EchoStar DVR-5000 HDD Viaccess, DVR-7000 HDD Supplementary Manual

Service Letter

EchoNAV software version 2.2

EchoNAV User Interface

for Digital Satellite Receivers

HDD

Printed on recycled paper

Issue: echonav_hdd_sl_22a_us

We encourage you to express your thoughts on this service letter.

Please send your comments to:

EchoStar International Corporation

Technical Publications Department

Schuilenburglaan 5a

7604 BJ Almelo

The Netherlands

PREFACE

1. DEAR CUSTOMER

This service letter introduces version 2.2 for the EchoNAV user interface which supersedes the previous service letter(s). For your convenience the highlights of the previous software are also given.

THE HIGHLIGHTS FOR VERSION 2.2

■ Two menu languages added;

■ Revised help lines and related translations;

■ Revised subtitle behaviour;

■ Russian and Greek subtitle languages added;

■ Multilingual EPG language support added;

■ Revised conditional access to support smartcards type PC2.4;

■ Revised channel numbering for Current SAT list;

■ New installation menus added for multiple LNB support;

■ Revised Add SAT, TP and PID menus;

■ Pre-defined LNB (LO 10,700) added to LNB list;

■ User LNB settings menu are moved to the Advanced mode;

■ New option to add satellite or transponder during initial installation setup added;

■ OTA service added on ASTRA1, 19.2 East.

■ DVR timer modified to allow for recording a relative time block.

■ Updated satellite/transponder database

Preface

THE HIGHLIGHTS FOR PREVIOUS VERSION 2.0

■ Six menu languages added;

■ Group and Sort behaviour revised to remember the last setting;

■ Extended channel information available with i-key;

■ Move function extended with recall option;

■ Edit functions, Move, Lock and Delete separated;

■ Save changes pop-up menu added.

■ Updated satellite/transponder database

DVR-7000 HDD ONLY

■

Photo album added;

■ New MP3Loader made available with embedded BackgroundLoader and PhotoLoader;

■ Installation menu added for Set East and West Limit;

■ Improved positioner behaviour.

2. INTENDED USE

This service letter is intended for anyone who uses an EchoStar satellite receiver with an EchoNAv user interface. It can be used by both first-time and experienced users who want to install, use and maintain their receiver.

This service letter is applicable for the Digital Satellite Receiver with Hard Disk:

■ DVR-7000 HDD Viaccess;

■ DVR-7000 HDD;

■ DVR-5000 HDD Viaccess;

■ DVR-5000 HDD.

This service letter is divided into separate sections and chapters for easy reference to the applicable chapters of your user manual. Please keep this service letter next to your user manual for future reference.

EchoNAV 2.2 Page I

Preface

3. DISCLAIMER

SATELLITE RECEIVER

EchoStar International Corporation has done everything to the best of her abilities, to supply you with a satellite receiver built to the most up-to-date software and hardware. EchoStar International Corporation makes no warranties with respect to the reception of the channels provided by the broadcast service providers and specifically disclaims any implied warranties of merchantability or fitness for any particular purpose.

EchoStar International Corporation reserves the right, for whatever reason, to revise, change or modify the hard- and software of the satellite receiver without the obligation to notify or warrant any person or organization of such change. Therefore, please visit our website, on a regular basis, for the latest information available.

SOFTWARE DOWNLOADS

EchoStar International Corporation will do everything to the best of her abilities, to supply you with software updates to keep your receiver as up-to-date as technically possible. EchoStar International Corporation makes no warranties with respect to the use of the supplied software downloads and specifically disclaims any implied warranties of merchantability or fitness for any particular purpose.

EchoStar International Corporation reserves the right, for whatever reason, to revise, change or modify the software that can be used by your satellite receiver without the obligation to notify or warrant any person or organization of such change. Therefore, please visit our website, on a regular basis, for the latest software available.

SERVICE LETTER

EchoStar International Corporation has done everything to the best of her abilities, to supply you with the most up-to-date information. EchoStar International Corporation makes no warranties with respect to the information provided by this service letter and specifically disclaims any implied warranties of merchantability or fitness for any particular purpose. The information provided is meant as a guideline for the use and maintenance of the receiver.

EchoStar International Corporation reserves the right to right, for whatever reason, change or translate this service letter without the obligation to notify any person or organization of such change. Therefore, please visit our website, on a regular basis, for the latest information available.

Page II EchoStar International Corporation

Preface

TABLE OF CONTENTS

Preface

1 DEAR CUSTOMER I 2 INTENDED USE I 3DISCLAIMER II

Installation

1 TO SETUP YOUR RECEIVER FOR THE FIRST TIME 3-1 2 ADVANCED MODE (MULTIPLE LNB SUPPORT) 3-7

Familiarization

1 ECHONAV 2.2 4-1 2 THE ECHONAV INSTALLATION MENU 4-3 3 THE ECHONAV MODE AND SELECTION MENUS 4-10 4 THE INDEX MARKERS 4-13 5 THE TIMERS 4-14

Operation

1 TO NAVIGATE THROUGH THE MENUS 5-1 2 USE THE FAVORITE LISTS 5-5 3 TO SELECT ANOTHER SATELLITE 5-6 4 TO USE THE INDEX MARKERS 5-6 5 TO USE THE PHOTO ALBUM 5-8 6 TO USE THE DVR STOP TIMER 5-9

Maintenance

1 USER LNB SETTING - SUB-MENU (ADVANCED ONLY) 6-1

2 SET LIMITS - SUB-MENU 6-1 3 SEARCH CHANNELS - ANALOG IF 6-2 4 ADD DATA (SAT/TP) - SUB-MENU 6-2

Troubleshooting

1 TO SOLVE AN INSTALLATION RELATED PROBLEM 7-1

Glossary

1 LIST OF USED ABBREVIATIONS 8-1 2 EXPLANATION OF USED TERMINOLOGY 8-2

Index

Appendix 1

1 LNB CONFIGURATION MATRIX A1-1 2 LNBF CONFIGURATION MATRIX A1-1 3 USER DEFINED LNB(F) MATRIX A1-2

EchoNAV 2.2 Page III

Preface

Page IV EchoStar International Corporation

Installation

INSTALLATION

Section 3

1. TO SETUP YOUR RECEIVER FOR THE FIRST TIME

This procedure supersedes the procedure as given in the user manual from step 15 onwards. The main differences are:

■ Select Easy or Advanced installation,

Easy installation helps you to do the initial setup procedure where Advanced allows you to program the receiver as required for non-standard installations.

■ Add a new satellite,

In a satellite field you can select any known satellite in range from the database or add your own defined satellite with the use of the S00 satellite.

■ Add a new transponder,

In a transponder field you can select any known transponder from the database or add your own defined transponder with the use of the TP00 transponder.

NOTE

From the next step onwards, the procedure is divided in different configurations. The configurations are; Fixed, Motorized and SMATV.

■ Fixed means set up a single dish or multiple dishes with DiSEqC1..4 switch;

■ Motorized means set up a moveable dish (motor/actuator by positioner);

■ SMATV means set up for television distribution (cable network in buildings).

3

FOR ALL CONFIGURATIONS

1. Make the required selections.

2. Read the available help text for information.

3. Go to the Save settings field to confirm the time.

4. On the RCU, press the OK key to set the time. Note that the local time is shown correctly.

5. Go to the Continue field.

6. On the RCU, press the OK key to advance

FOR FIXED AND DISEQC 1..4 SWITCH CONFIGURATIONS - EASY

21. Make the required selections.

22. Set the required installation mode, recommended setting is Easy (guided setup procedure).

23. Read the available help text for information. Note that only the white fields are selectable, other fields show reference information.

24. If you want to add your own defined satellite, go to the SAT field and select S00 (Goes to the menu where you can define your own satellite, for detailed information, refer to section 6). If not proceed with step 25.

25. Go to the Check signal field.

26. On the RCU, press the OK key to advance.

EchoStar International Corporation Page 3 - 1

Section 3

27. Wait for the Checking configuration to complete.

28. Read the available help text for information.

29. Make the required selections.

30. If the red dot in the TP field stays:

31. If you want to add your own defined transponder,

32. Go to the Search channels field.

33. On the RCU, press the OK key to advance.

Installation

a. select another transponder; b. go to the Check signal field; c. on the RCU, press the OK key.

go to the TP field and select TP00 (Goes to the menu where you can define your own transponder, for detailed information, refer to section 6). If not proceed with step 32.

34. Wait for the search to complete: a. the receiver display shows a moving dot; b. the Search completed popup menu appears.

35. On the RCU, press the OK key to end the initial setup procedure.

FOR MOVEABLE DISH INSTALLATIONS (DISEQC 1.2)

21. Make the required selections.

22. Set the required installation mode, recommended setting is Easy (guided setup procedure).

23. Read the available help text for information. Note that only the white fields are selectable, other fields show reference information.

24. Go to the Program Satellites field.

25. On the RCU, press the OK key to advance.

26. Select the satellite which you want to receive.

27. Read the available help text for information. Note that only the white fields are selectable, other fields show reference information.

28. If you want to add your own defined satellite, go to the SAT field and select S00 (Goes to the menu where you can define your own satellite, for detailed information, refer to section 6. If not proceed with step 34.

Page 3 - 2 EchoNAV 2.2

29. When in the Position field: a. press and hold theor key and watch the

signal indicator for an indication;

b. in the signal indicator, make sure a network

name is shown;

c. press thekey to select another transponder for

signal verification; d. press thekey to select the Position field; e. use thekey to fine tune for the best signal

level and quality; f. press the OK key, note that the saved position of

the satellite is shown.

30. If you want to add your own defined transponder for the selected satellite, go to the TP field and select TP00 (Goes to the menu where you can define your own transponder, for detailed information, refer to section 6). If not proceed with step 36.

31. Go to the Search channels field.

32. On the RCU, press the OK key to advance.

Installation

Section 3

3

33. Wait for the search to complete: a. the receiver display shows a moving dot; b. the search completed popup menu appears.

34. On the RCU, press the OK key. to end the initial setup procedure.

FOR MOTORIZED CONFIGURATIONS - AUTOSAT

CAUTION

On the motorized dish, set the physical East and West limit switches first. Failing to do so might cause damage to your motorized dish installation or other properties.

21. Make the required selections.

22. Set the required installation mode, recommended setting is Easy (guided setup procedure).

23. Read the available help text for information. Note that only the white fields are selectable, other fields show reference information.

24. Go to the Autosat field.

25. On the RCU, press the OK key to advance.

EchoStar International Corporation Page 3 - 3

Section 3

26. On the RCU:

27. On the RCU, press the OK key.

28. Select the most East SAT which you can receive.

29. If you want to add your own defined East SAT,

Installation

a. press thekey to set the EL (East limit); b. at the Motor error, press thekey once; c. press the OK key.

select S00 (Goes to the menu where you can define your own satellite, for detailed information, refer to section 6). If not proceed with step 31.

30. If you want to add your own defined transponder for the selected satellite, go to the TP field and select TP00 (Goes to the menu where you can define your own transponder, for detailed information, refer to section 6). If not proceed with step 31.

31. When in the Position field: a. press and hold thekey and watch the signal

indicator for an indication;

b. in the signal indicator, make sure a network

name is shown;

c. press thekey to select another transponder for

signal verification; d. press thekey to select the Position field; e. use thekey to fine tune for the best signal

level and quality; f. press the OK key, note that the saved position of

the satellite is shown.

32. Repeat the procedure for the middle and most West SAT.

33. Set the WL (key), refer to step 26.

34. Go to the SAT list field.

35. On the RCU, press the OK key to advance.

Page 3 - 4 EchoNAV 2.2

36. Make the required selections.

37. Read the available help text for information.

38. Go to the Search channels field.

39. On the RCU, press the OK key to advance.

40. Wait for the search to complete: a. the receiver display shows a moving dot; b. the Search completed popup menu appears.

41. On the RCU, press the OK key to end the initial setup procedure.

Installation

Section 3

3

FOR MOTORIZED CONFIGURATIONS - MANUAL SELECTION

CAUTION

On the motorized dish, set the physical East and West limit switches first. Failing to do so might cause damage to your motorized dish installation or other properties.

21. Make the required selections.

22. Set the required installation mode, recommended

setting is Easy (guided setup procedure).

23. Read the available help text for information. Note that only the white fields are selectable, other fields show reference information.

24. Go to the Method field and select Manual.

25. Go to the Set limits field.

26. On the RCU, press the OK key to advance.

EchoStar International Corporation Page 3 - 5

Section 3

27. On the RCU:

28. On the RCU:

29. Go to the Program satellites field.

30. On the RCU, press the OK key to advance.

31. Select the satellite which you want to receive.

32. Read the available help text for information.

33. If you want to add your own defined satellite, go to

Installation

a. press thekey to set the EL (East limit); b. at the Motor error, press thekey once; c. press the OK key.

a. press thekey to set the WL (west limit); b. at the Motor error, press thekey once; c. press the OK key.

Note that only the white fields are selectable, other fields show reference information.

the SAT field and select S00 (Goes to the menu where you can define your own satellite, for detailed information, refer to section 6. If not proceed with step 34.

34. When in the Position field: a. press and hold theor key and watch the

signal indicator for an indication;

b. in the signal indicator, make sure a network

name is shown;

c. press thekey to select another transponder for

signal verification; d. press thekey to select the Position field; e. use thekey to fine tune for the best signal

level and quality; f. press the OK key, note that the saved position of

the satellite is shown.

35. If you want to add your own defined transponder for the selected satellite, go to the TP field and select TP00 (Goes to the menu where you can define your own transponder, for detailed information, refer to section 6). If not proceed with step 36.

36. Go to the Search channels field.

37. On the RCU, press the OK key to advance.

38. Wait for the search to complete: a. the receiver display shows a moving dot; b. the Search completed popup menu appears.

39. On the RCU, press the OK key to end the initial setup procedure.

Page 3 - 6 EchoNAV 2.2

FOR SMATV CONFIGURATIONS

21. Make the required selections. After the initial installation it is possible to add more symbol rates. Refer to section Maintenance for detailed instructions.

22. Read the available help text for information.

23. Go to the Search Channels field.

24. On the RCU, press the OK key to advance.

25. Wait for the search to complete: a. the receiver display shows a moving dot; b. the Search completed popup menu appears.

26. On the RCU, press the OK key to end the initial setup procedure.

Installation

Section 3

3

2. ADVANCED MODE (MULTIPLE LNB SUPPORT)

21. Make the required selections.

22. Use thekey to set the installation mode to Advanced.

23. Note that the screen changes into the advanced

mode.

24. .If you want to return to the Easy mode, use thekey to set the installation mode to Easy.

25. Read the available help text for information.

26. Go to the Set limits field.

27. On the RCU, press the OK key to advance.

28. Read the available help text for information.

29. Make the required selections.

30. Go to the Program satellites field.

31. On the RCU, press the OK key to advance.

EchoStar International Corporation Page 3 - 7

Section 3

32. Select the satellite which you want to receive.

33. Read the available help text for information.

34. If you want to add your own defined satellite, go to

35. Go to the User LNB field and on the RCU press the

36. Note that the software advances to the

37. Read the available help text for information.

38. Make the required selections.

39. Go to the Save settings field.

40. On the RCU, press the OK key to advance.

41. Note that the software returns to the Program

Installation

Note that only the white fields are selectable, other fields show reference information.

the SAT field and select S00 (Goes to the menu where you can define your own satellite, for detailed information, refer to section 6).

i-key.

User LNB setting menu.

satellites menu.

42. Make the required selections.

43. If you want to add your own defined transponder for the selected satellite, go to the TP field and select TP00 (Goes to the menu where you can define your own transponder, for detailed information, refer to section 6).

44. Go to the Search channels field.

45. On the RCU, press the OK key to advance.

46. Wait for the search to complete: a. the receiver display shows a moving dot; b. the Search completed popup menu appears.

47. On the RCU, press the OK key to end the initial setup procedure.

Page 3 - 8 EchoNAV 2.2

Familiarization

FAMILIARIZATION

Section 4

1. ECHONAV 2.2

The software of the receiver contains the EchoNAV user interface with on-screen help, which gives you easy control over the features of the receiver. The software contains also a large database of pre-programmed satellites and transponders which are used for a quick installation. For initial installation, the software guides you through the required setup menu to allow for an easy and reliable installation setup of the receiver.

FEATURE HIGHLIGHTS

The highlights for this version are:

■ New menu languages added;

Portuguese, Dutch.

■ Revised help lines and related translations;

All menu texts are revised to give more support and information. All menu languages are translated accordingly.

■ Several small menu changes incorporated:

- LNB power option in system setup menu for SMATV deleted,

- Time zone option in Local time menu deleted,

- Software identification in About EchoStar menu is changed to show EchoNAV version.

■ Revised subtitle behavior;

Greek and Russian subtitle support is added.

■ Multi-lingual language support for EPG added;

If available form the service provider, EPG language is shown in the language which is set for the menu language (user preferences - Languages - Menu).

■ Revised conditional access to support smartcards type PC2.4;

The embedded Viaccess smartcard reader is revised to support the latest generation of PC2.4 smartcards as used by several service providers who use Viaccess encryption.

■ Revised channel numbering for Current SAT list;

The Current SAT list is revised to have it’s own channel numbering. Therefore the channel numbering (only for Current SAT) starts at 1 for each satellite. Note that also the satellite

name is shown permanently.

■ New installation menus added for multiple LNB support;

The installation menu is revised to support Easy and Advanced installation. In the

advanced installation you can define user defined LNBs where the Easy installation allows for the installation of pre-defined LNBs.

■ Revised Add SAT, TP and PID menus;

The Add SAT, Add TP, and Add PID are combined in one menu Add data.

■ New option to add satellite or transponder during initial installation setup added;

Add Data menu is accessible from the initial setup and after installation from the channel list through the ‘white edit’ menu.

■ OTA service added on ASTRA1, 19.2 East.

■ DVR timer modified to allow for recording a relative time block;

The DVR timer is directly accessible after a recording is started. You can set the stop time either in absolute time (13:00 hr) or relative time (+ 00:15 min).

■ Updated satellite/transponder database,

You have to perform a factory reset to activate the database, failing to do so keeps the previous database active.

4

EchoStar International Corporation Page 4 - 1

Section 4

Familiarization

1.1. THE REMOTE CONTROL UNIT (RCU)

The EchoStar Quattro is a programmable RCU that also can control your TV, VCR, DVD and/or Audio set. The EchoStar Quattro requires two AA/R6 alkaline batteries to operate.

■ ON/STANDBY

To switch to standby or on.

■ VCR

To control the VCR.

■ TV

To control the TV.

■ EPG

To view the EPG.

■ MENU

To go to the installation menu; To go to the special functions.

■ VOL+

To increase the volume.

■ VOL-

To decrease the volume.

■ ARROW CLUSTER

To scroll left, up, right or down.

■ EXIT

To leave a menu or feature.

■ PAGE +

To go one page up.

■ PAGE -

To go one page down.

■ ALT AUDIO

To choose a language.

■ ALT SUBTITLE

To choose a subtitle.

■ STOP

To stop the recording or play back of an event; To return to actual time in the EPG window

■ REWIND

To go to the beginning of an recorded event fastly.

■ RECORD (press twice)

To record a live program. To show the DVR stop timer.

■ PREVIOUS

To go to the previous event.

■ GREEN

To select a (favorites) list.

■ RED

To go to another mode.

■ NUMBER KEYS

To enter numerical settings; To type in a channel number.

■ TV/RAD

To switch to TV or Radio mode.

■ MUTE

To blank out the volume.

■ AUX

To control the Audio Set or DVD.

■ SAT

To control the receiver.

■ i

To view the InfoBanner; To view detailed EPG information.

■ Satellite Dish

To select another satellite.

■ CH+

To go one channel up.

■ CH-

To go one channel down.

■ OK

To go to the (favorites) lists; To make a menu selection; To pull down a selection menu.

■ RECALL

To go to the previous channel;

■ ?

Not used for Sat-mode.

■ V (white)

To edit a list

■ PLAY

To play back a recorded event.

■ FAST FORWARD

To go to the end of an recorded event fastly.

■ PAUSE

To pause the playback of an event; To pause a live program.

■ NEXT

To go to the next event.

■ YELLOW

To group a list; To select an EPG timer.

■ BLUE

To sort a list; To zoom in/out the time slot of the EPG view window.

■ FAV

To go to the favorite list of the actual mode.

Page 4 - 2 EchoNAV 2.2

Familiarization

2. THE ECHONAV INSTALLATION MENU

A highlighted button shows you which (main/sub) menu is selected. The MENU key lets you change between the main and sub-menu where thekeys let you make a selection in the selected (main/sub) menu. The OK key brings you into the related page, where you can make

a choice from the available options.

NOTE

Once in a page, at any time:

■ you can use the MENU key to reverse from a menu page to the sub-menu bar;

■ you can easily leave with the EXIT key.

■ The button, that gives you access to the User Preferences menu;

■ The button, that gives you access to the installation setup menu;

■ The button, that gives you access to the Conditional Access menu.

2.1. THE USER PREFERENCES MENU

This main menu has different sub-menus that give access to the pages where you can customize the factory settings. The user preferences menu always comes in view with the User Profile sub-menu. In the menu bar the sub menus are shown at the right side. The available sub menus are shown as icons which become a highlighted button after selection. The sub-menus are accessible with:

Section 4

4

■ The button, that gives you access to the User Profile page.

■ The button, that gives you access to the Languages page.

■ The button, that gives you access to the Parental Lock page.

■ The button, that gives you access to the Local Time page.

■ The button, that gives you access to the TV System page.

2.1.1. USER PROFILE SUB-MENU

This sub-menu allows you to customize the user profile settings, you can customize:

■ Aspect ratio

To set the screen size of the TV.

■ InfoBanner time-out

To select the view time for the InfoBanner.

■ Dolby Digital

To tell the receiver that it is connected to a Dolby Digital amplifier or not.

■ RGB-Sync

To switch the RGB-sync signal, which is required by monitors only, to On (monitor) or Off (TV).

■ Backgrounds

To select the standard or a personal background color.

EchoStar International Corporation Page 4 - 3

Section 4

Familiarization

2.1.2. LOCAL TIME SUB-MENU

This sub-menu allows you to customize the local time settings. For the correct operation of the EPG and the timers, it is necessary to set the local time correctly. You can customize:

■ Year

To set the actual year.

■ Month

To set the actual month.

■ Date

To set the actual date.

■ Day

To set the actual day.

■ Hour

To set the actual time in hours.

■ Minute

To set the actual time in minutes.

■ Save settings

To confirm the settings you made.

2.2. THE INSTALLATION SETUP MENU

This main menu has different sub-menus that give access to the pages where you can customize the settings to match your personal requirements. Note that the sub-menus are dynamic which means that they change with the selections you make. The installation setup menu always comes in view with the system setup sub-menu. In the menu bar the sub menus are shown at the right side. The available sub menus are shown as icons which become a highlighted button after selection. The sub-menus are accessible with:

■ The button, that gives you access to the System Setup page (for Fixed dish, SMATV);

■ The button, that gives you access to the System Setup page (for motorized dish);

■ The button, that gives you access to the Program Satellites page (for motorized dish);

■ The button, that gives you access to the User LNB Setting page (For Advanced only);

■ The button, that gives you access to the Set East/West Limit page;

■ The button, that gives you access to the About EchoStar information page;

■ The button, that gives you access to the System Upgrade page;

■ The button, that gives you access to the Factory Reset page.

Page 4 - 4 EchoNAV 2.2

Familiarization

Section 4

2.2.1. SYSTEM SETUP SUB-MENU - EASY

DVR-7000 HDD

This sub-menu allows you to customize the system setup to match your installation. Note that the menu page is dynamic which means that it changes with the selections you make. You can customize:

ONLY

■ System

To select the dish type you use.

■ Installation (fixed, motorized only)

To select the guided setup procedure for Easy installations or Advanced installations with multiple user defined LNBs.

■ LNBs

To set the amount of LNBs you have installed.

■ Polarity

To set the device that controls the signal polarity.

■ Switch

To set the switch type which you use to control the dish installation (if used).

■ LNB1

To set the LNB type(s) you use.

■ SAT (for fixed only)

To select the satellite you want to scan for the LNB. Satellite S00 brings you to the add data menu.

■ Method (for motorized only)

To set the channel search method; AutoSat (automatically calculate the satellite positions from reference positions) Manual (enter the satellites by manual search).

■ AutoSat (for motorized, AutoSat only)

To confirm the selections you made and advance to the AutoSat setup page (AutoSat only)

■ Set limits (for motorized, manual only)

To confirm the selections you made and advance to the Set limits page.

■ Check signal (for fixed only)

To confirm the selections you made and advance to the Check signal page.

■ Symbol rate1-4 (for SMATV only)

To set the symbol rate you want to scan.

■ Search channels (for SMATV only)

To confirm the selections you made and advance to the Search channels page.

4

EchoStar International Corporation Page 4 - 5

Section 4

DVR-5000 HDD ONLY

This sub-menu allows you to customize the system setup to match your installation. Note that the menu page is dynamic which means that it changes with the selections you make. You can customize:

Familiarization

■ System

To select the dish type you use.

■ Installation (fixed, DiSEqC 1.2 only)

To select the guided setup procedure for Easy installations or Advanced installations with multiple user defined LNBs.

■ LNBs

To set the amount of LNBs you have installed.

■ Polarity

To set the device that controls the signal polarity.

■ Switch

To set the switch type which you use to control the dish installation (if used).

■ LNB1

To set the LNB type(s) you use.

■ Program Satellites (DiSEqC1.2 only)

To confirm the selections and go to next menu.

■ SAT (for fixed only)

To select the satellite you want to scan for the LNB. Satellite S00 brings you to the add data menu.

■ Check signal (for fixed only)

To confirm the selections you made and advance to the Check signal page.

■ Symbol rate1-4 (for SMATV only)

To set the symbol rate you want to scan.

■ Search channels (for SMATV only)

To confirm the selections you made and advance to the Search channels page.

Page 4 - 6 EchoNAV 2.2

2.2.2. FIXED DISH SETUP - SUB-MENU

This sub-menu allows you to customize the system setup to add an additional fixed dish into your motorized or DiSEqC1.2 configuration. Note that the menu page is dynamic which means that it changes with the selections you make. You can customize:

■ LNBs

■ Polarity (DVR-7000 series only)

■ Switch

■ LNB1

■ LNB2, LNB3, LNB4

■ SAT

■ Port

■ Check signal

Familiarization

Section 4

To set the amount of LNBs you have installed.

To set the device that controls the signal polarity.

Shows the switch type which you use to control the dish installation.

Shows the LNB type which you use on the motorized dish.

To set the LNB type(s) you use on the fixed dish(es).

To select the satellite you want to scan for the LNB. Satellite S00 brings you to the add data menu.

To select the switch port for the LNB.

To confirm the selections you made and advance to the Check signal page.

4

2.2.3. PROGRAM SATELLITES - SUB-MENU

This sub-menu allows you to customize the system setup to add an additional satellite into your receiver. Note that the menu page is dynamic which means that it changes with the

selections you make. You can customize and view:

■ SAT

To select the satellite you want to scan for the LNB. Satellite S00 brings you to the add data menu.

■ Search mode (for digital receivers only)

To set a specific search mode (All, FTA, IF, TP, network or update).

■ Search mode (for analog/digital receivers only)

To set a specific search mode (All, FTA, network, TP, Digital, Analog, Digital IF, Analog IF or update).

■ Longitude

To view the satellite location on the Clarke Belt.

■ User LNB

Shows the LNB type which you use on the motorized dish.

EchoStar International Corporation Page 4 - 7

Section 4

MOTORIZED CONFIGURATION ONLY

DISEQC1.2 CONFIGURATION ONLY

Familiarization

TP

■

To select a transponder of the selected satellite. Transponder TP00 brings you to the add data menu.

■ Skew (for polarotor only)

To adjust the Horizontal/Vertical setting.

■ Position

To move the dish for best signal level and quality.

■ Re-align dish

To compensate for a dish offset caused by ambient conditions.

NOTE

A re-align dish will affect all satellite positions, this means that all scanned positions will change which might result in total loss of signal for all satellites.

■ Search channels

To confirm the selections you made and advance to the Search channels page.

■

TP To select a transponder of the selected satellite. Transponder TP00 brings you to the add data menu.

■ Position

To move the dish for best signal level and quality.

■ Fine tune

To move the dish slowly for best signal level and quality.

■ Search channels

To confirm the selections you made and advance to the Search channels page.

2.2.4. SET LIMITS - SUB-MENU

CAUTION

On the motorized dish, set the physical East and West limit switches first. Failing to do so might cause damage to your motorized dish installation or other properties.

This sub-menu allows you to change the present selected East or West Limit. The selections in this menu only set the limits electronically which means that you also must change the physical East and West limit switches on the dish itself. Be aware that electronically selected limits are lost when you do a factory reset.

■ EL

To electronically set the East Limit for the dish.

■ WL

To electronically set the West Limit for the dish.

■ Program Satellites

To advance to the next menu.

Page 4 - 8 EchoNAV 2.2

Familiarization

Section 4

2.2.5. ABOUT ECHOSTAR - INFORMATION PAGE

The About EchoStar information page gives all the where-to-contact-Information about EchoStar and the status information about the receiver. You can view:

■ Company

This field shows the full name of EchoStar.

■ Address

This field shows the address of EchoStar.

■ EchoNAV

This field shows the current software version loaded into the receiver.

■ Boot version

This field shows the current boot version loaded into the receiver.

■ Internet site

This field shows the EchoStar web site where you can find the latest user and software information.

2.2.6. SOFTWARE UPGRADE - SUB-MENU

This sub-menu allows you to upgrade the receiver’s software. EchoStar provides free-of-charge software updates Over-The-Air (OTA) which means that you can upgrade your system via the satellite.

If you are not able to receive the satellite/transponder, you always can free-of-charge, upgrade the software through the SERIAL PORT (RS-232) at the rear of the receiver with use of the dedicated EchoNAV Loader and the downloaded software from the EchoStar website.

Read the enclosed instructions of the downloaded file before you use the EchoNAVLoader.

■ OTA settings

To select a default (selection Factory1 for Hotbird or Factory 2 for Astra1) or user defined satellite where you want to download from.

■ SAT

To set the satellite where you want to download from.

■ Frequency

To set the transponder where you want to download from.

■ Polarity

To set the correct polarity for the transponder.

■ Symbol rate

To set the correct symbol rate for the transponder.

■ FEC

To set the correct Forward Error Correction for the transponder.

■ Start

To execute the system upgrade, download the new software (if available) from the satellite and load it into the receiver automatically.

■ The signal indicator

- The top bar shows the signal level to indicate that you receive a signal.

- The bottom bar shows the quality of the signal (signal-to-noise ratio) to indicate that you have a lock onto the selected transponder.

- The bottom text gives the satellite and network information to which the lock is established.

4

EchoStar International Corporation Page 4 - 9

Section 4

Familiarization

2.2.7. FACTORY RESET - SUB-MENU

This sub-menu allows you to reset the receiver to the initial factory settings. The Memory User settings option restores the factory settings over your personal settings. All personal settings like parental control and favorites will be replaced with the factory default settings.

■ Memory - User settings

To instruct the receiver to delete all personal settings and restore the factory default settings.

■ Hard disk - Recordings

To instruct the receiver to delete (only) all TV and Radio recordings from the hard disk.

■ Hard disk - MP3 Songs (DVR-7000 series only)

To instruct the receiver to delete (only) all MP3 songs from the hard disk.

■ Hard disk - Backgrounds

To instruct the receiver to delete (only) all the personal backgrounds from the hard disk.

■ Hard disk - EPG Data

To instruct the receiver to delete (only) all scheduled EPG data from the hard disk.

■ Hard disk - Photos (DVR-7000 series only)

To instruct the receiver to delete (only) all photos from the hard disk.

■ Confirm

With this field you can confirm the selection made and execute the selected procedure. After the erase procedure is finished, you are taken to the initial setup procedure. (for detailed instructions, please refer to section Installation).

3. THE ECHONAV MODE AND SELECTION MENUS

3.1. GROUP AND SORT

Once in a list, the selection for Group (yellow key) and Sort (blue key) are kept until you change the selection. The selection is made visible in the InfoBanner with icons

NOTE

Sometimes a list seems to be empty because of the settings of the Group and Sort option. If this happens, select Group - None and Sort - None.

3.2. EDIT

When in the edit menu, the Move, Lock and Delete option gives only access to the related function.

3.2.1. MOVE

When in the edit menu, you can select the move option only with Group and Sort set to none. You can move the selected channel manually or by number. After the move action you can press the recall key to go to the location where you started the move action.

■ White;

To select the Move option.

■ Red bullet;

To indicate that the selection is active.

■ Numerical field;

To enter the channel number where you want to move to.

Page 4 - 10 EchoNAV 2.2

■ On the RCU, the key;

To return to the previous location in the list.

3.2.2. LOCK

3.2.3. DELETE

Familiarization

■ White;

To select the Lock option.

■ Red bullet;

To indicate that the selection is active.

■ White;

To select the Delete option.

■ Red bullet;

To indicate that the selection is active.

Section 4

4

3.2.4. DO YOU WANT TO SAVE CHANGES?

At several locations in the software where you can make changes to selections, you are asked if you want to save or discard the changes.

■ Yes;

to save changes and return to list;

■ No;

3.3. THE INFOBANNER

3.3.1. LIST ICONS

The TV InfoBanner shows the information related to the actual channel. Only the new introduced icons are discussed.

to forget changes and return to list.

■ The i-button, to indicate that there is detailed program information available;

■ The additional information bar, to show the additional service icons. These icons show

only if the additional service is available. The icons for the channel information are:

- the icon, to show that the All channels list is selected, not grouped, not sorted;

- the icon, to show that the Current SAT list is selected, not grouped, not sorted;

- the icon, to show that a favorite list is selected, not grouped, not sorted;

- the icon, to show that a list is selected, grouped and/or sorted.

EchoStar International Corporation Page 4 - 11

Section 4

Familiarization

3.3.2. THE PHOTO INFOBANNER

DVR-7000 HDD

The photo InfoBanner shows the information related to the actual image.

■ The photo information bar, to show the name of the photo;

■ The jog shuttle, to show the actual status of the photo viewer (previous, pause, play, next);

■ The progress information bar, to show the start time and duration indicator;

■ The i-button, to indicate that there is detailed information available;

■ The additional information bar, to show the additional service icons. The icons are:

- the icon, to show that the All Photo list is selected, not grouped, not sorted;

- the icon, to show that a favorite list is selected, not grouped, not sorted;

ONLY

- the icon, to show that a list is selected, grouped and/or sorted;

- the icon, to show that you can move the photo (only in scale mode).

■ The menu bar, to show the special functions. The special functions are:

- the button, to scale the photo;

- the button, to repeat the list in a random order;

- the button, to repeat all the photos from the selected (favorite) list;

- the button, to capture an image as a personal background.

3.3.3. CHANNEL INFORMATION

With the InfoBanner shown, you can press the i-key once or twice to access extended channel information, if available first you view the extended program information, secondly you can view the technical channel information (transponder, polarity, symbol rate and PIDs).

■ Frequency,

to show the frequency of the transponder;

■ Polarity,

To show the polarity of the transponder;

■ Symbol rate

to show the symbol rate of the transponder;

■ Video PID

To show the video package ID of the channel;

■ Audio PID

To show the audio package ID of the channel;

■ PCR PID

To show the Program Clock Reference package ID of the channel.

3.4. POP-UP MENUS

Some pop-up menus are used to show that the receiver is busy to execute a task. Other popup menus require interaction with the user, you have to confirm or deny a earlier given command to complete the task.

Page 4 - 12 EchoNAV 2.2

Familiarization

3.4.1. SAT LIST

This pop-up menu gives you the possibility to choose directly from the available satellites. You can call up the pop-up menu with the satellite key on the remote control unit.

4. THE INDEX MARKERS

4.1. INDEX MARKER SHOWS IN THE INFOBANNER

With the InfoBanner shown, you can see the set index marker(s), at the marked position, in the progress bar of the DVR recording. The index markers are shown as vertical lines.

Section 4

4

4.2. SKIP TO NEXT/PREVIOUS INDEX

For the DVR mode:

4.3. LAST PLAYED INDEX MARKER

The (previous) and the (next) key are available to jump from one index marker to another index marker.

For the MP3 and photo mode (DVR-7000 only):

The (previous) and the (next) key are available to jump from one song or photo to another song or photo within the selected list.

When you press the key during the playback of a recording, the DVR stops and automatically adds the so called ‘Last played’ index marker. This index marker indicates the location where you stopped to play back a recording (just like a video tape). There is only one ‘Last played’ index marker which shows in the DVR list.

EchoStar International Corporation Page 4 - 13

Section 4

Familiarization

5. THE TIMERS

5.1. DVR STOP TIMER

This pop-up menu gives you the possibility to choose directly a stop time for the recording. You can call up the pop-up menu with the record key (press twice) on the remote control unit after a recording is started.

■ Set stop time

If available from the EPG, the program end time is shown;

■ Duration

You can define a period for which the timer continues to record.

Page 4 - 14 EchoNAV 2.2

OPERATION

1. TO NAVIGATE THROUGH THE MENUS

NOTE

Unless otherwise specified; this note explains the way you can navigate through the pages of the EchoNAV user menu.

1. Use the OK key to pull down the menu selection fields.

2. Use the  keys to scroll the selectable items.

3. Use the  keys to navigate between the left and right column of selectable items.

4. Use the EXIT key to leave the menu and return to the view mode.

5. In a pull-down menu:

- use the OK key to confirm the selection.

- the yellow bar indicates the active selection;

- on the left, the green page indicator indicates where you are.

1.1. TO GROUP A LIST

1. On the RCU, press the OK key.

2. Select the required mode.

3. On the RCU press the YELLOW key.

4. Read the available help text for information.

5. Select the required group option.

Operation

Section 5

NOTE

The selection for Group (yellow key) and Sort (blue key) are kept until you change the selection. The selection is made visible in the InfoBanner with icons. Sometimes a list seems to be empty because of the settings of the Group and Sort option. If this happens, select Group - None and Sort - None.

5

1.2. TO SORT A LIST

1. On the RCU, press the OK key.

2. Select the required mode.

3. On the RCU press the BLUE key.

4. Read the available help text for information.

5. Select the required sort option. Note that only for the Character and Word option a keyboard appears.

EchoStar International Corporation Page 5 - 1

Section 5

Operation

6. When the keyboard appears: a. use the arrow keys to navigate; b. press OK to accept the character; c. select the button to get lower case

characters and numbers;

d. select the button e. on the RCU, press the OK key to confirm.

NOTE

The selection for Group (yellow key) and Sort (blue key) are kept until you change the selection. The selection is made visible in the InfoBanner with icons. Sometimes a list seems to be empty because of the settings of the Group and Sort option. If this happens, select Group - None and Sort - None.

1.3. TO EDIT A LIST

1. On the RCU, press the OK key.

2. Select the required list.

3. On the RCU press the WHITE key.

4. Read the available help text for information.

5. Select the required edit option.

NOTE

Some EDIT options are not always available. If an option is not presented, select Group - None and Sort - None.

1.3.1. TO MOVE A CHANNEL

1. In the Edit menu, select the Move option.

2. Read the available help text for information.

3. Go to the channel you want to move.

4. On the RCU, press the OK key. Note a red bullet appears behind the selection.

5. If you want to undo the selection, press the OK key again.

Page 5 - 2 EchoNAV 2.2

6. Move the channel, either: a. use the keys; b. use the page + / - keys; c. use the numerical keys.

7. On the RCU, press the OK key to confirm.

8. Either: a. press the WHITE key to end the session, or; b. select the next channel you want to move, or;

c. press the key to return to the previous

location in the list.

9. When the pop-up appears, either: a. select Yes to save the changes, or: b. select No to undo the changes.

Operation

Section 5

1.3.2. TO LOCK A CHANNEL

CAUTION

You can only lock a channel if you have set the parental lock and the PIN-code correctly. We recommend, in the parental lock menu, that you check if the lock

option is set correctly.

5

NOTE

1. In the Edit menu, select the LOCK option.

2. Read the available help text for information.

3. Go to the channel you want to lock.

4. On the RCU, press the OK key.

5. If you want to undo the selection, press the

After you have set a lock onto a channel, the installation and the EDIT menu are automatically locked with an installation lock to prevent unauthorized access. Now you can only access these functions if you know the correct PIN-code.

Note a red bullet appears behind the selection.

OK key again.

EchoStar International Corporation Page 5 - 3

Section 5

Operation

6. Either: a. press the WHITE key to confirm the lock and

end the session, or

b. select the next channel you want to lock.

7. When the pop-up appears, either: a. select Yes to save the changes, or: b. select No to undo the changes.

8. You can temporarily unlock all channels: a. On the RCU, press the MENU key; b. Select the Parental Lock menu; c. Enter the correct PIN-code as requested; d. Set the channel lock to Off.

9. You can restore all the locks on the channels: a. On the RCU, press the MENU key; b. Select the Parental Lock menu; c. Enter the correct PIN-code as requested; d. Set the channel lock to On.

1.3.3. TO DELETE A CHANNEL

1. In the Edit menu, select the DELETE option.

2. Read the available help text for information.

3. Go to the channel you want to delete.

4. On the RCU, press the OK key. Note a red bullet appears behind the selection and the cursor advances to the next channel.

5. If you want to undo the selection, press the OK key again.

Page 5 - 4 EchoNAV 2.2

6. Either: a. press the WHITE key to confirm the deletion

and end the session, or

b. select the next channel you want to delete.

7. When the pop-up appears, either: a. select Yes to save the changes, or: b. select No to undo the changes.

Operation

Section 5

2. USE THE FAVORITE LISTS

Navigation and use of the favorite lists are the same as for the all channels and current satellite list as described before. The main difference is that you can setup and organize the favorite lists as required. EchoStar has already pre-named the favorite lists to help you getting started. It is however possible to change the name of the favorite list to something that is meaningful to you.

For adding channels quickly, you can use the group and sort option first to limit the amount of channels where you want to choose from. As an example, now it is possible to add all sport related channels in one step to the Sports TV favorite list.

Note that for each mode, a separate number of favorite lists is available.

5

2.1. USE THE INFOBANNER RELATED FUNCTIONS

2.1.1. DETAILED PROGRAM INFORMATION

1. On the RCU, press the i-key to get the InfoBanner.

2. If available, allow the receiver to collect the EPG information for the selected channel.

3. If the i-button in the InfoBanner is shown, use the i-key on the RCU to shift between the detailed program information and the InfoBanner.

4. On the RCU, press the EXIT key to remove the InfoBanner from the screen (only in TV-mode).

EchoStar International Corporation Page 5 - 5

Section 5

Operation

2.1.2. DETAILED CHANNEL INFORMATION

1. On the RCU, press the i-key to get the InfoBanner.

2. If the i-button in the InfoBanner is shown, press the i-key two times to get the detailed channel information.

3. If the i-button is not shown, press the i-key one time to get the detailed channel information.

4. On the RCU, press the i-key to remove the information from the screen.

3. TO SELECT ANOTHER SATELLITE

1. On the RCU, press the key.

2. In the Satellites List pop-up menu, select the required satellite.

3. On the RCU, press the OK key. Note that the dish moves towards the selected satellite.

4. TO USE THE INDEX MARKERS

4.1. SET THE INDEX MARKER

1. Play back a recording.

2. On the RCU: a. press the i-key to show the InfoBanner; b. press the MENU key to activate the menu;

c. use thekeys to select the button.

3. Wait for the scene that you want to mark.

4. On the RCU, press the OK key.

5. Wait for the popup to disappear.

6. On the RCU: a. press the MENU key to leave the menu; b. press the EXIT key to remove the InfoBanner.

Page 5 - 6 EchoNAV 2.2

4.2. SET THE LAST PLAYED INDEX MARKER

1. Play back a recording.

2. On the RCU:

a. press the key to stop the playback of a

recording;

b. the receiver automatically adds the so called

‘Last played’ index marker.

c. in the list note that the ‘Last played’ index is

now applied to this event.

4.3. PLAY BACK AN INDEX MARKER

1. Select the DVR mode.

2. Select the event with the index marker (+).

3. On the RCU, press the i-key to expand (-).

4. Select the index that you want to play back.

5. On the RCU, press the OK key to playback the index.

Operation

Section 5

4.4. USE THE INDEX MARKER

FOR THE DVR MODE

1. After an index marker is set, on the RCU:

a. press the key to go to the previous index;

b. press the key to go to the next index.

FOR THE MP3 MODE (DVR-7000 HDD ONLY)

2. After an index marker is set, on the RCU:

a. press the key to go to the previous song;

b. press the key to go to the next song.

5

EchoStar International Corporation Page 5 - 7

Section 5

Operation

5. TO USE THE PHOTO ALBUM

DVR-7000 HDD ONLY

NOTE

The use of the photo album is similar to the use of the MP3 player. You can select a photo from a list and ‘play’ the photo to view it. If you press play key, the list starts to behave as a ‘slide show’, all photos in the list will be shown with a selectable time interval.

5.1. PLAY BACK A PHOTO

1. On the RCU, press the OK key.

2. Select the PHOTOS mode.

3. Read the available help text for information.

4. Select a photo, either: a. use the arrow keys; b. use the page + / - keys;

5. On the RCU, press the OK key to show (play back) the photo in full size.

6. On the RCU:

a. press the key for next photo;

b. press the key for previous photo; c. press the i-key twice for detailed information.

d. press the key to start a (photo) slide show;

e. press the key for pause;

f. press the key to stop and return to the list.

7. For the different play modes, on the RCU: a. press the MENU key to access the menu; b. press thekeys to select a play mode; c. press the OK key, to activate the selection; d. press the OK key, to cancel the selection; e. press the MENU key to leave the menu.

8. To capture a personal background, on the RCU: a. select the photo that you want to capture; b. press the i-key to show the InfoBanner; c. press the MENU key to activate the menu;

d. use thekeys to select the button.

9. On the RCU, press the OK key.

10. Wait for the popup to disappear.

11. On the RCU: a. press the MENU key to leave the menu; b. press the EXIT key to remove the InfoBanner.

Page 5 - 8 EchoNAV 2.2

Operation

Section 5

6. TO USE THE DVR STOP TIMER

NOTE

Be aware that the DVR stop timer overrides all earlier set timers. If a timer overlap occurs, you will loose your earlier defined timer. View the timer list through the EPG menu, press green, select timers.

1. On the RCU:

a. press the key twice to start the recording;

b. .press the key twice to show the timer;

2. In the Timer pop-up menu; a. If available from the EPG,

- select the Set stop time for program end;

- on the RCU, press the OK key to confirm, or:

b. If time is not available from the EPG;

- Select Set stop time - - : - -

- on the RCU, press the OK key;

- use the numerical keys to enter a time;

- press the OK key to confirm. or:

c. Select a pre-set time after which the recording

stops, or:

d. Define a personal set time after which the

recording stops:

- Select Duration - - : - -

- on the RCU, press the OK key;

- use the numerical keys to enter a time;

- press the OK key to confirm.

5

EchoStar International Corporation Page 5 - 9

Section 5

Operation

Page 5 - 10 EchoNAV 2.2

Maintenance

MAINTENANCE

Section 6

1. USER LNB SETTING - SUB-MENU (ADVANCED ONLY)

1. On the RCU, press: a. the MENU key;

b. the  key to select the menu;

c. the OK key, to select the menu.

2. Press the OK key and make the selections.

3. Read the available help text for information.

4. Go to the Save settings field.

5. On the RCU: a. press the OK key to save the settings;

b. press the EXIT key to leave the menu.

2. SET LIMITS - SUB-MENU

CAUTION

On the motorized dish, set the physical East and West limit switches first. Failing to do so might cause damage to your motorized dish installation or other properties.

1. On the RCU, press: a. the MENU key;

b. the  key to select the menu;

c. the OK key, to select the menu.

2. Read the available help text for information.

3. On the RCU: a. press thekey to set the EL (East limit); b. at the motor error, press thekey once; c. press the OK key.

4. On the RCU: a. press thekey to set the WL (West limit); b. at the motor error, press thekey once; c. press the OK key.

5. If required, go to the Program satellites field.

6. On the RCU: a. press the MENU key to save the settings;

b. press the EXIT key to leave the menu.

6

EchoStar International Corporation Page 6 - 1

Section 6

Maintenance

3. SEARCH CHANNELS - ANALOG IF

1. On the RCU, press: a. the MENU key;

b. the  key to select the menu;

c. the OK key, to select the menu.

2. Select for the Search Mode: Analog IF

3. Go to the Search channels field.

4. On the RCU, press the OK key.

5. Select Horizontal or Vertical polarity.

6. For one LNB, go to the Start field.

7. For more LNBs, select the applicable band.

8. Press the OK key

9. Wait for the search to complete: a. the receiver display shows a moving dot; b. the search completed popup menu appears.

10. On the RCU: a. press the OK key to save the settings; b. press the EXIT key to leave the menu.

4. ADD DATA (SAT/TP) - SUB-MENU

FOR DISEQC1.2 CONFIGURATIONS

1. On the RCU, press: a. the MENU key;

b. the  key to select the menu;

c. the OK key, to select the menu.

2. In the SAT field: a. Press the OK key to drop-down the menu;

b. Select satellite S00; c. Press the OK key.

3. Note that the Add data menu appears. In this menu you can create a new satellite and it’s transponders.

4. Continue with step 5.

Page 6 - 2 EchoNAV 2.2

Maintenance

Section 6

FOR FIXED CONFIGURATIONS

1. On the RCU, press: a. the MENU key;

b. the  key to select the menu;

c. the OK key, to select the menu.

2. In the SAT field: a. Press the OK key to drop-down the menu;

b. Select satellite S00; c. Press the OK key.

3. Note that the Add data menu appears. In this menu you can create a new satellite and it’s transponders.

4. Continue with step 5.

FOR ALL CONFIGURATIONS

5. In the SAT field: a. Press the OK key to drop-down the menu;

b. Select satellite S00; c. Press the OK key.

6. Note that the keyboard comes in view.

7. Use the on-screen keyboard to enter the name of the satellite:

a. use the arrow keys to navigate; b. press OK to accept the character; c. select the button to get lower case

characters and numbers; d. select the button e. on the RCU, press the OK key to confirm.

8. On the RCU, use the numeric keys to enter the Degrees (position).

9. Select the Location:

6

NOTE

It is possible to add more than one TP to the new satellite. In that case, in the following procedure select Add more (to add a new TP) in the step where you are asked to go to the Continue field (to search channels).

FOR ANALOG/DIGITAL RECEIVERS

10. In the Frequency field: a. On the RCU, use the numeric keys to enter the

transponder frequency; b. Press the  key to advance to the next field; c. Select Digital or Analog.

11. In the Polarity field, select H for Horizontal or V for Vertical.

12. In the Symbol rate field, enter with the numeric keys the symbol rate.

EchoStar International Corporation Page 6 - 3

Section 6

FOR DIGITAL RECEIVERS

7. In the Frequency field, on the RCU, use the

8. In the Polarity field, select H for Horizontal or V for

9. In the Symbol rate field, enter with the numeric

FOR ALL RECEIVERS

10. Leave the value Auto for Video PID, Audio PID and

11. Go to the Continue field.

12. On the RCU, press the OK key to advance.

13. If the dish is not aimed at the satellite, the search

Maintenance

numeric keys to enter the transponder frequency;

Vertic al.

keys the symbol rate.

PCR PID.

cannot be completed. When the popup message ‘No channels found’ shows, press OK and continue with step 14..

FOR DISEQC1.2 CONFIGURATIONS

14. On the RCU: a. press the MENU key;

b. thekey to select the menu;

c. the OK key, to select the menu.

15. Select for the Search Mode: Update.

16. When in the Position field: a. press and hold theor key and watch the

signal indicator for an indication;

b. in the signal indicator, make sure a network

name is shown;

c. press thekey to select another transponder

for signal verification; d. press thekey to select the Position field; e. use thekey to fine tune for the best signal

level and quality; f. press the OK key, note that the saved position

of the satellite is shown.

17. Go to the Search channels field.

18. On the RCU, press the OK key to advance.

Page 6 - 4 EchoNAV 2.2

Maintenance

19. Wait for the search to complete: a. the receiver display shows a moving dot; b. the Search completed popup menu appears.

20. On the RCU, press the OK key.

Section 6

FOR FIXED CONFIGURATIONS

14. On the RCU: a. press the MENU key;

b. thekey to select the menu;

c. the OK key, to select the menu.

15. In the SAT field: a. Press the OK key to drop-down the menu;

b. Select satellite your new satellite; c. Press the OK key.

16. Go to the Check signal field.

17. On the RCU, press the OK key to advance.

18. Wait for the Checking configuration to complete.

19. Read the available help text for information.

20. Make the required selections.

21. If the red dot in the TP field stays: a. select another transponder; b. go to the Check signal field; c. on the RCU, press the OK key.

22. Wait for the search to complete: a. the receiver display shows a moving dot; b. the Search completed popup menu appears.

23. On the RCU, press the OK key.

EchoStar International Corporation Page 6 - 5

6

Section 6

Maintenance

Page 6 - 6 EchoNAV 2.2

Troubleshooting

TROUBLESHOOTING

Section 7

1. TO SOLVE AN INSTALLATION RELATED PROBLEM

Problem Possible cause What to do?

1. I cannot add a SAT.

2. The positioner does not respond when I want to go to the new satellite.

3. I cannot add a TP.

4. I cannot configure User LNBs.

5. I cannot access the User LNBs during setup.

6. During Add data, no channels are found during Search channels.

■ In a SAT field, you did not

select S00.

■ You did not save the

position of the satellite.

■ In a TP field, you did not

select TP00.

■ You did select the Easy

mode. In this mode only 4 LNBs are supported.

■ In the Program satellites

menu, in the User LNB field, you did not press the i-key.

■ The dish is not aimed at

the satellite.

■ Refer to section 6,

chapter Add data.

■ Go to the Program

satellites menu and save the (correct) position.

■ Refer to section 6,

chapter Add data.

■ Select the Advanced

mode, refer to section 6, chapter Add data.

■ Select the User LNB field

and on the RCU, press the I-key to advance to the User LNB setting.

■ Go to the Program

satellites menu and save the (correct) position.

7

EchoStar International Corporation Page 7 - 1

Section 7

Troubleshooting

Page 7 - 2 EchoNAV 2.2

GLOSSARY

1. LIST OF USED ABBREVIATIONS

Glossary

Section 8

S00

SR

TP00

Satellite menu where you can change S00 into a new satellite.

S00 brings you to the Add data

Symbol Rate

Transponder data menu where you can change TP00 into a new transponder.

TP00 brings you to the Add

8

EchoStar International Corporation Page 8 - 1

Section 8

Glossary

2. EXPLANATION OF USED TERMINOLOGY

Add data This menu gives the possibility to add a user defined

satellites and transponders.

Advanced mode This is an installation mode where the user has full flexibility

to setup an installation with multiple (user defined) LNBs.

Easy mode This is the recommended installation mode. This mode offers

a guided initial setup in which the user is assisted by the sequence of the menus and editable pre-settings.

Edit data This menu gives the possibility to change the name of the

satellite and the transponder setting.

Page 8 - 2 EchoNAV 2.2

Index

Section 9

INDEX

A

add sat ..................................................3-1, 6-2

add tp

...................................................3-2, 6-2

analog if autosat

....................................................... 6-2

..................................................3-3, 4-5

B

backgrounds ................................................ 4-3

blue key

....................................................... 5-1

C

capture background ............................4-12, 5-8

check signal conditional access menu

................................................. 4-7

............................. 4-3

D

delete a channel .......................................... 5-4

detailed program information disecq 1.2 setup

.......................................... 3-2

.......................5-5

E

edit a list ...................................................... 5-2

F

favorite lists ................................................. 5-5

features fixed dish setup fixed installations

....................................................... 4-1

........................................... 4-7

......................................... 3-1

G

group a list ................................................... 5-1

H

hard disk .................................................... 4-10

I

i-button .............................................4-11, 4-12

index marker indicator infobanner installation setup menu

................................................ 5-6

....................................................... 4-9

..........................................4-11, 5-5

................................ 4-3

K

keyboard ...................................................... 5-2

L

last played index .......................................... 5-7

list

................................................................ 5-2

local time page lock a channel

............................................ 4-4

............................................. 5-3

O

ota ................................................................4-9

P

photo album .................................................5-8

polarotor previous index previous song program satellites

.......................................................4-8

..............................................5-7

................................ 4-6, 4-7

Q

quattro ..........................................................4-2

R

red bullet ......................................................5-4

remote control unit repeat list repeat randomly

...................................................4-12

.......................................4-2

.........................................4-12

S

s00 ........................................3-1, 6-2, 6-3, 7-1

satellites list scale

..........................................................4-12

search channels page setup after memory erase signal signal indicator smatv sort a list system setup menu

.................................................5-6

........... 3-2, 3-3, 3-6, 6-2

............................3-1

................................................... 4-7, 4-9

.............................................4-9

...........................................................3-7

......................................................5-1

......................................4-5

T

tp00 ...............................................3-1, 6-3, 7-1

U

use the infobanner .......................................5-5

user lnb user lnb settings user preferences menu user profile page

........................................................7-1

...........................................6-1

................................4-3

..........................................4-3

W

white key ......................................................5-2

Y

yellow key ....................................................5-1

M

memory erase ........................................... 4-10

move a channel moveable dish

........................................... 5-2

............................................. 3-2

N

navigation .................................................... 5-1

next index next song

EchoStar International Corporation Page 9 - 1

....................................................5-7

..................................................... 5-7

9

Section 9

Index

Page 9 - 2 EchoNAV 2.2

LNB(F) Configuration matrix

APPENDIX 1

1. LNB CONFIGURATION MATRIX

In the installation menu, the different LNBs are already pre-programmed to save you a lot of configuring routines.

LNB TYPE LO Frequency LO Selection 13/18V 0/22kHz

Appendix 1

H V H V

Standard

Enhanced

Quattro

10,000 disabled 18 18 0 0

9,750 disabled 18 18 0 0

9,750 13V 13 13 0 0

10,750 18V 18 18 0 0

C-Band

DBS

10.7 LNB

5,150 disabled 18 18 0 0

10,750 disabled 18 18 0 0

10,700 disabled 18 18 0 0

2. LNBF CONFIGURATION MATRIX

In the installation menu, the different LNBFs are already pre-programmed to save you a lot of configuring routines.

LNBF TYPE LO Frequency LO Selection 13/18V 0/22kHz

Standard

Enhanced

Universal

10,000 disabled 18 13 0 0

9,750 disabled 18 13 0 0

9,750 0 kHz 18 13 0 0

10,600 22 kHz 18 13 22 22

A1

HVHV

Quattro

9,750 0 kHz 18 13 0 0

10,750 22 kHz 18 13 22 22

C-Band

C-Band SS

5,150 disabled 18 13 0 0

5,150 13V 18 13 0 0

5,750 18V 18 13 0 0

10.7 LNBF

10,700 disabled 18 13 0 0

EchoStar International Corporation Page A1 - 1

Appendix 1

LNB(F) Configuration matrix

3. USER DEFINED LNB(F) MATRIX

In the User LNB setting menu, you can define your own LNB(F). You can use the list below to note the settings.

User LNB(F) LO Frequency LO Selection 13/18V 0/22kHz

HVHV

User ........ 1

User ........ 2

User ........ 3

User ........ 4

User ........ 5

User ........ 6

User ........ 7

User ........ 8

User ........ 9

User ........ 10

... ...,... ... ... ... ...,... ... ... ... ... ... ... ... ... ... ...

User ........ 11

User ........12

User ........ 13

User ........ 14

User ........ 15

User ........ 16

Page A1 - 2 EchoNAV 2.2

... ...,... ... ... ... ...,... ... ... ... ... ... ... ... ... ... ...

EchoStar DVR-5000 HDD Viaccess, DVR-7000 HDD Supplementary Manual

Specifications and Main Features

Frequently Asked Questions

User Manual