Echo HC-2410 User Manual

Hedge Clipper

Operator's Manual

MODELS:

HC-1500 Serial Number 001001 - 999999 HC-1500 - Type 2E Serial Number 001001 - 672900 HC-1600 Serial Number 001001 - 999999 HC-1600 - Type 1E Serial Number 001001 - 526700 HC-2000 Serial Number 001001 - 999999 HC-2000 - Type 1E Serial Number 001001 - 523200 HC-2400 Serial Number 001001 - 999999 HC-2410 Serial Number 001001 - 999999

X7502248103

W ARNING

The engine exhaust from this

product contains chemicals known

to the State of California to cause

cancer, birth defects or other

reproductive harm.

WARNING DANGER

Read rules for safe operation and all instructions carefully. ECHO provides this Operator's Manual and a Safety Manual. Both must be read and understood for proper and safe operation.

89861105635 12/00

EDGE CLIPPER

PERATOR'S

MANUAL SAFETY SYMBOLS AND IMPORT ANT INFORMATION

Throughout this manual and on the product itself, you will find safety alerts and helpful, information messages preceded by symbols or key words. The following is an explanation of those symbols and key words and what they mean to you.

This symbol accompanied by the words WARNING and DANGER calls attention to an act or condition that can lead to serious personal injury to operator and bystanders.

IMPORTANT

The enclosed message provides

The circle with the slash symbol means whatever is shown within the circle is prohibited.

information necessary for the protection of the unit.

NOTE

This enclosed message provides tips for use, care and maintenance of the unit.

ANUAL

SAFETY

DECALS

Locate these safety decals on your unit. The complete unit illustration found in the "DESCRIPTION" section, will help you locate them. Make sure the decals are legible and that you understand and follow the instructions on them. If a decal cannot be read, a new one can be ordered from your ECHO dealer. See PARTS ORDERING instructions for specific information.

ALL HEDGE CLIPPER MODELS

P/N X505000270

HC-2000, HC-2400, HC-2410 ONLY

HC-1500, HC-1600 ONLY

P/N X505000290

INTERNATIONAL SYMBOLS

Symbol form/shape

Symbol

description/application

Read and understand

owners manual.

Symbol form/shape

Symbol

description/application

Fuel and oil mixture

Symbol form/shape

Symbol

description/application

Carburetor adjustment

- Low speed mixture

Symbol form/shape

Symbol

description/application

Carburetor adjustment

- High speed mixture

Wear eyes, ears and

head protection

Emergency stop

Wear hand protec-

tion. Use two handed.

Engine choke

control.

Chain lubrication

Ignition

Finger Severing

Hot

Surface

DO NOT smoke

near fuel.

Ignition ON/OFF

Do not operate without guards

in place.

EQUIPMENT

Before operation a complete check of the unit must be performed;

• Check unit for loose/missing nuts, bolts and screws. Tighten and/or replace as needed.

• Inspect fuel lines, tank and area around carburetor for fuel leaks. DO NOT operate unit if leaks are found.

Safety/Alert

Avoid all power

lines. This unit is not

insulated against

electrical current.

Plan retreat path

from falling

objects.

DO NOT allow

flames or sparks

near fuel.

Carburetor adjustment

- Idle speed

Do not operate clos-

er than 15 M (50 ft.) from electrical haz-

ards.

Primer bulb

Wear slip resistant

foot wear.

Keep bystanders at least

4.5 meters (15 feet) away.

• Never adjust blades when the engine is operating.

• Inspect hand guard for damage. Replace if damaged or missing.

• Check that the blade assembly is firmly attached and in safe operating condition. Dull, loose or damaged blades should not be used.

• ECHO, INC. will not be responsible for the failure of cutting devices or accessories which have not been tested and approved by ECHO for use with this unit.

FUEL

W ARNING DANGER

Fuel is VERY flammable. Use extreme care when mixing, storing or handling or serious personal injury may result.

• Use an approved fuel container.

• DO NOT smoke near fuel.

• DO NOT allow flames or sparks near fuel.

• Fuel tanks/cans may be under pressure. Always loosen fuel caps slowly allowing pressure to equalize.

• NEVER refuel a unit when the engine is HOT!

• NEVER refuel a unit with the engine running.

• DO NOT fill fuel tanks indoors. ALWAYS fill fuel tanks outdoors over bare ground.

• Securely tighten fuel cap after refueling.

• Inspect for fuel leakage. If fuel leakage is found, do not start or operate unit until leakage is repaired.

PERATOR'S

EDGE CLIPPER

ANUAL

IMPORTANT

Spilled fuel is a leading cause of hydrocarbon emissions. Some states may require the use of automatic fuel shut-off containers to reduce fuel spillage. Contact your ECHO dealer for ordering information.

After Refueling;

• Wipe any spilled fuel from the unit.

• Move at lease 3 m (10 ft.) from refueling location before starting the engine.

After use;

• DO NOT store a unit with fuel in its tank. Leaks can occur. Return unused fuel to an approved fuel storage container.

PERSONAL CONDITION AND SAFETY EQUIPMENT

3 m (10 ft.)

W ARNING DANGER

Hedge Clipper users risk injury to themselves and others if the hedge clipper is used improperly and or safety precautions are not followed. Proper clothing and safety gear must be worn when operating a hedge clipper.

Physical Condition --

Your judgment and physical dexterity may not be good:

• if you are tired or sick,

• if you are taking medication,

• if you have taken alcohol or drugs Operate unit only if you are physically and mentally well.

Eye Protection --

Eye protection that meet ANSI Z87.1 or CE requirements must be worn whenever you operate the Hedge Clipper.

Hand Protection --

Wear no-slip, heavy duty work gloves to improve your grip on the handles. Gloves also reduce the transmission of machine vibration to your hands.

Hearing Protection --

Wear hearing protection. ECHO recommends wearing hearing protection whenever unit is used.

Proper Clothing --

Wear snug fitting, durable clothing;

• Pants should have long legs, shirts with long sleeves.

• DO NOT WEAR SHORTS,

• DO NOT WEAR TIES, SCARFS, JEWELRY. Wear protective hair covering to contain long hair. Wear sturdy work shoes with nonskid soles;

• DO NOT WEAR OPEN TOED SHOES,

• DO NOT OPERATE UNIT BAREFOOTED. Wear no-slip, heavy duty work gloves.

Hot Humid Weather --

Heavy protective clothing can increase operator fatigue which may lead to heat stroke. Delay heavy work until temperature drops.

SAFE OPERATION

Determine Operation Area

• Do not operate this product indoors or in inadequately ventilated areas.

• Review the area to be trimmed. Look for hazards that could contribute to unsafe conditions.

PERATOR'S

EDGE CLIPPER

ANUAL

• Spectators and fellow workers must be warned, and children and animals prevented from coming nearer than 4.5 m (15 ft.) while the Hedge Clipper is in use.

• Provide all users of this equipment with the Operator's Manual and instructions for Safe Operation.

Operation

Use Proper Clothing & Equipment

• Before starting the unit, equip yourself and any other person working within the 4.5 m (15 ft.) Safety Zone with the required Protective Equipment and clothing.

Keep a Solid Stance

• Maintain footing and balance at all times. Do not stand on slippery, uneven or unstable surfaces. Do not work in odd positions or on ladders. Do not over reach.

Keep a Firm Grip

• Hold the front and rear handles with both hands, with thumbs and fingers encircling the handles.

4.5 m (15 ft.)

Avoid Hot Surfaces

• During operation, the complete unit, especially the power head, muffler area and cutting attachment may become very hot, too hot to touch.Avoid contact during and immediately after operation.

EXTENDED OPERATION/EXTREME CONDITIONS

Vibration and Cold

It is believed that a condition called Raynaud’s Phenomenon, which affects the fingers of certain individuals may be brought about by exposure to vibration and cold. Exposure to vibration and cold may cause tingling and burning sensations followed by loss of color and numbness in the fingers. The following precautions are strongly recommended because the minimum exposure which might trigger the ailment is unknown.

• Keep your body warm, especially the head, neck, feet, ankles, hands and wrists.

• Maintain good blood circulation by performing vigorous armexercises during frequent work breaks and also by not smoking.

• Limit the hours of operation. Try to fill each day with jobs where operating the trimmer or other hand-held power equipment is not required.

• If you experience discomfort, redness and swelling of the fingers followed by whitening and loss of feeling, consult your physician before further exposing yourself to cold and vibration.

Repetitive Stress Injuries

It is believed that overusing the muscles and tendons of the fingers, hands, arms and shoulders may cause soreness, swelling, numbness, weakness and extreme pain in those areas. Certain repetitive hand activities may put you at a high risk for developing a Repetitive Stress Injury (RSI). An extreme RSI condition is Carpal Tunnel Syndrome (CTS), which could occur when your wrist swells and squeezes a vital nerve that runs through the area. Some believe that prolonged exposure to vibration may contribute to CTS. CTS can cause severe pain for months or even years. To reduce the risk of RSI/CTS, do the following:

• Avoid using your wrist in a bent, extended or twisted position. Instead try to maintain a straight wrist position. Also, when grasping, use your whole hand, not just the thumb and index finger.

• Take periodic breaks to minimize repetition and rest your hands.

• Reduce the speed and force with which you do the repetitivemovement.

• Do exercises to strengthen the hand and arm muscles.

• Immediately stop using all power equipment and consult a doctor if you feel tingling, numbness or pain in the fingers, hands, wrists or arms. The sooner RSI/CTS is diagnosed, the more likely permanent nerve and muscle damage can be prevented.

PERATOR'S

EDGE CLIPPER

ANUAL

DESCRIPTION

The ECHO product you purchased has been factory pre-assembled for your convenience.

After opening the carton, check for damage. Immediately notify your retailer or ECHO Dealer of damaged or missing parts. Use the contents list to check for missing parts.

CONTENTS

__ 1 - Hedge Clipper Assembly __ 1 - Operators Manual __ 1 - Safety Manual __ 1 - Warranty Statement __ 1 - Warranty Registration Card __ 1 - Plastic Bag __ - T-Wrench __ - 8 mm x 10 mm Open end Wrench __ - Bottle 2.6 oz. 2-Cycle Oil __ 1 - Blade Cover

EMISSION CONTROL - Emissions Models

The emission control system for this engine is EM (Engine Modification).

IMPORT ANT ENGINE INFORMA TION ENGINE FAMIL Y : TEH021UB24RA DISPLACEMENT : 21.2cc THIS ENGINE MEETS U.S. EPA PHI AND 1995 - 1999 CALIFORNIA EMISSION REGULATIONS FOR ULGE ENGINES. REFER TO OWNER’S MANUAL FOR MAINTENANCE SPECIFICATIONS AND ADJUSTMENTS.

Emission Control Label (located on Engine) (EXAMPLE ONLY, information on label varies by FAMILY).

HC-1500, 1600

HC-2000, 2400, 2410

EDGE CLIPPER

PERATOR'S

1. OPERATOR'S MANUAL - Read and understand this manual before operation. Keep manual in a safe

location for future reference, i.e., operation, maintenance, storage and specifications.

2. SAFETY MANUAL - Read and understand this manual before operation. Keep manual in a safe location of

safe operating techniques.

3. POWER HEAD - Factory Assembled to the gear housing assembly. Includes the Engine, Clutch, Fuel

System, Ignition System and Recoil Starter.

4. REAR HANDLE - HC-1500, 1600. Contains the Stop Switch, Throttle Lockout and Throttle Trigger.

5. LEFT HAND REAR HANDLE - HC-2000, 2400, 2410. Contains the Stop Switch, Throttle Lockout and

Throttle Trigger.

6. FRONT HANDLE / GUARD -

HC-1500, 1600. Comfortable, textured finish provides anti-slip grip for front hand. Guard protects hand from the blades. Warning decals are located on guard. HC-2000, 2400 and HC-2410. Right Hand Handle, Rubber anti-slip grip, guard protects hand from the blades. Warning decals are located on guard.

7. STOP SWITCH -

HC-1500. "TOGGLE SWITCH" located on the left side of the rear handle. Move switch UP to RUN, DOWN to STOP.

ANUAL

HC-1600, HC-2000, 2400, 2410 "SLIDE SWITCH" mounted on top of the left hand rear handle. Move switch FORWARD to RUN, BACK to STOP.

8. THROTTLE TRIGGER LOCKOUT - This lever must be depressed before Throttle Trigger can be activated.

9. THROTTLE TRIGGER - Spring loaded to return to idle when released. Trigger Lockout must be depressed fully

before Throttle Trigger will move. During acceleration, depress gradually for best operating technique.

10. BLADES - Double reciprocating blades mounted to a blade support bar. Models HC-1500, HC-1600 are double sided

blades, meaning they are capable of cutting on either side of the blade. All other models are single sided.

11. AIR CLEANER - Contains replaceable filter element.

12. PRIMER BULB - Pumping primer bulb before starting engine draws fresh fuel from the fuel tank priming the carbure-

tor for starting. Pump primer bulb until fuel is visible and flows freely in the clear fuel tank return line. Pump bulb an additional 4 or 5 times.

13. CHOKE - The choke control lever is located on the top of the choke case. Move to "COLD START" to close the

choke for Cold Starting. Move to "RUN" position to open choke.

14. RECOIL STARTER HANDLE - Pull handle slowly until recoil starter engages, then quickly and firmly. DO NOT pull

rope all the way out or allow the handle to snap back, damage to the starter will occur.

15. FUEL TANK - Contains fuel and fuel filter.

16. FUEL TANK CAP - Covers and seals fuel tank opening.

17. SPARK PLUG - Provides spark to ignite fuel mixture.

18. MUFFLER/SPARK ARRESTOR - The muffler controls the exhaust noise while the spark arrestor prevents hot,

glowing particles of carbon from leaving the muffler where they could possibly start a fire.

19. BLADE COVER - Used to cover blades during transportation or storage. Remove blade cover before using unit.

20. SAFETY VIDEO - (Not included with unit) P/N 99922202800 English version only is available at a cost of $5.00 from

ECHO, INC. or any authorized ECHO dealer. The video overviews safety precautions and proper operating techniques and is supplemental to the Safety Manual. Read and understand the Safety Manual for complete information on safe operation.

+ 23 hidden pages