  (Alarm Setup).

3.9.1.3 Dial-Out

Alarms may be sent to remote alarm receivers via the modem defined for the controller. Possible dial-out devices include a PC running UltraSite, a printer, a fax machine, and a digital pager. Dial-out sites are configured in Section 3.9.3.

3.9.1.4 The Echelon Network (The Alarm Annunciator)

If multiple E2s exist on a network, you may choose to send alarms from all E2s across the Echelon Network so that they may be picked up by the Alarm Annunciator.

The Alarm Annunciator is the primary alarm reporting device in Annunciator gathers all alarms posted by all devices on the Echelon Network, records them in its own advisory log, and applies its own set of alarm filters to determine if the alarms should be dialed out, reported to its display, or sent to its Advisory Output.

ciator:

a multiple-device E2 Network. The Alarm

There are several benefits to having an Alarm Annun-

• An Alarm Annunciator makes it possible to handle all alarm dial-outs modem or network card.

for all controllers with a single

20 • E2 RX/BX/CX I&O Manual 026-1621 Rev 0 12-JUN-2012

• Users can view alarm notifications and alarm logs for all controllers from the Alarm Annunciator.

• Only the Alarm Annunciator needs to be programmed with alarm filter settings for dial-out, output, and display. All other controllers may be programm Master via the LonWorks Network.

ed to simply send all alarms to the Alarm

3.9.2 Setting up an E2 to be an Alarm Annunciator

Any E2 on the network that has a modem or Ethernet connection can be set up as an alarm annunciator, but only one alarm annunciator per network is allowed. To set up from the Main Menu:

3.9.3 Alarm Dial-Out

1. Press

2. Press

3. Press

4. Set Alarm An

If the target E2 is configured AnnuncIsHomesScrn property becomes available in General Services to select if the Annunciator log is to be the Home screen. The property will default to Yes. If the property is set to No, the Home screen will be either the default Home screen or the user-selected Home screen.

 (System Configuration).  (System Information).  (General Controller Info).

nunc field to Yes.

NOTE: When the E2 is set up as an Alarm Annunciator, the Home screen becomes the Alarm

Log.

as the Annunciator, the

Figure 3-27 - Alarm Setup Menu

One of the E2’s most important alarm reporting fea-

tures is its ability to dial-out to remote sites whenever a

ous alarm condition occurs. Each E2 is capable of dial-

seri ing out to up to three sites. The E2 may dial out to a computer, a fax machine, a digital pager, or a printer. To set up

the Main Menu:

from

Dial-out devices are set up in the Dial-out Setup

screen. T

o reach this screen:

1. Press

2. Press

3. Press

4. Press

(Main Menu).

 (System Configuration).  (Alarm Setup).  (Dial-out Setup).

Figure 3-26

Set Up Alarming Setup • 21

- Alarm Annunciator

Figure 3-28

This screen and the other screens that follow it are used to set up dial-out sites for both daytime and nighttime operation, including specifying phone numbers and IP

- Remote Dialout Setup Screen

addresses. Use the  and  keys to cycle through the Setup screens.

3.9.4 Introduction: Alarm Reporting

In general, a controller reports alarms to any or all of

four different sources:

1. The E2 Display Header

Alarms that occur within a E2 may be reported to the header display at the top of the screen. When an alarm is reported to the display, the word “*ALARM*” flashes underneath the time at the top of the screen, as shown in the example below:

3.10 Set Up Global Data

Figure 3-30 - System Configuration Menu

Figure 3-29

2. The Advisory Output

Each E2 has a single digital output that reacts to alarm reports. When an alarm is reported to this output, the output turns ON and remains on until the alarm condition has

eturned to normal.

3. Dial-Out

Alarms may be sent to remote alarm receivers via the modem defined for the controller. Possible dial-out devices include a PC running UltraSite, a printer, a fax machine, and a digital pager.

4. The LonWorks Network (The Alarm Annunciator)

If multiple E2s exist on a network, you may choose to send alarms across the LonWorks Network so that they may be picked up by the Alarm Annunciator.

Refer to Section 3.9.2 for information on how an Alarm Annunciator works.

- E2 RX Display Header

In a network with multiple E2s, it is often the case that certain sensors or transducer values will need to be used by all E2s. A good example of this is outside air temperature. There is no real need fo outside air temperature sensor, and therefore it would be beneficial if a single sensor could be used by all E2s on the network.

Figure 3-31

Navigate to the Global Data screen from the Main Menu:

- Global Data Setup Screen

r every E2 to have its own

1. Press

2. Press

3. Press  (Setup) to

The Global Data feature is an enhanced effectively distributing commonly used input values between multiple E2s. Sensors such as outdoor temperature and outdoor humidity are set up on an E2 as Global

a inputs. This E2 then becomes the “provider” of the

Dat

22 • E2 RX/BX/CX I&O Manual 026-1621 Rev 0 12-JUN-2012

 (System Configuration)  (Global Data) to open the Global Data

Status screen.

open the Global Data

Setup screen.

method of

global sensor values to all other Global Data applications

PRIMARY

SECONDARY

PRIMARY USED AS GLOBAL

OUTSIDE AIR TEMP BY ALL E2s

SECONDARY SENSOR USED AS OUTSIDE

AIR TEMP WHEN PRIMARY FAILS

26512038

on the E2.

tion in any E2 on the network.

assu tions. When you create new applications in the E2, it will always inputs (except for the spares) to their corresponding Global Data outputs.

3.10.1 Priority Settings

there are four settings to choose from.

As a result, a single sensor can be used by any applica-

Unless you program it otherwise, the E2 always

mes you will be using Global Data in all your applica-

automatically connect the appropriate application

When selecting the priority for a global sensor input,

Primary Primary inputs are the hig

hest priority inputs. If a sensor is set up with a primary priority, it is recognized by all Global Data applications on the network as the highest priority. The primary provider sends this input value to the other Global Data applications in the other E2s, and

each E2 immediately sends that value to all of its own applications that use the Global Data input.

Only one input of each type may be designated as a

primary o

n the E2 Network. In other words, if one E2 is acting as the primary provider of the global Outdoor Air Temp, no other E2 on the network may have

lobal Outdoor Air Temp sensor with a “primary”

a g priority.

If using this priority setting, you must enter board and

nt settings.

poi

Secondary Sensors that are set up with secondary

prioriti

es are backup sensors that will be used by all

Global Data applications if the primary sensor fails.

If a global input is set up on an E2 with a secondary

, the E2 will not send its value to the other

priority Global Data applications as long as it is receiving a primary value of that type from another E2 on the network. If a secondary provider does not receive a primary value update at least once every five minutes, the secondary provider will assume the primary sensor has fai

led, and it will send the secondary value to all other Global Data applications on the network. These applications will then use the secondary value in

place of the failed primary value.

Secondary providers will continue to send the input

valu

e until the primary provider again sends a valid update to the other Global Data applications. The secondary provider would then stop sending the secondary value, and all Global Data applications would use the pri

mary value.

If using this priority setting, you must enter board and

int settings.

Example: Ou

t of three E2s, an outside air temperature sensor on E2 A’s I/O Network is set up as the primary provider of the global Outside Air Temp input. A similar sensor is set up on E2 C with a secondary priority (see Figure 3-32).

As long as E2 A is capable of broadcasting a valid

perature value, all three E2s would use E2 A’s

tem Outside Air Temperature value in their own Global Data applications.

However, if E2 A loses contact with the sensor , E2 A no

nger has a valid temperature value to send to the

lo other Global Data applications. After five minutes of no updates from E2 A, E2 C will consider the primary Outside Air Temp source to have failed, and it

l begin sending the value of the secondary sensor

wil to the Global Data applications of the other two E2s. All E2s would then use this secondary value as Outside Air Temperature.

Figure 3-32

- Global Data Priority Example

Just as there may be only one primary provider for

each input type, there may be only one secondary for each input type. It is recommended that secondaries be set up on different E2s than primaries; this way, if a single controller fails or loses communication with the other E2s, there will still be a usable input source for the other E2s.

Set Up Global Data Setup • 23

User This setting means the E2’s global data will

read (or be a “User” of) all values coming from the network. This setting is for E2s that are not con nected to the sensor itself, but read the data that comes from it.

If the application in this E2 will be using primary or

secondary inputs from other E2s, then set the priority to “USER.”

Local Only This setting specifies that the input to

the global data is read and sent only to within the E2 you are programming. Also, this means that this E2 will not read any Primary or Secondary providers from the network.

If using this priority setting, you must enter board and

point settings.

Example: Setting Up an Outdoor Temperature Sensor

1. Press  (Global Data) and the Status screen

opens.

2. Move the cursor to the Outdoor Air Temperature (OAT) Mode, and then choose the priority by

scrolling with the

3. Press the down arrow button once to the Board and Point section and enter the board and point locations for the sensor.

4. Press  (BACK) to return to the Main Status (Home) screen.

The Outdoor Air T emperature sensor is now set up as a global device in the E2. Other global inputs can be set up using the same method as above.

E2 is now ready to be programmed with applications.

, keys.

3.11 Set Up Applications

3.11.1 Add/Delete an Application

Add an Application:

1. Press the  key to open the Main Menu screen.

2. Select  (Add/Delete Application) to open the Add/Delete Application menu.

3. Select  to add an application.

4. Choose an application by pressing  (LOOK UP) to open the Option List Selection menu, and choose the application you wish to add.

5. Press  to place the application in the Type field.

6. Select the number of applications you wish to add in the How many? field.

7. Press  to add.

8. You are then asked if you would like to edit the application now. Press Y (Yes) or N (No).

Delete an Application:

1. Press the  key to open the Main Menu screen.

2. Select  (Add/Delete Application) to open the Add/Delete Application menu.

3. Select  (Delete Application).

4. Press  to delete the application if not dis-

played by default.

5. If not displayed by default, choose the application you wish to delete by selecting  (LOOK UP). The Option List Selection menu opens. Choose the application you wish to delete from this list.

From the Main Status (Home) screen, place the cursor

on the application you wish to view and press  (SETUP). You can also press

from the Actions Menu to open the Setup screen for your selected application.

24 • E2 RX/BX/CX I&O Manual 026-1621 Rev 0 12-JUN-2012

 and select  (Setup)

6. Press  and the application appears in the Type field.

7. Press  to delete the application.

8. A dialog box opens asking if you are sure you want to delete the application you have selected. Press Y (Yes) or N (No).

3.11.2 Using and Configuring a Setup Screen

The Setup screen is application-specific depending on

where you place the cursor on the Home screen.

Press

 to open the Actions Menu and select 

(Setup), or press  (SETUP) on the Home screen.

The Setup screen for your selected application will

open

3.11.2.1 The Edit Menu

ames and board numbers.

• Setup I/O - allows user to enter an input or output

int setup screen.

3.11.2.2 Entering Setpoints

An application setpoint is a user-defined control parameter stored inside the controller. Setpoints can be programmed from any application setup screen.

To enter setpoints from a Setup screen:

1. Press  tion’s Status screen. (If starting from the Home screen, mo

tion’s value and press Menu. Choose Setup. This will take you to the

Setup screen.)

2. Once inside the application’s Setup screen, look fo

r the Setpoints option in the index tabs along

the top of the screen.

3. Use  points box of your application will open.

(SETUP) from the desired applica-

ve the cursor to the desired applica-

 to open the Actions

(NEXT TAB ) to tab ov er and th e Set-

Figure 3-33 - Edit Menu

The Edit menu becomes available when you are on a Setup screen and can be opened by pressing  (EDIT). Depending on which Setup option (index tabs) is highlighted, the Edit menu allows you ting using these options:

• Alternate I/O Formats - setting up pointers can change Value, or Area Ctrl:Application:Property.

• Set Multiple Outputs - all output pointer to multiple input pointers.

• Output Change Delta - the +/- change occur at the output before the new value is used.

• Generic Alarm Setup - enables the user to customassi

• Logging Setup - enables the user to turn logging on fo next to the parameter, default logging has already been enabled for the Logging Group Cell.

• Bypass Setup - Opens screen for bypass input types and remain active for a “Bypass Duration”. For example, Time Schedules have two such inputs.

• I/O Mode - toggles between displaying board

a field to expect a Board:Point, Fixed

gn alarming parameters in the controller.

r a particular parameter. Note that if “L” appears

, which are “Momentary” or “Level” triggered

to change field format-

ows you to connect an

that must

Figure 3-34 - Setpoints Box

Set Up Applications Setup • 25

3.11.2.3 Navigating the Setup Screen

Figure 3-35 - Typical Setup Screen (RX version shown)

The Setup utility is the interface used to change set-

tings and setpoints, and define inputs and outputs in the E2. Figure 2-8 and Figure 3-35 show a typical Setup screen and its primary elements.

Index Tabs

The ten boxes at the top of the screen labeled C1

through C0 are known as the index tabs. These tabs provide a short index of the screens current application. The numbers C1 through C0 represent the screen numbers (C1 being screen 1, C2 being screen 2, and so on).

Each of the Setup screens that you may access will

have a name besid Figure 3-35 for example, you will notice some tabs have names, while others are blank.

As you move through these screens within the Setup

r, the highlight will move to different tabs to indicate

Edito which screen is being displayed.

• Pressing  (PREV of the screens.

• Pressing  (H to the Main Status (Home) screen.

e its number. But as in Figure 2-8 and

that are used to set up the

TAB) will back-up the order

OME) at any point will take you

TIP: To see each screen in a typical setup for the E2 RX controller, start from the Main Status (Home) screen.

1. Po

sition the cursor somewhere inside the Suc-

tion Groups section and press (Setup), or just  (SETUP) from the Home

screen. The General Setup screen will be displayed.

2. Press  to Setpoints. The Setpoints Setup screen is displayed.

3. Press  comes up.

4. Press  the Setup menu screens. When the C0 tab (MORE) is highlighted, there may be more

than one extra Setup screen. Press (zero) to see a list of all Setup screens for that

application.

5. Keep pres extra screens until C1 is highlighted once more.

These screens (C1 th

information that is associated with the selected suction group.

Blank tabs are inaccessible. There are several why a tab may be inaccessible (i.e., without a name next to the number):

• The tab (and the corresponding screen) is unused reserved for later revisions.

and

• The screen may only be accessed when running in Options mode.

Full

• The screen may require one or more fields to be set

certain values before the screen may be accessed.

to For example, a screen containing nothing but compressor proof input definitions might be hidden if there is tem there are no proof checking devices group’s compressors. To access this screen, you would have to set this field to “YES”.

The screen you are cu

in the screen’s index tab. For example, in Figure 2-8 and Figure 3-35, because Screen 1 is displayed, tab C1 is highlighted.

a field on another screen that tells the sys-

(NEXT TAB) to move the cursor

again and the Inputs Setup screen

a few more times to see the rest of

sing  while taking note of the

rough C0) contain all of the set up

rrently in is always highlighted

 and 

 + 

reasons

on the

26 • E2 RX/BX/CX I&O Manual 026-1621 Rev 0 12-JUN-2012

The Help Line

The line near the bottom of the screen above the func-

tion key menu is the help line. The vides a short description of the selected field, along with

portant information such as minimum and maximum

im value ranges, and setup instructions.

The Function Keys For Setup

The five boxes at the very bottom of the screen show the function of keys  through . Most of these keys retain the same function no matter which field, screen, or application is selected in a Setup screen. Table 3-3 shows what each key is used for.

Key Function Description

! PREV TAB Moves backward one

@ NEXT TAB Moves forward one

# EDIT Opens the Edit Menu

$ STATUS, OVER-

RIDE, or LOOKUP

% CANCEL Cancels the operation

help line this time pro-

screen

Opens the Detailed Status screen, Opens the O

verride Update screen, or Look Up Tables

Table 3-3 -

After all of the functions of E2 are is to set the System Configuration, which is basically how the system is used.

Function Keys for Setup Screens

set up, the next step

3.11.3 Using the Help Key to Get Property Help

Property Help gives an explanation of the parameter, input, or output the user has selected.

Pressing the parameter, input, or output opens the Property Help window. The Property Help window displays documentation specific t rently pointing to.

 key while the cursor is pointing to a

o the parameter, input, or output the cursor is cur-

Set Up Applications Setup • 27

Appendix A: Troubleshooting

The chart below describes symptoms and solutions if troubleshooting the system or equipment is needed. For further information, contact Retail Solutions Service at 1-800-829-2724.

SYMPTOM POSSIBLE PROBLEM SOLUTION

I/O Network Problems I/O board not getting power. Check I/O board power--is the green STATUS light

on? If not, check power wiring connections, and use a multimeter to verify the board is getting 24VAC. Reset power to board.

I/O board not communicating or won’t come online.

Dip switches are set incorrectly . Check I/O board network dip switches. Verify net-

T erminating resistance jumpers are set incorrectly.

Boards are not powered. Check Network/Power voltages.

Echelon Network Problems Faulty wiring. Check connections. Are wires broken or loose?

Termination jumpers are set incorrectly.

Subnet (unit #) is set incorrectly.

Check I/O network connections:

1. Check wire polarity (positive to positive/negative to negative)

2. Check for broken or loose wires.

work ID number is not a duplicate and that baud rate switches are set to 9600. (If switches are wrong, make changes and then reset the controller.)

Check for proper setting of terminating resistance jumpers. Network segment should be terminated on the two endpoints of the daisy chain and untermi nated everywhere else.

Check network polarity (positive to positive/nega tive to negative). Check for wire damage.

Check for proper setting of terminating resistance jumpers. Network segment should be terminated on the two endpoints of the daisy chain and untermi nated everywhere else.

Each controller must have its own subnet address.

Appendix A: Troubleshooting • 1

SYMPTOM POSSIBLE PROBLEM SOLUTION

Compressor will not Operate Compressor is not programmed

properly.

Compressor types are set up incorrectly.

Compressor programmed with incorrect rating.

Pressure setpoints are set up incorrectly.

Board and point addresses are incorrect.

Verify that E2 was programmed for correct number of compressor stages. Highlight the General tab (C1) in the Suction Group Setup screen. Is the cor rect number of stages in the “Number of Stages” field?

Make sure that compressor stages were properly set up as VS (variable speed), C (compressor), or U (unloader).

Verify that compressors were assigned the proper rating (HP/AMP, or BTU).

Set proper pressure setpoints. If you are controlling the rack using suction pressure, enter the pressure setpoint in the SUC PRES SETPT field. If you are controlling by temperature, enter the temperature setpoint in the CTRL TEMP SETPT field. Note: Pressure setpoints are located under the Setpoints tab (C2) in the Suction Group Setup screen.

Set proper board and point settings for input, output, and compressor outputs. Board and point settings are located under the Inputs tab (C4), Outputs tab (C5), and Comp Outs tab (C7) in the Suction Group Setup screen.

2 • E2 RX/BX/CX I&O Manual 026-1621 Rev 0 12-JUN-2012

SYMPTOM POSSIBLE PROBLEM SOLUTION

Compressor will not Operate (Cont.)

8RO fail-safes are not wired correctly.

Verify fail-safe wiring on 8RO board for N.O./N.C. positions. One wire of the two-wire connection should always be connected to the middle terminal. The second wire must be either connected to the N.C. terminal (if you want the relay to be closed (ON) during power failure) or the N.O. terminal (if you want the relay to be open (OFF) during power failure.)

Compressor in override. Highlight compressor stage and cancel the override

by pressing Enter to open the Actions Menu. Select 3 for Override options, or go to the Override/ Bypass Log to view and cancel overrides:

1. From the Main Menu, press 8 to open the Status menu.

2. From the Status menu, press 4 for the Gr aphs/ Logs menu.

3. Press 3 for the Override/Bypass Log. (This screen gives you quick access to all overrides/ bypasses in the system)

Rack is in Phase Fail. Verify correct phase and verify correct input for

phase loss. If you specified that phase protection would be used on this rack, the Phase Loss input is displayed. The Phase Loss input is automatically configured to use E2’s Global Data phase loss protection source. If you wish to define a different source, redefine this input definition. To point this input to a board and point address: press  (EDIT) and then 1 to change the definition format.

Oil sensors are set up but are not in use.

Remove oil sensors from individual compressors.

1. Highlight the Comp Setup tab (C6) in the Suction Group Setup screen.

2. Use the arrow keys to select the OIL SENSOR field.

3. Choose “None” from the LOOK UP menu.

Appendix A: Troubleshooting • 3

SYMPTOM POSSIBLE PROBLEM SOLUTION

Problems with Condenser Condenser will not operate. Verify that E2 is programmed with proper number

of fans.

1. Highlight the General tab (C1) in the Condenser Setup screen.

2. Is the correct number of fans in the Number of Fans field?

Incorrect board and point settings.

Confirm proper board and point settings: Go to the Inputs tab (C3) in the Condenser Setup screen to check PRES CRTL IN and DISCH TRIP IN.

Fail-Safe wiring on 8RO is incorrect.

Verify proper fail-safe switch positions on the 8RO board. The fail-safe dip switches are labeled S2 on the 8RO and S3 on the 8ROe and 8IO. Set the rocker UP (ON) to close the relay and turn the out put ON during network failure. Set the switch DOWN (OFF) to open the relay and turn the output OFF during network failure.

Condenser will not split. Enable the con denser to split.

Go to the General tab (C1) in the Condensers Setup screen and set the Split Enable field to Yes.

Unsplit setpoint is set too low. Unsplit setpoint value is compared with discharge

pressure value instead of temperature. Enter the value in terms of discharge pressure. Go to the Setpoints tab (C2) in the Condensers Setup screen and check that the UNSPLIT STPT field value has been entered as a pressure value.

Half of the fans are not running.

Check the split fan relay output:

1. Go to the Other Outs tab (C7) in the Condensers Setup screen and check that SPLIT FAN has a board and point assignment.

2. Verify Split is enabled: Go to General tab (C1) in the Condensers Setup screen and set the Split Enable field to Yes.

3. Verify output is ON.

Problems with Cases Case will not go into hot gas or

cool gas defrost.

Check Group LLSV in Suction Group setup:

1. Go to the Outputs tab (C5) on the Suction Groups Setup screen and check GROUP LLSV.

2. Verify that the case(s) is assigned to the correct group.

Case will not terminate out of defrost mode.

1. Verify the termination type (Term Type) in the Defrost tab (C4) in the Standard Circuits Setup screen.

2. Check the defrost termination input location on circuit input.

3. Go to the Inputs tab (C6) and check DEFROST AV TERM.

4 • E2 RX/BX/CX I&O Manual 026-1621 Rev 0 12-JUN-2012

SYMPTOM POSSIBLE PROBLEM SOLUTION

Problems with Global Actions

Problems with Temp Sensor or Pressure Transducer Dis playing Proper Value

Information cannot be read from another E2 controller.

Verify that the controller with the sensor is set up as the Primary and the controller receiving the infor mation is set up as the User (both controllers default as local).

16AI input dip switches are set improperly.

The 16 dip switches on the 16AI board correspond to each of the inputs: Dip Switches Up = Temperature Sensor Dip Switches Down = Pressure Transducer

Incorrect board and point address.

Set proper board and point settings for both input and output: Go to the Inputs tab in the application’s Setup screen and check Board and Point.

Incorrect sensor type. 1. Verify that the sensor type in E2 is the same as

the sensor installed. (For example, “5V-200PSI” is a 5-volt powered 200PSI pressure transducer, and “T emperature” is the standard Retail Solutions tem perature sensor.

NOTE: The previous Eclipse and Standard sensors are now 5V and 12V respectively.

2. From the Main Menu, select System Configuration (7) and Input Definitions (1).

3. Highlight the desired input and press  (SETUP) to check Sensor Type.

No Heat or Air Will Come OnIncorrect board and points

assignment. Check the Heat and Cool OAT

lockout temps.

Dehumidification Problems Number of stages are not set up

or set up incorrectly.

Dehumidifier source not set up. From the same screen, verify what the sensor

Temperature setting for DEHUM OCC or DEHUM UOC is set too high.

Make sure that your board and points are assigned to the correct compressors and heat stages

From the Home screen, press  (AHU),  (SETUP). Move cursor to C5 (HT/CL Setup) to check the Lockout temperatures.

From the Home screen, press  (AHU),  (SETUP). Move cursor to C9 (Dehum) to check Dehum Stages.

source is. From the same screen, check the minimum temper-

ature setting.

Appendix A: Troubleshooting • 5

SYMPTOM POSSIBLE PROBLEM SOLUTION

Lighting Control Problems Lights will not come on. Make sure you have a Time Schedule set up. A

Time Schedule is not Lighting Control. Y ou can use the same Time Schedule for several Lighting Con trols. Set up the Time Schedule first and then assign it to a Lighting Control.

Set up a Time Schedule and got to Lighting Control. Choose the desired application and press  (SETUP). Move the cursor to C7 (Inputs) and high light the Board field. Press  (LOOK UP),

choose the input device and press the Point field and press  (LOOK UP). Select the type of schedule and press

Make sure Lighting Control output is assigned.

. Highlight

.

Lights Will Not Come On With The Photocell

Photocell is not recognized by controller.

Make sure the photocell is configured as an analog input.

Verify that the type of light sensor is correct. If using a light level sensor from another E2 con-

troller, set it up on the controller it is associated with in the Global Data section.

6 • E2 RX/BX/CX I&O Manual 026-1621 Rev 0 12-JUN-2012

The contents of this publication are presented for informational purposes only and they are not to be construed as warranties or guarantees, express or implied, regarding the

products or services described herein or their use or applicability. Emerson Climate Technologies Retail Solutions, Inc. and/or its affiliates (collectively “Emerson”), reserves

the right to modify the designs or specifications of such products at any time without notice. Emerson does not assume responsibility for the selection, use or maintenance of

any product. Responsibility for proper selection, use and maintenance of any product remains solely with the purchaser and end-user.

Emerson E2 RX Series, E2 BX Series, E2 CX Series Quick Start Manual

Specifications and Main Features

Frequently Asked Questions

User Manual

1 Quick Start

1.1 Logging On

1.2 Cleaning Out the Controller

1.3 Setting Number of Network Devices

1.4 Setting Number of Applications

2 Screens and Menus

2.1 The Main Status (Home) Screen

2.1.1 Customizing the Home Screen

2.2.1 The Header

2.2.2 The Function Keys

2.2.3 The Help Line

2.2.1.1 Header Icons

2.3 Screen Types

2.3.1 The Main Menu

2.3.2 Status Screens

2.3.3 The Actions Menu

2.3.4 The Setup Screens

2.3.5 System Configuration Menu

2.3.6 The System Information Menu

3Setup

3.1 Set Up Time/Date

3.1.1 Setting the Time and Date

3.2 Set Up Modem

3.3 Set Up TCP/IP

3.4 Set Up Network Baud Rates

3.4.1 COM1 Serial (RS232) Baud Rate

3.5 Set Up User Access

3.4.2 I/O Network Baud Rate

3.5.1 Changing Required User Access Levels

3.5.2 Creating a New User Account

3.5.3 Deleting a User

3.6.1 Specify Number of Boards

3.6 Set Up I/O Network

3.6.2 Checking Online Status

3.7 Set Up Echelon Network

3.7.1 Specifying Number of Devices

3.7.2 Commissioning a Device

3.7.2.1 The Service Button Method

3.7.2.2 The Manual ID Entry Method

3.8 License Management

3.8.1 Web Services

3.9.1 Specifying Alarm Reporting Types

3.9.1.1 The Display Line

3.9.1.2 The Alarm Output

3.9 Set Up Alarming

3.9.1.3 Dial-Out

3.9.1.4 The Echelon Network (The Alarm Annunciator)

3.9.2 Setting up an E2 to be an Alarm Annunciator

3.9.3 Alarm Dial-Out

3.9.4 Introduction: Alarm Reporting

3.10 Set Up Global Data

3.10.1 Priority Settings

3.11 Set Up Applications

3.11.1 Add/Delete an Application

3.11.2 Using and Configuring a Setup Screen

3.11.2.1 The Edit Menu

3.11.2.2 Entering Setpoints

3.11.2.3 Navigating the Setup Screen

3.11.3 Using the Help Key to Get Property Help

Appendix A: Troubleshooting