TO PREVENT FIRE OR SHOCK HAZARD, DO NOT USE THIS PLUG WITH AN
EXTENSION CORD, RECEPTACLE OR OTHER OUTLET UNLESS THE BLADES
CAN BE FULLY INSERTED TO PREVENT BLADE EXPOSURE. TO PREVENT FIRE
OR SHOCK HAZARD, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE.
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
The lightning flash with arrowhead symbol, within an equilateral triangle is intended to
alert the user to the presence
of uninsulated ‘dangerous voltage’
within the product’s enclosure
that may be of sufficient
magnitude to constitute a risk
of electric shock to persons.
WARNING: TO REDUCE THE
RISK OF ELECTRIC SHOCK
DO NOT REMOVE COVER
(OR BACK), NO U SER
SERVICEABLE PARTS INSIDE
REFER SERVICING TO
Q U A LI F IE D S E R VI C E
PERSONNEL.
The exclamation point within
an equilateral triangle is intended to alert the user to
the presence of important
operating and maintenance
(servicing) instructions in
the literature accompanying the appliance.
The Caution Marking maybe located at the bottom enclosure of the apparatus.
IMPORTANT SAFETY INSTRUCTIONS
1.) Read these instructions. Keep these instructions. Follow all instructions. Heed all warnings.
2.) Do not use this apparatus near water.
3.) Clean only with dry cloth.
4.) Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions.
5.) Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus
(including amplifiers) that produce heat.
6.) Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two
blades with one wider than the other. A grounding type plug has two blades and a third grounding
prong. The wide blade or the third prong is provided for your safety. If the provided plug does not
fit into your outlet, consult an electrician for replacement of the obsolete outlet.
7.) Protect the power cord from being walked on or pinched particularly at plugs, convenience
receptacles, and the point where they exit from the apparatus.
8.) Only use attachments / accessories specified by the manufacturer.
9.) Unplug this apparatus during lightning storms or when unused for long periods of time.
10.) Refer all servicing to qualified service personnel. Servicing is required when the apparatus has
been damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled
or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture,
does not operate normally, or has been dropped.
11.) This appliance shall not be exposed to dripping or splashing water and no object filled with liquids
such as vases shall be placed on the apparatus.
12.) Use only with the cart, stand, tripod, bracket, or table specified by the
manufacturer, or sold with the apparatus. When a cart is used, use caution
when moving the cart/apparatus combination to avoid injury from tip-over.
13.) Do not overload wall outlet. Use only power source as indicated.
14.) Use replacement parts as specified by the manufacturer.
15.) The product may be mounted to a wall only if recommended by the manufacturer.
16.) Upon completion of any service or repairs to this product, ask the service technician to perform
safety checks.
1
CKS3020_072706.p6527/7/2006, 11:351
Thank you ………………….
For purchasing this Emerson Research SmartSet® Dual Alarm Clock Radio with Triple
Display plus ‘Touchless’ Snooze and Display Control Features. We think you will be truly
amazed by all of the features that we have packed into this compact bedside companion.
First of all there is Emerson’s patented SmartSet® Automatic Time Setting System. The
first time you connect this clock radio to your AC outlet it will immediately set itself to the
correct year, month, date, day and time in the Eastern Time Zone. If you live in a different
time zone there is one simple Time Zone adjustment to make and you will never see the
dreaded “flashing 12:00” display again. It will automatically reset itself every time you
have a power interruption, and not just the time but your wake-up times as well. Daylight
Saving Time and Leap Year adjustments are also done automatically through the year
2099.
In addition to the jumbo amber time display there are two smaller displays that show the
Alarm 1 and Alarm 2 wake-up times, so you can see at a glance that the alarms are set
correctly. If one of the alarms is off, the display clearly shows “OFF”. No guesswork required.
Like to hit that snooze bar in the morning but don’t like reaching for the top of the radio?
Problem solved. Just wave your hand in front of the Touchless Snooze Wave Sensor and
go back to sleep for another 9 minutes. No touching required.
Love that big display that’s so easy to see but prefer to sleep in total darkness? We
thought of that one as well. Just set the display dimmer control to the “OFF/WAVE” position
and the display goes off completely. But if you need to check the time in the middle of the
night just wave your hand in front of the sensor. The display returns to full brightness for 10
seconds and then switches off again. Brilliant!
Just like every other SmartSet® model, this clock radio has a built-in, long-life lithium battery
that can provide back up for all of the important settings for up to 5 years or even longer.
No need to try and remember to install a fresh 9V battery ever 6 months. And when it’s
time to change the lithium battery the low battery indicator will ‘flash’ in the display.
We have taken great care to make sure that every feature in your clock radio was working
properly when it left our factory. If, after reading this manual completely, you have any
problems with the set-up or operation of this model, please do not return it to the retail
store. Please call the Emerson Consumer Products Customer Service Hotline, toll free, at
1-800-898-9020 between the hours of 9:00 AM and 5:00 PM Central Time. One of our
product specialists will try and solve the problem for you. If that is not possible you will be
instructed about the procedure to receive a replacement model.
Once again, thank you for purchasing this Emerson Research SmartSet® Clock Radio.
2
CKS3020_072706.p6527/7/2006, 11:352
IMPORTANT NOTES
• Avoid installing this unit in places
exposed to direct sunlight or close to
heat radiating appliances such as
electric heaters, on top of other stereo
equipment that radiates too much
heat, places lacking ventilation or dusty
areas, places subject to constant
vibration and/or humid or moist areas.
• Operate controls and switches as
described in the manual.
• Before turning on the power, make
certain that the power cord is properly
installed.
• When moving the set, be sure to first
disconnect the AC power cord.
FCC Information
This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to
provide reasonable protection agains t harmful interference in a residential
installation. This equipment generates, uses, and can radiate radio frequency energy
and, if not installed and used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which
the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including interference
that may cause undesired operation.
Changes or modifications not expressly approved by the party responsible for
compliance could void the user’s authority to operate the equipment.
3
CKS3020_072706.p6527/7/2006, 11:353
PREPARATION FOR USE
Unpacking And Set Up
• Remove the radio from the c arton and remove all packing material from the
radio. We suggest that you save the packing material, if possible, in the unlikely
event that your radio ever needs to be returned for service. The original carton
and packing material is the only safe way to pack your radio to protect it from
damage in transit.
• Remove any descriptive labels or stickers on the front or top of the cabinet. Do
not remove any labels or stickers from the back or bottom of the cabinet.
• Note the serial number on the bottom of your radio and write this number in the
space provided on the Warranty page of this manual.
• Place your radio on a level surface such as a table, desk or shelf, convenient
to an AC outlet, out of direct sunlight, and away from sources of excess heat,
dirt, dust, moisture, humidity, or vibration.
• Unwind the AC power cord and extend it to its full length. The FM antenna is
built in to this cord. It must be fully extended to provide the best FM reception.
Protect Your Furniture
This model is equipped with non-skid rubber 'feet' to prevent the product from
moving when you operate the controls. These 'feet' are made from non-migrating
rubber material specially formulated to avoid leaving any marks or stains on your
furniture. However certain types of oil based furniture polishes, wood preservatives,
or cleaning sprays may cause the rubber 'feet' to soften, and leave marks or a
rubber residue on the furniture. To prevent any damage to your furniture we strongly
recommend that you purchase small self-adhesive felt pads, available at hardware
stores and home improvement centers everywhere, and apply these pads to the
bottom of the rubber 'feet' before you place the product on fine wooden furniture.
4
CKS3020_072706.p6527/7/2006, 11:354
Power Source
AC Outlet
This radio is designed to operate on normal 120V 60Hz AC power only. Do not
attempt to operate the radio on any other power source. You could cause damage
to the radio that is not covered by your warranty.
This radio should be connected to an AC outlet that is always ‘live’. Do not connect
it to an outlet that is controlled by a wall switch. When the power to the radio is
interrupted, the built in lithium battery takes over to maintain the time and alarm
settings. To maximize the life of the lithium battery keep the radio connected to a
‘live’ AC outlet at all times.
You will note that this system is equipped with a polarized AC power plug having
one blade wider than the other. This is a safety feature. If this plug does not fit into
your existing AC outlet, do not try to defeat this safety feature by filing the wide
blade to make it fit into your outlet.
If this plug will not fit into your outlet, you probably have an out-dated non-polarized
AC outlet. You should have your outlet changed by a qualified licensed electrician.
CKS3020_072706.p6527/7/2006, 11:355
AC Plug
5
LOCATION OF CONTROLS AND INDICATORS
Front Panel
6
5
4
3
2
1
Top Panel
16
15
17
18
13
78
19
20
21
9
28
10
11
12
22
23
24
14
Left Side Panel
27
CKS3020_072706.p6527/7/2006, 11:356
25
26
9
4
10
3
11
2
6
Right Side Panel
1.) ALARM 1 Time (Month/Date) Display.
2.) DIMMER (HIGH-LOW-OFF/WAVE) Selector Switch .
3.) ALARM2 (RADIO/BUZZER/OFF) Selector Switch.
4.) ALARM1 (RADIO/BUZZER/OFF) Selector Switch.
5.) Time Display.
6.) AM Indicator.
7.) DAY OF WEEK (MON, TUE, WED, THU, FRI, SAT, SUN) Indicators.