Emerson CKD9917BK, CKD9917 User Manual
TM
SmartSet®Dual Alarm Clock Radio
with CD Player
(U.S. Patent No. 6,567,344)
OWNER'S MANUAL
CKD9917BK
CKD9917
Visit our web site at www.emersonradio.com
CAUTION
TO PREVENT FIRE OR SHOCK HAZARD, DO NOT USE THIS PLUG WITH AN EXTENSION CORD, RECEPTACLE OR OTHER OUTLET UNLESS THE BLADES CAN BE FULLY
INSERTED TO PREVENT BLADE EXPOSURE. TO PREVENTFIRE OR SHOCK HAZARD,
DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE.
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
The lightning flash with arrowhead symbol, within an equilateral triangle is intended to
alert the user to the presence of
uninsulated dangerous voltage
within the products enclosure that
may be of sufficient magnitude to
constitute a risk of electric shock
to persons.
The Caution Marking may be located at the bottom enclosure of the apparatus.
Les précautions d’emploi sont inscrites en bas de l’appareil.
WARNING: TO REDUCE THE
RISK OF ELECTRIC SHOCK
DO NOT REMOVE COVER
(OR BACK), NO USER
SERVICEABLE PARTS
INSIDE REFER SERVICING
TO QUALIFIED SERVICE
PERSONNEL.
The exclamation point within
an equilateral triangle is
intended to alert the user to
the presence of important
operating and maintenance
(servicing) instructions in the
literature accompanying the
appliance.
IMPORTANT SAFETY INSTRUCTIONS
1.) Read these instructions. Keep these instructions. Follow all instructions. Heed all warnings.
2.) Do not use this apparatus near water.
3.) Clean only with dry cloth.
Do not block any ventilation openings. Install in accordance with the manufacturer’s
4.)
instructions.
5.) Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus
(including amplifiers) that produce heat.
6.) Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has
two blades with one wider than the other. A grounding type plug has two blades and a third
grounding prong. The wide blade or the third prong is provided for your safety. If the
provided plug does not fit into your outlet, consult an electrician for replacement of the
obsolete outlet.
7.) Protect the power cord from being walked on or pinched particularly at plugs, convenience
receptacles, and the point where they exit from the apparatus.
8.) Only use attachments / accessories specified by the manufacturer.
9.) Unplug this apparatus during lightning storms or when unused for long periods of time.
10.) Refer all servicing to qualified service personnel. Servicing is required when the apparatus
has been damaged in any way, such as power-supply cord or plug is damaged, liquid has been
spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or
moisture, does not operate normally, or has been dropped.
11.) This appliance shall not be exposed to dripping or splashing water and no object filled with
li
quids such as vases shall be placed on the apparatus.
L’appqreil ne doit pas être exposé aux écoulements ou éclaboussures et aucun objet ne
contenant de liquide，tel qu’un vase, ne doit être placé sur l’objet.
12.) Use only with the cart, stand, tripod, bracket, or table specified by the
manufacturer, or sold with the apparatus. When a cart is used, use caution
when moving the cart/apparatus combination to avoid injury from tip-over.
1
13.) Do not overload wall outlet. Use only power source as indicated.
14.) Use replacement parts as specified by the manufacturer.
15.) The product may be mounted to a wall only if recommended by the manufacturer.
Upon completion of any service or repairs to this product, ask the service technician to
16.)
perform Safety
17.)
This is CLASS II apparatus with double insulation, and no protective earth provided.
Before We Begin
Thank you for purchasing this Emerson audio product. The Emerson brand is your
assurance of quality, performance and value.
Our engineers have included many useful and convenient features in this product.
Please be sure to read this Owner's Manual completely to make sure you are getting
the maximum benefit from each feature.
This product was manufactured using the highest quality components and standards of
workmanship. It was tested by Emerson inspectors and found to be in perfect working
order before it left our factory. However, there is always the chance that some
problem may occur because of rough handling during shipment to the retail store or to
the final consumer.
If, after reading this Manual, you experience any problems with the operation of this
product, please refer to the instructions for obtaining service at the end of this Manual.
Emerson and Emerson retailers are committed to your satisfaction.
2
IMPORTANT NOTES
CLASS 1 LASER PRODUCT
This product contains a low power Laser Device.
•
Avoid installing this unit in places
exposed to direct sunlight or close to
heat radiating appliances such as
electric heaters, on top of other stereo
equipment that radiates too much heat,
places lacking ventilation or dusty
areas, places subject to constant
vibration and/or humid or moist areas.
FCC Information
This equipment has been tested and found to comply with the limits for a class
B digital Device, pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses, and can radiate radio
frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or more of
the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which
the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
This device complies with part 15 of the FCC Rules. Operation is subject to the
following two conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including interference
that may cause undesired operation.
Changes or modifications not expressly approved by the party responsible for
compliance could void the user’s authority to operate the equipment.
•
Operate controls and switches as
described in the manual.
• Before turning on the power, make
certain that the power cord is properly
installed.
• When moving the set, be sure to first
disconnect the power cord and remove
cords connected to other equipment.
3
MPORTANT NOTES
Unpacking And Set Up
Remove the unit from the carton, and remove all packing materials from the
unit.
Save the carton and packing materials in case the unit ever needs to be
returned for service. Using the original carton and packing materials is the
only way to safely repack the unit for shipment.
Remove any descriptive labels or stickers from the top or front of the unit. Do
not remove any labels from the back or bottom of the cabinet.
Remove any small strips of tape that may have been used to prevent the CD
from opening in transit.
Press the CD door in the area marked OPEN/CLOSE button to open the CD
door and remove the ‘dummy CD’ protection card from the CD player and
discard it. Close the CD door.
Unwind the AC power cord and extend it to its full length.
Place the unit on a stable, level surface such as a table, desk, shelf, etc.,
within easy reach of an AC outlet, out of direct sunlight, and away from
sources of excessive heat, dust, moisture or humidity.
PREPARATION FOR USE
Protect Your Furniture
This model is equipped with non-skid rubber 'feet' to prevent the product from
moving when you operate the controls. These 'feet' are made from
non-migrating rubber material specially formulated to avoid leaving any marks
or stains on your furniture. However certain types of oil based furniture
polishes, wood preservatives, or cleaning sprays may cause the rubber 'feet' to
soften, and leave marks or a rubber residue on the furniture. To prevent any
damage to your furniture we strongly recommend that you purchase small
self-adhesive felt pads, available at hardware stores and home improvement
centers everywhere, and apply these pads to the bottom of the rubber 'feet'
before you place the product on fine wooden furniture.
4
5
Battery Back Up System
This unit uses a single CR2032 battery (included) to maintain the time and
alarm settings in the event that it is accidentally unplugged, or you experience
a temporary power failure. We recommend that you install a well-known brand
of Alkaline battery for longest life and best performance.
Installing and replacing the backup battery
1.) Use screw driver to remove the screw that secures the battery compartment
at the bottom of the unit,and remove the battery compartment.
2.) Insert a new battery in the battery comparment with " + " side facing up.
3.) Insert the battery compartment back into the unit and secure it with the screw.
1 2 3
If the power is interrupted the clock display will go off but the battery will
maintain the clock and alarm time settings. When power is restored the time
display will be correct and your alarm setting will also be maintained.
If you notice that the time display is completely wrong you probably
experienced a power failure with a weak or exhausted battery in the
compartment. Reset the clock and replace the battery as soon as possible.
If you do not change the built in lithium battery
AM
within a reasonable period of time after you see
the ‘flashing’ LOW BATTERY warning indicator,
the lithium battery may become exhausted and
AL1
MON
AL2
will no longer be able to supply back up power to the SmartSet® internal
computer. If the unit is disconnected from the AC outlet after the battery is
exhausted, or if power interruption occurs, the SmartSet® memory will be lost
and this clock will need to be reset when the power is restored. Be sure to
install a fresh lithium battery before you reset the clock, otherwise the clock will
need to be reset each time the power is interrupted. If this lithium battery is
exhausted and you experience an interruption in the AC power supply, the
clock will reset itself to its initial default setting when the power restored.
6
7
LOCATION OF CONTROLS AND INDICATORS
Loading...