Electrolux EI27EW35JS1, EI27EW35KB1, EI27EW35KW1, EI27EW45JS1, EI27EW45JS2 Installation Guide

iNSTALLATiON AND SERVICE MUST BE PERFORMED BY A QUALiFiED iNSTALLER.

iMPORTANT: SAVE FOR LOCAL ELECTRICAL iNSPECTOR'S USE.

READ AND SAVE THESE iNSTRUCTiONS FOR FUTURE REFERENCE.

FOR YOUR SAFETY: Do not store or use gasoline or other flammable vapors and liquids in

the vicinity of this or any other appliance.
Your new wall oven has been designed to fit a limited variety of cutout sizes to make the job of installing

easier. The first step of your installation should be to measure your current cutout dimensions and
compare them to the cutout dimensions chart below for your model. You may find little or no cabinet
work being necessary.

Do not remove spacers (if equipped) on the side walls and/or on the back of the built-in

oven. These spacers center the oven in the space provided. The oven must be centered to prevent
excess heat buildup that may result in heat damage or fire.

NOTES: _____._

1. Base must be capable of supporting 150 pounds (68 kg) for 27" _1 .... <------_ '-_

models and 200 _ounds (90 k-) for 30" models ,y2" _J._cm) _ _/

2. Allow at least21 " (53.3 cm) clearancein front of oven for door depth _ _ [_

when it isopen. J _ ....

3. Dimension G (cutout depth) iscritical to _ _" C. ' -_ _ G_'}} >, Hole for

the proper installation of the built-in oven. t ..-_ j_t _ _-----'_-_,KJ ....... i Cable

If the oven decorative trim does not butt / H E--..., _-"
against the cabinet, or if noise is heard on B 27 3/16"

convection models, verify dimension G to (69.1 cm) < _? ...... i 3"

assure it isthe required depth. _ ' --.,_" .... :?_)_ ",

4. For a cutout height greater ....... 31"* _<:_

than 27s/8'' (70.2 cm) add one _ ...-_ (78.7 im) _,:j_._

2"(5 cm) wide wood shim of .... / _ _ "'P--

appropriate height to each side ... i....... I.j Spacer _ , \

of the opening under the apphance side rails. _'_'A I M,o. _.

Lifting the unit will allow you to hide the _ I "-,,"_, _ '-_/" Electrical
cutout openings showing above the unit. The bottom "1 2" (5 cm) Wide Wood Spacer'''Jt_ Junction Box

trim of the untt wtll htde the shtms at the bottom, if Needed (See note 4)

5 For a cutout heiqht (H) qreater than 28V4' (71 8 cm)

" "_ "_ " 9¢ ' , ii

you can order a larger inferior trim, contact your Service Suggested @stance from floor ts31 (78.7 cm).

Center. Minimum required distance is 4 _/2" (11.4 cm).

P 9 " Min.

.... _ , (7 6 cm)

__ ii!iiiiiiii!iji{ili_iliiii!i!i!_i!iliiiiiiilili!ii_ _/-'/

. . uoor upen = ..... - |

tsee no%e z) .... - I /u a , ._ L_ _" 2" \

.... "" -_._. (5.1 cm)

Figure 1

27" and 30" Single Wall Ovens (Double ovens see Figure 2)

27" (68.6 cm) Wall Oven

30" (76.2 cm)Wall Oven

27" (68.6 cm) Wall Oven

30" (76.2 cm)Wall Oven

All dimensions are in inches (cm).

Printed in United States

247/s (63.2) 2%A (64.1) 23_/2(59.7) 27_A (69.2) 281A (71.8) 27Vs (68.9) Min

2@/2(72.4) 29 (73.7) 231/2(59.7) 27_A (69.2) 281A (71.8) 30Vs (76.5) Min

27 (68,6)

30 (76.2)

29 (73.7)

29 (73.7)

24% (62.5)

28X (71.8)

24Y2 (62.2)

24Y2 (62.2)

P/N 318201528 (0801) Rev. D

English - pages 1-8

Espahol - paginas 9-16

Fran_ais -pages 17-24

oven. These spacers center the oven in the space provided. The oven must be centered to prevent

_ Do not remove spacers (if equipped) on the side walls and/or on the back of the built-in

excess heat buildup that may result in heat damage or fire.

1Y2" (3.8Min.Cm)" I

B

48 5/8"

(123.5 cm)

Door Open

(seenote 2)

2" (5 cm)Wide Wood Spacer

if Needed (see note 4)

NOTES:

1. Base must be capable of supporting 300 pounds
(136 kg) for 27" models and 375 pounds (170 kg)

for 30" models,

2. Allow at least 21 " (53,3 cm) clearance in front of
oven for door depth when it is open.

3. Dimension G (cutout depth) is critical to the proper
installation of the built-in oven. If the oven

decorative trim does not butt against the cabinet, or
if noise is heard on convection models, verify

dimension G to assure it is according to the required
dimension.

27" AND 30" DOUBLE OVENS (Single Ovens see Figure 1)

(29.2

Spacer

Figure 2

H

11Y2"

3" (7.6 cm)

Max.

Junction Box

4. For a cutout height greater than 49¼" (125.1 cm)
add a 2" (5 cm) wide wood shim of appropriate
height to each side of the opening under the
appliance side rails, Lifting the unit will allow you to
hide the cutout openings showing above the unit,

The bottom trim of the unit will hide the shims at
the bottom.

5. For a cutout height (H) greater than 49%" (126.4
cm) you can order a larger inferior trim through
your Service Center.

27" (68.6 cm)Wall Oven 27 (68.6)

30" (76.2 cm)Wall Oven 30 (76.2)

27" (68.6 cm) Wall Oven 247/8(632)

30" (76.2 cm) Wall Oven 28V2 (72.4)

All dimensions are in inches (cm).

251A (64,1)

29 (73.7)

50716 (I 28.1 ) 24% (62.5) 241/2(62 2)

50716 (I 28. I ) 281A (71.8) 24Y2 (62 2)

231/2(59.7) 487/8(124-1) 49_A(126"4) 27%(68.9) Min

231/2(59.7) 487/8 (124.1) 49_A(126.4) 30I/8 (76.5) Min

Important Notes to the Installer

1. Read all instructions contained in these installation
instructions before installing the wall oven.

2. Remove all packing material from the oven
compartments before connecting the electrical supply

to the wall oven.

3. Observe all governing codes and ordinances.

4. Be sure to leavethese instructions with the consumer.

5. Oven door may be removed to facilitate installation.

6. THESEOVENS ARE NOT APPROVED FOR
STACKABLE OR SIDE-BY-SIDE INSTALLATION.

Important Note to the Consumer

Keep these instructions with your Owner's Guide for future
reference.

IMPORTANT SAFETY

2. Electrical Requirements

This appliance must be supplied with the proper voltage
and frequency, and connected to an individual, properly
grounded branch circuit, protected by a circuit breaker or
fuse. To know the circuit breaker or fuse required by
your model, see the serial plate to find the wattage
consumption and refer to table A to get the circuit
breaker or fuse amperage.

Appliance Protection Appliance Protection

RatingWatts Circuit RatingWatts Circuit

240V recommended 208V recommended
lessthan 4800W 20A Lessthan 4100W 20A
4800W- 7200W 30A 4100W-6200W 30A
7200W- 9600W 40A 6200W-8300W 40A

9600Wand + 50A 8300Wand + 50A

INSTRUCTIONS

* Be sure your wall oven is installed and grounded

properly by a qualified installer or service
technician.

* This wall oven must be electrically grounded in

accordance with local codes or, in their absence,
with the National Electrical Code ANSI/NFPA

No.70- latest edition in United Sates, or with CSA
Standard C22.1, Canadian Electrical Code, Part 1, in

Canada.

Stepping, leaning or sitting on the

door of this wall oven can result in serious injuries
and can also cause damage to the wall oven.

• Never use your wall oven for warming or heating
the room. Prolonged use of the wall oven without
adequate ventilation can be dangerous.

The electrical power to the oven must

be shut off while line connections are being made.

Failure to do so could result in serious injury or

death.

1. Carpentry

Refer to figure 1 or 2 for the dimensions applicable to

your appliance, and the space necessary to receive the
oven. The oven support surface may be solid plywood or

similar material, however the surface must be level from
side to side and from front to rear.

Table A

Observe all governing codes and local ordinances

I.A 3-wire or 4-wire single phase 120/240 or 120/208

Volt, 60 Hz AC only electrical supply is required on a
separate circuit fused on both sides of the line (red and
black wires). A time-delay fuse or circuit breaker is
recommended. DO NOT fuse neutral (white wire). Only
certain cooktop models may be installed over certain
built-in electric oven models. Approved cooktops and
built-in ovens are listed by the MFG ID number (see
the insert sheet included in the literature package).

NOTE: Wire sizes and connections must conform with
the fuse size and rating of the appliance in accordance

with the American National Electrical Code ANSI/NFPA
No. 70-latest edition, or with Canadian CSA Standard

C22.1, Canadian Electrical Code, Part 1, and local codes
and ordinances.

An extension cord should not be used

with this appliance. Such use may result in a fire,
electrical shock, or other personal injury. If you need
a longer power cord you can purchase a 10' (3 m) power
cord kit #903056-9010 by calling the Service Center.

2. These appliances should be connected to the fused
disconnect (or circuit breaker) box through flexible

armored or nonmetallic sheathed cable. The flexible
armored cable extending from the appliance should

be connected directly to the junction box. The

junction box should be located asshown in Figure I

or Figure 2 and with as much slack as possible

remaining in the cable between the box and the

appliance, so it can be moved if servicing is ever

necessary.

3. A suitable strain relief must be provided to attach
the flexible armored cable to the junction box.

Electrical Shock Hazard

• Electrical ground is required on this appliance.

• Do not connect to the electrical supply until
appliance is permanently grounded.

• Disconnect power to the junction box before

making the electrical connection.

• This appliance must be connected to a
grounded, metallic, permanent wiring system,
or a grounding connector should be connected
to the grounding terminal or wire lead on the
appliance.

• Do not use a gas supply line for grounding the
appliance.

Failure to do any of the above could result in a

fire, personal injury or electrical shock.

In cold weather shipping and storage
conditions, make sure that oven is in final location at
least three (3) hours before switching on power.

Switching on power while oven is still cold may damage
the oven controls.

Where local codes permit connecting the appliance-
grounding conductor to the neutral (white) wire
(US Only) (see figure 3):

1. Disconnect the power supply.

2. In the circuit breaker, fuse box or junction box:
connect appliance and power supply cable wires as
shown in Figure 3.

Cable from Power Supply

White Wire

(Neutral)

Wires

Red

Wires

Box

Wire

(Neutral)

Ground Wire U.L-Listed Conduit
(Bare or Green Wire) Connector (or CSA listed)

Cable from appliance

Figure 3

3-WIRE GROUNDED JUNCTION BOX

3. Adjusting Oven Height

Oven height can be adjusted with 2" (5 cm) wide wood
shims when needed to fit into an existing cabinet cutout
opening, when cutout height exceeds 281/8"(71.4 crn) for
the single wall oven or 491/z'' (125.7 crn) for the double
wall oven (see Figure 1 or 2). Place shims of appropriate
height beneath the oven side rails.

4. Electrical connection

It is the responsibility and obligation of the consumer to
contact a qualified installer to assure that the electrical

installation is adequate and is in conformance with the
National Electrical Code ANSI/NFPA No. 70-latest

edition, or with CSA Standard C22.1, Canadian
Electrical Code, Part 1, and local codes and ordinances.

Electrical ground is required on this appliance.

These appliances are equipped with a copper conductor
flexible cable. If connection is made to aluminum house

wiring, use only special connectors which are approved
for joining copper and aluminum wires in accordance

with National Electrical Code and local codes and
ordinances.

_!_ Improper connection of aluminum

house wiring to copper leads can result in a short
circuit or fire. Use only connectors designed for

joining copper to aluminum, and follow the

manufacturer's recommended procedure closely.

You may not ground the oven

through the neutral (white) wire if oven is used in
a new branch circuit installation (1996 NEC), mobile
home, recreational vehicle, or where local codes do
not permit grounding through the neutral (white)
wire. When grounding through the neutral (white)
wire is prohibited, you must use a 4-wire power
supply cable. See Figure 4. Failure to heed this
warning may result in electrocution or other
serious personal injury.

These appliances are manufactured with a white neutral
power supply wire and a frame connected green or bare
copper grounding wire.

if oven is used in a new branch circuit installation
(1996 NEC), mobile home, recreational vehicle, or
where local codes DO NOT permit grounding

through the neutral (white) wire (see figure 4):

1. Disconnect the power supply.

2. Separate the green (or bare copper) and white
appliance cable wires.

3. In the circuit breaker, fuse box or junction box:
connect appliance and power supply cable wires as
shown in Figure 4.

Cable from Power Supply

Wire

Wires

Ground Wire
(Bare or

Wire)

Junction Box U.L-Listed Conduit

Connector (or CSA listed)

Cable from appliance

Figure 4

4-WIRE GROUNDED JUNCTION BOX

Heavy Weight Hazard

• Use 2 or more people to move and install wall oven.

• Failure to follow this instruction can result in injury
or damage to the unit.

Model and Serial Number Location

The serial plate is located along the interior side trim of
the oven and visible when the door is opened.

When ordering parts for or making inquires about your
oven, always be sure to include the model and serial
numbers and a lot number or letter from the serial plate

on your oven.

Single Wall Oven
Serial Plate Location

DO NOT ground to a gas supply pipe. DO NOT connect
to electrical power supply until appliance is permanently
grounded. Connect the ground wire before turning on
the power (Figure 4).

If connecting to a 4-wire electrical

system (mobile homes), the appliance frame MUST
NOT be connected to the neutral wire of the 4-wire

electrical system.

NOTE TO ELECTRICIAN: The armored cable leads
supplied with the appliance are UL-recognized for

connection to larger gauge household wiring. The

insulation of the leads is rated at temperatures much

higher than temperature rating of household wiring. The
current carrying capacity of the conductor is governed by
the temperature rating of the insulation around the wire,

rather than the wire gauge alone.

Double Wall Oven

Serial Plate Location

5. Cabinet installation

Do not lift the oven by the door handle.

1. Unpack the wall oven. Remove the bottom trim taped
on the oven side panel.

2. Find the 2 anti-tip mounting screws included in the
literature package.

3.Insert the oven into the cabinet opening. Slide oven

inward leaving IY2" (3.8 cm) clearance between the
oven and front of cabinet (see Figure 5).

4.Pullthe armored cable through the hole for it in the

cabinet and toward the junction box while moving the
appliance inward.

5.Push the oven in and against the cabinet.

IMPORTANT i

...... -._...._.....

..........

Figure 6

7.Install the Bottom Trim
Placethe top of the bottom trim over the side trim tabs on

each side of the oven below the oven door and fix it using
the 2 screws supplied inthe mounting holes located on
each side trim below the oven frame (seeFigure 7).

J

]...i

1V2" (3.8 cm)

clearance

between unit

Y

Figure 5

6. Install the Anti-tip Mounting Screws
The wall oven can tip when the door

is open. The anti-tipmounting screws supplied
with the wall oven must be installed to prevent

tipping of the wall oven and injury to persons.
A. The mounting holes in the side trims may be used as a

template to locate the appliance mounting screw

holes (seefigure 6).

B. Use the two screws supplied to fix the appliance to

the cabinet.

ScFews

Bottom Trim

Figure 7

Fortypicalundercounterinstallationofanelectricbuilt-inovenseeFigurebelow.

Onlycertaincooktopmodelsmaybeinstalledovercertain
built-inelectricovenmodels.Approvedcooktopsandbuilt-
inovensarelistedbytheMFGIDnumberandproduct
code(seetheinsertsheetincludedintheliteraturepack-
ageandcooktopinstallationinstructionsfordimensions

Toreduce the risk of

personal injury and
tipping of the wall

oven, the wall oven
must be secured to

the cabinet (s) by
mounting brackets.

208/240 Volt junction box.

for built-in oven.

Cabinet side filler panels are
necessaryto isolate the unit

from adjoining cabinets. Cabinet

sidefiller height should allow for
installation of approved cooktop

models

Approx. 3

(7.5 cm)

36" Min.
(91.4 cm) Min.

Use3/4" (1.9 cm) plywood, installed on two

runners, flush with toe plate. Basemust be
capable of supporting 150 pounds (68 kg)
for 27" models and 200 pounds (90 kg) for

30" models.

* If no cooktop is installed directly over

the oven unit, 5" (12.7 cm) maximum
is allowed above the floor.

Figure 8- TYPICAL UNDER COUNTER INSTALLATION OF A SINGLEELECTRICBUILT-IN OVEN

WITH AN ELECTRICCOOKTOP MOUNTED ABOVE

Cut an opening in wood base minimum 9" x 9"
(23 X 23 cm), 2" (5 cm) from left side filler

panel, to route armoured cable to junction box.

4 1/2" (11.5 cm) Max.*

27" (68.6 cm) 247/8'' (63.2 cm) Min. 27_A" (69.2 cm) Min.

Wall Oven 25_A'' (64.1 cm) Max. 23Y2" (59.7 cm) Min. 28Y4" (71.8 cm) Max.

30" (76.2 cm) 28Y2" (72.4 cm) Min. 27Y4" (69.2 cm) Min.

Wall Oven 29" (73.7 cm) Max. 23Y2" (59.7 cm) Min. 28Y4" (71.8 cm) Max.

FlexibleApl

Wall Oven Cabinet

Figure 9 - TYPICAL UNDER COUNTER INSTALLATION OF A SINGLE ELECTRICBUILT-IN OVEN

Cabinet sides or

filler panel

WITH A GAS COOKTOP ABOVE

18"(45.7 cm) Max. ---"_I

tJ_ I

i

I

I

5" Max. 6 I/2" Min.

Flare(12.Tcm) (16.5c__

Union J,

'-:-'_= z _-,,, 120V/_600Hz

---- ,--_-" _ Grounded
Hare __ Outlet

Union

Pressure
Regulator

_Manual

Shutoff

Valve

j 4,

4"(10 cm)

Right Side

of Cabinet

(To be

accessible

for shut-off

valve

operation)

6. Leveling the Wall Oven

1. Install an oven rack in the center of the upper oven
(see Figure 10).

2. Place a level on the rack. Take 2 readings with the
level placed diagonally in one direction and then the

other. Use wood shims under the wall oven to level

if necessary.

3. Repeat in the lower oven if you have a double cavity

wall oven. If the level indicates that the rack is not

level, use wood shims to reach a compromise for
both ovens.

Figure 10

IMPORTANT NOTE

A cooling fan inside the upper rear part
above the oven (some models) provides

cooling of the oven electrical and
electronic components, If the oven has

been operating at high temperatures, the

fan will continue to run after the oven is
turned off,

7. Checking Operation

Your model is equipped with an Electronic Oven
Control. Each of the functions has been factory checked

before shipping. However, it is suggested that you verify

the operation of the electronic oven controls once more.

Refer to the Use and Care Guide or the Timer Guide

for operation.

I. Remove all items from the inside of the oven.

2. Turn on the power to the oven (Refer to your Use &
Care Guide.)

3. Verify the operation of the electronic oven controls:

Bake- Verify that this function makes the oven hot.
20 seconds after turning oven on, open the door and
you should feel heat coming from the oven.

Broil- When the oven is set to BROIL,the upper
element in the oven should become red.

Convection (some models)-When the oven is set for
a convection baking or roasting, both elements cycle
on and off alternately and the convection fan will run.
The convection fan will stop running when the oven
door is opened.

Before You Call for Service

Read the "Before You Call for Service Checklist" and the
"Operating Instructions" in your Use and Care Guide. It

may save you time and expense. The list includes

common occurrences that are not the result of defective
workmanship or materials in this appliance.

Refer to your Use and Care Guide for service phone
numbers.