Grass Trimmer
Operator's Manual
MODEL GT-2000EZR
Serial Number 03001001 - 03999999
X7702273900
W ARNING DANGER
Read rules for safe operation and instructions carefully. ECHO provides an Operator's
Manual and a Safety Manual. Both must be read and understood for proper and safe
operation.
X770000370
01/02
GRASS TRIMMER
OPERATOR'S MANUAL
MANUAL SAFETY SYMBOLS AND IMPORTANT INFORMATION
Throughout this manual and on the product itself, you will find safety
alerts and helpful, information messages preceded by symbols or key
words. The following is an explanation of those symbols and key words
and what they mean to you.
This symbol accompanied by the words
WARNING and DANGER calls attention to an
act or condition that can lead to serious personal
injury to operator and bystanders.
IMPORTANT The enclosed message
provides information necessary for the
protection of the unit.
3
The circle with the slash symbol means whatever is
shown within the circle is prohibited.
NOTE This enclosed message provides tips
for use, care and maintenance of the unit.
SAFETY
DECALS
Locate these safety decals on your unit. The complete unit illustration found in the "DESCRIPTION" section, will help
you locate them. Make sure the decals are legible and that you understand and follow the instructions on them. If a
decal cannot be read, a new one can be ordered from your ECHO dealer. See PARTS ORDERING instructions for specific
information.
P/N 89031744530
W ARNING DANGER
C. SHIELD DECAL
B. SPANISH DECAL
ADVERTENCIA PELIGRO
Esta unidad puede ser peligrosa y producir
lesiones personales graves si no se usa en
forma adecuada. Para reducir el riesgo de
lesionarse, los operadores, los ayudantes y los
espectadores deben leer y comprender el
890228-09560
Manual Del Operador y los Manuales De
Seguridad que se entregan escritos en español.
•This unit can be dangerous and cause serious injury if improperly used. • Operators, helpers and bystanders can be severely
in jured by thrown objects and must wear specified ANSI Z87.1 eye protection. Blindness or loss of eye can occur. Do not rely
on cutter head shield to protect eyes. Ricochet can occur. •to avoid accidental contact, keep everyone beyond operating area.
•To reduce the risk of injury to operator, helpers & bystanders, read and understand your operator's and safety manuals. For
a free copy of the safety Manual, write to ECHO, INCORPORATED, 400 Oakwood Road, Lake Zurich, IL 60047. •Keep shield
and other components in place and in good condition. Do not use attachments or other parts not approved by ECHO. GT style
(non-blade capable) units must not be converted to blade use except Maxi-Cuts or similar ECHO approved attachments.
ENGLISH TRANSLATION
W ARNING DANGER
This unit can be dangerous and cause serious
injury if improperly used. To reduce injury
risk to operator, helpers and bystanders, read
and understand the Operator's and Safety
Manuals, which are provided in Spanish.
4
INTERNA TIONAL SYMBOLS
SYMBOL FORM/
SHAPE
SYMBOL
DESCRIPTION/APPLICATION
Read and understand
Operator's Manual.
SYMBOL FORM/
SHAPE
SYMBOL
DESCRIPTION/APPLICATION
FUEL AND OIL
MIXTURE
SYMBOL FORM/
SHAPE
SYMBOL
DESCRIPTION/APPLICATION
DO NOT ALLOW
FLAMES OR
SPARKS NEAR
FUEL.
SYMBOL FORM/
SHAPE
SYMBOL
DESCRIPTION/APPLICATION
EMERGENCY STOP
WEAR EYES, EARS
AND HEAD
PROTECTION
HOT
SURFACE
WEAR HAND AND
FOOT PROTECTION
SAFETY/ALERT
KEEP BYSTANDERS AND HELPERS
SAFETY INSTRUCTIONS
PERSONAL
CONDITION AND SAFETY EQUIPMENT
FINGER SEVERING
WEAR SLIP
RESISTANT
FOOT WEAR.
DO NOT SMOKE
NEAR FUEL.
AWAY 15 M (50 FT.).
ENGINE CHOKE
CONTROL.
PRIMER
BULB
DO NOT EXCEED
10,000 RPM.
DO NOT OPERATE
WITHOUT
GUARDS AND
SHIELDS IN
PLACE.
DO NOT USE
BLADES. STRING
LINE ONLY
IGNITION
ON/OFF
CARBURETOR
ADJUSTMENT
- HIGH SPEED
MIXTURE
CARBURETOR
ADJUSTMENT
- LOW SPEED
MIXTURE
CARBURETOR
ADJUSTMENT
- IDLE SPEED
BEWARE
- THROWN,
RICOCHET
OBJECTS
W ARNING DANGER
Trimmer/Brush Cutter users risk injury to themselves and others if the trimmer/brush cutter is used improperly and or
safety precautions are not followed. Proper clothing and safety gear must be worn when operating a trimmer.
Eye Protection
Wear eye protection that meets ANSI Z87.1 or CE
requirements whenever you operate the trimmer.
Hand Protection
Wear no-slip, heavy duty work gloves to improve your
grip on the Trimmer/Brush Cutter handles. Gloves also
reduce the transmission of machine vibration to your
hands.
Hearing Protection
ECHO recommends wearing hearing protection whenever
unit is used.
Proper Clothing
Wear snug fitting, durable clothing;
• Pants should have long legs, shirts with long sleeves.
• DO NOT WEAR SHORTS,
• DO NOT WEAR TIES, SCARVES, JEWELRY.
Wear sturdy work shoes with non-skid soles;
• DO NOT WEAR OPEN TOED SHOES,
• DO NOT OPERATE UNIT BAREFOOTED.
EXTENDED OPERATION/EXTREME CONDITIONS
Vibration and Cold --
It is believed that a condition called Raynaud’s Phenomenon, which
affects the fingers of certain individuals may be brought about by
exposure to vibration and cold. Exposure to vibration and cold may
cause tingling and burning sensations followed by loss of color and
numbness in the fingers. The following precautions are strongly
recommended because the minimum exposure which might trigger the
ailment is unknown.
• Keep your body warm, especially the head, neck, feet, ankles, hands
and wrists.
• Maintain good blood circulation by performing vigorous arm exercises during frequent work breaks and also by not smoking.
• Limit the hours of operation. Try to fill each day with jobs where
operating the trimmer or other hand-held power equipment is not
required.
• If you experience discomfort, redness and swelling of the fingers
followed by whitening and loss of feeling, consult your physician
before further exposing yourself to cold and vibration.
Repetitive Stress Injuries --
It is believed that overusing the muscles and tendons of the fingers,
hands, arms and shoulders may cause soreness, swelling, numbness,
weakness and extreme pain in those areas. Certain repetitive hand
activities may put you at a high risk for developing a Repetitive Stress
Injury (RSI). An extreme RSI condition is Carpal Tunnel Syndrome
(CTS), which could occur when your wrist swells and squeezes a vital
nerve that runs through the area. Some believe that prolonged exposure
to vibration may contribute to CTS. CTS can cause severe pain for
months or even years.
GRASS TRIMMER
OPERATOR'S MANUAL
To reduce the risk of RSI/CTS, do the
following:
• Avoid using your wrist in a bent, extended
or twisted position. Instead try to maintain
a straight wrist position. Also, when
grasping, use your whole hand, not just
the thumb and index finger.
• Take periodic breaks to minimize repetition
and rest your hands.
• Reduce the speed and force in which you
do the repetitive movement.
• Do exercises to strengthen the hand and
arm muscles.
• Immediately stop using all power equipment and consult a doctor if you feel
tingling, numbness or pain in the fingers,
hands, wrists or arms. The sooner RSI/
CTS is diagnosed, the more likely permanent nerve and muscle damage can be
prevented.
5
EQUIPMENT
W ARNING DANGER
Use only ECHO approved attachments. Serious injury may result from the use of a non approved attachment combination. ECHO, INC. will not be responsible for the failure of cutting devices, attachments or accessories which have
not been tested and approved by ECHO. Read and comply with all safety instructions listed in this manual and safety
manual.
• Check unit for loose/missing nuts, bolts and screws. Tighten and/or
replace as needed.
• Inspect fuel lines, tank and area around carburetor for fuel leaks.
DO NOT operate unit if leaks are found.
• Inspect shield for damage and ensure that the cut-off knife issecurely
in place. Replace if either is damaged or missing.
• Check that the cutting attachment is firmly attached and in safe
operating condition.
• Check that front (loop) handle and optional shoulder/waist harness
are adjusted for safe, comfortable operation. See Assembly for proper
adjustment.
• Have repairs done only by an authorized ECHO Service Dealer.
• Keep exhaust area clear of flammable debris. Avoid contact during
and immediately after operation.
6
SAFE OPERATION
W ARNING DANGER
Do not operate this product indoors or in inadequately ventilated
areas. Engine exhaust contains poisonous emissions and can cause
serious injury or death.
• Provide all operators of this equipment with the Operator's Manual
and instructions for safe operation.
Keep A Firm Grip
• Hold the front and rear handles with both hands with thumbs and
fingers encircling the handles
Keep A Solid Stance
• Maintain footing and balance at all times. Do not stand on slippery,
uneven or unstable surfaces. Do not work in odd positions or on
ladders. Do not over reach.
EMISSION CONTROL
EPA Phase 2
The emission control system for this engine is EM (Engine Modification).
Emission Control Label located on Engine
(EXAMPLE ONLY, information on label varies by FAMILY).
PRODUCT EMISSION DURABILITY
The 300 hour emission durability compliance period is the time span selected by the manufacturer certifying the
engine emissions output meets applicable emissions regulations, provided that approved maintenance procedures
are followed as listed in the Maintenance Section of this manual.
ENGINE FAMILY: 2EHXS.0214RA DISPLACEMENT: 21.2 CC
EMISSION COMPLIANCE PERIOD : 300 hours
THIS ENGINE MEETS U.S. EPA PHASE 2 EMISSION REGULATIONS FOR SMALL NON ROAD ENGINE. REFER TO
OWNER'S MANUAL FOR MAINTENANCE SPECIFICATIONS
AND ADJUSTMENTS.
IMPORTANT ENGINE INFORMATION
DESCRIPTION
The ECHO product you purchased has been factory pre-assembled for your convenience. Due to packaging restrictions,
shield installation and positioning of the front handle are necessary.
After opening the carton, check for damage. Immediately notify your retailer or ECHO Dealer of damaged or missing
parts. Use the contents list to check for missing parts.
CONTENT LIST
_____ 1 - Trimmer Assembly
_____ - Power Head
_____ - Drive Shaft Assembly
_____ 1 - Plastic Bag (Co-Pack)
_____ - Operator's Manual
_____ - Safety Manual
_____ - Shield Assembly
_____ 1 - Nylon Trimmer Head
_____ - 12, 8 in. x .080 Pre-cut Nylon Line
_____ - Hardware Bag
_____ - 1, Locking Tool
_____ - 1, Locknut 3/8-24
_____ - 1, Small Washer
_____ - 1, Large Washer
_____ - Warranty Card & Limited Warranty
_____ - Safety Glasses
_____ - Oil 2 Stroke
GRASS TRIMMER
OPERATOR'S MANUAL
18
17
7
10
19
5
4
7
6
3
16
11
15
14
13
2
1
8
12
9
8
1. POWER HEAD - Factory Assembled to the Drive shaft assembly. Includes the Engine, Clutch, Fuel System, Ignition
System and Recoil Starter.
2. GRIP - Rear (right hand) handle.
3. FRONT HANDLE - The Front (loop) handle is factory assembled to the Drive Shaft assembly but must be re-
positioned for proper cutting attitude and operator comfort.
4. DRIVE SHAFT ASSEMBLY - Factory Assembled to the Power Head. Includes the Rear (right hand) Handle
Assembly, Bearing Housing Assembly, Throttle Trigger, Front (loop, left hand) Handle Assembly, Flexible Drive
Cable and Safety Decals.
5. NYLON CUTTER HEAD - Contains replaceable nylon trimming lines.
6. DEBRIS SHIELD ASSEMBLY - Included in plastic bag (co-pack). MUST be installed on unit before use, see
Assembly Instructions. Shield assembly includes the Cut-Off Knife and Safety Decal. Mounts on the Bearing
Housing Assembly just above the cutting attachment. Helps protect the operator by deflecting debris produced
during the trimming operation.
7. CUT-OFF KNIFE - Trims line to the correct length (5"). If trimmer is operated without a cut-off knife the line will
become too long - more than (5") - the operating speed will slow, the engine overheat and performance will suffer.
8. THROTTLE TRIGGER - Spring loaded to return to idle when released. During acceleration, press trigger gradually
for best operating technique.
9. STOP SWITCH - "TOGGLE SWITCH" mounted on the engine. Move switch UP to RUN, DOWN to STOP.
10. ARM REST - Provides arm rest during operation and protects arm from hot engine.
11. SPARK ARRESTOR - CATALYTIC MUFFLER / MUFFLER -The muffler or catalytic muffler controls exhaust noise
and emission. The spark arrestor screen prevents hot, glowing particles of carbon from leaving the muffler. Keep
exhaust area clear of flammable debris.
12. FUEL TANK - Contains fuel and fuel filter.
13. FUEL TANK CAP - Cover and seals fuel tank opening.
14. RECOIL STARTER HANDLE/ROPE - Pull recoil starter handle/rope using light pulling force, approximately 2/3
(2 ft.) of rope length. Two (2) to Six (6) pulls are required to properly tension starter spring prior to automatic engine
engagement. DO NOT let handle snap back or damage to unit will occur.
15. PRIMER BULB - Pumping primer bulb before starting engine draws fresh fuel from the fuel tank priming the carbure-
tor for starting. Pump primer bulb until fuel is visible and flows freely in the clear fuel tank return line. Pump bulb an
additional 4 or 5 times.
16. AIR CLEANER - Contains replaceable filter element.
17. CHOKE - Located above the air cleaner housing. Controls operation of choke. Move choke to starting position
(Close Choke) and back to run position (Open Choke).
18. SPARK PLUG - Provides spark to ignite fuel mixture.
19. SAFETY VIDEO - (Not included with unit) P/N 99922202540 English version only is available at a cost of $5.00 from
ECHO, INC. or any authorized ECHO dealer. The video overviews safety precautions and proper operating techniques and is supplemental to the Safety Manual. Read and understand the Safety Manual for complete information
on safe operation.
SPECIFICATIONS
LEDOM RZE0002-TG
htgneL ).ni3.55(mm5041
htdiW ).ni4.21(mm513
thgieH ).ni2.41(mm063
daeHrettuC/w)yrd(thgieW ).bl0.01(gk55.4
epyTenignE enigneenilosagrednilycelgnis,ekorts-owt,deloocriA
eroB ).ni862.1(mm2.23
ekortS ).ni40.1(mm0.62
tnemecalpsiD ).ni.uc92.1(cc2.12
metsyStsuahxE relffuMrotserrAkrapS
GRASS TRIMMER
OPERATOR'S MANUAL
9
roterubraC remirp/wledommgarhpaidamaZ
metsySnoitingI egrahcsidroticapac,otengamleehwylF
gulPkrapS
leuF )liOekorts-owTdnaenilosaG(dexiM
oitaRliO/leuF lioenignedeloocriaekorts-owt,ecnamrofrePhgiHOHCE1:05
enilosaG
liO lioenignedeloocriaekorts-owt,ecnamrofrePhgiHOHCE1:05
yticapaCknaTleuF ).zo.lfSU0.41(.til4.0
metsySretratS tsissAretratSlioceRcitamotua-imeS
hctulC epyTlagufirtneC
tfahSevirD tfahSxelF"4/1
noitceriDgnitatoR potmorfdeweivesiwkcolC
daeHrettuC ).ni8(mm302yticapaceniL080.htiw)enil-2(daehenilnolyN
).ni620.0(mm56.0paGA7-MPBKGN
nahterom,lohoclalyhtemgniniatnocleufesuTONOD.dedaelnuenatcO98
.EBTM%51rolohoclalyhte%01
eldnaH pirG-thgiR,pooL-D-tfeL
ssenraHredluohS 10200244999N/PlanoitpO
)MPR(deepSeldI 0033-0062
).T.O.W(deepSelttorhTnepOediW
)MPR(daeHeniLnolyNhtiw
0087-0056
10
ASSEMBLY
PLASTIC
Tools Required: None
1 . Remove wing nut (C), washer (B), and bolt (A).
2. Snap the shield over the bearing housing.
3 . Install bolt (A), washer (B) and wing nut (C).
SHIELD
NYLON LINE HEAD
Tools Required: Head Locking Tool, 9/16 in. Socket
Parts Required: Rapid Loader
1 . Remove plastic threaded shaft sleeve from PTO shaft.
2 . Align locating hole in upper plate with hole in bearing housing and
insert 1/8 in. diameter locking tool (A).
3 . Place large washer then line head on threaded shaft followed by
small metal washer and locknut.
TM
Head.
B
C
A
A
4. Tighten locknut securely.
IMPORTANT
Remember to remove the locking tool.
NYLON LINE REPLACEMENT
Tools Required: None
Parts Required: Two (2) ECHO 0.080 (2 mm) Nylon Trimmer Line
203 mm (8 in.) long
1. Shut engine off. Lay unit on the ground with head assembly up.
2. Remove old nylon line through center recess of head.
3. Thread new lines through outside holes (A) in housing until ends
meet in center of recess.
A
GRASS TRIMMER
OPERATOR'S MANUAL
11
FRONT (LOOP) HANDLE
NOTE
Front handle is pre-installed. Re-positioning and tightening is all
that is required.
1 . Position front handle (E) in comfortable operating position and
tighten wing nut (F). The cutting attachment should be 5cm- 7.5cm
(2 in. -3 in.) above the ground and as level as possible.
PRE - OPERATION
FUEL
Fuel Requirements
Gasoline - Use 89 Octane [ ] (mid grade or higher) gasoline known
to be good quality. Gasoline may contain up to 15% MTBE (methyl
tertiary-butyl ether). Gasohol containing methyl (wood) alcohol is NOT
approved.
Two Stroke Oil - A two-stroke engine oil meeting ISO-L-EGD (ISO/CD
13738) and J.A.S.O. FC Standards, must be used. Echo brand Premium
50:1 oil meets these standards. Engine problems due to inadequate
lubrication caused by failure to use an ISO-L-EGD and J.A.S.O. FC
certified oil, such as Echo Premium 50:1 Two-stroke Oil, will void the
two-stroke engine warranty. (Emission related parts only are covered
for two years, regardless of two-stroke oil used, per the statement listed
in the Emission Defect Warranty Explanation.)
IMPORTANT
Echo Premium 2-Stroke Oil may be mixed at 50:1 ratio for application in all Echo engines sold in the past regardless of ratio specified in those manuals.
Mixing Instructions
1 . Fill an approved fuel container with half of the required amount of
gasoline.
2 . Add 2-stroke oil to gasoline.
3 . Close container and shake to mix oil with gasoline.
4 . Add remaining gasoline and remix.
5 . Install fuel container cap and wipe any spilled fuel from container
and surrounding area.
R + M
2
E
F
Handling Fuel
W ARNING DANGER
Fuel is VERY flammable. Use extreme
care when mixing, storing or handling,
or serious personal injury may result.
• Use an approved fuel container.
• DO NOT smoke near fuel.
• DO NOT allow flames or sparks near
fuel.
• Fuel tanks/cans may be under
pressure. Always loosen fuel caps
slowly allowing pressure to equalize.
• NEVER refuel a unit when the engine
is HOT!
• NEVER refuel a unit with the engine
running.
• DO NOT fill fuel tanks indoors.
ALWAYS fill fuel tanks outdoors over
bare ground.
• Securely tighten fuel cap after
refueling.
• Inspect for fuel leakage. If fuel leakage
is found, do not start or operate unit
until leakage is repaired.
12
IMPORTANT
Spilled fuel is a leading cause of hydrocarbon emissions. Some
states may require the use of automatic fuel shut-off containers to
reduce fuel spillage. Contact your ECHO dealer for ordering
information.
After refueling
• Wipe any spilled fuel from the unit.
• Move at least 3 m (10 ft.) from refueling location before starting the
engine.
After use
• DO NOT store a unit with fuel in its tank. Leaks can occur.
Return unused fuel to an approved fuel storage container.
Storage
Fuel storage laws vary by locality. Contact
your local government for the laws affecting
your area. As a precaution, store fuel in an
approved, air tight container. Store in a well
ventilated, unoccupied building, away from
sparks and flames. Do not store fuel longer
than 30 days.
IMPORTANT
Stored fuel ages. Do not mix more fuel
than you expect to use in thirty (30)
days, ninety (90) days when a fuel
stabilizer is added.
IMPORTANT
Stored two-stroke fuel may separate.
ALWAYS shake fuel container
thoroughly before each use.
OPERATION
GRASS TRIMMER
OPERATOR'S MANUAL
13
STARTING
COLD ENGINE
W ARNING DANGER
• Never leave the ignition switch in the on position while the unit is
unattended.
• Never allow partial tension to remain in the starter, otherwise
serious personal injury may result.
W ARNING DANGER
Never attempt to disassemble this recoil starter otherwise serious
personal injury may result. See your Echo Dealer if the starter
handle will not operate using light pulling force.
NOTE
Energy is stored in the starter spring each time the handle/rope is
pulled. Generally two to six pulls, using light pulling forces, will
store enough energy to engage the starter and spin the engine. Do
not pull the rope out to end stop.
NOTE
Refer to the Grass Trimmer / Brush Cutter Safety Manual for proper
and safe trimming techniques.
1. Stop Switch
Move stop switch button (A) away from the STOP position.
2. Choke
Move choke (B) to “Cold Start” Position.
3. Primer
Pump primer bulb (C) until fuel will be visible and flows freely in the
clear fuel tank return line. Pump bulb an additional 4 or 5 times.
W ARNING DANGER
Inspect starting area for hazards such as rocks, glass, debris etc.
which could be thrown by the cutting attachment when starting.
Keep helpers and bystanders at least 15 m (50 ft.) from starting area,
otherwise serious personal injury may result.
A
C
B
14
4. Recoil Starter
Lay the unit on a flat clear area. Firmly grasp throttle grip with
left hand and fully depress throttle trigger to wide open position.
Gently pull recoil starter handle/rope (D) until engine fires or 2 to 3
engine engagements.
5. Choke
After engine fires or 2 to 3 engine engagements, move choke lever
to “Run” position. Hold throttle trigger fully depressed and pull
starter handle/rope until engine starts and runs. Release throttle
trigger and allow unit to warm up at idle for several minutes.
NOTE
If engine does not start with choke in “Run” position after 5 engine
engagements, repeat instructions.
6 . After engine warm up, gradually depress throttle trigger to increase
engine RPM to operating speed.
STARTING WARM ENGINE
D
W ARNING DANGER
The cutting attachment should not rotate at idle. If attachment
rotates, readjust carburetor according to "Carburetor Adjustment"
instructions in this manual or see your ECHO Dealer, otherwise
serious personal injury may result.
1. Stop Switch
Move stop switch button (A) away from the STOP position.
2. Recoil Starter
Lay the unit on a flat clear area and gently pull the recoil starter
handle (D) until engine fires.
NOTE
If engine does not start after 5 engine engagements, use Cold Start
Procedure.
A
D
STOPPING ENGINE
1. Throttle
Release throttle and allow engine to return to idle before shutting
engine off.
2. Stop Switch
Move stop switch button (A) to STOP position.
W ARNING DANGER
If engine does not stop when stop switch is moved to STOP
position, close choke - COLD START position - to stall engine.
Have your ECHO dealer repair stop switch before using trimmer
again.
GRASS TRIMMER
OPERATOR'S MANUAL
A
15
MAINTENANCE
Your ECHO trimmer is designed to provide many hours of trouble free service. Regular scheduled maintenance will help
your trimmer achieve that goal. If you are unsure or are not equipped with the necessary tools, you may want to take your
unit to an ECHO Service Dealer for maintenance. To help you decide whether you want to DO-IT-YOURSELF or have the
ECHO Dealer do it, each maintenance task has been graded. If the task is not listed see your Echo dealer for repairs.
SKILL LEVEL
Level 1 = Easy to do. Most required tools come with unit.
Level 2 = Moderate difficulty. Some specialized tools may be required.
Level 3 = Experience required. Specialized tools are required. ECHO recommends
that the unit be returned to your ECHO dealer for servicing.
ECHO offers REPOWERTM Maintenance Kits and Parts to make your maintenance job easier. Just below each task
heading are listed the various part numbers required for that task. See your ECHO dealer for these parts.
16
MAINTENANCE INTERVALS
metsyS/tnenopmoCerudecorPecnanetniaM
retliFriAecalpeR/tcepsnI
reniartSleuFecalpeR/tcepsnI
eniLleuFecalpeR/tcepsnI
roterubraCecalpeR/naelC/tcepsnI
metsySekohCecalpeR/naelC/tcepsnI
metsySgnilooCnaelC/tcepsnI
krapSrelffuM
rotserrA
xelF(tfahSevirD
)sledoMelbaC
epoRretratSnaelC/tcepsnI
royliaD
erofeB
esU
yrevE
leufeR
shtnoM3
09ro
sruoH
shtnoM6
072ro
sruoH
ylraeY
C/I*R
IR
II
C/I)1(R
C/I
C/I
naelC/tcepsnI
esaerG
C/I
)2(I
I
skaeLleuFriapeR/tcepsnI
gulPkrapSecalpeR/naelC
stloB/stuN/swercSecalpeR/nethgiT/tcepsnI
TNATROPMI
.ecnanetniam
ylppA)2(OHCE
®
II
C/I*R
I
naelC=C/ecalpeR=R/tcepsnI=I
deriuqerfoycneuqerfehtenimretedlliwecneirepxeruoydnaesulautcA.mumixameranwohsslavretniemiT
sishtnom6yrevegninaelc,esuremusnoCroF.ylraeyesulaicremmocrofderiuqereblliwtnemecalpeR)1(
.stiKdliubeRsedulcnigninaelC.deriuqer
MT
EBUL
.esufosruoh52yreve
.noitcepsnignirudraewroegamadfognidnifehtnodesaberaecalperotsnoitadnemmocerllA*
AIR FILTER
Level 1.
Tools required: Cleaning brush, 25 or 50 mm (1 or 2 in.) medium bristle
paint brush.
GRASS TRIMMER
OPERATOR'S MANUAL
17
Parts required: 90008 REPOWER
1. Close choke (Cold Start Position). This prevents dirt from entering the
carburetor throat when the air filter is removed. Brush accumulated dirt
from the air cleaner area.
2. Remove the air cleaner cover. Clean and inspect the element for
damage. If element is fuel soaked and very dirty, replace.
3. If element can be cleaned and reused, be certain it:
-still fits the cavity in the air cleaner cover.
-is installed with the original side out.
NOTE
Carburetor adjustment may be needed after air filter cleaning/
replacement. See Carburetor Adjustment Section.
TM
AIR & FUEL FILTER KIT.
FUEL FILTER
Level 1.
Tools required: Fuel line hook, 200-250 mm ( 8-10 in.) length of wire
with one end bent into a hook. Clean rag, funnel, and
an approved fuel container.
Parts required: 90008 REPOWERTM AIR & FUEL FILTER KIT
W ARNING DANGER
Fuel is VERY flammable. Use extreme care when mixing, storing or
handling.
1 . Use a clean rag to remove loose dirt from around fuel cap and
empty fuel tank.
2 . Use the “fuel line hook” to pull the fuel line and filter from the tank.
3 . Remove the filter from the line and install the new filter.
18
SPARK PLUG
Level 2.
Tools Required: Spark Plug socket wrench and screw driver, Feeler
gauge. Preferably a wire gauge.
Parts Required: 90064 REPOWERTM Tune-Up Kit
1 . Remove spark plug and check for fouling, worn and rounded center
electrode.
2 . Clean the plug or replace with a new one. DO NOT sand blast to
clean. Remaining sand will damage engine.
3. Adjust spark plug gap by bending outer electrode.
4 . Tighten spark plug to 145-155 kg/cm (125-135 in. lb.).
COOLING SYSTEMS CLEANING
Level 2.
Tools required: Cross Head Screwdriver, 3 mm Hex Wrench, Cleaning
Brush, 25-50 mm (1-2 in.) medium bristle paint brush.
Parts Required: None.
IMPORTANT
To maintain proper engine operating temperatures, cooling air must
pass freely through the cylinder fin area. This flow of air carries
combustion heat away from the engine.
0.65 mm
(0.026 in.)
Overheating and engine seizure can occur when:
- Air intakes are blocked, preventing cooling air from reaching the
cylinder.
- Dust and grass build up on the outside of the cylinder. This build up
insulates the engine and prevents the heat from leaving.
Removal of cooling passage blockages or cleaning of cooling fins is
considered “Normal Maintenance”. Any failure attributed to lack of
maintenance is not warranted.
1 . Remove spark plug lead and throttle linkage end from the carbure-
tor swivel.
2. Remove the four screws that retain the cover. Two at the top of the
Recoil Starter, two on either side of the front. Lift the cover from the
engine and lay to the front of the trimmer.
NOTE
The throttle linkage remains assembled to the cover and the spark
plug lead and grommet remain installed.
IMPORTANT
DO NOT use a metal scraper to remove dirt from the cylinder fins.
3 . Use the brush to remove dirt from the cylinder fins.
4 . Remove grass and leaves from the grid between the starter and fuel
tank.
GRASS TRIMMER
OPERATOR'S MANUAL
19
5 . When installing the cover, be certain the tab of the metal deflector
shield is in the slot of the cover.
EXHAUST SYSTEM
Spark Arrestor Screen
Level 2.
Tools Required: Cross Head Screwdriver. Soft metal brush.
Parts Required: Screen P/N 14586240630, Gasket Lid P/N 14586642031
1 . Remove engine cover, see "Cooling System Cleaning" pages 18
and 19 for step by step instructions.
2 . Remove screen cover (A), holder (B) and gasket (C) from muffler
body.
3 . Clean carbon deposits from screen (D) and muffler components.
4 . Replace screen if it is cracked, plugged or has holes burned
through.
5. Assemble components in reverse order.
C
D
B
A
20
CARBURETOR ADJUSTMENT
Engine Break-In
New engines must be operated a minimum duration of two tanks of fuel
break-in before carburetor adjustments can be made. During the break-in
period your engine performance will increase and exhaust emissions will
stabilize. Idle speed can be adjusted as required.
High Altitude Adjustment
High altitude adjustment is not required for proper operation of this
engine.
Level 2.
Tools required: Screwdriver, Tachometer (ECHO P/N 99051130017).
Parts required: None.
NOTE
Every unit is run at the factory and the carburetor is set in compliance with emission regulations. In addition, the carburetor is
equipped with a HI needle adjustment limiter that prevents settings
outside acceptable limits.
1 . Before adjusting the carburetor, clean or replace the air filter and
spark arrester screen.
2 . Trimmer line must be extended to the cut-off knife.
3. Start engine and run for several minutes to reach operating
temperature.
4 . Stop engine. Turn HI speed needle (A) CCW (counter clockwise) to
stop.
5 . Idle Speed Adjustment.
• Start engine and turn “idle” speed adjustment screw (B) CW
until the blades begin to turn, then turn the screw CCW until
blades stop turning. Turn screw CCW an additional 1/4 turn.
6 . Accelerate to full throttle for 2-3 seconds to clear excess fuel from
engine then return to idle. Accelerate to full throttle to check for
smooth transition from idle to full throttle. If engine stops or stalls
after full warm up return the unit to your authorized ECHO dealer
for repair.
7 . Check HI speed RPM at W.O.T. (Wide Open Throttle). HI speed
RPM should be set to specifications found on page 9 "Specifications" of this manual.
8 . Check idle speed and reset if necessary. If a tachometer is available,
idle speed should be set to the specification found on page 9
"Specifications" of this manual.
A
B
W ARNING DANGER
When carburetor adjustment is completed, the cutting attachment
should not turn at idle, otherwise serious personal injury may
result.
LUBRICA TION
Level 1.
Tools Required: 8mm Open End Wrench, Screwdriver, Clean Rag.
Parts Required: ECHO® LUBETM 8 oz. (P/N 91014) or
Lithium Base Grease.
1 . Remove plastic shield.
GRASS TRIMMER
OPERATOR'S MANUAL
21
2. Loosen bearing housing locating screw (A), at the top of the
housing, loosen mounting screw (B) and remove gear case from
drive housing.
3 . Pull the flexible drive shaft (C) from the drive housing, wipe clean
and recoat with a thin coating [1/2 oz. (15 ml)] of grease.
4 . Slide the flexible drive shaft back in the drive housing being careful
not to get dirt on the flexible drive shaft.
5. Install the bearing housing and shield.
B
A
22
TROUBLESHOOTING
melborPkcehCsutatSesuaCydemeR
TRAHCGNITOOHSELBUORTMELBORPENIGNE
taleuF
roterubrac
rednilyctaleuFrednilyctaleufoNroterubraCrelaedohcEruoyeeS
enignE
-sknarc
/drahstrats
t'nseod
trats
,snurenignE
roseidtub
tonseod
etarelecca
ylreporp
dnetakrapS
eriwgulpfo
gulptakrapSkrapsoNtcerrocnipagkrapS
retlifriAytridretlifriAraewlamroNecalperronaelC
retlifleuFytridretlifleuFseudiser/stnanimatnoCni
tnevleuFdeggulptnevleuFniseudiser/stnanimatnoC
gulPkrapSnrow/ytridgulPraewlamroNecalperrotsujdadnanaelC
roterubraCtnemtsujdareporpmInoitarbiVtsujdA
roterubractaleufoNdeggolcreniartsleuF
deggolcenilleuF
roterubraC
leufhtiwtewrelffuMhcirooterutxiMleuFekohcnepO
krapsoNffohctiwspotS
melborplacirtcelE
hctiwskcolretnI
leufhtiwdeluoF
evitcefedgulP
leuf
leuf
ecalperronaelC
ecalperronaelC
relaedohcEruoyeeS
retlifriaecalper/naelC
roterubractsujdA
relaedohcEruoyeeS
NOothctiwsnruT
relaedohcEruoyeeS
relaedohcEruoyeeS
).ni620.0(mm56.ottsujdA
nobrachtiwderevoC
ecalpeR
ecalperronaelC
ecalperronaelC
gulpecalpeR
ecalperronaelC
metsySgnilooCmetsysgnilooC
deggulp/ytrid
rotserrAkrapS
neercS
seodenignE
ton
knarc
A/NA/NmelborpenignelanretnIrelaedohcEruoyeeS
rotserrakrapS
deggulpneercs
raewlamroNecalpeR
ninoitarepodednetxE
snoitacolytsud/ytrid
naelC
W ARNING DANGER
Fuel vapors are extremely flammable and may cause fire and/or explosion. Never test for ignition spark near an open
spark plug opening, otherwise serious personal injury may result.
GRASS TRIMMER
OPERATOR'S MANUAL
STORAGE
Long Term Storage (over 30 days)
W ARNING DANGER
During operation the muffler or catalytic muffler and surrounding cover become hot. Always keep exhaust area clear
of flammable debris during transportation or when storing, otherwise serious property damage or personal injury may
result.
Do not store your unit for a prolonged period of time (30 days or longer) without performing protective storage maintenance which includes the following:
1 . Store unit in a dry, dust free place, out of the reach of children.
23
W ARNING DANGER
Do not store in enclosure where fuel fumes may accumulate or reach an open flame or spark.
2. Place the stop switch (A) in the "OFF" position.
3 . Remove accumulation of grease, oil, dirt and debris
from exterior of unit.
4 . Perform all periodic lubrication and services that are
required.
5. Tighten all the screws and nuts.
6. Drain the fuel tank completely and pull the recoil
starter handle several times to remove fuel from the
carburetor.
7 . Remove the spark plug and pour 7 cc (1/4 oz.) (1/2
tablespoon) of fresh, clean, two-stroke engine oil into
the cylinder through the spark plug hole.
A.Place a clean cloth over the spark plug hole.
B . Pull the recoil starter handle 2-3 times to distribute
the oil inside the engine.
8. Install the spark plug (do not connect spark plug
cable).
IMPORTANT
Do not store the unit with tension remaining on the
starter spring.
SERVICING INFORMATION
P ARTS
Genuine ECHO Parts and ECHO REPOWER™ Parts and Assemblies for
your ECHO products are available only from an Authorized ECHO
Dealer. When you do need to buy parts always have the Model
Number, Type and Serial Number of the unit with you. You can find
these numbers on the engine housing. For future reference, write them
in the space provided below.
Model No. _____________ Type _________SN. ______________
SERVICE
Service of this product during the warranty period must be performed
by an Authorized ECHO Service Dealer. For the name and address of
the Authorized ECHO Service Dealer nearest you, ask your retailer or
call: 1-800-432-ECHO (3246). Dealer information is also available on our
Web Site. When presenting your unit for Warranty service/repairs,
proof of purchase is required.
www.echo-usa.com
DEALER?
Call
1-800-432-ECHO
or
ECHO CONSUMER PRODUCT SUPPORT
If you require assistance or have questions concerning the application,
operation or maintenance of this product you may call the ECHO
Consumer Product Support Department at 1-800-673-1558 from 8:30 am
to 4:30 pm (Central Standard Time) Monday through Friday. Before
calling, please know the model and serial number of your unit to help
your Consumer Product Support Representative.
CONSUMER PRODUCT
SUPPORT
1-800-673-1558
8:30 - 4:30 Mon - Fri C.S.T.
WARRANTY REGISTRATION
You may register your Echo equipment using the warranty registration
card or register on-line at www.echo-usa.com. Registering provides a
direct link between you and ECHO if we find it necessary to contact
you.
ADDITIONAL OR REPLACEMENT MANUALS
Safety Manuals in English/Spanish or English/French are available, free of charge, from your ECHO dealer or at
www.echo-usa.com.
Operator's and Parts Manuals are available by:
• Downloading free from www.echo-usa.com
• Purchasing from your Echo Dealer.
• Sending a check or money order for $2.00 per Parts Catalog or $1.50 per Operator's Manual made payable to ECHO,
INCORPORATED. State on a sheet of paper the model number and serial number of the ECHO unit you have, part
number of the manual (if known), your name and address and mail to address below.
Safety Videos are available from your Echo dealer. A $5.00 shipping charge will be required for each video.
Available Parts Catalog
GT-2000EZR S/N 03001001 & Up Part Number 99922203363
ECHO, INCORPORATED
400 OAKWOOD ROAD
LAKE ZURICH, IL 60047-1564
www.echo-usa.com
DESCRIPTION Page 7
CONTENTS
____ 1 - Trimmer Assembly
____ - Power Head
____ - Drive Shaft Assembly
____ 1 - Plastic Bag (Co-Pack)
____ - Rapid Loader 2-line Head
____ - Operator's Manual
EMISSION CONTROL
IMPORTANT ENGINE INFORMATION
ENGINE FAMIL Y : 2EHXS.0214RA DISPLACEMENT : 21.2cc
EMISSION COMPLIANCE PERIOD : 300 HRS.
THIS ENGINE MEETS U.S. EPA PHASE 2 EMISSION
REGULATIONS FOR SMALL NONROAD ENGINES. REFER
TO OWNER'S MANUAL FOR MAINTENANCE SPECIFICATIONS AND ADJUSTMENTS.
SUPPLEMENT TO OPERATOR'S MANUAL
PART NUMBER X7702273900 (X770000370)
FOR MODEL: GT-2000EZR S/N 03001001 & UP
Please use this Operator Manual Supplement when
assembling and maintaining your GT-2000EZR.
____ - Safety Manual
____ - Shield Assembly
____ - Hardware Bag
____ -Line Head Mount
____ -1, 3/8-24 Locknut
____ -1, Small Washer
The 300 hour emission durability compliance period is the time span selected by
the manufacturer certifying the engine emissions output meets applicable
California and/or U.S. EPA emissions regulations, provided that approved
maintenance procedures are followed as listed in the Maintenance Section of
this manual.
____ -1, Large Washer
____ -12, 8 in. X .080 Pre-cut Nylon Line
____ - Locking Tool
____ - Warranty Card & Limited Warranty
____ - Safety Glasses
____ - Oil 2 Stroke
PRODUCT EMISSION DURABILITY
ASSEMBLY - Page 10
PLASTIC SHIELD
Tools Required: None
1 . Remove wing nut (C), washer (B), and bolt (A).
2. Snap the shield over the bearing housing.
3 . Install bolt (A), washer (B) and wing nut (C).
NYLON LINE HEAD
Tools Required: Head Locking Tool, 9/16 in. Socket
Parts Required: Rapid Loader
1 . Remove plastic threaded shaft sleeve from PTO shaft.
2 . Align locating hole in upper plate with hole in bearing housing and insert 1/8 in.
diameter locking tool (A).
3 . Place large washer then line head on threaded shaft followed by small metal washer
and locknut.
TM
Head.
A
4. Tighten locknut securely.
IMPORTANT
Remember to remove the locking tool.
SUP22203524
99922203524
12/01
1
Please use this Operator Manual Supplement
when maintaining your GT-2000EZR/GT-201EZR.
SUPPLEMENT TO OPERATOR'S MANUAL
FOR MODELS: GT-201EZR S/N 02001001- 02999999
PART NUMBER X7702274001 (X770000381)
FOR MODELS: GT-2000EZR S/N 03001001- 03999999
PART NUMBER X7702273900 (X770000370)
MAINTENANCE - PAGE 18
COOLING SYSTEMS CLEANING
1 . Remove one (1) screw (A) from Top Guard and remove guard.
2 . Disconnect spark plug lead (B) from spark plug.
3 . Remove spark plug lead grommet from top of engine cover.
4 . Remove throttle linkage end (C) from the carburetor swivel.
5 . Release stored energy in EZR Starter power spring by removing
spark plug.
6 . Remove three (3) screws (D) from EZR Starter Assembly and
remove EZR Starter.
NOTE
DO NOT disassemble the EZR Starter Assembly.
7 . Remove the four screws that retain the engine cover. Two at the
inside top of the EZR mounting plate (E), two on either side of the
front (F).
B
C
A
D
8 . Disengage the heat deflector tabs (G) under the muffler from the
slots in the engine/muffler cover.
SUP22203562
E
G
F
99922203562
04/02
9 . Lift the cover from the engine and lay to the front of the trimmer.
NOTE
The throttle linkage remains assembled to the cover.
10. Reinstall spark plug to prevent dirt and debris from entering engine.
11. Use a brush to remove dirt from the cylinder fins.
IMPORTANT
DO NOT use a metal scraper to remove dirt from the cylinder fins.
12. Remove grass and leaves from the grid between the starter and fuel
tank.
13. Reassemble parts in reverse order of removal. When installing the
cover, be certain:
• the tabs of the deflector shield (A) are in the slots of the cover
• the fuel check valve (B) is positioned in the cover
• the spark plug (C) is tightened securely
• the ignition wire (D) is not pinched
C
B
A
D
14. When installing EZR starter housing to EZR mounting body, be sure
that EZR drive starter cam engages the starter pawl correctly.
2
Loading...