Echo MS-40BP User Manual

Page 1
Backpack
Use and Care Manual
Model MS-40BP
4.0G/15.1L
WARNING!
Carefully Read These Instructions Before Use
011289 R0211
Page 2
WARNING!
IMPROPER USE OR FAILURE TO FOLLOW INSTRUCTIONS CAN RESULT IN PRODUCT FAILURE OR INJURIES. FOR SAFE USE OF THIS PRODUCT YOU MUST READ AND FOLLOW ALL INSTRUCTIONS BEFORE USING.
WARNING: Handling the brass parts of this product will expose you to lead, a chemical known to the State of California to cause birth defects and other reproductive harm.
Wash hands after handling.
CAUTION
RULES FOR SAFE OPERATION
Before assembling and operating your sprayer, read all instructions thoroughly. When working with equipment under pressure, safety precautions must always be carefully observed, including the following:
NEVER spray flammable materials or pressure and gas producing
chemicals.
ALWAYS read chemical label before filling sprayer as some chemicals may
be hazardous when used with this sprayer.
ALWAYS wear goggles, gloves, a long-sleeve shirt, long pants, and full foot
protection when spraying. Work in a ventilated area or outdoors.
PRE-USE CHECK: Before each use check tightness of hose nut to be sure hose is
securely attached to the shut-off assembly. Insure hose is securely attached to the tank by tightening hose clamp if necessary. Insure that all nozzle and wand connections are tight. Insure the large pump clamp is tight. Insure the 2 bolts used to attach the pump lever to the pump shaft are tight.
DO NOT leave a pressurized sprayer in the hot sun or anywhere near a heat source.
Heat can produce pressure to build up causing sprayer to ignite or explode resulting in injury or death.
NEVER pressurize sprayer by any means other than the original pump. Over
pressurizing can cause sprayer to explode resulting in injury or death.
DO NOT attempt to modify or repair this product except with original manufacturer’s
parts.
NOTE: The tank and hose may have residual water in it due to quality testing performed on the sprayer.
Page 3
APPLICATIONS & USE FOR YOUR SPRAYER
Avoid using a sprayer for general cleaning purposes if plant protection or herbicide chemicals have already been used in the sprayer. If a sprayer has been used for plant protection or as an herbicide, clean the sprayer completely (see cleaning section) before using.
Plant Food
: Use different spray patterns for optimum foliage feeding or for fungicide and
pesticide application. Herbicides: Reduce weeds and unwanted plants but avoid using the same sprayer for plant feeding or protection without thoroughly cleaning (see cleaning section) the sprayer first. General Household Use: Apply detergents, vinegar, cleaning solutions, warm water (do not exceed 120°F/49°C) or nontoxic household cleaning chemicals for carpets, floors, walls, glass, counter tops and ceilings. DO NOT use sprayer that has been used with herbicides, pesticides or other toxic chemicals for household applications. General Outdoor Use: Use the sprayer for cleaning windows or with a detergent for general purpose cleaning. Other applications include wood preservatives, waxes, water proofing, and diluted household bleach (max. 1 part household bleach to 9 parts water solution).
SPRAYER COMPONENTS & USE INFORMATION
NOZZLE ASSEMBLY
Figure 1-2
Unscrew the nozzle cap (1) from the nozzle body (3) with retaining nut (2) fastened tightly to the elbow (5). Unscrew the retaining nut (2). Push the nozzle body (3) with the nozzle gasket
(4) out of the retaining nut (2). To reinstall the nozzle, reverse the above instructions.
Figure 3
Unscrew the retaining nut from the elbow and push the fan nozzle tip and gasket out of the retaining nut. To reinstall the nozzle, reverse the above instructions.
1. P
oly
Nozzle Ca
p
2. Retaining Nut
3. Nozzle Body
1. Brass Nozzle Cap
2. Retaining Nut
3. Nozzle Body
Retaining Nut
Fan Nozzle Tip
4. Nozzle Gasket
5. Elbow
4. Nozzle Gasket
5. Elbow
Figure 1 Figure 2 Figure 3
WAND ASSEMBLY
1. Make sure the o-ring is installed on the end of the wand. Insert the wand into shut-of f valve.
2. Turn and tighten the retaining nut clock-wise onto the shut-off valve.
Wand
Retaining Nut
O-ring
Shut-off
Valve
Nozzle Gasket
Elbow
Page 4
SPRAYER COMPONENTS & USE INFORMATION, Continued
INSTALLING THE PUMP HANDLE
The pump handle can be mounted on either side of the pump shaft (A). To install the pump handle
place the handle (C) over the shaft (A) aligning the pump handle hole and shaft hole. Push the straight side of the cotter pin (B) through the aligned hole as shown in figure 1 thru 3. There are holes in the pump handle to allow for either left(fig.4) or right (fig.5) hand mounting.
C
A
B
Figure 1
Cotter Pin
Figure 4
Left Hand
Figure 2
Line up holes
Figure 5
Right Hand
STOWAWAY PUMP HANDLE
Pull up
INSTALLING THE SHOULDER STRAP
The top of the shoulder straps are attached to the tank.
Attach the lower end of the straps by clipping the strap hooks to the metal frame between where the frame exits the tank and curves around.
NOTE: If your straps become contaminated with dirt or chemicals, wash with mild soap and water and let dry overnight. If this does not remove the contamination, replace with new straps.
Rotate 180º
Figure 3
Slide pin through holes.
Pump Handle Positioned For Use (right hand shown)
Set into slot
WAND CLIP
The wand can be attached to the pump handle using the wand clip.
Page 5
SPRAYER COMPONENTS & USE INFORMATION, Continued
4 STAGE FILTERING SYSTEM
This backpack sprayer is equipped with a 4 stage filtering system (see figure 1). Stage 1 is a filter basket incorporated into the tank opening where fluid is added. Stage 2 and 3 filters are located at the inlet of the pressure cylinder. Stage 2 is a removable In-Tank filter. Stage 3 is a removable filter cartridge integrated into the pressure cylinder. Stage 4 is a removable filter incorporated into the shut-off assembly. Periodic cleaning of these filters is recommended to insure consistent fluid flow through the sprayer. This will also reduce sprayer component wear.
Stage 3 filter cartridge cleaning requires removal of the entire pressure cylinder assembly (see section “disassembling and repairing the pressure cylinder”). Once the pressure cylinder is removed the stage 3 filter can be removed for cleaning (see figure 3). Periodic cleaning of the stage 2 filter is highly recommended and will reduce the need to perform this disassembly. It is best to have no or minimal fluid in the tank before removing and reinstalling the stage 2 In-Tank filter. The In-Tank filter needs to be oriented in a specific way when inserted into the pressure cylinder base (see figure 2).
The stage 4 filter is a removable filter incorporated into the inlet side of the shut-off valve (see section “disassembling and repairing the shut-off valve”) . Make sure pressure is released before detaching the hose from the shut-off. It is best to have no or minimal fluid in the pressure cylinder before removing and reinstalling the stage 4 shut-off filter as fluid can leak from the hose.
Figure 1
Stage 2 (removable In-Tank filter)
Stage 1
(filter
basket)
Pressure
Cylinder
Stage 3 (removable
filter cartridge)
Stage 4 (Removable Shut-off filter)
Figure 2 Stage 2 (removable In-Tank filter)
Guide edge facing away from pressure cylinder
Guide edge on pressure cylinder
Figure 3 Stage 3 (removable filter cartridge)
pressure cylinder base
Filter cartridge removedFilter cartridge in
FILLING THE SPRAYER
Make sure the filter basket is in place to keep debris from entering the tank. Determine the amount of mixture needed for your application. Add the proper amount of water to the
tank. Add the proper amount of chemical to the tank (check the chemical label for proper ratio of chemical). Stir mixture in tank with a clean utensil (like a paint stirrer). The tank will hold the 4-gallon (15.1L) capacity plus the chemical.
It is not necessary to completely fill the sprayer tank with each use. You can fill the tank with only the amount needed for each application.
Always follow the manufacturer’s instructions included on their product label.
Page 6
SPRAYER COMPONENTS & USE INFORMATION, Continued
HELPFUL SPRAYING INFORMATION
Use RAPID pump strokes to prime the pump.
You will know the pressure chamber is filling with liquid when you feel firm resistance from the pump. The air in the pressure chamber is compressed from repeated strokes. By pressing the hand lever on the shut-off, the valve opens. For safety lock-off feature (no-spraying), pull up on handle and move red locking mechanism into lock-off position as shown in fig.
1. To disengage, push down on handle and return red locking mechanism to neutral position as in fig. 3. For lock-on feature (continuous spraying), push down on handle and move red locking mechanism into lock-on position as shown in fig. 2. To disengage, push down on handle and return red locking mechanism to neutral position as shown in fig. 3.
If the shut-off fails, place wand into tank until pressure is completely exhausted.
LOCK-OFF POSITION LOCK-ON POSITION NEUTRAL POSITION
Locking Mechanism
Handle
Up
Handle Down
Figure 1 Figure 2 Figure 3
For easy pump action use the END of the pump handle. The amount of liquid delivered during spraying depends on the rate of pump stroke. The fan nozzle tip is rated at .4 gpm at 40psi. This is the nominal operating pressure of the sprayer.
If you experience a rapid drop in pressure, drain the sprayer completely and pump the handle
Note:
with an empty tank. The pressure chamber will fill with the required volume of air to repressurize. Perform this procedure from time to time as routine maintenance.
POWDER-BASED CHEMICALS
-based chemicals (powder mixed with liquids to make the spraying agent) are usually abrasive
Powder and can cause wear. When you use a powder-based chemical in your sprayer, make sure it is thoroughly dissolved in the liquid solution. Thoroughly clean and flush the sprayer with water to extend the life of the sprayers parts.
CLEANING
1) Always empty the sprayer and clean the tank thoroughly after each use.
2) Pump the sprayer handle until all of the contents and air exit through the nozzle (minimum of 30 strokes).
3) Fill tank half way with water and pump the water out as explained in step 2 (repeat several times as necessary).
Other Cleaning Hints:
• Improper spray distribution usually means the nozzle is clogged, remove the nozzle and clean it.
• Soap can be added to the water to clean the tank.
• Do not use strong cleaning agents or abrasives.
• If you use a chemical agent to clean the tank follow the manufacturer’s recommendations for the disposal of the waste water.
• Follow the chemical manufacturers instructions for clean up.
Page 7
STORING / MAINTAINING YOUR SPRAYER
• The sprayer should be stored out of direct sunlight in a cool dry space.
• Before freezing weather make sure to drain all liquid in the tank
, pump, pressure cylinder, hose, shut-off valve, wand and nozzle, to avoid liquid expansion and cracking in the sprayer components (See “Cleaning” section). Lock the shut-off valve in the “open” position.
• When service is required call your nearest dealer and always insist on original manufactured replacement parts.
• Inspect the hose, wand, pump, tank and shut-off valve for wear, damage or leaks on a regular basis and repair defects promptly.
TROUBLE SHOOTING YOUR SPRAYER Symptom
Possible Reason Correction
Difficulty actuating the pump handle and/or Upper valve plate sticks Clean or replace valve pla pump handle moves itself back up. Piston cylinder outlet passage clogged Clean piston cylinder outlet passage
Little or no resistance during Damaged/worn/dirty/upper valve plate Clean or Replace Valve Plate repeated pumping – no pressure. Damaged /worn upper o-ring on piston cylinder Replace O-ring
Piston Collar or piston cylinder Replace Collar or Piston cylinder assembly assembly is worn
Too much resistance after just a few Not enough air cushion in the pressure Release pressure in pressure chamber pumping strokes but pressure only lasts chamber Remove the hose & drain pressure briefly. chamber. Reconnect the hose.
Upper valve plate damaged/worn/dirty Clean or replace upper valve plate
Upward pumping action is more difficult Vent hole is clogged Clear the vent hole in cap and/orpump handle moves itself backdown. Lower valve plate sticks Clean or replace the valve plate
Clogged intake filter Clean the In-Tank filter and or removable
cartridge filter
Piston cylinder intake clogged Clean piston cylinder intake
Leaks at Piston Cylinder Damaged/worn/Dirty Collar Clean or Replace Piston Collar
Damaged Piston Cylinder Replace Piston Cylinder Damaged Piston Replace Piston
Shut-off leaks Connections loose Tighten connection
Worn or damaged shut-off Rebuild or replace the shut-off valve
Wand assembly leaks Connections loose Tighten connection
Damaged or worn o-ring/gasket Replace o-ring/gasket
Nozzle assembly leaks Connections loose Tighten connection
Damaged or worn o-ring/gasket Replace o-ring/gasket
Leak between pump assembly Pump clamp loose Tighten clamp and tank O-ring worn or damaged Replace pressure chamber oring
te
Hose leaking at tank outlet Hose clamp loose Tighten clamp
Hose leaking at shut-off Connection loose Tighten retaining nut
Damaged or worn o-ring/gasket Replace o-ring/gasket
Page 8
DISASSEMBLING AND REPAIRING THE PISTON PUMP
Collar
A
Figure 1
Figure 2
Figure 3
C B
lay the unit on its back (Fi sprayer hose. Caution: There could be residual liquid in the hose and pressure cylinder. Remove the nut and bolt from the protective cap and remove the cap
g
ure 1). Loosen the hose clamp and remove the
(ref: figure 9). Rotate the pump shaft in order to reach two lever bolts (A). Using an allen wrench, remove the lever bolts. Pull the piston assembly (B) out of the piston cylinder (C).
2) Remove the piston cylinder assembly by turning the piston cylinder
1) Remove the cotter pin and pump handle. With the pump facing towards you,
-clockwise when viewing the sprayer from the bottom. Caution: The
counter piston cylinder may have sharp edges.
3) Check for vertical scratches on the inside of the piston n
der and the piston. If one or both are scratched, replace
cyli them.
4) To replace the collar, push it off of the crown of the piston
with your thumb. You will see form fitted slots
to install the new collar on to the piston crown.
Intake
Upper Valve plate
Lower Valve plate
Piston cylinder tab
Figure 4
Piston Cylinder
Figure 5
Figure 6
Outlet Passa
ge
Pressure cylinder base rib
5) There are 2 valve plates on the piston cylinder, one on the inside of the cylinder and one on the outside top. The valve plates are held in place with a screw and washer and can be removed and replaced using a Phillipshead screw driver. The 2 o-rings can be removed and replaced as well. Insure that the o-rings are positioned in the o-ring grooves in the piston cylinder.
6) Grease the 2 O-rings on the piston cylinder (do not get any grease on the
valve plate) and screw the Screw the piston
piston assembly into the pressure cylinder base.
cylinder clockwise until tight and the bottom O-ring is no longer visible. When properly placed, the tab on the piston cylinder will line up with the rib on the pressure cylinder base.
Page 9
7) Apply Petroleum jelly to the inside of the piston cylinder wall and on the collar cylinder.
, and reinstall the piston assembly into the piston
Figure 7
8) Insert the piston at an angle with the leading edge of the collar placed over the slot in the piston cylinder. Bolt the piston assembly to the pump shaft using the lever bolts.
Figure 8
Protective Dust Ca
p
9) Replace the protective dust cap. Tighten the nut and bolt. Reinstall the pump handle. Replace the hose and firmly secure
the hose clamp in place.
Figure 9
DISASSEMBLING AND REPAIRING THE PUMP ASSEMBLY
Only remove the pump assembly if the cartridge filter is clogged or the sprayer is leaking between the p
1. Release the pressure from the sprayer and remove all liquid from both the pressure chamber and tank.
2. Remove hose.
3. Remove the In-tank filter from the pressure cylinder (located inside the tank - fig. 1).
4. Remove 2 bolts attaching the pivot lever to the pump shaft and remove piston assembly (fig. 2a & 2b).
5. Remove the large clamp holding the pressure chamber and tank together (fig 1).
6. Rock the pressure chamber back and forth and push down to free it from the tank (fig 1).
7. Once freed the entire pump assembly can be removed by maneuvering it through the base frame (fig 3a & 3b).
essure chamber o-ring and tank.
r
In-tank Filter
B
Figure 1
Clamp
Figure 2a
Figure 2b
Pressure Chamber o-ring
Figure 3a
Pump Assembly
Figure 3b
Page 10
8. At this point the filter cartridge in the pressure chamber base can be removed with pliers and cleaned (fig 4).
9. The pressure chamber o-ring can also be replaced. DO NOT stretch the
Figure 4
o-ring over the bottom flange. Assemble the o-ring over the top of the chamber. Apply petroleum jelly to the o-ring before reinstalling pump asembly into the tank (fig. 3b).
10. Reassemble backwards from step 7 thru 2, performing each step in
Tank tab
Figure 5
reverse. Note: there is a notch/tab combination in the pump assembly/tank to be used for alignment (fig. 5).
Pump Assembly Notch
DISASSEMBLING AND REPAIRING THE SHUT OFF VALVE
1) Assembled shut-off valve (Figure 1).
Figure 1
A
Figure 2
Figure 3
Valve Stem
C
2) Remove the retaining pin (A) (Figure 2) place the notched end of the retaining pin on a hard surface and push down. Remove the retaining pin and slide the handle o
f the valve
f
stem.
3) Remove the retaining nut (o-ring attached), spring, and valve stem (B) (Figure 3). Replace worn parts. Lubricate the O-rings and reassemble by reversing the steps above. Place the
handle groove
in the slotted area of the valve stem and make sure the locking clip
B
is positioned in the neutral position (see “Helpful Spraying Information” section). Insert the retaining pin. Push down on the handle a few times to distribute the lubricant evenly. Check filter (C) in end of shut-off valve for debris. Remove filter and flush with water to clean out.
Page 11
NOZZLE ASSEMBLY
REPLACEMENT PARTS ORDER INFORMATION
O-ring
99944100484 Flat Fan Nozzle
Screw
p
Ca
Hose Washer
99944100485 Nozzle Kit
99944100482 Brass Adjustable Nozzle
Wand
99944100481 Filter Replacement Kit
99944100483 Poly Adjustable Nozzle
99944100480 Wand Assembly
Retaining Nut
Hose
99944100477 Shut-off Valve Repair Kit
10E
99944100479 Hose Assembly
99944100478 Shut-off Assembly
Page 12
99944100474 Piston Cylinder Assembly
99944100475 Pump Piston Assembly
REPLACEMENT PARTS ORDER INFORMATION
Upper ValvePlate
Upper O-ring
Lower O-ring
Piston Collar
Valve Plate -
Piston Cylinder
99944100473 Filter Basket & Cap
99944100471 Piston Pump Repair Kit
Collar-
Pump Piston
O-ring­Piston Cylinder
O-ring-
Pressure Chamber
99944100486 O-ring Kit
Elbow O-ring Hose Gasket
Nozzle Gasket
Wand O-ring
ECHO, INCORPORATED 400 Oakwood Road, Lake Zurich, IL 60047 www.echo-usa.com
99944100472 Straps
99944100489 Pump Handle
99944100488 Wand Clips
Page 13
ECHO LIMITED WARRANTY STATEMENT FOR
SPRAYERS SOLD IN USA AND CANADA BEGINNING 01/01/2010
ECHO'S RESPONSIBILITY
ECHO Incorporated’s Limited Warranty, provides to the original end user purchaser that this ECHO product is free from defects in material and workmanship. Under normal use and maintenance from date of purchase, ECHO agrees to repair or replace at ECHO’s discretion, any defective product free of charge at any authorized ECHO servicing dealer within listed below application time periods, limitations and exclusions. THIS LIMITED WARRANTY IS ONLY APPLICABLE TO ECHO PRODUCTS
SOLD BY AUTHORIZED ECHO DEALERS. IT IS EXTENDED TO THE ORIGINAL END USER PURCHASER ONLY, AND IS NOT TRANSFERABLE TO SUBSEQUENT OWNERS.
warranted only for the balance of the original unit or accessory warranty period. Any damage caused by improper use, modifications, installation or maintenance is not covered by this warranty. All parts or products replaced under warranty become the property of ECHO, Inc. For a list of Authorized ECHO Dealers refer to WWW.ECHO-USA.COM or call 1-800-432-Echo.
OWNER’S RESPONSIBILITY
To ensure trouble free warranty coverage it is important that you register your Echo equipment on-line at WWW.ECHO­USA.COM or by filling out the warranty registration card supplied with your unit. Registering your product confirms your warranty coverage and provides a direct link if we find it necessary to contact you. The owner shall demonstrate reasonable care and use, and follow preventative maintenance and storage Instructions, as prescribed in the Use & Care Manual. Should a product difficulty occur, you must, at your expense, deliver or ship your ECHO unit to an authorized ECHO servicing dealer for warranty repairs (within the applicable warranty period), and arrange for pick-up or return of your unit after the repairs have been made. For your nearest authorized ECHO servicing dealer, call ECHO’s Dealer Referral Center, at 1-800-432-ECHO or you can locate an ECHO servicing dealer at WWW.ECHO-USA.COM. Should you require assistance or have questions concerning ECHO’s Warranty Statement, you can contact our Consumer Product Support Department at 1-800-432-ECHO or contact us through the web at WWW.ECHO-USA.COM.
PRODUCT WARRANTY PERIOD RESIDENTIAL APPLICATION
• 5 YEAR WARRANTY - All units for residential, or non-income producing use will be covered by this limited warranty for five
(5) years from date of purchase.
EXCEPTIONS:
• Damage caused by: Failure to follow Use & Care Manual
• Failure to follow all chemical manufacturers’ instructions included on their label or elsewhere
• Failure to follow Storing/Maintaining Your Sprayer section in Use & Care manual Use of powder based chemicals with or in a piston pump sprayer Wear items including but not limited to: seals, gaskets, pistons, hoses, diaphragms, straps or any wear item. These items are covered for 90 days from date of purchase. Any mis-use of product is not covered including but not limited to: using un-approved chemicals or parts, un-approved uses, using damaged or missing units/parts during operation, or modifying your sprayer in any manner.
COMMERCIAL APPLICATION
• 2 YEAR WARRANTY - All units for commercial, institutional, agricultural, industrial, or income producing use will be covered
by this limited warranty for two (2) years from the date of purchase.
EXCEPTIONS:
• Failure to read and follow Use & Care Manual
• Failure to follow all chemical manufacturers’ instructions included on their label or elsewhere
• Failure to follow Storing/Maintaining Your Sprayer section in Use & Care Manual Use of powder based chemicals with or in a piston pump sprayer Wear items including but not limited to: seals, gaskets, pistons, hoses, diaphragms, straps or any wear item. These items are covered for 30 days from date of purchase. Any mis-use of product is not covered including but not limited to: using un-approved chemicals or parts, un-approved uses, using damaged or missing units/parts during operation, or modifying your sprayer in any manner.
RENTAL APPLICATION - 90 DAYS WARRANTY
• Units for rental use will be covered against defects in material and workmanship for a period of 90 days from the date of purchase except for any of the above listed EXCEPTIONS.
PURCHASED REPAIR PARTS AND ACCESSORIES
90-day residential or non-income producing warranty except for any one of the above listed EXCEPTIONS
• 30-day commercial, institutional, agricultural, industrial, income producing, or rental application warranty except for any one of the above listed EXCEPTIONS
YOUR RECEIPT OF PURCHASE INCLUDING DATE, MODEL AND SERIAL NUMBER MUST BE MAINTAINED AND PRESENTED TO AN AUTHORIZED ECHO SERVICING DEALER FOR WARRANTY SERVICE. PROOF OF PURCHASE RESTS SOLELY WITH THE CUSTOMER. SOME STATES DO NOT ALLOW LIMITATIONS ON HOW LONG AN IMPLIED WARRANTY LASTS, SO THE ABOVE LIMITATIONS MAY NOT APPLY TO YOU. SOME STATES DO NOT ALLOW THE EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES, SO YOU MAY ALSO HAVE OTHER SPECIFIC LEGAL RIGHTS WHICH VARY FROM STATE TO STATE. THIS LIMITED WARRANTY IS GIVEN BY ECHO INCORPORATED, 400 OAKWOOD RD., LAKE ZURICH, IL 60047.
DISCLAIMER OF IMPLIED WARRANTIES
THIS LIMITED WARRANTY IS IN LIEU OF ALL OTHER EXPRESSED OR IMPLIED WARRANTIES, INCLUDING ANY WARRANTY OF FITNESS FOR A PARTICULAR PURPOSE OR USE AND ANY IMPLIED WARRANTY OF MERCHANTABILITY OTHERWISE APPLICABLE TO THIS PRODUCT. ECHO AND ITS AFFILIATED COMPANIES SHALL NOT BE LIABLE FOR ANY SPECIAL INCIDENTAL OR CONSEQUENTIAL DAMAGE, INCLUDING LOST PROFITS. THERE ARE NO WARRANTIES EXTENDED OTHER THAN AS PROVIDED HEREIN. THIS LIMITED WARRANTY MAY BE MODIFIED ONLY BY ECHO.
Repair parts and accessories replaced under this warranty are
Loading...