Echo MS-31H User Manual
WARNING
WARNING: Improper use or failure to follow instructions can result in explosive failure causing serious
eye or other injury. For safe use of this product you must read and follow all instructions. Do not leave a pres-
surized sprayer in the hot sun. Heat can cause pressure build-up resulting in possible explosion. Do not store or
leave solution in tank after use. Always wear goggles, gloves, long sleeve shirt, long pants and full foot protection when spraying. Never use any tool to remove pump if there is pressure in sprayer. Never stand with face or
body over top of tank when pumping or loosening pump to prevent ejecting pump assembly and/or solution
from striking and injuring you. Never pressurize sprayer by any means other than the original pump. Do not
attempt to modify this sprayer. Replace parts only with manufacturer’s original parts. Never spray ammable,
caustic, acidic, chlorine, bleach or other corrosive solutions or heat, pressure, or gas producing chemicals.
Always read and follow chemical manufacturer’s instructions before use with this sprayer as some chemicals may be hazardous when used with this sprayer.
WARNING: Handling the brass parts of this product
will expose you to lead, a chemical known to the
State of California to cause birth defects and other
reproductive harm. Wash hands after handling.
ECHO, INCORPORATED
400 Oakwood Road
Lake Zurich, IL 60047
www.echo-usa.com
Sk-1154-1
Parts, Piezas, Pièces
99944100484
Flat Fan Nozzle
Tobera
Buse
99944100480
Extension wand, Vara de extensión, Lance de rallonge
Elbow O-ring Hose Washer
Nozzle Gasket Wand O-ring
99944100482
Brass Adjustable Nozzle
Tobera
Buse
99944100486
Wand O-ring Kit
Kit del anillo “O”
Trousse de joint torique
99944100479
Hose Assembly
Ensamblaje de la manguera
Assemblage de boyau
Model# MS-21H Model# MS-31H
99944100483
Poly Adjustable Nozzle
Tobera
Buse
569033
Pressure Relief Valve
Válvula de descarga de presión
Soupape de décompression
99944100485
Nozzle Kit
Tobera
Buse
99944100478
Shut-o Assembly
Unidad de cierre
Assemblage d’arrêt
99944100477
Shut-of Valve Repair Kit
Kit de reparación para la válvula
de cierre.
Trousse de réparation de robinet
d’arrêt.
569034
Repair Kit
Juego de reparación
Kit de réparation
Note: Your particular sprayer may not include all parts pictured above.
Nota: Es posible que este pulverizador en particular no incluya todas las partes que se ilustran arriba.
Remarque : Votre pulvérisateur particulier pourrait ne pas inclure toutes les pièces illustrées plus haut.
013544 (A) R0514
1. Hose to Tank
1A
Outlet Tube
Adapter
1C
Outlet
Tube
1B
1D
No
Gap
Outlet
Tube
Outlet Tube
Adapter
Discharge
Assembly
1E
Tab/
Tank
Notch
Adapter
Discharge/ Assembly
• Make sure white outlet tube is attached to outlet tube adapter (Fig. 1A).
• Insert the outlet tube portion of the discharge assembly into the tank adapter (Fig. 1B).
• Proper placement of white outlet tube (Fig. 1C).
• Firmly insert the outlet tube adapter into the tank adapter (Fig. 1D) Lining up tab
with notches on the tank adapter.
• Firmly tighten the retaining nut to the tank adapter (Fig. 1E).
Retaining Nut Securely tightened.
2. Assembly of Shut-off, Extension Wand and Nozzle
2a
Shut-o Assembly
1) Screw nozzle assembly onto threaded end of the extension wand securely.
2) Insert unthreaded end of extension wand into shut-o assembly as shown and tighten retaining
nut securely.
Retaining Nut
Extension Wand
Nozzle Assembly
Nozzle Assembly
Figure 1-2
Unscrew the nozzle cap (1) from the nozzle body (3) with retaining nut (2) fastened tightly to the elbow (5). Unscrew the retaining nut
(2). Push the nozzle body (3) with the nozzle gasket (4) out of the retaining nut (2). To reinstall the nozzle, reverse the above instructions.
Figure 3
Unscrew the retaining nut from the elbow and push the fan nozzle tip and gasket out of the retaining nut. To reinstall the nozzle, reverse
the above instructions.
3. Filter
e lter helps prevent clogging while spraying. It is located on the end of the white tube inside
your sprayer tank.To clean lter, remove the hose from the tank and lift out the outlet tube. Make
sure the lter is positioned at the bottom of the tank as pictured.
3a
Filter
Loading...