EIC BR2504W, BR2502W, BR2501W, BR2500W, BR2508W Datasheet

...

BR2500W - BR2510W

PRV : 50 - 1000 Volts

Io : 25 Amperes

FEATURES :

* High current capability

MECHANICAL DATA :

MAXIMUM RATINGS AND ELECTRICAL CHARACTERISTICS

Rating at 25

C ambient temperature unless otherwise specified.

Single phase, half wave, 60 Hz, resistive or inductive load.

For capacitive load, derate current by 20%.

MIN.

* High surge current capability * High reliability * Low reverse current * Low forward voltage drop * High case dielectric strength

SILICON BRIDGE RECTIFIERS

BR50W

0.732 (18.6)

0.692 (17.5)

1.130 (28.7)

1.120 (28.4)

0.470 (11.9)

0.430 (10.9)

0.21 (5.3)

0.20 (5.1)

* Case : Molded plastic with heatsink integrally mounted in the bridge encapsulation * Epoxy : UL94V-O rate flame retardant

0.042 (1.06)

0.038 (0.96)

1.2 (30.5)

* Terminals : Plated lead solderable per MIL-STD-202, Method 208 guaranteed * Polarity : Polarity symbols marked on case

0.310 (7.87)

0.280(7.11)

* Mounting position : Bolt down on heat-sink with silicone thermal compound between

Dimensions in inches and ( millimeters )

bridge and mounting surface for maximum heat transfer efficiency * Weight : 15.95 grams

RATING

Maximum Recurrent Peak Reverse Voltage VRRM 50 100 200 400 600 800 1000 Volts Maximum RMS Voltage VRMS 35 70 140 280 420 560 700 Volts Maximum DC Blocking Voltage VDC 50 100 200 400 600 800 1000 Volts Maximum Average Forward Current Tc = 55°C Peak Forward Surge Current Single half sine wave Superimposed on rated load (JEDEC Method) IFSM 300 Amp. Current Squared Time at t < 8.3 ms. I2t 375 A2S Maximum Forward Voltage per Diode at 12.5 Amp. VF 1.1 Volts Maximum DC Reverse Current Ta = 25 °C at Rated DC Blocking Voltage Ta = 100 °C Typical Thermal Resistance at Junction to Case ( Note 1 ) Typical Thermal Resistance at Junction to Ambient Operating Junction Temperature Range TJ - 40 to + 150 Storage Temperature Range TSTG - 40 to + 150

SYMBOL

IF(AV) 25 Amp.

RθJC RθJA

2500W

2501W

2502W

2504W

IR 10

IR(H) 1.0

2506W

2508W

2510W

UNIT

µA

°C/W °C/W

°C °C

Notes : 1 ) Thermal resistance from Junction to Case with units mounted on a 5" x 4" x 3" ( 12.7 x 10.2 x 7.3 cm ) Al.-wing plate.

UPDATE : APRIL 21, 1998

RATING AND CHARACTERISTIC CURVES ( BR2500W - BR2510W )

FIG.1 - DERATING CURVE FOR OUTPUT

FIG.2 - MAXIMUM NON-REPETITIVE PEAK

RECTIFIED CURRENT

FORWARD SURGE CURRENT

0.7

0.8

0.9

1.0

1.1

1.2

1.3

240

300

180

PERCENT OF RATED REVERSE

120

TJ = 55 °C

5.0

CURRENT, AMPERESFORWARD CURRENT, AMPERES

P.C. Board Mounted with

AVERAGE FORWARD OUTPUT

SINE WAVE R-Load free in AIR

0 25 50 75 100 125 150 175 1 2 4 6 10 20 40 60 100

CASE TEMPERATURE, ( °C)

CURRENT, AMPERES

PEAK FORWARD SURGE

8.3 ms SINGLE HALF SINE WAVE JEDEC METHOD

NUMBER OF CYCLES AT 60Hz

FIG.3 - TYPICAL FORWARD CHARACTERISTICS FIG.4 - TYPICAL REVERSE CHARACTERISTICS

100 10

Pulse Width = 300 µs

1.0

1 % Duty Cycle

1.0

0.1

MICROAMPERES

TJ = 100 °C

TJ = 25 °C

REVERSE CURRENT,

0.1

TJ = 25 °C

0.01 80

VOLTAGE, (%)

0.01

0.6

100 1400 20 40 60 120

FORWARD VOLTAGE, VOLTS