y
prop
y
y
Thank you very much for choosing an EIZO product.
Please read this User’s Manual carefully to familiarize you with safe and effective usage procedures.
Please retain this manual for future reference.
PRECAUTIONS
To ensure personal safety and proper maintenance, please read this section.
CAUTION
Do not carry the monitor with the hood attached.
While carrying the monitor, the hood may fall or slip off, which may result in injury or equipment damage.
Do not place any objects on the hood.
If the hood falls or slips off or the monitor falls over, it may result in injury or equipment damage.
Attach only to specified EIZO LCD monitors.
Attach only to specified EIZO LCD monitors. Attaching to other monitors may cause the hood to drop, which ma
result in injury or equipment damage. For the specified monitors, please visit our website at http://www.eizo.com.
Close the open/close cover until it contacts the stopper.
If the cover is not closed properly, the ventilation slots on the monitor will be covered and
prevented. This may cause overheating inside the monitor and ma
damage.
When attaching the hood to the 22.0-inch monitor with EZ-UP stand, do not attach the hood and i·Sound
(optional speaker) at the same time.
It ma
cause falling of the monitor, and may result in injury or equipment damage because the total weight exceeds
the supportable weight of the stand.
result in fire, electric shock, or equipment
er airflow will be
Package Contents
Please contact your local dealer for assistance if any of the listed items are missing or damaged.
Left Hood
(1) Left cover
Right Hood
(2) Top cover
______________________________________________
(6) Metal fitting
(7) Open/close
cover
Rubber cushions
(for 22.0-inch monitor)
(3) Top cover
(4) Right cover
(5) Hooks
For metal
fitting
User’s Manual（this manual）
For hood
How to install
1. For 22.0-inch monitors, attach the rubber cushions on the both hoods (left and right covers)
and the metal fitting.
NOTE
For 24.1-inch monitors, start at step 2.
Left and right hoods
(1) Remove the tape from a rubber cushion for hood, and then attach the cushion on the left hood (left cover)
(2) Attach another rubber cushion for hood on the right hood (right cover) in the same way.
along the line with no space between the cushion and the hood.
__________________________________________________
Leave no space
between them
Attach the sticky side of
the cushion on this side
Line
Metal fitting
Remove the tape from the rubber cushion for metal fitting, and then attach the cushion on the metal fitting
with no space between the cushion and the fitting.
Attach them as the short sides
face to the top and bottom
Leave no space between them
Attach the sticky side of the cushion on this side
2. Assemble the left and right hoods.
I
”
NOTE
Assemble the hoods in the direction of the arrows marked on the insertions on the top covers of the right and left
(1) Hold the left hood's left and top covers with the sides with the anti-reflective sheet facing inward.
(2) Connect the top and left covers by aligning the arrow (1 ) on the top cover's insertion with the two lines
(3) Slide the top cover in the direction shown by the arrow (2 ).
(4) Assemble the right hood in the same way.
hoods.
on the left cover's insertion slot.
Assembly of the left hood is complete.
(1) (2)
Anti-reflective
sheet
nsertion
slot
Insertion
(3)
3. Attach the left and right hoods to the monitor.
NOTE
Be sure to install the second hood only after the other hood is firmly attached with hook.
When attaching the hood to the 22.0-inch monitor with EZ-UP stand, note the following points:
(1) Attach the top side of the left hood to the monitor first and then securely fit the left side of the hood in order
- The height of the hood is about 16 mm longer than the one of 22-inch monitor, so that with tilting at the lowest
lifting position the hood may hit the desk on which the monitor is installed.
- When attaching the hood and i·Sound (optional speaker) at the same time, the total weight exceeds the
supportable weight of the stand. Before attaching the hood, remove i·Sound from the monitor.
to fix the hood to the monitor.
(2) Insert the hook into the hole* on the hood (a) and slide it down along the projection on the back side of the monitor (b).
monitors
Locations for hook
For 22.0”monitors
Insert into the hole
upper protection
* The location for hook depends on the size of the monitor.
For 24.1
Insert into the hole
under projection
(3) Attach the right hood in the same way.
Loading...