Einhell TE-TS 36/210 Li - EX - NA Manual
EN Operating instructions
Cordless Worksite Table Saw
FR Mode d’emploi
Scie de chantier sans fi l
SP Manual de instrucciones
Sierra de mesa inalámbrica para el
lugar de trabajo
TE-TS 36/210 Li
7
Art.-Nr.: 4340451 I.-Nr.: 21011
Anl_TE_TS_36_210_Li_USA_SPK7.indb 1Anl_TE_TS_36_210_Li_USA_SPK7.indb 1 07.10.2022 09:39:1407.10.2022 09:39:14
1
121 14 38 2 10 7
42
3981141
1229
2
2
Anl_TE_TS_36_210_Li_USA_SPK7.indb 2Anl_TE_TS_36_210_Li_USA_SPK7.indb 2 07.10.2022 09:39:1507.10.2022 09:39:15
3
53031 14 16
- 2 -
3 4
26
7
27
28
25
23
5 6
37 37 1617
3
30/31
14
7 8
61
30
13
- 3 -
Anl_TE_TS_36_210_Li_USA_SPK7.indb 3Anl_TE_TS_36_210_Li_USA_SPK7.indb 3 07.10.2022 09:39:1607.10.2022 09:39:16
6 1
9 10
4
15 19
20
11 12
54
30
5
20 19
19
13 14
30
13
Anl_TE_TS_36_210_Li_USA_SPK7.indb 4Anl_TE_TS_36_210_Li_USA_SPK7.indb 4 07.10.2022 09:39:2307.10.2022 09:39:23
4
65
18
- 4 -
2
18
5
4
15 16
15
4
3130
17 18
16
2
38
19 20
2
2
4616
45
Anl_TE_TS_36_210_Li_USA_SPK7.indb 5Anl_TE_TS_36_210_Li_USA_SPK7.indb 5 07.10.2022 09:39:2707.10.2022 09:39:27
41 32 8 9 3311
- 5 -
21 22
9
8 8 9
23 24
25 26
21 21
23 7729
22 2224 24
12
23 1017
29
12
22 24
- 6 -
Anl_TE_TS_36_210_Li_USA_SPK7.indb 6Anl_TE_TS_36_210_Li_USA_SPK7.indb 6 07.10.2022 09:39:3407.10.2022 09:39:34
27 28
101
34
21
42 10 4344
35
36
29 30
14
23
45°
4
26
31
42 10 4344
Anl_TE_TS_36_210_Li_USA_SPK7.indb 7Anl_TE_TS_36_210_Li_USA_SPK7.indb 7 07.10.2022 09:39:4007.10.2022 09:39:40
32
40
40
- 7 -
33 34
39
39
35 36
37 38
3
- 8 -
Anl_TE_TS_36_210_Li_USA_SPK7.indb 8Anl_TE_TS_36_210_Li_USA_SPK7.indb 8 07.10.2022 09:39:4807.10.2022 09:39:48
39 40
41
42
48
47
1637
- 9 -
Anl_TE_TS_36_210_Li_USA_SPK7.indb 9Anl_TE_TS_36_210_Li_USA_SPK7.indb 9 07.10.2022 09:39:5407.10.2022 09:39:54
EN
Danger! - Read the operating instructions to reduce the risk of injury.
Caution! Wear ear-muff s. The impact of noise can cause damage to hearing.
Caution! Wear a breathing mask. Dust which is injurious to health can be generated when working on
wood and other materials. Never use the tool to work on any materials containing asbestos!
Caution! Wear safety goggles. Sparks generated during work or splinters, chips and dust emitted by
the equipment can cause loss of sight.
104°F
(+40°C)
50°F
(+10°C)
Store the batteries only in dry rooms with an ambient temperature of 50°F to 104°F (+10°C to +40°C).
Place only fully charged batteries in storage (charged at least 40%).
Caution! Risk of injury! Do not reach into the running saw blade.
Using the supplied ring wrench, turn the disk counterclockwise to release the table insert. Turn the disk
clockwise to secure the table insert and prevent it falling out.
- 10 -
Anl_TE_TS_36_210_Li_USA_SPK7.indb 10Anl_TE_TS_36_210_Li_USA_SPK7.indb 10 07.10.2022 09:39:5707.10.2022 09:39:57
EN
DANGER!
When using the equipment, a number of safety
precautions must be observed to avoid injuries
and damage. Please read the complete operating
instructions and safety information with due care.
Keep these operating instructions in a safe place
so that the information is available at all times. If
you give the equipment to any other person, hand
over these operating instructions and the safety
information as well. We cannot accept any liability for damage or accidents which arise due to
failure to follow these instructions and the safety
information.
1. Safety information
DANGER!
Read all the safety information and instructions. Failure to adhere to the safety information
and instructions set out below may result in electric shock, fi re and/or serious injury. Keep all the
safety information and instructions in a safe
place for future use.
General safety information for power tools
The term “power tool“ used in the safety regulations refers to power tools operated from the mains
power supply (with a power cable) and to battery
operated power tools (without a power cable).
1) Work area safety
a) Keep work area clean and well lit. Clutte-
red and dark areas invite accidents.
b) Do not operate power tools in explosive
atmospheres, such as in the presence of
fl ammable liquids, gases or dust. Power
tools create sparks which may ignite the dust
or fumes.
c) Keep children and bystanders away while
operating a power tool. Distractions can
cause you to lose control.
2) Electrical safety
a) Power tool plugs must match the outlet.
Never modify the plug in any way. Do
not use any adapter plugs with earthed
(grounded) power tools. Unmodifi ed plugs
and matching outlets will reduce risk of electric shock.
b) Avoid body contact with earthed or
grounded surfaces such as pipes, radiators, ranges and refrigerators. There is an
increased risk of electric shock if your body is
earthed or grounded.
c) Do not expose power tools to rain or wet
conditions. Water entering a power tool will
increase the risk of electric shock.
d) Do not abuse the cord. Never use the
cord for carrying, pulling or unplugging
the power tool. Keep cord away from
heat, oil, sharp edges or moving parts.
Damaged or entangled cords increase the
risk of electric shock.
e) When operating a power tool outdoors,
use an extension cord suitable for outdoor use. Use of a cord suitable for outdoor
use reduces the risk of electric shock.
f) If operating a power tool in a damp
location is unavoidable, use a ground
fault circuit interruptor (GFCI) protected
supply. Use of an GFCI reduces the risk of
electric shock.
3) Personal safety
a) Stay alert, watch what you are doing and
use common sense when operating a
power tool. Do not use a power tool while
you are tired or under the infl uence of
drugs, alcohol or medication. A moment of
inattention while operating power tools may
result in serious personal injury.
b) Use personal protective equipment.
Always wear eye protection. Protective
equipment such as dust mask, non-skid safety shoes, hard hat, or hearing protection used
for appropriate conditions will reduce personal injuries.
c) Prevent unintentional starting. Ensure the
switch is in the Off -position before con-
necting to power source and/or BATTERY
pack, picking up or carrying the tool.
Carrying power tools with your fi nger on the
switch or energizing power tools that have the
switch on invites accidents.
d) Remove any adjusting key or wrench be-
fore turning the power tool on. A wrench
or a key left attached to a rotating part of the
power tool may result in personal injury.
e) Do not overreach. Keep proper footing
and balance at all times. This enables
better control of the power tool in unexpected
situations.
f) Dress properly. Do not wear loose
clothing or jewellery. Keep your hair,
clothing and gloves away from moving
parts. Loose clothes, jewelery or long hair
can be caught in moving parts.
g) If devices are provided for the connection
- 11 -
Anl_TE_TS_36_210_Li_USA_SPK7.indb 11Anl_TE_TS_36_210_Li_USA_SPK7.indb 11 07.10.2022 09:39:5807.10.2022 09:39:58
EN
of dust extraction and collection facilities,
ensure these are connected and properly
used. Use of these devices can reduce dust
related hazards.
h) Do not let familiarity gained from frequent
use of tools allow you to become complacent and ignore tool safety principles. A
careless action can cause severe injury within
a fraction of a second.
4) Power tool use and care
a) Do not force the power tool. Use the cor-
rect power tool for your application. The
correct power tool will do the job better and
safer at the rate for which it was designed.
b) Do not use the power tool if the switch
does not turn it on and off . Any power tool
that cannot be controlled with the switch is
dangerous and must be repaired.
c) Disconnect the plug from the power
source and/or remove the battery pack,
if detachable, from the power tool before
making any adjustments, changing accessories, or storing power tools. Such
preventive safety measures reduce the risk of
starting the power tool accidentally.
d) Store idle power tools out of the reach of
children and do not allow persons unfamiliar with the power tool or these instructions to operate the power tool. Power
tools are dangerous in the hands of untrained
users.
e) Maintain power tools and accessories.
Check for misalignment or binding of
moving parts, breakage of parts and any
other condition that may aff ect the power
tool’s operation. If damaged, have the
power tool repaired before use. Many acci-
dents are caused by poorly maintained power
tools.
f) Keep cutting tools sharp and clean. Pro-
perly maintained cutting tools with sharp
cutting edges are less likely to bind and are
easier to control.
g) Use the power tool, accessories and tool
bits etc., in accordance with these instructions and in the manner intended for
the particular type of power tool, taking
into account the working conditions and
the work to be performed. Use of the power
tool for operations diff erent from intended
could result in a hazardous situation.
h) Keep handles and grasping surfaces dry,
clean and free from oil and grease. Slip-
pery handles and grasping surfaces do not
allow for safe handling and control of the tool
in unexpected situations.
5) Battery tool use and care
a) Recharge only with the charger specifi ed
by the manufacturer. A charger that is sui-
table for one type of battery pack may create
a risk of fi re when used with another battery
pack.
b) Use power tools only with specifi cally
designated battery packs. Use of any other
battery packs may create a risk of injury and
fi re.
c) When battery pack is not in use, keep it
away from other metal objects, like paper
clips, coins, keys, nails, screws or other
small metal objects that can make a
connection from one terminal to another.
Shorting the battery terminals together may
cause burns or a fi re.
d) Under abusive conditions, liquid may be
ejected from the battery; avoid contact.
If contact accidentally occurs, fl ush with
water. If liquid contacts eyes, additionally
seek medical help. Liquid ejected from the
battery may cause irritation or burns.
e) Do not use a BATTERY pack or tool that
is damaged or modifi ed. Damaged or
modifi ed batteries may exhibit unpredictable
behavior resulting in fi re, EXPLOSION or risk
of injury.
f) Do not expose a BATTERY pack or tool to
fi re or excessive temperature. Exposure to
fi re or temperature above 266°F (130°C) may
cause explosion.
g) Follow all charging instructions and do
not charge the BATTERY pack or tool outside the temperature range specifi ed in
the instructions. Charging improperly or at
temperatures outside the specifi ed range may
damage the BATTERY and increase the risk
of fi re.
6) Service
a) Have your power tool serviced by a qua-
lifi ed repair person using only identical
replacement parts. This will ensure that the
safety of the power tool is maintained.
b) Never service damaged BATTERY packs.
Service of BATTERY packs should only be
performed by the manufacturer or authorized
service providers.
Additional safety instructions
We pay a great deal of attention to the design of
- 12 -
Anl_TE_TS_36_210_Li_USA_SPK7.indb 12Anl_TE_TS_36_210_Li_USA_SPK7.indb 12 07.10.2022 09:39:5807.10.2022 09:39:58
EN
every battery pack to ensure that we supply you
with batteries which feature maximum power density, durability and safety. The battery cells have
a wide range of safety devices. Each individual
cell is initially formatted and its electrical characteristic curves are recorded. These data are then
used exclusively to be able to assemble the best
possible battery packs.
Despite all the safety precautions, caution
must always be exercised when handling batteries. The following points must be obeyed
at all times to ensure safe use.
Safe use can only be guaranteed if undamaged cells are used. Incorrect handling can
cause cell damage.
9. Avoid damage and shocks. Replace batte-
ries which have been dropped from a height
of more than one meter or which have been
exposed to violent shocks without delay, even
if the housing of the battery pack appears to
be undamaged. The battery cells inside the
battery may have suff ered serious damage.
In this respect, please also read the waste
disposal information.
10. If the battery pack suff ers overloading and
overheating, the integrated protective cutoff will switch off the equipment for safety
reasons. Caution! Do not press the ON/OFF
switch any more if the protective cut-off has
actuated. This may damage the battery.
11. Use only original battery packs. The use of
Caution! Analyses confi rm that incorrect use and
poor care are the main causes of the damage
caused by high performance batteries.
other batteries may result in injuries, explosion and a fi re risk.
12. Protect your rechargeable battery against
moisture, rain and high humidity. Moisture,
Information about the battery
1. The battery pack supplied with your cordless
tool is not charged. The battery pack has to
be charged before you use the tool for the fi rst
time.
2. For optimum battery performance avoid low
discharge cycles. Charge the battery pack
frequently.
rain and high humidity can cause dangerous
cell damage. Never charge or work with batteries which have been exposed to moisture,
rain or high humidity – replace them immediately.
13. If your equipment is fi tted with a detachable
battery, remove the battery for safety reasons
after you have fi nished your work.
3. Store the battery pack in a cool place, ideally
at 59°F (15°C) and charged to at least 40%.
4. Lithium-Ion batteries are subject to a natural
ageing process. The battery pack must be
replaced at the latest when its capacity falls to
just 80% of its capacity when new. Weakened
cells in an aged battery pack are no longer
capable of meeting the high power requirements and therefore pose a safety risk.
5. Do not throw battery packs into an open fi re.
There is a risk of explosion!
6. Do not ignite the battery pack or expose it to
fi re.
7. Do not exhaustively discharge batteries.
Exhaustive discharge will damage the battery cells. The most common cause of deep
discharge is lengthy storage or non-use of
partly discharged batteries. Stop working as
soon as the performance of the battery falls
noticeably or the electronic protection system
triggers. Place the battery pack in storage
only after it has been fully charged.
8. Protect batteries and the tool from over-
loads. Overloads will quickly result in overheating and cell damage inside the battery
housing without this overheating actually
being apparent externally.
Information on chargers and the charging
process
1. Please check the data marked on the rating
plate of the battery charger. Be sure to connect the battery charger to a power supply
with the voltage marked on the rating plate.
Never connect it to a diff erent mains voltage.
2. Protect the battery charger and its cable from
damage and sharp edges. Have damaged
cables repaired without delay by a qualifi ed
electrician.
3. Keep the battery charger, batteries and the
cordless tool out of children‘s reach.
4. Do not use damaged battery chargers.
5. Do not use the supplied battery charger to
charge other cordless tools.
6. In heavy use the battery pack will become
warm. Allow the battery pack to cool to room
temperature before commencing with the
charging.
7. Do not over-charge batteries. Do not exceed the maximum charging times. These
charging times apply only to discharged
batteries. Frequent insertion of a charged or
partly charged battery pack will result in overcharging and cell damage. Do not leave bat-
- 13 -
Anl_TE_TS_36_210_Li_USA_SPK7.indb 13Anl_TE_TS_36_210_Li_USA_SPK7.indb 13 07.10.2022 09:39:5807.10.2022 09:39:58
EN
teries in the charger for more than 48 hours.
8. Never use or charge batteries if you sus-
pect that the last time they were charged
was more than 12 months previously. The-
re is a high probability that the battery pack
has already suff ered dangerous damage
(exhaustive discharge).
9. Charging batteries at a temperature below
50°F (10°C) will cause chemical damage to
the cell and may cause a fi re.
10. Do not use batteries which have heated during the charging process, as the battery cells
may have suff ered dangerous damage.
11. Do not use batteries which have suff ered
curvature or deformation during the charging
process or which show other non-typical symptoms (gassing, hissing, cracking,…)
12. Never fully discharge the battery pack (recommended depth of discharge max. 80%)
A complete discharge of the battery pack will
lead to premature ageing of the battery cells.
13. Never charge the batteries unsupervised.
Protection from environmental infl uences
1. Wear suitable work clothes. Wear safety goggles.
2. Protect your cordless tool and the battery
charger from moisture and rain. Moisture
and rain can cause dangerous cell damage.
3. Do not use the cordless tool or the battery
charger near vapors and infl ammable liquids.
4. Use the battery charger and cordless tools
only in dry conditions and an ambient temperature of 50°F to 104°F (10°C to 40°C).
5. Do not keep the battery charger in places
where the temperature is liable to reach over
104°F (40°C). In particular, do not leave the
battery charger in a car that is parked in the
sunshine.
6. Protect batteries from overheating. Over-
loads, over-charging and exposure to direct
sunlight will result in overheating and cell
damage. Never charge or work with batteries
which have been overheated – replace them
immediately if possible.
7. Storage of batteries, battery chargers
and cordless tools. Store the charger and
your cordless tool only in dry places with an
ambient temperature of 50°F to 104°F (10°C
to 40°C). Store the Lithium-Ion rechargeable
battery in a cool and dry place at 50°F to 68°F
(10°C to 20°C). Protect them from humidity
and direct sunlight! Place only fully charged
batteries in storage (charged at least 40%).
8. Prevent the Lithium-Ion battery pack from
freezing. Battery packs which were stored
below 32°F (0°C) for more than 60 minutes
must be disposed of.
9. When handling batteries beware of electrostatic charge: Electrostatic discharges cause
damage of the electronic protection system
and the battery cells. Avoid electrostatic charging and never touch the battery poles.
Battery Caution + Disposal
Disposal
Should your appliance need replacement after extended use, do not dispose of it with the
household refuse, but in an environmentally safe
way.
Waste produced by electrical machine
items should not be handled like normal
household rubbish. Please recycle where
recycle facilities exist. Check with your local
authority or retailer for recycling advice.
Always dispose of your battery pack according to
federal, state, provincial and local regulations. Contact a recycling agency in your area for recycling
locations.
CAUTION! Even discharged battery packs
contain some energy. Before disposing, use electrical tape to cover the terminals to prevent the
battery pack from shorting, which could cause a
fi re or explosion.
WARNING! To reduce the risk of injury or
explosion, never burn or incinerate a battery
pack even if it is damaged, dead, or completely
discharged. When burned, toxic fumes and materials are emitted into the surrounding atmosphere.
1. Batteries vary according to device. Consult
your manual for specifi c information.
2. Install only new batteries of the same type in
your product (where applicable).
3. Failure to insert batteries in the correct polari-
ty, as indicated in the battery compartment or
manual, may shorten the life of the batteries
or cause batteries to leak.
4. Do not mix old and new batteries.
5. Do not mix Alkaline, Standard (Carbon-Zinc),
or Rechargeable (Nickel Cadmium, Nickel
Metal Hydride, or Lithium-Ion) batteries.
6. Do not dispose of batteries in fi re.
7. Batteries should be recycled or disposed of
as per state, provincial and local guidelines.
When shipping or disposing of batteries and
cordless tools, always ensure that they are
packed individually in plastic bags to prevent
- 14 -
Anl_TE_TS_36_210_Li_USA_SPK7.indb 14Anl_TE_TS_36_210_Li_USA_SPK7.indb 14 07.10.2022 09:39:5807.10.2022 09:39:58
EN
short circuits and fi res.
Special safety instructions for cordless portable worksite table saws
1) Guarding related warnings
a) Keep guards in place. Guards must be in
working order and be properly mounted.
A guard that is loose, damaged, or is not
functioning correctly must be repaired or replaced.
b) Always use saw blade guard and the
riving knife for every through–cutting
operation. For through-cutting operations
where the saw blade cuts completely through
the thickness of the workpiece, the guard and
other safety devices help reduce the risk of
injury.
c) Do not use this saw to make operations
such as rabbeting, dadoing or resawing
cuts. For design reasons, the saw is not sui-
table for such work. The guard and riving knife
must never be removed, because it reduces
the risk of injury.
d) Make sure the saw blade is not contac-
ting the guard, riving knife or the workpiece before the switch is turned on. Inad-
vertent contact of these items with the saw
blade could cause a hazardous condition.
e) Adjust the riving knife as described in
this instruction manual. Incorrect spacing,
positioning and alignment can make the riving
knife ineff ective in reducing the likelihood of
kickback.
f) For the riving knife to work, it must be en-
gaged in the workpiece. The riving knife is
ineff ective when cutting workpieces that are
too short to be engaged with the riving knife.
Under these conditions a kickback cannot be
prevented by the riving knife.
g) Use the appropriate saw blade for the ri-
ving knife. For the riving knife to function pro-
perly, the saw blade diameter must match the
appropriate riving knife and the body of the
saw blade must be thinner than the thickness
of the riving knife and the cutting width of the
saw blade must be wider than the thickness
of the riving knife.
2) Cutting procedures warnings
a) DANGER: Never place your fi ngers or
hands in the vicinity or in line with the
saw blade. A moment of inattention or a slip
could direct your hand towards the saw blade
and result in serious personal injury.
b) Feed the workpiece into the saw blade
only against the direction of rotation. Fee-
ding the workpiece in the same direction that
the saw blade is rotating above the table may
result in the workpiece, and your hand, being
pulled into the saw blade.
c) Never use the miter gauge to feed the
workpiece when ripping and do not use
the rip fence as a length stop when cross
cutting with the miter gauge. Guiding the
workpiece with the rip fence and the miter
gauge at the same time increases the likelihood of saw blade binding and kickback.
d) When ripping, always apply the workpie-
ce feeding force between the fence and
the saw blade. Use a push stick when the
distance between the fence and the saw
blade is less than 5.9" (150 mm), and use
a push block when this distance is less
than 1.9" (50 mm). “Work helping” devices
will keep your hand at a safe distance from
the saw blade.
e) Use only the push stick provided by
the manufacturer or constructed in accordance with the instructions. This push
stick provides suffi cient distance of the hand
from the saw blade.
f) Never use a damaged or cut push stick. A
damaged push stick may break causing your
hand to slip into the saw blade.
g) Do not perform any operation “freehand”.
Always use either the rip fence or the miter gauge to position and guide the workpiece. “Freehand” means using your hands
to support or guide the workpiece, instead of
a rip fence or miter gauge. Freehand sawing
leads to misalignment, binding and kickback.
h) Never reach around or over a rotating
saw blade. Reaching for a workpiece may
lead to accidental contact with the moving
saw blade.
i) Provide auxiliary workpiece support to
the rear and/or sides of the saw table
for long and/or wide workpieces to keep
them level. A long and/or wide workpiece
has a tendency to pivot on the table’s edge,
causing loss of control, saw blade binding
and kickback.
j) Feed workpiece at an even pace. Do not
bend or twist the workpiece. If jamming
occurs, turn the tool off immediately, un-
plug the tool then clear the jam. Jamming
the saw blade by the workpiece can cause
kickback or stall the motor.
k) Do not remove pieces of cut-off material
- 15 -
Anl_TE_TS_36_210_Li_USA_SPK7.indb 15Anl_TE_TS_36_210_Li_USA_SPK7.indb 15 07.10.2022 09:39:5807.10.2022 09:39:58
EN
while the saw is running. The material
may become trapped between the fence or
inside the saw blade guard and the saw blade
pulling your fi ngers into the saw blade. Turn
the saw off and wait until the saw blade stops
before removing material.
l) Use an auxiliary fence in contact with the
table top when ripping workpieces less
than 0.079" (2 mm) thick. A thin workpiece
may wedge under the rip fence and create a
kickback.
m) Avoid overheating of the saw blade and/
or burn marks on the workpiece. Push the
workpiece smoothly into the saw blade and
do not stop during the cut.
3) Kickback causes and related warnings
Kickback is a sudden reaction of the workpiece
due to a pinched, jammed saw blade or misaligned line of cut in the workpiece with respect to the
saw blade or when a part of the workpiece binds
between the saw blade and the rip fence or other
fi xed object.
Most frequently during kickback, the workpiece is
lifted from the table by the rear portion of the saw
blade and is propelled towards the operator.
Kickback is the result of saw misuse and/or incorrect operating procedures or conditions and can
be avoided by taking proper precautions as given
below.
a) Never stand directly in line with the saw
blade. Always position your body on the
same side of the saw blade as the fence.
Kickback may propel the workpiece at high
velocity towards anyone standing in front and
in line with the saw blade.
b) Never reach over or in back of the saw
blade to pull or to support the workpiece.
Accidental contact with the saw blade may
occur or kickback may drag your fi ngers into
the saw blade.
c) Never hold and press the workpiece that
is being cut off against the rotating saw
blade. Pressing the workpiece being cut off
against the saw blade will create a binding
condition and kickback.
d) Align the fence to be parallel with the
saw blade. A misaligned fence will pinch the
workpiece against the saw blade and create
kickback.
e) Do not use this saw to make operations
such as rabbeting, dadoing or resawing
cuts. For design reasons, the saw is not sui-
table for such work. The guard and riving knife
must never be removed, because it reduces
the risk of injury.
f) Use extra caution when making a cut into
blind areas of assembled workpieces. The
protruding saw blade may cut objects that
can cause kickback.
g) Support large panels to minimise the risk
of saw blade pinching and kickback. Lar-
ge panels tend to sag under their own weight.
Support(s) must be placed under all portions
of the panel overhanging the table top.
h) Do not work on any workpiece that is
twisted, knotted, warped or does not
have a straight edge to guide it with a
miter gauge or along the fence. A warped,
knotted, or twisted workpiece is unstable and
causes misalignment of the kerf with the saw
blade, binding and kickback.
i) Never cut more than one workpiece, sta-
cked vertically or horizontally. The saw
blade could pick up one or more pieces and
cause kickback.
j) Do not start the saw if the saw blade is
in the workpiece. If the saw blade binds, it
may lift up the workpiece and cause kickback
when the saw is restarted.
k) Keep saw blades clean, sharp, and with
suffi cient set. Never use warped saw bla-
des or saw blades with cracked or broken
teeth. Sharp and properly set saw blades
minimise binding, stalling and kickback.
4) Table saw operating procedure warnings
a) Turn off the table saw and disconnect
battery when removing the table insert,
changing the saw blade or making adjustments to the riving knife or saw blade
guard, and when the machine is left unattended. Precautionary measures will avoid
accidents.
b) Never leave the table saw running un-
attended. Turn it off and don’t leave the
tool until it comes to a complete stop. An
unattended running saw is an uncontrolled
hazard.
c) Locate the table saw in a well-lit and level
area where you can maintain good footing and balance. It should be installed
in an area that provides enough room to
easily handle the size of your workpiece.
Cramped, dark areas, and uneven slippery
fl oors invite accidents.
d) Frequently clean and remove sawdust
from under the saw table and/or the dust
collection device. Accumulated sawdust is
combustible and may self-ignite.
- 16 -
Anl_TE_TS_36_210_Li_USA_SPK7.indb 16Anl_TE_TS_36_210_Li_USA_SPK7.indb 16 07.10.2022 09:39:5807.10.2022 09:39:58
EN
e) The table saw must be secured. A table
saw that is not properly secured may move or
tip over.
f) Remove tools, wood scraps, etc. from the
table before the table saw is turned on.
Distraction or a potential jam can be dangerous.
g) Always use saw blades with correct size
and shape (diamond versus round) of
arbor holes. Saw blades that do not match
the mounting hardware of the saw will run off -
centre, causing loss of control.
h) Never use damaged or incorrect saw
blade mounting means such as fl anges,
saw blade washers, bolts or nuts. These
mounting means were specially designed
for your saw, for safe operation and optimum
performance.
i) Never stand on the table saw, do not use
it as a stepping stool. Serious injury could
occur if the tool is tipped or if the cutting tool
is accidentally contacted.
j) Make sure that the saw blade is installed
to rotate in the proper direction. Do not
use grinding wheels, wire brushes, or
abrasive wheels on a table saw. Improper
saw blade installation or use of accessories
not recommended may cause serious injury.
5) Additional safety information
1. Only use a saw blade which has the external
diameter and hole diameter specifi ed in the
original operating instructions (“Technical
data” section).
2. Use only blades with rotating speeds which
are equal to or higher than the rotating speed
marked on the power tool.
3. Use only a saw blade with a diameter which
is the same as specifi ed on the saw.
4. Use the correct saw blade for the material you
are working on.
5. Use only saw blades which are recommended by the manufacturer which, if they are
intended for cutting wood or similar materials,
comply with EN 847-1.
6. Only fi t blades which are well sharpened and
have no cracks or deformations.
7. Faulty saw blades must be replaced immediately.
8. It must be possible for the blade to run freely.
9. Check the saw blade guard for damage and
wear each time before using the saw.
10. The saw blade guard must lower again automatically under its own weight after each cut.
The saw blade guard must lift when the work-
piece is pushed in the direction of the saw
blade.
11. Damaged or faulty safety devices have to be
replaced immediately.
12. It is imperative to make sure that all devices
which cover the saw blade are in good working order.
13. Never dismantle the machine‘s safety devices
or render them inoperative.
14. Refi t all guards and safety devices immedia-
tely after you have completed any repairs or
maintenance work.
15. Keep the push stick or handle for a push
block at the machine at all times, even when
you are not using them. Slot the push stick or
the push block into its holder when not in use.
16. The sawing of angles/wedges is only permitted if an appropriate auxiliary stop (cross
stop) is used.
17. If the table insert is worn, replace it. – Pull out
the battery.
18. If necessary, wear suitable personal protection equipment. This could consist of:
a. Ear plugs to prevent the risk of damaging
your hearing.
b. A breathing mask to avoid the risk of inhaling hazardous dust.
c. Always wear gloves when handling saw
blades and rough materials. Whenever
practicable, saw blades must be carried in a
container.
19. Use only the transport devices to move the
equipment. Never use the guards for handling
or moving the equipment.
20. While you are moving the machine it is best
to cover the top part of the blade, e.g. with the
guard.
21. Give these safety instructions to all persons
who work on the machine.
22. Do not use this saw to cut fi re wood.
23. Do not use this saw to cross-cut round wood.
24. The machine is equipped with a safety switch
to prevent it from being switched on again
accidentally after a power failure.
25. Never load the machine so much that it cuts
out.
26. Always press the workpiece fi rmly against the
saw table.
27. Make sure that off -cuts do not catch on the
saw blade crown. Risk of catapulting!
28. Be sure to observe the safety information
and operating and maintenance instructions
issued by the manufacturer, as well as the
dimensions listed in the Technical Data.
29. It is imperative to observe the accident pre-
- 17 -
Anl_TE_TS_36_210_Li_USA_SPK7.indb 17Anl_TE_TS_36_210_Li_USA_SPK7.indb 17 07.10.2022 09:39:5807.10.2022 09:39:58
EN
vention regulations in force in your area as
well as all other generally recognized rules of
safety.
30. Note the information published by your professional associations.
31. Operators must be at least 18 years of age.
32. Never remove loose splinters, chips or jammed pieces of wood when the saw blade is
running.
33. To rectify faults or remove jammed pieces of
wood, always switch off the machine fi rst. –
Pull out the battery.
34. Persons working on the machine should not
be distracted.
35. Keep your workplace clean of wood scrap
and any unnecessary objects.
36. Before you use the machine for the fi rst time,
check that the voltage marked on the rating
plate is the same as your supply voltage.
37. Operate the saw only with a suitable vacuum
extraction system or a standard industrial vacuum cleaner.
38. Keep unused electric tools out of the reach of
children. Do not allow people who are not familiar with the tool or who have not read these
instructions to use the tool. Electric tools are
dangerous if they are used by inexperienced
people.
39. Keep your cutting tools sharp and clean.
Carefully maintained cutting tools with sharp
cutting edges will jam less and are easier to
control.
40. Have your tool repaired only by trained personnel using only genuine spare parts. This
will ensure that your tool remains safe to use.
41. All covers and safety devices have to be properly fi tted before the equipment is switched
on.
42. When working with wood that has been processed before, watch out for foreign bodies
such as nails or screws etc.
43. Before you actuate the On/Off switch, make
sure that the saw blade is correctly fi tted
and that the equipment‘s moving parts run
smoothly.
44. Keep handles dry, clean and free from oil and
grease.
SAVE THESE INSTRUCTIONS
2. Layout and items supplied
2.1 Layout
1. Saw table
2. Saw blade guard
3. Push stick
4. Blade
5. Riving knife
6. Table insert
7. Complete rip fence
8. Hand wheel
9. Locking lever for saw blade angle
10. Extension table
11. On/Off switch
12. Eccentric lever for rip fence
13. Rotary disk in table insert
14. Miter gauge
15. Screw for saw blade
16. Extractor adapter
17. Recessed head screw
18. Hole in riving knife
19. Fastening screw
20. Fastening plate
21. Slot in saw table
22. Main scale
23. Stop rail
24. Additional scale
25. Slot in stop rail
26. Knurled screw for rip fence
27. Washer for rip fence
28. Lock bolt for rip fence
29. Guide rail for rip fence
30. 10/13 mm ring wrench
31. 10/21 mm ring wrench
32. Adjustment screw (0°)
33. Adjustment screw (45°)
34. Stop rail for cross stop
35. Knurled screw for miter gauge
36. Locking screw for miter gauge
37. Dust collector
38. Cap on saw blade guard
39. Battery (not supplied)
40. Mount for battery
41. Emergency stop switch cover
42. Clamping lever for table width extension
43. Threaded sleeve
44. Nut
45. Suction hose (not included)
46. Adapter (not included)
47. Battery capacity indicator
48. Battery capacity indicator button
- 18 -
Anl_TE_TS_36_210_Li_USA_SPK7.indb 18Anl_TE_TS_36_210_Li_USA_SPK7.indb 18 07.10.2022 09:39:5807.10.2022 09:39:58
EN
2.2 Items supplied
Please check that the article is complete as
specifi ed in the scope of delivery. If parts are
missing, please contact our service center or the
store where you made your purchase at the latest
within 5 work days after purchasing the article and
upon presentation of a valid bill of purchase.
Open the packaging and take out the equip-
•
ment with care.
Remove the packaging material and any
•
packaging and/or transportation braces (if
present).
Check to see if all the items are supplied.
•
Inspect the equipment and accessories for
•
transport damage.
If possible, keep the packaging until the end
•
of the guarantee period.
Danger!
The equipment and packaging material are
not toys. Do not let children play with plastic
bags, plastic sheets and small parts. There is
a risk of choking and suff ocating!
Cordless worksite table saw
•
Saw blade guard
•
Push stick
•
Riving knife
•
Complete rip fence
•
Miter gauge
•
Extractor adapter
•
10/13 mm ring wrench
•
10/21 mm ring wrench
•
Original operating instruction with safety in-
•
formation
Separately available accessories
18V 1.5Ah PXC Lithium-Ion battery
18V 2.0Ah PXC Lithium-Ion battery
18V 2.5Ah PXC Lithium-Ion battery
18V 3.0Ah PXC Lithium-Ion battery
18V 4.0Ah PXC Lithium-Ion battery
18V 3.0Ah PXC Plus Lithium-Ion battery
18V 4.0Ah PXC Plus Lithium-Ion battery
18V 5.2Ah PXC Plus Lithium-Ion battery
18V 4.0Ah/6.0Ah PXC Plus Lithium-Ion battery
18V 5.0Ah/8.0Ah PXC Plus Lithium-Ion battery
18V PXC Dual Port Fast Charger
18V PXC Fast Charger
Contact your local retailer for more specifi c mo-
dels of batteries and charger available in your
area. You can also explore battery + charger options at Einhell.com.
3. Intended use
The cordless worksite table saw is designed for
the ripping and cross-cutting (only with the miter
gauge) of all types of timber commensurate with
the machine‘s size. The equipment is not to be
used for cutting any type of round wood.
The equipment is allowed to be used only for its
prescribed purpose. Any other use is deemed to
be a case of misuse. The user/operator and not
the manufacturer will be liable for any damage or
injuries of any kind resulting from such misuse.
Please note that our equipment has not been designed for use in commercial, trade or industrial
applications. Our warranty will be voided if the
equipment is used in commercial, trade or industrial businesses or for equivalent purposes.
To use the equipment properly you must also
observe the safety information, the assembly
instructions and the operating instructions to be
found in this manual.
All persons who use and service the equipment
have to be acquainted with these operating
instructions and must be informed about the
equipment‘s potential hazards. It is also imperative to observe the accident prevention regulations
in force in your area. The same applies for the
general rules of health and safety at work.
The manufacturer will not be liable for any changes made to the equipment nor for any damage
resulting from such changes. Even when the
equipment is used as prescribed it is still impossible to eliminate certain residual risk factors.
The following hazards may arise in connection
with the machine‘s construction and design:
Contact with the saw blade in the uncovered
•
saw zone.
Reaching into the running saw blade (cut
•
injuries).
Kick-back of workpieces and parts of work-
•
pieces.
Saw blade fracturing.
•
Catapulting of faulty carbide tips from the saw
•
blade.
Damage to hearing if essential ear-muffs are
•
not used.
Harmful emissions of wood dust when used
•
in closed rooms.
- 19 -
Anl_TE_TS_36_210_Li_USA_SPK7.indb 19Anl_TE_TS_36_210_Li_USA_SPK7.indb 19 07.10.2022 09:39:5807.10.2022 09:39:58
EN
4. Technical data
Motor power supply: ............................36 V
Idle speed n0: ...........................3800 RPM (min-1)
Carbide saw blade:
...........ø 8-
Number of teeth: ............................................ 40
Cutting height max. ................. 2-
............................................... 1-
Max. thickness of saw blade body:
....................................................0.047" (1.2 mm)
Height adjustment max. .................. 2-
Tilting saw blade max. ................................... 45°
Cross stop angle .............................. -60° to +60°
Extractor connection ...............Ø 1-⅜" (ø 36 mm)
Thickness of the splitter ..................
Weight (Tool only): .......................28.6 lbs (13 kg)
This machine is equipped with a special precision
cut saw blade (cutting width 0.071" (1.8 mm)). If
you use a diff erent saw blade with a larger cutting
width, this could result in loss of performance.
Wear ear-muff s.
The impact of noise can cause damage to hearing.
Reduce noise generation and vibration to a
minimum!
•
•
•
•
•
•
CAUTION!
Residual risks
Even if you use this electric power tool in
accordance with the instructions, certain
residual risks cannot be eliminated. The following hazards may arise in connection with
the equipment‘s con-struction and layout:
1. Lung damage if no suitable protective dust
2. Damage to hearing if no suitable ear protec-
1
⁄4" x 5⁄8" x 0.071" (ø 210 x 16 x 1.8 mm)
3
⁄4" (70 mm) / 90°
3
⁄4" (45 mm) / 45°
3
⁄4" (70 mm)
1
⁄16" (1.6 mm)
Use only equipment that is in perfect condition.
Maintain and clean the equipment regularly.
Adapt your way of working to the equipment.
Do not overload the equipment.
Have the equipment checked if necessary.
Switch off the equipment when not in use.
mask is used.
tion is applied.
Limit the operating time.
All stages of the operating cycle must be considered (for example, times in which the electric tools
are switched off and times in which the tool is
switched on but operates without load).
5. Before starting the equipment
Warning!
Always remove the battery before making adjustments to the equipment.
Unpack the bench-type table saw and check
•
it for damage which may have occurred in
transit.
The machine has to be set up where it can
•
stand firmly, e.g. on a work bench, or it must
be bolted to a strong base.
All covers and safety devices have to be pro-
•
perly fitted before the machine is switched on.
It must be possible for the saw blade to run
•
freely.
When working with wood that has been pro-
•
cessed before, watch out for foreign bodies
such as nails or screws etc.
Before you actuate the On/Off switch, make
•
sure that the saw blade is correctly fitted and
that the machine’s moving parts run smoothly.
6. Assembly
Danger! Remove the rechargeable battery before carrying out any maintenance, resetting
or assembly work on the table saw.
6.1 Standing the bench-type table saw upright (Fig. 4-6)
Fit the extractor adapter (16) at the back of
•
the machine. To do so, undo and remove
the recessed head screw (17) and push the
extractor adapter (16) onto the dust collector
(37). Secure the extractor adapter (16) and
dust collector (37) with the recessed head
screw (17).
Important! The two ring wrenches (30, 31)
•
can be stowed away on the side of the lower
saw blade cover (see Fig. 4). Keep the two
ring wrenches close to hand for fitting the table insert (6) and riving knife (5).
- 20 -
Anl_TE_TS_36_210_Li_USA_SPK7.indb 20Anl_TE_TS_36_210_Li_USA_SPK7.indb 20 07.10.2022 09:39:5807.10.2022 09:39:58
Loading...