E-flite Mini Ultra Stick ARF Programming Guide

Programming Guide for the JR XP7202 for the Hangar 9 Ultra Stick

To start with, plug your servos into the correct channels. Below is a listing of what servo to plug
into each channel. You will need a 7-channel receiver to use the full set up that the 7202 is capable of
doing with the Ultra Stick.

Ch. 1 Throttle Ch. 5 Left Aileron (Listed as Gear Channel on Receiver)
Ch. 2 Right Aileron Ch. 6 Right Flap (Listed as Aux 1 on Receiver)
Ch. 3 Elevator Ch. 7 Left Flap (Listed as Aux 2 on Receiver)
Ch. 4 Rudder

System Set-Up Mode

To begin setting up the transmitter, press and hold the down and select keys, and turn the 7202
on, then release the down and select keys.

Model Selection

Press the up or down key until Model Select is on the top of the screen, and select the model you want
the ultra stick on by pressing the increase or decrease key.

Model Reset

Press the up key and scroll through the menu options until you get to Model Reset. With the arrow
pointing at data reset, press the clear key.

Model Type Selection

Press the down key until you get to the Type Select function. Press the increase or decrease button until
the arrow points at ACRO. If you change this from heli, it will then request you to press the clear key to
say yes to change the model type.

Modulation Selection

Set the modulation as needed to match your receiver by pressing the up key to get to the Modulation
function, and select the modulation needed by pressing the increase or decrease keys.

Input Select Set Up

Press the up key until you get to the Input Select function. With the arrow pointing at Aux2, press the
increase key until it says INH next to Aux2. Press the select key and the arrow should now point at

Aux2 Trim, this should say INH, if it does not, press the increase key until it does. Press the select key
again and the arrow should point at Flap. This should say SYSTEM, if it says something else, press the
increase key until this says SYSTEM. Press the select key, and the arrow should now point at flap trim.
Press the increase key to set this to INH

This completes the system set up mode, press the down and select keys to exit the system mode. Do not
activate flaperon in the wing type menu for this set up. All settings in the wing type menu will remain at
the default setting of OFF.

Function Mode

Next we will set up the function mode of transmitter. When you first turn the system on, the system will
request you to confirm the channel of operation by pressing the clear key. Once you have confirmed the
proper channel and have insured that no one else is on your frequency, press the clear key to use the
system. Press the up and select keys together to enter the function list. After completing each step
below, press the up and select keys to get back to the function list. To enter a function below from the
list on the system, press the down and select keys together with the arrow pointing at that function.

Dual Aileron Set Up

To set up the dual ailerons, we will set up a program mix. We will use program mix 5 for this purpose.
Enter program mix 5. Press the increase key until the first channel says AILE. Then press the select key
to make the arrow point at the second channel, then press the increase key until the second channel says
GEAR. Press the select key to make the arrow point at RATE, then hold left aileron and press the
increase key until the percentage says +100%. Then hold right aileron and press the increase key until
the second percentage says +100% as well. Both values should say +100%. Next to SW on the screen it
should say ON. If it says something other than ON, press the select key to make the arrow point at SW,
and press the increase key until it says ON.

Dual Flap Set Up

To set up the dual flaps, we will set up a program mix. We will use program mix 6 for this purpose.
Enter program mix 6. Press the increase key until the first channel says FLAP. Then press the select
key to make the arrow point at the second channel, then press the increase key until the second channel
says AUX2. Press the select key to make the arrow point at RATE, then press the increase key until the
percentage says +100%. Then flip the flap switch until the arrow moves to the second mix value, and
press the increase key until the second percentage says +100% as well. Both values should say +100%.
Next to SW on the screen it should say ON, if it says something other than ON, press the select key to
make the arrow point at SW, and press the increase key until it says ON.

Dual Rates and Expo

Set your Dual Rates and Expo as you desire. Enter the D/R & EXP function. Set these as desired.
Always use a positive value for expo, as a negative value will make the control response more sensitive
around center and could cause you to over control the plane and crash. 30 percent expo on aileron, and