Elnur PH075, PH125, PH075T, PH125T, PH150 Installation Instructions And User Manual

INSTALLATION INSTRUCTIONS
AND USER GUIDE

CONVECTOR HEATER

PH075 AND PH075T
PH125 AND PH125T
PH150 AND PH150T
PH200 AND PH200T

RATING 750 W
RATING 1250 W
RATING 1500 W
RATING 2000 W

230 – 240 V~
230 – 240 V~
230 – 240 V~
230 – 240 V~

Please read these instructions before installing or

using this appliance for the rst time

IECEEIECEE

CB

SCHEME

Panel Convector Heaters

2

1.- IMPORTANT INFORMATION

• The warranty of the panel heater will not cover any damage caused by non observance of any of these instructions.

• This Guide must be kept and given to any new owner.

• Before connecting this appliance to any power supply, the wall fixing bracket located below has to be detached.

• Check that the voltage shown on the rating plate on the heater is the same as the voltage of the supply to which connection is to be

made.

• Should the heater be moved and reinstalled it is essential that the work is carried out by a competent electrician.

• The use of panel heaters is forbidden in any area where there is a presence of gases, explosives or inflammable objects.

• Do not use this heater to dry clothes.

• Neither the connecting cable nor any other object must come into contact with the hot unit.

• Do not cover this heater at any time.

• The surfaces of this heater can be hot, so young children should not be left unsupervised in the vicinity of the heater.

• The air outlet grill at the top of the heater cabinet and the air inlet at the bottom of the heater are provided to ensure the most efficient

operation of the appliance. They also protect the heater from overheating; therefore, it is essential that at no time are they covered.

• This heater should be disconnected from the electricity supply before any repair work is carried out. This action should also be tak

en

during the times of the year when heat is not required.

• The panel heater should not be installed just below an electrical socket.

• The appliance must be installed in such a way that switches and other control devices cannot be touched by a person using a bath or

shower.

• The installation must be carried out in accordance with the current electrical regulations.

• The heater is fitted with a flexible cable size 3 x 1.00 mm2 for electrical connection. It may be used to connect the heater to the fi

xed

wiring of the premised through a suitable connection box positioned adjacent to the panel heater.

• This appliance must be connected to the supply by fixed wiring. The supply circuit to the heater must incorporate a double pol

e

isolating switch having a contact separation of at least 3 mm.

• If the flexible power cable for this unit is damaged, it may only be replaced by a repair workshop recognised by the manufacturer, as
special tools are necessary.

• This appliance must be earthed.

• Before carrying out any work inside the appliance, the panel heater must be disconnected from the electricity supply.

• The presence in the air of particles of smoke, dust and other pollutants could, in time, discolour the walls and surfaces around the

panel heater.

• Please complete the enclosed warranty card and return it to the manufacturer to enable registration to take place.

All models are supplied with an electrical interrupt cut-out. This will switch off the heater if, for any reason, it overheats. Should the cut­out operate, turn the heater off and remove the cause for the overheating. The cut-out will be reset automatically.

2. – INSTALLATION INSTRUCTIONS

- When positioning the heater for installation it is important
that a minimum clearance of 50 cm must be allowed
between the heater and any combustible materials, such
as furniture, curtains etc, to ensure the best heating
results.

41.0 cm ( 750W)

56.0 cm (1250W)

63.5 cm (1500W)

78.5 cm (2000W)

min 15cm

min 15cm

mi n 2 0 cm

mi n 2 0 cm

41.0 cm

8cm

10cm

Fig. 1

- Open the carton at the indicated side. The screws are in the
accessories bag. Turn the carton upside down to allow the heater to
stand. Check that it is the correct model and that it is in good condition.

- Fix the two square brackets to the back of the heater by using the two
small screws (see Fig. 1).

Fig. 2

Panel Convector Heaters

3

- Position and fix the top bracket at the correct distance from the floor (see Fig. 2) and hang the unit on the hooks of the top bracket.
Mark the fixing points on the wall using a pencil. Use the heater fixing holes as a template and mark the wall through the two fixing holes
in the square brackets. Fix the heater to the wall.

3.- USING THE PANEL HEATER

NON TIMER MODELS

Open the hinged controls cover to access the controls. After
adjustment the control cover closes automatically.

Switch on the heater by setting one of the two switches marked I-O
to “ I “. The off position is marked “ O “.

You can select half heat or full heat by setting only one of the switches
marked I-O to “ I “ or by setting the two ones (this feature is not
available on 750W models). When the heater is generating heat the
neon indicator on the switch will be illuminated.

The heater is fitted with an adjustable thermostat, which enables room
temperature to be controlled by adjusting the setting accordingly. Turn
the thermostat control to the maximum (fully clockwise) to heat the
room rapidly. When the desired temperature has been reached, turn
the thermostat control slowly to the left (anti-clockwise) until the
luminous indicator switches off. By leaving in this position, the heater
will automatically maintain the selected temperature.

TIMER MODELS

If the slide switch marked I -O- ! is set to the position marked “ I “ the
heater will be always on, under the control of the thermostat as a non timer
model.

If the slide switch marked I -O- ! is set to the position marked “O “ the
heater will be in the off position.

If the slide switch marked I -O- ! is set to the position marked “ ! “ the
heater will operate automatically. Set the timer by rotating the dial clockwise
until the correct time is indicated opposite the datum mark. Pull the
appropriate segments out to set the desired programme. This programme
will repeat itself every day. The timer may be set to give as many “on”
periods of any length as may be required.

The switch marked I – II provides a choice of half heat or full heat. (not
available on 750W models). When the heater is generating heat the neon
indicator on the switch will be illuminated.

3.- Cleaning and maintenance.

Clean and dust with a dry, soft cloth only when the unit is disconnected and
cold. Do not use solvents or abrasive products for cleaning.

Panel Convector Heaters

4.- WIRING

T: 24h Timer
E1: Element 1
E2: Element 2
S: Safety cut out
C: Switch
L: Luminous indicator
Ta: Ambient thermostat

PH-125T
PH-150T
PH-200T

PH-075T

PH-075

PH-125
PH-150
PH-200

WARNING: In order to avoid overheating do not cover the heater.

The symbol on the product or in its packaging indicates that this product may not be treated as household waste. Instead it
shall be handed over to the applicable collection point for the recycling of electrical and electronic equipment. By ensuring
this product is disposed of correctly, you will help prevent potential negative consequences for the environment and human
health, which could otherwise be caused by inappropriate waste handling of this product. For more detailed information
about recycling of this product, please contact your local city office, your household waste disposal service or the shop
where you purchased the product. These instructions are only valid in the EU member states.

ELNUR UK Ltd.

Unit 1, Brown Street North

Leigh, Lancashire

WN7 1BU

www.elnur.co.uk

Customer Service Department:

Telephone [phone]

[e-mail]

Manufactured by:

ELNUR, S.A.

Madrid, Spain

www.elnur-global.com

[e-mail]

Management System International Certifications:

As a part of the policy of continuous product improvement Elnur reserves the right to alter specifications without notice.

INSTALLATION INSTRUCTIONS AND USER GUIDE WEB VERSION