Electrolux EEZ89300W User guide

EEZ89300W

EN User Manual | Dishwasher

WE’RE THINKING OF YOU

Thank you for purchasing an Electrolux appliance. You’ve chosen a product that brings
with it decades of professional experience and innovation. Ingenious and stylish, it has
been designed with you in mind. So whenever you use it, you can be safe in the
knowledge that you’ll get great results every time.
Welcome to Electrolux.

Visit our website to:

Get usage advice, brochures, trouble shooter, service and repair information:

www.electrolux.com/support

Register your product for better service:

www.registerelectrolux.com

Buy Accessories, Consumables and Original spare parts for your appliance:

www.electrolux.com/shop

CUSTOMER CARE AND SERVICE

Always use original spare parts.
When contacting our Authorised Service Centre, ensure that you have the following data
available: Model, PNC, Serial Number.
The information can be found on the rating plate.

Warning / Caution-Safety information
General information and tips
Environmental information

Subject to change without notice.

CONTENTS

1. SAFETY INFORMATION................................................................................ 4

2. SAFETY INSTRUCTIONS.............................................................................. 5

3. INSTALLATION...............................................................................................7

4. PRODUCT DESCRIPTION............................................................................. 9

5. CONTROL PANEL........................................................................................ 10

6. PROGRAMME SELECTION......................................................................... 11

7. BASIC SETTINGS ........................................................................................13

8. WIRELESS CONNECTION...........................................................................17

9. BEFORE FIRST USE....................................................................................19

10. DAILY USE..................................................................................................20

11. HINTS AND TIPS........................................................................................ 23

12. CARE AND CLEANING.............................................................................. 24

13. TROUBLESHOOTING................................................................................ 28

14. TECHNICAL INFORMATION......................................................................33

15. ENVIRONMENTAL CONCERNS................................................................34

2 ENGLISH

My Electrolux Kitchen app

ENGLISH 3

1. SAFETY INFORMATION

Before the installation and use of the appliance, carefully read
the supplied instructions. The manufacturer is not responsible
for any injuries or damage that are the result of incorrect
installation or usage. Always keep the instructions in a safe
and accessible location for future reference.

1.1 Children and vulnerable people safety

• This appliance can be used by children aged from 8 years
and above and persons with reduced physical, sensory or
mental capabilities or lack of experience and knowledge if
they have been given supervision or instruction concerning
the use of the appliance in a safe way and understand the
hazards involved.

• Children between 3 and 8 years of age and persons with
very extensive and complex disabilities shall be kept away
from the appliance unless continuously supervised.

• Children of less than 3 years of age should be kept away
from the appliance unless continuously supervised.

• Children should be supervised to ensure that they do not
play with the appliance.

• Keep detergents away from children.

• Keep children and pets away from the appliance when the
door is open.

• Children shall not carry out cleaning and user maintenance
of the appliance without supervision.

1.2 General Safety

• This appliance is for cleaning household-type dishes and
tableware only.

• This appliance is designed for single household domestic
use in an indoor environment.

• This appliance may be used in offices, hotel guest rooms,
bed & breakfast guest rooms, farm guest houses and other

4 ENGLISH

similar accommodation where such use does not exceed
(average) domestic usage levels.

• Do not change the specification of this appliance.

• The operating water pressure (minimum and maximum)
must be between 0.05 (0.5) / 1 (10) MPa (bar).

• Follow the maximum number of 15 place settings.

• The appliance door should not be left in an open position to
avoid the tripping hazard.

• If the supply cord is damaged, it must be replaced by the
manufacturer, its Authorised Service Centre or similarly
qualified persons in order to avoid a hazard.

• WARNING: Knives and other utensils with sharp points
must be loaded in the basket with their points down or
placed in a horizontal position.

• Before any maintenance operation, deactivate the
appliance and disconnect the mains plug from the socket.

• Do not use high pressure water sprays and/or steam to
clean the appliance.

• If the appliance has ventilation openings in the base, they
must not be covered e.g. by a carpet.

• The appliance is to be connected to the water mains using
the new supplied hose-sets. Old hose sets must not be
reused.

2. SAFETY INSTRUCTIONS

2.1 Installation

WARNING!

Only a qualified person must install this
appliance.

• Remove all the packaging.

• Do not install or use a damaged
appliance.

• Follow the installation instructions supplied
with the appliance.

• Always take care when moving the
appliance as it is heavy. Always use safety
gloves and enclosed footwear.

• Do not install or use the appliance where
the temperature is less than 0 °C.

• Install the appliance in a safe and suitable
place that meets installation requirements.

• Do not use the appliance before installing
it in the built-in structure due to safety
manner.

2.2 Electrical connection

WARNING!

Risk of fire and electric shock.

ENGLISH 5

• Warning: this appliance is designed to be
installed / connected to a grounding
connection in the building.

• Make sure that the parameters on the
rating plate are compatible with the
electrical ratings of the mains power
supply.

• Always use a correctly installed
shockproof socket.

• Do not use multi-plug adapters and
extension cables.

• Make sure not to cause damage to the
mains plug and to the mains cable. Should
the mains cable need to be replaced, this
must be carried out by our Authorised
Service Centre.

• Connect the mains plug to the mains
socket only at the end of the installation.
Make sure that there is access to the
mains plug after the installation.

• Do not pull the mains cable to disconnect
the appliance. Always pull the mains plug.

2.3 Water connection

• Do not cause damage to the water hoses.

• Before connection to new pipes, pipes not
used for a long time, where repair work
has been carried out or new devices fitted
(water meters, etc.), let the water flow until
it is clean and clear.

• Ensure that there are no visible water
leaks during and after the first use of the
appliance.

• If the water inlet hose is damaged,
immediately close the water tap and
disconnect the mains plug from the mains
socket. Contact the Authorised Service
Centre to replace the water inlet hose.

• Without electrical power, the water
protection system is not active. In this
case there is a risk of flooding.

• The water inlet hose has a safety valve
and a sheath with an inner mains cable.

WARNING!

Dangerous voltage.

2.4 Use

• Do not put flammable products or items
that are wet with flammable products in,
near or on the appliance.

• Dishwasher detergents are dangerous.
Follow the safety instructions on the
detergent packaging.

• Do not drink and play with the water in the
appliance.

• Do not remove the dishes from the
appliance until the programme is
complete. Some detergent may remain on
the dishes.

• Do not store items or apply pressure on
the open door of the appliance.

• The appliance can release hot steam if
you open the door while a programme
operates.

2.5 Internal lighting

WARNING!

Risk of injury.

• This appliance has an internal lamp that
comes on when you open the door and
goes off when the door is closed.

• To replace the internal lighting, contact the
Authorised Service Centre.

6 ENGLISH

2.6 Service

• To repair the appliance contact the
Authorised Service Centre. Use original
spare parts only.

• Please note that self-repair or non­professional repair can have safety

consequences and might void the

www.youtube.com/electrolux
www.youtube.com/aeg

How to install your AEG/Electrolux

60 cm Sliding Door Dishwasher

min. 550

guarantee.

• The following spare parts will be available
for 7 years after the model has been
discontinued: motor, circulation and drain
pump, heaters and heating elements,
including heat pumps, piping and related
equipment including hoses, valves, filters
and aquastops, structural and interior
parts related to door assemblies, printed
circuit boards, electronic displays,
pressure switches, thermostats and
sensors, software and firmware including
reset software. Please note that some of
these spare parts are only available to
professional repairers, and that not all
spare parts are relevant for all models.

• The following spare parts will be available
for 10 years after the model has been
discontinued: door hinge and seals, other
seals, spray arms, drain filters, interior
racks and plastic peripherals such as
baskets and lids.

3. INSTALLATION

WARNING!

Refer to Safety chapters.

• Concerning the lamp(s) inside this product
and spare part lamps sold separately:
These lamps are intended to withstand
extreme physical conditions in household
appliances, such as temperature,
vibration, humidity, or are intended to
signal information about the operational
status of the appliance. They are not
intended to be used in other applications
and are not suitable for household room
illumination.

2.7 Disposal

WARNING!

Risk of injury or suffocation.

• Disconnect the appliance from the mains
supply.

• Cut off the mains cable and discard it.

• Remove the door catch to prevent children
and pets to get closed in the appliance.

3.1 Building in

3.2 Safety caps

If the furniture panel is not installed, open the
appliance door carefully to avoid the risk of
injury.

After installation, make sure the plastic
covers are locked in position. Damage or
removal of the plastic covers on the sides of
the door may impact the functionality of the

ENGLISH 7

appliance and may cause an injury. If the

max
5 mm

plastic cover is damaged, contact the
Authorized Service Centre to replace it with
the new one.

8 ENGLISH

4. PRODUCT DESCRIPTION

5

4

10

9

67

11

12

2

3

1

8

Ceiling spray arm

1

Upper spray arm

2

Lower spray arm

3

Filters

4

Rating plate

5

Salt container

6

Air vent

7

4.1 QR code on the rating plate

The rating plate has a QR code that can be
used in two ways.

Scan the QR code with the camera on your
mobile device to be redirected to My
Electrolux Kitchen app in the app store.
Follow the instructions on your mobile device
to download the app.

Scan the QR code with the scanner in My
Electrolux Kitchen app to pair the dishwasher
with your mobile device.

Rinse aid dispenser

8

Detergent dispenser

9

Lower basket

10

Upper basket

11

Cutlery drawer

12

4.2 Internal light

The appliance has an internal lamp. It comes
on when you open the door or switch the
appliance on while the door is open.

The lamp goes off when you close the door or
switch the appliance off. Otherwise, it goes
off automatically after some time to save
energy.

ENGLISH 9

5. CONTROL PANEL

1 2 3

4 5 6

ECO

On/Off button / Reset button

1

Delay start button / Remote start button

2

Display

3

MY TIME program selection bar

4

5.1 Display

The display shows the following information:

• ECOMETER

• Indicators

• Programme names and durations

• Delay start time

• Information texts

5.2 ECOMETER

5.3 Indicators

Indicator Description

Rinse aid indicator. It is on when the rinse aid dispenser needs refilling. Refer to "Before first
use".

Salt indicator. It is on when the salt container needs refilling. Refer to "Before first use".

Option buttons (EXTRAS)

5

AUTO Sense program button

6

The ECOMETER indicates how the
programme selection impacts energy and
water consumption. The more bars are on,
the lower the consumption is.

indicates the most environmentally
friendly programme selection for a normally
soiled dishwashing load.

10 ENGLISH

Machine Care indicator. It is on when the appliance needs internal cleaning with the Machine
Care programme. Refer to "Care and cleaning".

Drying phase indicator. It is on when you select a programme with the drying phase. It flash‐
es when the drying phase operates. Refer to "Programme selection".

Wi-Fi indicator. It is on when you activate the wireless connection. Refer to "Wireless con‐
nection".

Remote start indicator. It is on when you activate the remote start. Refer to "Daily use".

Indicator Description

CA B D E

Delay Start indicator. It is on when you set the delay start. Refer to "Daily use".

Pause indicator. It flashes when you pause a wash cycle or the delay countdown by opening
the appliance door. Refer to "Daily use".

Alert indicators. They are on when a malfunction of the appliance occurs. Refer to "Trouble‐

shooting".

6. PROGRAMME SELECTION

6.1 MY TIME

MY TIME selection bar allows to select a
suitable dishwashing cycle based on
programme duration.

A. • Quick is the shortest programme

(30min) suitable for dishwashing a
load with fresh and light soil.

• Pre-rinse (15min) is a
programme for rinsing off food
remains from the dishes. It prevents
odours forming in the appliance. Do
not use detergent with this
programme.

B. 1h is a programme suitable for

dishwashing a load with fresh and lightly
dried-on soil.

C. 1h 30min is a programme suitable for

dishwashing and drying normally soiled
items.

D. 2h 40min is a programme suitable for

dishwashing and drying heavily soiled
items.

E. ECO is the longest programme offering

the most efficient use of energy and water
consumption for crockery and cutlery with
normal soil. This is the standard

programme for test institutes.

1)

6.2 AUTO Sense

The AUTO Sense programme automatically
adjusts the dishwashing cycle to the type of
load.

The appliance senses the degree of soil and
the amount of dishes in the baskets. It adjusts
the temperature and quantity of water as well
as the wash duration.

6.3 EXTRAS

You can adjust the programme selection to
your needs by activating EXTRAS.

SprayZone

SprayZone improves the dishwashing
results by increasing the pressure and
temperature of the water as well as wash
time. The option operates within the
designated area in the lower basket.
SprayZone is suitable for dishwashing items
with stubborn soil, e.g. pots, pans and
casserole dishes.

CAUTION!

Make sure that the items placed in the
SprayZone area do not block the upper
spray arm.

ExtraPower

ExtraPower improves the dishwashing
results of the selected programme. The
option increases the wash temperature and
duration.

1)

This programme is used to assess compliance with the Ecodesign Comission Regulation (EU) 2019/2022.

ENGLISH 11

GlassCare

GlassCare prevents delicate load,
glassware in particular, from damaging. The
option prevents rapid changes in the
dishwashing temperature of the selected
programme and reduces it to 45 °C.

6.5 Programmes overview

6.4 Extras in the app

My Electrolux Kitchen app provides additional
dishwashing options. To access all options,
connect your dishwasher to the app. See
chapter "Wireless connection".

Programme Dishwasher

load

Quick Crockery, cutlery Fresh

All All

Pre-rinse

1h Crockery, cutlery Fresh, lightly

1h 30min Crockery, cut‐

lery, pots, pans

2h 40min Crockery, cut‐

lery, pots, pans

ECO Crockery, cut‐

lery, pots, pans

Degree of
soil

dried-on

Normal, lightly
dried-on

Normal to
heavy, dried-on

Normal, lightly
dried-on

Programme phases EXTRAS

• Dishwashing 50 °C

• Intermediate rinse

• Final rinse 45 °C

• AirDry

• Prewash

• Dishwashing 60 °C

• Intermediate rinse

• Final rinse 50 °C

• AirDry

• Dishwashing 60 °C

• Intermediate rinse

• Final rinse 55 °C

• Drying

• AirDry

• Prewash

• Dishwashing 60 °C

• Intermediate rinse

• Final rinse 60 °C

• Drying

• AirDry

• Prewash

• Dishwashing 50 °C

• Intermediate rinse

• Final rinse 55 °C

• Drying

• AirDry

1)

1)

1)

1)

1)

• ExtraPower

• GlassCare

• SprayZone

• ExtraHygiene

Not applicable

• ExtraPower

• GlassCare

• SprayZone

• ExtraHygiene

• ExtraPower

• GlassCare

• SprayZone

• ExtraHygiene

• ExtraPower

• GlassCare

• SprayZone

• ExtraHygiene

• ExtraPower

• GlassCare

• SprayZone

• ExtraHygiene

• ExtraSilent

2)

2)

2)

2)

2)

2)

12 ENGLISH

Programme Dishwasher

load

AUTO Sense Crockery, cut‐

Machine Care For cleaning the appliance interior.

1)

Automatic door opening during the drying phase. Refer to "Basic settings".

2)

Available only through My Electrolux Kitchen app.

lery, pots, pans

Refer to "Care and Cleaning".

Degree of
soil

All

Programme phases EXTRAS

• Prewash

• Dishwashing 50 - 60 °C

• Intermediate rinse

• Final rinse 60 °C

• Drying

• AirDry

• Cleaning 70 °C

• Intermediate rinse

• Final rinse

• AirDry

1)

1)

Consumption values

Not applicable

Not applicable

Programme

1)

The pressure and the temperature of the water, the variations of the mains supply, the options, the quantity of
dishes and the degree of soil can change the values.

2)

The values for programmes other than ECO are indicative only.

1)2)

Quick 10.9 0.610 30

Pre-rinse 4.6 0.010 15

1h 11.8 0.880 60

1h 30min 11.9 0.970 90

2h 40min 12.2 1.140 160

ECO 11.0 0.860 240

AUTO Sense 12.2 1.140 170

Machine Care 10.5 0.590 60

Information for test institutes

To receive the necessary information for
conducting performance tests (e.g. according
to: EN60436 ), send an email to:

Water (l) Energy (kWh) Duration (min)

In your request, include the product number
code (PNC) from the rating plate.

For any other questions regarding your
dishwasher, refer to the service book
provided with your appliance.

[email protected]

7. BASIC SETTINGS

You can configure the appliance by changing basic settings according to your needs.

ENGLISH 13

Settings Values Description

BA C

Water hardness 1 - 10 (default: 5) Adjust the level of the water softener according to the

water hardness in your area.

Rinse aid level 0 - 6 (default: 4) Adjust the level of the rinse aid according to the neces‐

sary dosage.

End sound ON

Auto door open ON (default)

Key tones ON (default)

Latest prog. selection ON

Display on floor ON (default)

Brightness 0 - 9 Adjust the brightness of the display.

Language List of languages (default:

Reset settings YES

WiFi ON

Network Signal strength

Forget network YES

PNC number Number

1)

For more details, refer to the information provided in this chapter.

2)

For more details, refer to the chapter "Wireless connection".

OFF (default)

OFF

OFF

OFF (default)

OFF

English)

NO

OFF (default)

IP
MAC

NO

Activate or deactivate the acoustic signal for the end of a

programme.

Activate or deactivate AirDry.

Activate or deactivate the sound of the buttons when
pressed.

Enable or disable the automatic selection of the most re‐

cently used programme and options.

Activate or deactivate TimeBeam.

Set the preferred language.

Reset the appliance to the factory settings. The setting
does not reset the wireless connection setup.

Activate or deactivate the wireless connection.

Check the information about the network connection.

Reset the network credentials.

Check the PNC number of your appliance.

1)

1)

1)

1)

1)

1)

2)

2)

1)

7.1 Setting mode

How to navigate in setting mode

You can navigate in setting mode using
MY TIME selection bar.

14 ENGLISH

A. Previous button
B. OK button
C. Next button

Use Previous and Next to switch between
the basic settings and to change their value.

Use OK to enter the selected setting and to
confirm changing its value.

How to enter setting mode

You can enter setting mode before starting a
programme. You cannot enter setting mode
while the programme is running.

To enter setting mode, press and hold

simultaneously

and for about 3

seconds.

• The lights related to the Previous, OK
and Next are on.

• The display shows the first available
setting and its current value.

How to change a setting

Make sure the appliance is in setting mode.

1. Use Previous or Next to select the
desired setting.

The display shows the setting name and its
current value.

2. Press OK to enter the setting.

The display shows available values.

3. Press Previous or Next to change the
value.

4. Press OK to confirm the setting.

• The new setting is saved.

• The appliance returns to the basic
settings list.

5. Press and hold simultaneously

and for about 3 seconds to exit

setting mode.

The appliance returns to the programme
selection.
The saved settings remain valid until you
change them again.

7.2 The water softener

The water softener removes minerals from
the water supply, which would have a
negative effect on the washing results and on
the appliance.

The higher the content of these minerals, the
harder your water is. Water hardness is
measured in equivalent scales.

The water softener should be adjusted
according to the hardness of the water in your
area. Your local water authority can advise
you on the hardness of the water in your
area. Set the right level of the water softener
to assure good washing results.

Water hardness

German de‐

grees (°dH)

47 - 50 84 - 90 8.4 - 9.0 835 - 904 58 - 63 10

43 - 46 76 - 83 7.6 - 8.3 755 - 834 53 - 57 9

37 - 42 65 - 75 6.5 - 7.5 645 - 754 46 - 52 8

29 - 36 51 - 64 5.1 - 6.4 505 - 644 36 - 45 7

23 - 28 40 - 50 4.0 - 5.0 395 - 504 28 - 35 6

19 - 22 33 - 39 3.3 - 3.9 325 - 394 23 - 27

15 - 18 26 - 32 2.6 - 3.2 255 - 324 18 - 22 4

11 - 14 19 - 25 1.9 - 2.5 185 - 254 13 - 17 3

4 - 10 7 - 18 0.7 - 1.8 70 - 184 5 - 12 2

<4 <7 <0.7 <70 < 5

1)

Factory setting.

2)

Do not use salt at this level.

French de‐
grees (°fH)

mmol/l mg/l (ppm) Clarke de‐

grees

Water softener

level

1)

5

2)

1

ENGLISH 15

Regardless of the type of detergent used,
set the proper water hardness level to
keep the salt refill indicator active.

Multi-tabs containing salt are not effective
enough to soften hard water.

Regeneration process

For the correct water softener operation, the
resin of the softener device needs to be
regenerated regularly. This process is
automatic and is the part of the normal
dishwasher operation.

When the prescribed quantity of water (see
values in the table) has been used since the
previous regeneration process, a new
regeneration process will be initiated between
the final rinse and the programme end.

Water softener level Amount of water (l)

1 250

2 100

3 62

4 47

5 25

6 17

7 10

8 5

9 3

10 3

In case of the high water softener setting, it
may occur also in the middle of the
programme, before the rinse (twice during a
programme). Regeneration initiation has no
impact on the cycle duration, unless it occurs
in the middle of a programme or at the end of
a programme with a short drying phase. In
such cases, the regeneration prolongs the
total duration of a programme by additional 5
minutes.

Subsequently, the rinsing of the water
softener that lasts 5 minutes may begin in the
same cycle or at the beginning of the next
programme. This activity increases the total
water consumption of a programme by

additional 4 litres and the total energy
consumption of a programme by additional 2
Wh. The rinsing of the softener ends with a
complete drain.

Each performed softener rinse (possible more
than one in the same cycle) may prolong the
programme duration by another 5 minutes
when it occurs at any point at the beginning
or in the middle of a programme.

All the consumption values mentioned in
this section are determined in line with
the currently applicable standard in
laboratory conditions with water hardness

2.5mmol/L (water softener: level 3)
according to the regulation: 2019/2022 .
The pressure and the temperature of
water as well as the variations of the
mains supply can change the values.

7.3 Rinse aid level

The rinse aid helps to dry the dishes without
streaks and stains. It is automatically
released during the hot rinse phase. It is
possible to set the released quantity of rinse
aid.

When the rinse aid dispenser is empty, the

display shows the indicator

and Rinse aid
low. If the drying results are satisfactory while
using multi-tablets only, it is possible to
deactivate the dispenser and the refill
notification. However, for best drying
performance, always use rinse aid and keep
the notification active.

To deactivate the rinse aid dispenser and the
notification, set the rinse aid level to 0.

7.4 End sound

You can activate an acoustic signal that
sounds when the programme is completed.

Acoustic signals sound also when a
malfunction of the appliance occurs. It is
not possible to deactivate these signals.

16 ENGLISH

7.5 AirDry

AirDry improves the drying results. The
appliance door opens automatically during
the drying phase and remains ajar.

is then selected automatically after you
activate the appliance.

When the latest programme selection is
disabled, the default programme is ECO.

7.7 TimeBeam

AirDry is automatically activated with all
programmes other than Pre-rinse.

The duration of the drying phase and the door
opening time vary depending on the selected
programme and options.

When AirDry opens the door, the display
shows the remaining time of the running
programme.

CAUTION!

Do not try to close the appliance door
within 2 minutes after automatic opening.
This can cause damage to the appliance.

CAUTION!

If children have access to the appliance,
we advise to deactivate AirDry. The
automatic opening of the door may pose
a danger.

7.6 Latest programme selection

You can set the automatic selection of the
most recently used programme and options.

The latest programme that was completed
before the appliance deactivation is saved. It

8. WIRELESS CONNECTION

TimeBeam displays the following information
on the floor below the appliance door:

• The programme duration when the

programme begins.

• 0:00 and CLEAN when the programme is

completed.

• DELAY and the countdown duration when

the delay start begins.

• An alarm code when the appliance has a

malfunction.

When AirDry opens the door, TimeBeam
is off. To check the remaining time of the
running programme, look at the control
panel display.

7.8 PNC number

If you contact an Authorised Service Centre,
you need to provide the product number code
(PNC number) of your appliance.

The number can be found on the rating plate
on the appliance door. You can also check
the number on the display. Select PNC
number from the setting list to check the
number.

You can connect your dishwasher to the
home wireless network and then link it to your
mobile devices in My Electrolux Kitchen app.

This functionality allows you to remotely
control and monitor your dishwasher.

ENGLISH 17

My Electrolux Kitchen app is available for
download from the app store on your mobile
device. You can scan the QR code from the
rating plate to be redirected to the app (see
chapter "Product description").

The app is compatible with iOS and Android
operating systems. Check the compatible
versions of the operating systems in the app
store.

Wi-Fi module parameters

Wi-Fi module NIUS-SA

Frequency 2.412 - 2.472 GHz

Protocol IEEE 802.11 b-g-n

Max Power <20 dBm

Encryption WPA, WPA2

If the connection is successful, the
dishwasher displays Connection
successful. Refer to "Daily use" chapter to
activate remote start.

If the connection is unsuccessful or the
display shows Updating, refer to
"Troubleshooting".

If you want to cancel the procedure, press
any active button and confirm the
cancellation. Alternatively, deactivate and
activate the appliance.

8.2 How to deactivate the wireless connection

Enter setting mode, select the setting WiFi
and change its value to OFF.

8.1 How to connect the dishwasher to the network and to the app

To connect your dishwasher, you need:

• Wireless network with the Internet
connection.

• Mobile device connected to the wireless
network.

1. Launch My Electrolux Kitchen app on

your mobile device and follow the
instructions in the app. When prompted in
the app, activate the wireless connection
in the dishwasher.

2. To activate the wireless connection,

follow one of the two methods:

• Press and hold simultaneously

for 2 seconds.

• Enter setting mode, select the setting
WiFi and change its values to ON.

The display shows Wi-Fi is starting up and
then Wi-Fi is ready.

3. When prompted, enter the home network
credentials in My Electrolux Kitchen app.

If the credentials are not entered, the
dishwasher deactivates the wireless
connection after some time.

and

8.3 How to activate the wireless connection

Enter setting mode, select the setting WiFi
and change its value to ON.

Refer to "Daily use" to activate the remote
start.

8.4 How to reset the network credentials

If you want to connect to a different wireless
network or update the credentials of the
current network, reset the network
credentials.

Enter setting mode and activate the setting
Forget network.

The indicator is off.
Connect the dishwasher to the network and
to the app to enter new network credentials.
Refer to the instructions provided earlier in
this chapter.

18 ENGLISH

9. BEFORE FIRST USE

A

B

C

1. Make sure that the current level of the
water softener agrees with the
hardness of the water supply. If not,
adjust the level of the water softener.

2. Fill the salt container.

3. Fill the rinse aid dispenser.

4. Open the water tap.

5. Start the programme Quick to remove

any residuals from the manufacturing
process. Do not use detergent and do not
put dishes in the baskets.

After starting the programme, the appliance
recharges the resin in the water softener for
up to 5 minutes. The washing phase starts
only after this procedure is complete. The
procedure is repeated periodically.

9.1 The salt container

CAUTION!

Use only regeneration salt for
dishwashers. Do not use kitchen salt.

The salt is used to recharge the resin in the
water softener and to assure good washing
results in daily use.

How to fill the salt container

1. Turn the cap of the salt container
counterclockwise and remove it.

2. Put 1 litre of water in the salt container
(only for the first time).

3. Fill the salt container with dishwasher salt
(until it is full).

5. Remove the salt around the opening of
the salt container.

6. Turn the cap clockwise to close the salt
container.

CAUTION!

Water and salt can come out of the salt
container when you fill it. To prevent
corrosion, fill the salt container and then
immediately start a complete
dishwashing cycle with detergent.

9.2 How to fill the rinse aid

dispenser

4. Carefully shake the funnel by its handle to

get the last granules inside.

CAUTION!

The compartment (B) is for rinse aid only.
Do not fill it with detergent.

CAUTION!

Only use rinse aid designed specifically
for dishwashers.

ENGLISH 19

1. Open the lid (C).

A

B

C

2. Fill the dispenser (B) until the rinse aid
reaches the marking ''MAX''.

3. Remove the spilled rinse aid with an
absorbent cloth to prevent excessive
foam formation.

4. Close the lid. Make sure that the lid locks
into position.

10. DAILY USE

1. Open the water tap.

2. Press and hold until the appliance is

activated.

3. Fill the salt container if it is empty.

4. Fill the rinse aid dispenser if it is empty.

5. Load the baskets.

6. Add the detergent.

7. Select and start a programme.

8. Close the water tap when the programme

is complete.

10.1 Using the detergent

Fill the rinse aid dispenser when the
indicator (A) is clear.

For information about the detergent
dosage, refer to the manufacturer's
instructions on the packaging of the
product. Usually, 20 - 25 ml of gel
detergent is adequate for washing a load
with normal soil.

The upper ends of the two vertical ribs
inside the compartment (B) indicate the
maximum level for filling the dispenser
with gel (max. 30ml).

10.2 Remote start

Activate this function to remotely control and
monitor your dishwasher in My Electrolux
Kitchen app.

CAUTION!

Only use detergent specifically designed
for dishwashers.

1. Press the release button (A) to open the
lid (C).

2. Put the detergent (gel, powder or tablets)
in the compartment (B).

3. If the programme has a prewash phase,
put a small quantity of detergent on the
inner part of the appliance door.

4. Close the lid. Make sure that the lid locks
into position.

20 ENGLISH

How to activate the remote start

Make sure that the indicator is on and
your dishwasher is added in My Electrolux
Kitchen app. If not, refer to "Wireless

connection".

1. Press .

• The light related to the button is on.

• The indicator is off.

• The indicator is on.

2. Close the appliance door.

3. Use My Electrolux Kitchen app to

remotely operate the appliance.

Opening the door deactivates the remote
start. Refer to the information provided
further in this chapter.

• The display shows the updated
programme duration.

• The ECOMETER indicates the
updated level of energy and water
consumption.

How to deactivate the remote start

Press until the display shows 0h.

• The light related to the button is off.

• The indicator is off.

• The indicator

• The appliance returns to the
programme selection.

is on.

10.3 How to select and start a programme using MY TIME selection bar

1. Slide your finger across MY TIME

selection bar to choose a suitable
programme.

• The light related to the selected
programme is on.

• The ECOMETER indicates the level of
energy and water consumption.

• The display shows the programme
duration.

2. Activate applicable EXTRAS if desired.

3. Close the appliance door to start the

programme.

10.4 How to select and start the programme Pre-rinse

1. To select Pre-rinse, press and hold

for 3 seconds.

• The light related to the button is on.

• The ECOMETER is off.

• The display shows the programme
name and duration.

2. Close the appliance door to start the
programme.

10.5 How to activate EXTRAS

1. Select a programme using MY TIME

selection bar.

2. Press the button dedicated to the option
you want to activate.

• The light related to the button is on.

By default, options must be activated
every time before you start a programme.
If the latest programme selection is
enabled, the saved options are activated
automatically along with the programme.

It is not possible to activate or deactivate
options while a programme is running.

Not all options are compatible with each
other.

Activating options often increases the
water and energy consumption as well as
the programme duration.

10.6 How to start the AUTO Sense program

1. Press .

• The light related to the button is on.

• The display shows the longest
possible program duration.

2. Close the appliance door to start the
program.

The appliance senses the type of load and
adjusts a suitable wash cycle. During the
cycle, the sensors operate several times and
the initial program duration can decrease.

10.7 How to delay the start of a

programme

1. Select a programme.

2. Double press .

The display shows 1h.

3. Press repeatedly until the display

shows the desired delay time (from 1 to
24 hours).

ENGLISH 21

4. Close the appliance door to start the

countdown.

When you set the delay start, the remote start
is automatically activated.

During the countdown, you cannot change
the programme selection. You can change
the delay time in the app.

When the countdown is complete, the
programme starts.

10.8 Opening the door while the appliance operates

Opening the door while a programme is
running pauses the wash cycle. The display
shows the remaining duration of the
programme. The programme bar at the
bottom of the display indicates the current
progress of the wash cycle. The length of the
bar decreases along with the programme
duration. After closing the door, the wash
cycle resumes from the point of interruption.

Opening the door while the remote start is
activated deactivates this function. Activate
the remote start again before you close the
door; otherwise, the wash cycle starts
immediately after you close the door.
Opening the door does not deactivate the
remote start if the delay start is set.

If you open the door during the delay start
countdown, the countdown is paused. The
display shows the current countdown status.
After closing the door, the countdown
resumes.

Opening the door while the appliance
operates may affect the energy
consumption and the programme
duration.

10.9 How to cancel the delay start while the countdown operates

Press and hold for about 3 seconds.

The appliance returns to the programme
selection.

If you cancel the delay start, you have to
select the programme again.

10.10 How to cancel a running programme

Press and hold for about 3 seconds.

The appliance returns to the programme
selection.

Make sure that there is detergent in the
detergent dispenser before you start a
new programme.

10.11 The Auto Off function

This function saves energy by switching the
appliance off when it is not operating.

The function comes into operation
automatically:

• When the programme is completed.

• After 5 minutes if a programme was not
started.

10.12 End of the programme

When the programme is complete, the
display shows Dishes clean.

The Auto Off function switches the appliance
off automatically.

All buttons are inactive except for the on/off
button.

If the door is opened for more than 30
seconds during the drying phase, the
running programme ends. It does not
happen if the door is opened by the
AirDry function.

22 ENGLISH

If the display shows Updating, refer to
"Troubleshooting".

11. HINTS AND TIPS

11.1 General

Follow the hints below to ensure optimal
cleaning and drying results in daily use and to
protect the environment.

• Washing dishes in the dishwasher as
instructed in the user manual usually
consumes less water and energy than
washing dishes by hand.

• Load the dishwasher to its full capacity to
save water and energy. For best cleaning
results, arrange items in the baskets as
instructed in the user manual and do not
overload the baskets.

• Do not pre-rinse dishes by hand. It
increases the water and energy
consumption. When needed, select a
programme with a prewash phase.

• Remove larger residues of food from the
dishes and empty cups and glasses
before putting them inside the appliance.

• Soak or slightly scour cookware with firmly
cooked-on or baked-on food before
washing it in the appliance.

• Make sure that items in the baskets do not
touch or cover each other. Only then can
the water completely reach and wash the
dishes.

• You can use dishwasher detergent, rinse
aid and salt separately or you can use the
multi-tablets (e.g. ''All in 1''). Follow the
instructions on the packaging.

• Select a programme according to the type
of load and the degree of soil. ECO offers
the most efficient use of water and energy
consumption.

• To prevent limescale buildup inside the
appliance:

– Refill the salt container whenever

necessary.

– Use the recommended dosage of the

detergent and rinse aid.

– Make sure that the current level of the

water softener agrees with the
hardness of the water supply.

– Follow the instructions in the chapter

"Care and cleaning".

11.2 Using salt, rinse aid and detergent

• Only use salt, rinse aid and detergent
designed for dishwasher. Other products
can cause damage to the appliance.

• In areas with hard and very hard water, we
recommend to use basic dishwasher
detergent (powder, gel, tablets containing
no additional agents), rinse aid and salt
separately for optimal cleaning and drying
results.

• Detergent tablets do not fully dissolve with
short programmes. To prevent detergent
residues on the tableware, we recommend
that you use tablets with long
programmes.

• Always use the correct quantity of
detergent. Insufficient dosage of detergent
can result in poor cleaning results and
hard-water filming or spotting on the items.
Using too much detergent with soft or
softened water results in detergent
residues on the dishes. Adjust the amount
of detergent based on the water hardness.
Refer to the instructions on the detergent
packaging.

• Always use the correct quantity of rinse
aid. Insufficient dosage of rinse aid
decreases the drying results. Using too
much rinse aid results in bluish layers on
the items.

• Make sure that the water softener level is
correct. If the level is too high, the
increased quantity of salt in the water
might result in rust on cutlery.

11.3 What to do if you want to stop

using multi-tablets

Before you start using separately detergent,
salt and rinse aid, complete the following
steps:

1. Set the highest level of the water

softener.

2. Make sure that the salt and rinse aid

containers are full.

3. Start the Quick programme. Do not add

detergent and do not put dishes in the
baskets.

ENGLISH 23

4. When the programme is completed,

adjust the water softener according to the
water hardness in your area.

5. Adjust the released quantity of rinse aid.

11.4 Before starting a programme

Before you start the selected programme,
make sure that:

• The filters are clean and correctly
installed.

• The cap of the salt container is tight.

• The spray arms are not clogged.

• There is enough salt and rinse aid (unless
you use multi-tablets).

• The arrangement of the items in the
baskets is correct.

• The programme is suitable to the type of
load and the degree of soil.

• The correct quantity of detergent is used.

11.5 Loading the baskets

• Always use the whole space of the
baskets.

• Use the appliance to wash dishwasher­safe items only.

• Do not wash in the appliance items made
of wood, horn, aluminium, pewter and
copper as they could crack, warp, get
discoloured or pitted.

• Do not wash in the appliance items that
can absorb water (sponges, household
cloths).

• Put hollow items (cups, glasses and pans)
with the opening facing downwards.

• Make sure that glass items do not touch
each other.

• Put light items in the upper basket. Make
sure that the items do not move freely.

• Put cutlery and small items in the cutlery
drawer.

• Move the upper basket upwards to
accommodate large items in the lower
basket.

• Make sure that the spray arms can move
freely before you start a programme.

11.6 Unloading the baskets

1. Let the tableware cool down before you

remove it from the appliance. Hot items
can be easily damaged.

2. First remove items from the lower basket,

then from the upper basket.

After the programme is completed, water
can still remain on the inside surfaces of
the appliance.

12. CARE AND CLEANING

WARNING!

Before any maintenance other than
running the programme Machine Care,
deactivate the appliance and disconnect
the mains plug from the main socket.

Dirty filters and clogged spray arms
negatively affect the washing results.
Check these elements regularly and, if
necessary, clean them.

12.1 Machine Care

Machine Care is a programme designed to
clean the appliance interior with optimal
results. It removes limescale and grease
buildup.

24 ENGLISH

When the appliance senses the need for
cleaning, the display shows the reminder
message Please run MachineCare and the

indicator . Start the Machine Care
programme to clean the appliance interior.

How to start the Machine Care programme

Before starting the Machine Care
programme, clean the filters and spray
arms.

1. Use a descaler or a cleaning product

designed specifically for dishwashers.
Follow the instructions on the packaging.
Do not put dishes in the baskets.

2. Press and hold simultaneously and

C

B

A

for about 3 seconds.

The indicator flashes. The display shows
the programme duration.

3. Close the appliance door to start the
programme.

When the programme is complete, the
reminder message is disabled.

12.2 Internal cleaning

• Clean the appliance interior with a soft

damp cloth.

• Do not use abrasive products, abrasive

cleaning pads, sharp tools, strong
chemicals, scourer or solvents.

• Wipe clean the door, including the rubber

gasket, once a week.

• To maintain the performance of your

appliance, use a cleaning product
designed specifically for dishwashers at
least once every two months. Carefully
follow the instructions on the packaging of
the product.

• For optimal cleaning results, start the

programme Machine Care.

12.3 Removal of foreign objects

Check the filters and the sump after each use
of the dishwasher. Foreign objects (e.g.
pieces of glass, plastic, bones or toothpicks,
etc) decrease the cleaning performance and
can cause damage to the drain pump.

12.5 Cleaning the filters

The filter system is made of 3 parts.

1. Turn the filter (B) counterclockwise and
remove it.

CAUTION!

If unable to remove the foreign objects,
contact an Authorised Service Centre.

1. Disassemble the filters system as
instructed in this chapter.

2. Remove any foreign objects manually.

3. Reassemble the filters as instructed in

this chapter.

12.4 External cleaning

• Clean the appliance with a moist soft

cloth.

• Only use neutral detergents.

• Do not use abrasive products, abrasive

cleaning pads or solvents.

2. Remove the filter (C) out of filter (B).

3. Remove the flat filter (A).

4. Wash the filters.

ENGLISH 25

5. Make sure that there are no residues of

food or soil in or around the edge of the
sump.

6. Put back in place the flat filter (A). Make
sure that it is correctly positioned under
the 2 guides.

CAUTION!

An incorrect position of the filters can
cause bad washing results and damage
to the appliance.

12.6 Cleaning the lower spray arm

We recommend to clean the lower spray arm
regularly to prevent soil from clogging the
holes.

Clogged holes can cause unsatisfactory
washing results.

1. To remove the lower spray arm, pull it
upwards.

2. Wash the spray arm under running water.
Use a thin pointed tool, e.g. a toothpick,
to remove particles of soil from the holes.

7. Reassemble the filters (B) and (C).

8. Put back the filter (B) in the flat filter (A).

Turn it clockwise until it locks.

26 ENGLISH

3. To install the spray arm back, press it

downwards.

12.7 Cleaning the upper spray arm

C

B

A

We recommend to clean the upper spray arm
regularly to prevent soil from clogging the
holes.

Clogged holes can cause unsatisfactory
washing results.

1. Pull out the upper basket.

2. To detach the spray arm from the basket,

press the spray arm upwards and
simultaneously turn it clockwise.

4. To install the spray arm back, press the
spray arm upwards and simultaneously
turn it counterclockwise until it locks into
place.

12.8 Cleaning the ceiling spray arm

We recommend to clean the ceiling spray
arm regularly to prevent soil from clogging the
holes. Clogged holes can cause
unsatisfactory washing results.

The ceiling spray arm is placed on the ceiling
of the appliance. The spray arm (C) is
installed in the delivery tube (A) with the
mounting element (B).

3. Wash the spray arm under running water.
Use a thin pointed tool, e.g. a toothpick,
to remove particles of soil from the holes.

1. Release the stoppers on the sides of the
sliding rails of the cutlery drawer and pull
the drawer out.

ENGLISH 27

1

2

2. Move the upper basket to the lowest level
to reach the spray arm more easily.

3. To detach the spray arm (C) from the
delivery tube (A), turn the mounting
element (B) counterclockwise and pull the
spray arm downwards.

4. Wash the spray arm under running water.
Use a thin pointed tool, e.g. a toothpick,
to remove particles of soil from the holes.
Run the water through the holes to wash
soil particles away from the inside.

13. TROUBLESHOOTING

5. To install the spray arm (C) back, insert

the mounting element (B) in the spray
arm and fix it in the delivery tube (A) by
turning it clockwise. Make sure that the
mounting element locks into place.

6. Install the cutlery drawer on the sliding
rails and block the stoppers.

WARNING!

Improper repair of the appliance may
pose a danger to the safety of the user.
Any repairs must be performed by
qualified personnel.

The majority of problems that may occur
can be solved without the need to contact
an Authorised Service Centre.

Problem and alarm code Possible cause and solution

You cannot activate the appliance.

The programme does not start.

28 ENGLISH

• Make sure that the mains plug is connected to the mains socket.

• Make sure that there is no damaged fuse in the fuse box.

• Make sure that the appliance door is closed.

• If the delay start is set, cancel the setting or wait for the end of the
countdown.

• The appliance recharges the resin inside the water softener. The dura‐
tion of the procedure is approximately 5 minutes.

Refer to the below table for information on
possible problems.

With some problems, the display shows an
alarm code.

Problem and alarm code Possible cause and solution

The appliance does not fill with wa‐
ter.

The display shows , Error i10 or
Error i11 and No intake of water.

The appliance does not drain the
water.

The display shows , Error i20
and Water is not draining.

The anti-flood device is on.

The display shows , Error i30
and Risk of flood detected.

Malfunction of the water level detec‐
tion sensor.
The display shows i41 - i44.

Malfunction of the wash pump or the
drain pump.
The display shows i51 - i59 or i5A ­i5F.

The temperature of the water inside
the appliance is too high or malfunc‐
tion of the temperature sensor oc‐
curred.
The display shows i61 or i69.

Technical malfunction of the appli‐
ance.
The display shows iC0 or iC3.

The level of water inside the appli‐
ance is too high.
The display shows iF1.

Network unit error.
The display shows iC4 Network In‐

terface Error or iC5 Network Inter‐
face Error.

The appliance stops and starts
more times during operation.

The programme lasts too long.

The displayed programme duration
is different than the duration in the
consumption values table.

• Make sure that the water tap is open.

• Make sure that the pressure of the water supply is not too low. For this
information, contact your local water authority.

• Make sure that the water tap is not clogged.

• Make sure that the filter in the inlet hose is not clogged.

• Make sure that the inlet hose has no kinks or bends.

• Make sure that the sink spigot is not clogged.

• Make sure that the interior filter system is not clogged.

• Make sure that the drain hose has no kinks or bends.

• Close the water tap and contact an Authorised Service Centre.

• Make sure that the filters are clean.

• Switch the appliance off and on.

• Switch the appliance off and on.

• Make sure that the temperature of the inlet water does not exceed
60°C.

• Switch the appliance off and on.

• Switch the appliance off and on.

• Switch the appliance off and on.

• Make sure that the filters are clean.

• Make sure that the outlet hose is installed at the right height above the
floor. Refer to the installation instructions.

• Contact an Authorised Service Centre.

• It is normal. It provides optimal cleaning results and energy savings.

• If the delay start option is set, cancel the delay setting or wait for the
end of the countdown.

• Activating options often increases the programme duration.

• The pressure and the temperature of the water, the variations of the
mains supply, the options, the quantity of dishes and the degree of soil
can change the programme duration.

ENGLISH 29

Problem and alarm code Possible cause and solution

The remaining time in the display in‐
creases and skips nearly to the end
of the programme duration.

Small leak from the appliance door.

The appliance door is difficult to
close.

The appliance door opens during
the wash cycle.

Rattling or knocking sounds from
the inside of the appliance.

The appliance trips the circuit-beak‐
er.

The appliance is switched on but
does not operate.
The display shows Power Fail.

The appliance switches off during
operation.

The display shows Updating. All
buttons are inactive except for the
on/off.

• This is not a defect. The appliance is working correctly.

• The appliance is not levelled. Loosen or tighten the adjustable feet (if
applicable).

• The appliance door is not centred on the tub. Adjust the rear foot (if ap‐
plicable).

• The appliance is not levelled. Loosen or tighten the adjustable feet (if
applicable).

• Parts of the tableware are protruding from the baskets.

• The AirDry function is activated. You can deactivate the function. Refer
to "Basic settings".

• The tableware is not properly arranged in the baskets. Refer to basket
loading leaflet.

• Make sure that the spray arms can rotate freely.

• The amperage is insufficient to supply simultaneously all the applian‐
ces in use. Check the socket amperage and the capacity of the meter
or turn off one of the appliances in use.

• Internal electrical fault of the appliance. Contact an Authorised Service
Centre.

• Power supply is out of the operating range. The wash cycle is tempora‐
rily interrupted and resumes automatically once the power is restored.

• Complete power outage. The wash cycle is temporarily interrupted and
resumes automatically once the power is restored.

• The appliance downloads and installs the firmware update automatical‐
ly when it is available. The display shows Updating for the duration of
the updating process. Wait for the process to be complete. If you inter‐
rupt the update process by deactivating the appliance, it resumes when
you activate the appliance.
The firmware update does not change the appliance performance dec‐
laration values.

Once you have checked the appliance,
deactivate and activate the appliance. If the
problem occurs again, contact an Authorised
Service Centre.

For alarm codes not described in the table,
contact an Authorised Service Centre.

Before contacting an Authorised Service
Centre, write down the PNC number.
Refer to "Basic settings".

30 ENGLISH

WARNING!

We do not recommend using the
appliance until the problem has been
completely fixed. Unplug the appliance
and do not plug it in again until you are
certain that it operates correctly.

13.1 The dishwashing and drying results are not satisfactory

Problem Possible cause and solution

Poor washing results.

Poor drying results.

There are whitish streaks or bluish lay‐
ers on glasses and dishes.

There are stains and dry water drops
on glasses and dishes.

The interior of the appliance is wet.

Unusual foam during washing.

Traces of rust on cutlery.

There are residues of detergent in the
dispenser at the end of the pro‐
gramme.

• Refer to "Daily use", "Hints and tips" and the basket loading leaf‐
let.

• Use more intensive washing programme.

• Activate the SprayZone option to wash items with heavy or stubborn
soil.

• Activate the ExtraPower option to improve the washing results of a
selected programme.

• Clean spray arm jets and filter. Refer to "Care and Cleaning".

• Tableware was left for too long inside the closed appliance. Activate
the function AirDry to set the automatic opening of the door and to
improve the drying performance.

• There is no rinse aid or the dosage of rinse aid is not sufficient. Fill
the rinse aid dispenser or set the dosage of rinse aid to a higher lev‐
el.

• The quality of the rinse aid can be the cause.

• Always use rinse aid, even with multi-tablets.

• Plastic items may need to be towel dried.

• The programme does not have the drying phase. Refer to "Pro‐
grammes overview".

• The released quantity of rinse aid is too high. Adjust the rinse aid
dosage to a lower level.

• The quantity of detergent is too high.

• The released quantity of rinse aid is not sufficient. Adjust the rinse
aid dosage to a higher level.

• The quality of the rinse aid can be the cause.

• This is not a defect of the appliance. Humidity condensates on the
appliance walls.

• Use the detergent designed specifically for dishwashers.

• Use a detergent from a different manufacturer.

• Do not pre-rinse dishes under running water.

• There is too much salt in the water used for washing. Refer to "The
water softener".

• Silver and stainless steel cutlery were placed together. Do not place
silver and stainless steel items close together.

• The detergent tablet was stuck in the dispenser and was not washed
away by water.

• Water cannot wash away the detergent from the dispenser. Make
sure that the spray arms are not blocked or clogged.

• Make sure that items in the baskets do not impede the lid of the de‐
tergent dispenser from opening.

ENGLISH 31

Problem Possible cause and solution

Odours inside the appliance.

Limescale deposits on the tableware,
on the tub and on the inside of the
door.

Dull, discoloured or chipped table‐
ware.

• Refer to "Internal cleaning".

• Start the Machine Care programme with a descaler or a cleaning
product designed for dishwashers.

• The level of salt is low, check the refill indicator.

• The cap of the salt container is loose.

• Your tap water is hard. Refer to "The water softener".

• Use salt and set regeneration of the water softener even when multi­functional tablets are used. Refer to "The water softener".

• Start the Machine Care programme with a descaler designed for
dishwashers.

• If limescale deposits persist, clean the appliance with the suitable de‐
tergents.

• Try a different detergent.

• Contact the detergent manufacturer.

• Make sure that only dishwasher-safe items are washed in the appli‐
ance.

• Load and unload the basket carefully. Refer to the basket loading
leaflet.

• Place delicate items in the upper basket.

• Activate the GlassCare option to ensure special care for glassware
and delicate items.

Refer to "Before first use", "Daily use",
or "Hints and tips" for other possible
causes.

13.2 Problems with wireless connection

Problem Possible cause and solution

Activating wireless connection is not
successful.

• Wrong wireless network ID or password. Cancel the setup and start
it again to enter the correct credentials. Refer to "Wireless connec‐
tion".

• There is a trouble with the wireless network signal. Check your wire‐
less network and router. Restart the router.

• The wireless network signal is weak. Move router closer to the dish‐
washer.

• The wireless signal is disrupted by a microwave appliance placed
near the dishwasher. Turn off the microwave appliance.

• Contact your wireless service provider if there are further problems
with the wireless network.

32 ENGLISH

Problem Possible cause and solution

The app cannot connect to the dish‐
washer.

The app cannot connect to the dish‐
washer through any network other
than your home wireless network. The

indicator is red or orange.

The app frequently cannot connect to
the dishwasher.

• There is a trouble with the wireless network signal. Check your wire‐
less network and router. Restart the router.

• Check if your mobile device is connected to the network.

• New router was installed or router configuration was changed. Con‐
figure the dishwasher and mobile device again. Refer to "Wireless
connection".

• Contact your wireless service provider if there are further problems
with the wireless network.

• The connection to the cloud is lost. Wait for the connection to be re‐
stored.

• The wireless signal is disrupted by a microwave appliance placed
near the dishwasher. Turn off the microwave appliance. Avoid using
the microwave appliance and the remote start at the same time.

• The wireless network signal is weak. Move router as close to the
dishwasher as possible or consider purchasing a wireless range ex‐
tender.

14. TECHNICAL INFORMATION

Dimensions Width / height / depth (mm) 596 / 818 - 898 / 550

Electrical connection

Water supply pressure Min. / max. MPa (bar) 0.05 (0.5) / 1 (10)

Water supply

Capacity Place settings 15

1)

Refer to the rating plate for other values.

2)

If the hot water comes from alternative source of energy (e.g. solar panels), use the hot water supply to de‐

crease energy consumption.

1)

Voltage (V) 200 - 240

Frequency (Hz) 50 - 60

Cold water or hot water

2)

min. 5 - max. 60 °C

14.1 Link to the EU EPREL database

The QR code on the energy label supplied
with the appliance provides a web link to the
registration of this appliance in the EU
EPREL database. Keep the energy label for
reference together with the user manual and
all other documents provided with this
appliance.

It is possible to find information related to the
performance of the product in the EU EPREL

database using the link https://
eprel.ec.europa.eu and the model name and
product number that you can find on the
rating plate of the appliance. Refer to the
chapter "Product description".

For more detailed information about the
energy label, visit www.theenergylabel.eu.

ENGLISH 33

15. ENVIRONMENTAL CONCERNS

Recycle materials with the symbol . Put the
packaging in relevant containers to recycle it.
Help protect the environment and human
health by recycling waste of electrical and
electronic appliances. Do not dispose of

appliances marked with the symbol with
the household waste. Return the product to
your local recycling facility or contact your
municipal office.

34 ENGLISH

*

My Electrolux Kitchen app

The software in this product contains components that are based on free and open source software. Electrolux
gratefully acknowledges the contributions of the open software and robotics communities to the development project.

To access the source code of these free and open source software components whose license conditions require
publishing, and to see their full copyright information and applicable license terms, please visit:
http://electrolux.opensoftwarerepository.com (folder NIUS)

117834990-A-262023