
TECHNICAL SPECIFICATION
SIDE ELEVATIONFRONT ELEVATION
Fixing
locations
(4)
Water
entry point
303
64
50.8
159
35
Basin/worktop thickness
Max 57 Min 3.5
372
Fixing
locations
(4)
286
52.2
Distance from
the aerator to the
end of the tap
Max 835.5 / Min 631.5
Fixing
locations
(4)
142
FLOOR
Tap dimensions
WD04 Height 159 mm Width 303 mm Depth 286 mm
Motor bucket dimensions
WD04 Height 266 mm Width 142 mm Depth 189 mm
For further information please contact Dyson.
Tel: 1800 426 337
www.dyson.com.au/hand-dryers
aucommercial@dyson.com
266
Rear cable
entry point
Fixing
locations
(4)
All dimensions shown
in mm (+/-5 mm)
Minimum clearance
Z 100 mm clearance from floor
189

TECHNICAL SPECIFICATION
FRONT ELEVATION SIDE ELEVATION
286
Fixing
locations
(4)
Water
entry point
50.8
303
309
Distance from
the aerator to the
end of the tap
35
Basin/worktop thickness
Max 57 Min 3.5
372
Fixing
locations
(4)
52.2
Max 835.5 / Min 631.5
Fixing
locations
(4)
142
FLOOR
Tap dimensions
WD05 Height 309 mm Width 303 mm Depth 286 mm
Motor bucket dimensions
WD05 Height 266 mm Width 142 mm Depth 189 mm
266
Rear cable
entry point
Fixing
locations
(4)
All dimensions shown
in mm (+/-5 mm)
Minimum clearance
Z 100 mm clearance from floor
189

60
<50
52.2
31271
260
40
272
95.4
50.8
303
272
34
342
94 32 42
370
343
623 194
196
60
771
52.2
260
40
272
95.4
50.8
303
272
34
342
94 32 42
370
TECHNICAL SPECIFICATION
SIDE ELEVATION
Distance from
the aerator to the
end of the tap
Water
entry
point
Cable
entry
point
FRONT ELEVATION
5 mm
diameter hole
Fixing
locations
(4)
FLOOR
Tap dimensions
WD06 Length 312 mm Width 303 mm
Motor bucket dimensions
WD06 Height 266 mm Width 142 mm Depth 189 mm
Minimum clearance
Suggested installation height 955mm from finished floor to centre of tap, depending
on height of basin. Check installation guide for further details.

TECHNICAL SPECIFICATION
WD06 Wall installation
The Dyson Airblade Wash+Dry hand dryer is designed
so that the motor unit is located behind the stud wall within
a metal enclosure which is supplied with the Dyson Airblade
Wash+Dry hand dr yer (Fig.1). The vertical wall studs must
be constructed so as to allow the metal enclosure to be fitted
between them (Fig.2). One of the horizontal wall studs must be
fitted a) so it holds the main weight of the metal duct and the
unit, and b) so it is in the correct position for the tap stem.
For complete instructions, please refer to the printed
installation guide supplied with the machine.
It’s also available online at
www.dyson.com.au/hand-dryers/useful-documents
Fi g.1
Fig.2
Fig.3 Fig.4
Install
plasterboard.
Install Dyson
Airblade
Wash+Dry
hand dryer.

TECHNICAL SPECIFICATION
Electrical
Input voltage/Frequency: 200-240V 50-60Hz
Motor specification: 1000W digital brushless motor
Operating temperature range: 0°-40°C
Heater type: None
Standby power consumption: Less than 0.5 W
Construction
Tap construction: Stainless steel (brushed)
Under counter motor assembly construction: Moulded ABS (main unit)
Exterior screw type: Torx T15
Water ingress protection to IP35
Filter
HEPA filter (glass fibre and fleece prelayer)
Captures 99.95% of particles the size of bacteria from the washroom air
1
Operation
Touch-free infra-red activation
Hand dry time measurement: 14 seconds
Operation lock-out period: 30 seconds
Airspeed at apertures: 549 km/h
Maximum altitude: 2,000 metres
Water operation
Water flow rate: 1.9 l/min normal fitted aerator.
4 l/min with low flow aerator supplied with product.
Water temperature control: Thermostatic mixer recommended (not supplied)
Water pressure required: 100-800 kPa
Equipped with automatic duty flush –
every 24 hours for 60 seconds after the last use.
Basin specification
The Dyson Airblade Wash+Dry hand dryer is compatible with most
basin types. Ensure plugs are not installed in the basins and avoid
inserts with embedded plugs (e.g. ones that swivel or elevate).
Using a specially designed test method, Dyson engineers evaluated
the user experience of a wide range of basin types when used with
the Dyson Airblade Wash+Dry hand dryer. For further details on our
recommended basins, please contact Dyson.
We recommend avoiding basins with the following geometric characteristics;
Flat bases immediately surrounding the drain hole.
(nominally within a 60 mm radius).
Sloping back and front wall transitions in relation to the base of the basin.
See our pre-installation guide for further details:
www.dyson.com.au/hand-dryers/useful-documents
Basin dimensions:
All basin measurements are internal unless stated otherwise.
Minimum width of basin: 350 mm, Front to back – Minimum: 300 mm
Minimum depth of basin: 100 mm
Maximum depth of basin for WD05 only: 200 mm
(External measurement of vessel basin)
Basin materials: Basins with highly polished surfaces should be avoided,
e.g. reflective chrome. Porcelain or brushed metal is ideal. When multiple taps
are installed side-by-side, tap centres should be a minimum
of 580 mm apart.
Standard guarantee
5 year par ts, 5 year labour.
Product range
WD04 Short WD05 Tall WD06 Wall
Logistics
Net weight: WD04 4.26 kg; WD05 4.54 kg; WD06 9.51 kg
Packaged weight: WD04 6.76 kg; WD05 7.38 kg; WD06 13.65 kg
Packaged dimensions: WD04 H303 × W284 × D291 mm
WD05 H434 × W275 × D288 mm; WD06 H610 × W375 × D302 mm
1
HEPA filt er tested to EN1822-5, by a n independent t esting labor atory, under pre scribed tes t conditions.

Further documents are
available online to download.
Pre-installation guide.
Installation guide.
Dyson Airblade Wash+Dry
hand dryer brochure.
Cleaning guide.
CAD drawings.
Installation videos.
The Carb on label is a tra demark of th e Carbon Trust.
HACCP International non-food certification mark is the registered trademark of HACCP International.
HACCP I nternatio nal have cer tified D yson produc ts based o n their recom mended ins tallation a nd
operat ing conditio ns. Licens ed by Dyson. Q uiet Mark is a t rade mark of th e Noise Aba tement So ciety.
For further information please contact Dyson.
Tel: 1800 426 337
www.dyson.com.au/hand-dryers
aucommercial@dyson.com