Page 1
ASSEMBLY INSTRUCTIONS
DX-WD1335
Wood TV Stand
Tools needed........................................... 2
Parts ........................................................... 3
Hardware.................................................. 4
Assembly instructions......................... 5
Page 2
2 DX-WD1335
Safety information and specifications
CAUTION: This stand’s wood surface is
intended only for use with a product not
weighing more than 50 lbs (22.7 kg) and having a
with no more than one-inch overhang on each side on the
top shelf. Using with other products, including products that
weigh more than the maximum weight allowed, may result
in instability, which may cause possible injury.
Model #: DX-WD1335
Distributed by Best Buy Purchasing, LLC
width that will permit it to sit evenly on the stand
)
m
c
0
4
(
"
5
7
.
5
1
3
5
.
2
5
5
0
l
b
s
(
2
2
.
6
9
k
2
5
l
b
s
(
1
1
.
3
4
k
g
)
Weight capacity (top shelf): 50 lbs (22.7 kg)
Weight capacity (lower shelf): 25 lbs (11.34 kg.)
Overall dimensions (W × H × D):
36 × 21.75 × 15.75 in. (91.44 × 55.25 × 40 cm)
Top shelf (W × D): 35.25 × 12.75 in. (89.54 × 32.39 cm)
Usable lower shelf (W × H × D):
30.25 × 5.5 × 12.75 in. (76.84 × 13.97 × 32.39 cm)
3
6
"
(
9
1
.
4
4
c
m
"
(
8
9
.
5
4
c
m
)
g
)
)
)
m
c
9
3
.
2
3
(
"
5
7
.
2
1
Tools needed
21.75" (55.25 cm)
No. 2 Phillips screwdriver
Need help? Call 800-305-2204
Page 3
DX-WD
1335
Parts
Package contents: parts
3
Note: Some parts have a label on the edge to help distinguish similar parts from each other. Use this illustration to help
identify similar parts.
Item Description Qty.
A Right end 1
B Left end 1
C To p 1
D Lower shelf 1
E Back 1
Need help? Call 800-305-2204
Item Description Qty.
F Right front leg 1
G Left front leg 1
H Rear leg 2
I Skirt 1
J Stop molding 1
Page 4
4 DX-WD1335
Hardware
Package contents: hardware
Make sure that you have all the hardware necessary to assemble your new TV stand:
Label Hardware Qty.
K2
L13
M6
N7
O2
P2
Twist-lock® fastener
Hidden cam
Cam dowel
Cam screw
Angle bracket
Wood dowel
Label Hardware Qty.
Q6
R1
S1
T11
Black 1-7/8" flat head screw
U4
Cam cover
Glue
Warning
label
Black 9/16"
large head
screw
1234in
10 20 30 40 50 6 0 70 80 9 0 1 00mm
Need help? Call 800-305-2204
Page 5
DX-WD
1335
Assembly instructions
Step 1:
Caution: Assemble your TV stand on carpeted floor or on the empty carton to avoid scratching your stand or
the floor.
Push a Twist-lock® fastener (K) into each of the two the holes in the back (E).
Important: Do not tighten the Twist-lock® fasteners in this
step.
5
You’ll need:
K (2)
Need help? Call 800-305-2204
Page 6
6 DX-WD1335
Step 2:
Push 13 hidden cams (L) into the ends (A and B), top (C), and back (E). Make sure that the arrows on the hidden
1
cams (L) are pointing toward the closest edge.
2 Insert the metal end of a cam dowel (M) into each hidden cam, except in the top (C) and short edge of each
end (A and B).
Important: Do not tighten the hidden cams in this step.
Do not insert cam
dowels into this part.
Arrow
You’ll need:
Do not insert
cam dowels
into these
edges.
Arrow
Arrow
Arrow
Insert the metal
end of the cam
dowel into the
hidden cam.
L (13) M (6)
Need help? Call 800-305-2204
Page 7
DX-WD
1335
Step 3:
Screw seven cam screws (N) into the front legs (F and G) and stop molding (J).
7
You’ll need:
N (7)
Need help? Call 800-305-2204
Page 8
8 DX-WD1335
Tightening hidden cams:
In the remaining steps, use these illustrations for instructions on tightening hidden cams.
Warning: Risk of damage or injury. Hidden cams must be completely tightened. Hidden cams that are
not completely tightened will loosen, and parts may separate.
Arrow
Make sure that you turn the
hidden cam a minimum of
190° to a maximum of 210°.
Note the position of the arrow
on the hidden cam.
Arrow
210°
In the illustration below,
the hidden cam has not
been tightened enough.
You’ll need:
190°
Phillips screwdriver
Need help? Call 800-305-2204
Page 9
DX-WD
1335
Step 4:
Align the stop molding (J) with the top (C), then tighten the three hidden cams.
S
u
r
f
a
c
e
w
i
t
h
h
i
d
d
e
n
c
a
m
s
S
u
r
f
a
c
e
w
i
t
h
h
o
l
e
s
9
You’ll need:
Phillips screwdriver
Need help? Call 800-305-2204
Page 10
10 DX-WD1335
Step 5:
Align the ends (A and B) with the back (E), then tighten the two hidden cams.
Edges with hidden cams
Edge with Twist-lock® fasteners
s
m
a
c
n
e
d
d
i
h
h
t
i
w
e
c
a
f
r
u
S
S
u
r
f
a
c
e
w
i
t
h
f
a
T
s
w
t
e
i
n
s
t
e
-
l
r
o
s
c
k
®
You’ll need:
Edges with hidden cams
s
m
ca
n
e
d
d
i
h
t
u
o
h
t
i
w
ce
a
f
r
u
S
Phillips screwdriver
Need help? Call 800-305-2204
Page 11
DX-WD
1335
Step 6:
Caution: Check the parts carefully before assembling. Disassembly of glued parts is extremely difficult.
1 Fill the holes in the stop molding (J) 1/4 to 1/2 full with glue (R), then insert the wood dowels (P) into the holes.
Wipe away the excess glue.
2 Drop a few beads of glue (R) into the holes in the ends (A and B).
3 Align the ends (A and B) and the back (E) with the top (C) and the stop molding (J). Make sure that the dowels,
Twist-lock
Twist-lock® fasteners.
Note: Wipe away the excess glue with a damp cloth.
To use a Twist-lock®
fastener:
1 Insert the dowel end
of the fastener into the
hole of the adjoining
part.
Note: The dowel end of
2 Tighten the fastener
with a Phillips
screwdriver as tight as
possible.
® fasteners, and cam dowels align with the correct holes, then tighten the four hidden cams and two
the fastener must
remain fully inserted
in the hole of the
adjoining part while
locking the fastener.
Dowel end
T
w
i
Fill the holes 1/4 to
1/2 full with glue.
S
u
r
f
a
s
t
c
-
e
l
o
w
c
k
i
t
®
f
a
s
t
e
h
n
®
e
r
11
Maximum: 210°
Minimum:
190°
S
u
Arrow
You’ll need:
Need help? Call 800-305-2204
r
f
a
c
e
w
i
t
h
h
i
d
d
e
n
c
a
m
s
Phillips screwdriverP (2) R (1)
Page 12
12 DX-WD1335
Step 7:
1
Attach two angle brackets (O) to the stop molding (J) using two black 9/16" large head screws (U).
2 Fasten the skirt (I) to the stop molding (J) using two black 9/16" large head screws (U).
Note: There are no pre-drilled holes in the skirt. The screws tighten into the groove.
You’ll need:
Phillips screwdriverO (2) U (4)
Need help? Call 800-305-2204
Page 13
DX-WD
Step 8:
1
Align right front leg (F) with the right end (A) and the left front leg (G) with the left end (B), then tighten the four
hidden cams (L).
2 Attach the rear legs (H) to the ends (A and B) using four black 1-7/8" flat head screws (T).
Important: Make sure that the rear legs (H) angle out and away from the stand.
1335
13
You’ll need:
Phillips screwdriverT (4)
Need help? Call 800-305-2204
Page 14
14 DX-WD1335
Step 9:
Fasten the lower shelf (D) to the ends (A and B) and back (E) using seven black 1-7/8" flat head screws (T).
Long finished edge
U
n
f
i
n
i
s
h
e
d
s
u
r
f
a
c
e
You’ll need:
Phillips screwdriverT (7)
Need help? Call 800-305-2204
Page 15
DX-WD
1335
Step 10:
1
Carefully turn your TV stand upright.
2 Apply the warning label (S) to the top (C) so that the TV will hide the label. Peel off the backing and apply the
label as shown in the diagram.
Note: This is a permanent label intended to last for the life of the product. After you apply the label, do not try to
remove it.
3 Push a cam cover (Q) onto each visible hidden cam.
15
For customer service, call: 800-305-2204 (U.S./Canada markets)
Need help? Call 800-305-2204
You’ll need:
Q (6)
S (1)
Page 16
Certificate of Conformity
1. This certificate applies to the Sauder Woodworking Product
identified by this instruction booklet.
2. This certificate applies to the compliance of this product with
the CPSC Ban on Lead-Containing Paint (16 CFR 1303).
3. This product was manufactured by:
Sauder Woodworking Company
502 Middle Street
Archbold, Ohio 43502
(419) 446-2711
4. Date of Manufacture: _______________
Lot number: 345399
www.dynexproducts.com (800) 305-2204
Distributed by Best Buy Purchasing, LLC
7601 Penn Ave. South, Richfield, MN 55423 U.S.A.
© 2012 BBY Solutions, Inc.
All rights reserved.
DYNEX is a trademark of BBY Solutions, Inc. Registered in some countries. All other products and
brand names are trademarks of their respective owners.
12-0625
ENGLISH
Loading...