Echo MS-20H, MS-30H User Manual

WARNING!

Hazard: Improper use or failure to follow instructions can result in explosive failure causing serious eye or other injury. For safe use of this product you must read and follow all instructions. Do not leave a pressurized

sprayer in the hot sun. Heat can cause pressure build-up. Do not store or leave solution in tank after use. Always

wear goggles, gloves, long sleeve shirt, long pants and full foot protection when spraying. Never use any tool to remove pump if there is pressure in sprayer. Never stand with face or body over top of tank when pumping or

loosening pump to prevent ejecting pump assembly and/or solution from striking and injuring you. Never pressurize sprayer by any means other than the original pump. Do not attempt to modify or repair this product except with original manufacturer’s parts. Never spray ﬂammable materials or heat, pressure, or gas producing

chemicals. Always read and follow manufacturer’s instructions before ﬁlling this sprayer as some chemicals may be hazardous when used with this sprayer.

WARNING: Handling the brass parts of this product

will expose you to lead, a chemical known to the State of California to cause birth defects and other reproductive harm. Wash hands after handling.

ECHO, INCORPORATED 400 Oakwood Road Lake Zurich, IL 60047 www.echo-usa.com

Parts, Piezas, Pièces

99944100484 Flat Fan Nozzle

Tobera Buse

99944100480

Extension wand, Vara de extensión, Lance de rallonge

Elbow O-ring Hose Washer

Nozzle Gasket Wand O-ring

99944100482 Brass Adjustable Nozzle

Tobera Buse

Retaining Nut

Filter

99944100486

Wand O-ring Kit Kit del anillo “O” Trousse de joint torique

99944100479 Hose Assembly

Ensamblaje de la manguera Assemblage de boyau

Model# MS-20H

99944100483 Poly Adjustable Nozzle

Tobera Buse

99944100485 Nozzle Kit

Tobera Buse

“C” C ip C ip de “C” Clip de « C »

Model# MS-30H

99944100478

Shut-oﬀ Assembly Unidad de cierre Assemblage d’arrêt

99944100477 Shut-oﬀf Valve Repair Kit

Kit de reparación para la válvula de cierre. Trousse de réparation de robinet d’arrêt.

99944100487 Repair Kit

Juego de reparación Kit de réparation

Note: Your particular sprayer may not include all parts pictured above. Nota: Es posible que este pulverizador en particular no incluya todas las partes que se ilustran arriba. Remarque : Votre pulvérisateur particulier pourrait ne pas inclure toutes les pièces illustrées plus haut.

Repair Parts Kit Gaskets and Seals (not included), Juego de piezas de reparación, empaquetaduras y juntas (no incluido) Kit de pièces de réparation, joints et garniture d’étanchéité (non inclus) 6-5387

011296 (A) R0910

1. Hose to Tank

Outlet Tube Adapter

No Gap

Outlet Tube

Outlet Tube Adapter

Outlet Tube

Discharge Assembly

Tank Adapter

Tab/ Notch

Retaining Nut Securely tightened.

Discharge/ Assembly

• Make sure white outlet tube is attached to outlet tube adapter (Fig. 1A).

• Insert the outlet tube portion of the discharge assembly into the tank adapter (Fig. 1B).

• Proper placement of white outlet tube (Fig. 1C).

• Firmly insert the outlet tube adapter into the tank adapter (Fig. 1D) Lining up tab with notches on the tank adapter.

• Firmly tighten the retaining nut to the tank adapter (Fig. 1E).

2. Assembly of Shut-off, Extension Wand and Nozzle

Shut-oﬀ Assembly

Retaining Nut

Extension Wand

1) Screw nozzle assembly onto threaded end of the extension wand securely.

2) Insert unthreaded end of extension wand into shut-oﬀ assembly as shown and tighten retaining nut securely.

Nozzle Assembly

Figure 1-2

Unscrew the nozzle cap (1) from the nozzle body (3) with retaining nut (2) fastened tightly to the elbow (5). Unscrew the retaining nut (2). Push the nozzle body (3) with the nozzle gasket (4) out of the retaining nut (2). To reinstall the nozzle, reverse the above instructions.

Figure 3

Unscrew the retaining nut from the elbow and push the fan nozzle tip and gasket out of the retaining nut. To reinstall the nozzle, reverse the above instructions.

3. Filter

e ﬁlter helps prevent clogging while spraying. It is located on the end of the white tube inside your sprayer tank.To clean ﬁlter, remove the hose from the tank and lift out the outlet tube. Make sure the ﬁlter is positioned at the bottom of the tank as pictured.

Filter

4. Pre-Use Check

1) Do: Check tightness of hose nut to be sure hose is securely attached to the tank outlet.

2) Do: Inspect hose for deterioration, cracks, softness, or brittleness. If any of these conditions are found, replace hose before using. Replace with original manufacturer’s parts only.

3) Do: Remove pump (see Filling, Pressurizing and Spraying Instructions), inspect interior and exterior of tank for signs of deterioration of body and bottom. Any sign of deterioration indicates possible tank weakening and could result in explosive bursting under pressure. If any of these signs are found, discard tank immediately and replace. Do not attempt to patch leaks, etc., as this could result in serious injury.

4) Do: Follow Filling, Pressurizing and Spraying Instructions, except use water only.

5) Do: Pump plunger 10-20 strokes and inspect for leaks.

6) Do: Direct shut-oﬀ away from you and open to make sure discharge is not clogged.

7) Do: If unit passes this test, release pressure (see Pressure Releasing Instructions), empty tank, and proceed with Filling, Pressurizing and Spraying Instructions.

5. Filling

1) Do: Turn pump handle counterclockwise and remove pump

2) Do: Prepare spray solution following all directions and safety warnings on chemical label.

3) Do: Fill tank to no more than the proper gallon marker. Do NOT: overﬁll to accommodate pump.

4) Do: Check pump to make sure that no grass or dirt is stuck to barrel. Replace pump in tank and tighten securely.

6. Pressurizing and Spraying

Turn handle clockwise to tighten. Push handle down, turn1/4 turn counterclockwise to release.

7. To Release Pressure

Your sprayer is equipped with a pressure relief release valve. To release pressure lift and hold the cap until air is completely exhausted, OR, turn the valve slowly counterclockwise until you hear air escaping and wait until air is completely exhausted.

6b 6c

Pump until you feel resistance.

Push handle, down, turn 1/4 turn clockwise to lock. Begin spraying. Re-pump sprayer as required to maintain spray force.

8. Care, Storage and Maintenance

1) Do: Rinse tank thoroughly with water only, empty, reﬁll with water. Follow Filling, Pressurizing and Spraying Instructions, except pump unit 8-10 strokes.

2) Do: Open shut-oﬀ and allow water to run through discharge assembly.

3) Do: Release pressure (Follow Pressure Release Instructions), remove pump and empty sprayer.

4) Do: Store sprayer tank upside down, with pump removed, in a warm dry location.

5) Do: Periodically oil pump by dropping 10-12 drops of light oil down pump rod through opening in cover.

9. Fatigue-free spraying

LOCK-OFF POSITION LOCK-ON POSITION NEUTRAL POSITION

Locking Mechanism

Handle

Down

Handle

For safety lock-oﬀ feature (no-spraying), pull up on handle and move red locking mechanism into lock-oﬀ position as shown in ﬁg. 9a. To disengage, push down on handle and return red locking mechanism to neutral position as in ﬁg. 9c. For lock-on feature (continuous spraying), push down on handle and move red locking mechanism into lock-on position as shown in ﬁg. 9b. To disengage, push down on handle and return red locking mechanism to neutral position as shown in ﬁg. 9c.

If the handle fails to operate correctly, release the pressure from the tank by turning the pressure release knob on the tank . Inspect and repair the handle assembly or replace with a new handle assembly.

+ 4 hidden pages