EIC FBR5010, FBR5008, FBR5006, FBR5004, FBR5002 Datasheet

FBR5000 - FBR5010

FAST RECOVERY

PRV : 50 - 1000 Volts

Io : 50 Amperes

FEATURES :

* High case dielectric strength

MECHANICAL DATA :

MAXIMUM RATINGS AND ELECTRICAL CHARACTERISTICS

Rating at 25

°

C ambient temperature unless otherwise specified.

Single phase, half wave, 60 Hz, resistive or inductive load.

For capacitive load, derate current by 20%.

FBR

5000

FBR

5001

FBR

5002

FBR

5004

FBR

5006

FBR

5008

FBR

5010

Maximum Average Forward Current Tc = 55

C

I

A2S

Maximum DC Reverse Current Ta = 25

C

A

at Rated DC Blocking Voltage Ta = 100

C

Notes :

1 ) Measured with I

F

= 0.5 Amp., I

R

= 1 Amp., Irr = 0.25 Amp.

2 ) Thermal resistance from Junction to Case with units mounted on a 9"x5"x4.6" (22.9x12.7x11.7 cm) Al-Finned Heatsink.

BR50

0.530(13.40)

0.618(15.70)

1.120(28.40)

0.028(0.71)

* High surge current capability
* High reliability
* Low reverse current
* Low forward voltage drop
* Fast switching for high efficiency

* Case : Molded plastic with heatsink integrally
mounted in the bridge encapsulation
* Epoxy : UL94V-O rate flame retardant
* Terminals : plated .25" (6.35 mm). Faston
* Polarity : Polarity symbols marked on case
* Mounting position : Bolt down on heat-sink with
silicone thermal compound between bridge
and mounting surface for maximum heat
transfer efficiency.
* Weight : 17.1 grams

BRIDGE RECTIFIERS

0.728(18.50)

0.688(17.40)

0.570(14.50)

0.618(15.70)

0.032(0.81)

0.310(7.87)

0.280(7.11)

Metal Heatsink

0.685(16.70)

0.210(5.30)

0.200(5.10)0.658(16.70)

0.252(6.40)

0.248(6.30)

0.905(23.0)

0.826(21.0)

Dimensions in inches and ( millimeters )

1.130(28.70)

φ

0.100(2.50)

0.090(2.30)

RATING

Maximum Recurrent Peak Reverse Voltage VRRM 50 100 200 400 600 800 1000 Volts
Maximum RMS Voltage VRMS 35 70 140 280 420 560 700 Volts
Maximum DC Blocking Voltage VDC 50 100 200 400 600 800 1000 Volts

°

Peak Forward Surge Current Single half sine wave
Superimposed on rated load (JEDEC Method) I
Current Squared Time at t < 8.3 ms.
Maximum Forward Voltage drop per Diode at IF = 25 Amps. V

°

°

Maximum Reverse Recovery Time (Note 1) Trr 200 300 500 ns
Typical Thermal Resistance per diode (Note 2)
Operating Junction Temperature Range TJ - 50 to + 150 °
Storage Temperature Range TSTG - 50 to + 150 °

SYMBOL

IF(AV) 50 Amps.

FSM

2

t 664

F

R

I

R(H)

I

RθJC

400 Amps.

1.3 Volts
10

1.0 mA

1 °

UPDATE : NOVEMBER 1, 1998

UNIT

µ

C/W

C
C

RATING AND CHARACTERISTIC CURVES ( FBR5000 - FBR5010 )

+

4030201050

100101.0

400

0

0

300

200

100

0.11080

0.01

1.0

0.1

100

0204060120

+ 0.5 A0- 0.25

- 1.0 A

1 cm

FIG.1 - REVERSE RECOVERY TIME CHARACTERISTIC AND TEST CIRCUIT DIAGRAM

50 Ω 10 Ω

D.U.T.

50 Vdc

(approx)

1 Ω

NOTES : 1. Rise Time = 7 ns max., Input Impedance = 1 megaohm, 22 pF.

2. Rise time = 10 ns max., Source Impedance = 50 ohms.

3. All Resistors = Non-inductive Types.

OSCILLOSCOPE

( NOTE 1 )

PULSE

GENERATOR

( NOTE 2 )

Trr

SET TIME BASE FOR 50/200 ns/cm

FIG.2 - DERATING CURVE FOR OUTPUT FIG.3 - MAXIMUM NON-REPETITIVE PEAK
RECTIFIED CURRENT FORWARD SURGE CURRENT

500

Tc = 55 °C

CURRENT, AMPERES

AVERAGE FORWARD OUTPUT

60Hz RESISTIVE OR INDUCTIVE LOAD

0 25 50 75 100 125 150 175 1 2 4 6 10 20 40 60 100

CASE TEMPERATURE, ( °C)

CURRENT, AMPERES

PEAK FORWARD SURGE

NUMBER OF CYCLES AT 60Hz

FIG.4 - TYPICAL FORWARD CHARACTERISTICS FIG.5 - TYPICAL REVERSE CHARACTERISTICS
PER DIODE PER DIODE

TJ = 100 °C

TJ = 25 °C

Pulse Width = 300 µs

2% Duty Cycle

FORWARD CURRENT, AMPERES

TJ = 25 °C

REVERSE CURRENT, MICROAMPERES

PERCENT OF RATED REVERSE

140

VOLTAGE, (%)

0.01
0 0.2 0.4 0.6 0.8 1.0 1.2 1.4 1.6 1.8 2.0

FORWARD VOLTAGE, VOLTS