Dynex DX-WD1239 User Manual

ASSEMBLY INSTRUCTIONS

DX-WD1239

TV Cart

Safety information and specifications ............2

Tools needed............................................................3

Package contents ................................................... 3

Assembly instructions...........................................5

2 DX-WD1239

Safety information and specifications

CAUTION:

This TV cart’s work surface is intended only for
use with a product not weighing more than 95

lbs. (43.09 kg) and having 42" wide flat-panel TV
dimensions that will permit it to sit evenly on your TV cart.
Using with other products, including products that weigh
more than the maximum weight allowed, may result in
instability, which may cause possible injury.

28.12" (71.45 cm)

Maximum weight: 95 lbs. (43.09 kg)
Maximum screen size: 42"
Weight capacity (top of TV cart): 95 lbs. (43 kg)
Weight capacity (middle shelf ): 25 lbs. (11 kg)
Weight capacity (lower shelf ): 30 lbs (13 kg)
Overall dimensions: W × H × D

28.12 x 18.75 × 14.88 inches (71.45 × 47.6 × 37.8 cm)
Top of T V cart: W × D

28.12 × 14.88 inches (71.45 × 37.8 cm)
Usable upper shelf (shelf in middle position) :W × H × D

17.81 × 6.31 × 13.56 inches (45.2 × 16 × 34.3 cm)
Usable lower shelf (shelf in middle position): W × H × D

17.81 × 6.38 × 15.5 inches (45.2 × 16.2 × 39.4 cm)

14.88" (35.25 cm)

Warnings

• Do not let children climb on your TV cart or play near it. Your TV cart may tip over causing the TV or cart to
injure someone.

• When placing items on the shelves or the top of the TV cart, load the bottom shelf first and work up to the top
of your TV cart.

• Do not overload the shelves. They may break.

• Do not move your TV cart with items on the top or shelves. Your TV cart may tip over and injure someone.
Before you move your TV cart, unload starting with the top of your TV cart and working to the bottom shelf.

18.75" (47.6cm)

Need help? Call 800-305-2204

DX-WD1239

Tools needed

3

No. 2 Phillips screwdriver

Caution: Do not
use an electric drill
or screwdriver

Package contents

Package contents: hardware

Make sure you have all the hardware necessary to assemble your new TV cart:

Label Hardware Qty.

I2 9

J2 9

K2

Hidden cam

Cam dowel

Swivel caster

Label Hardware Qty.

M8

N4

O1

Hammer

Metal pin

Rubber sleeve

Warning
label

L2

Non-swivel
caster

Using a screw that is too long will cause damage your TV cart. Before beginning assembly, separate each
type of screw. Carefully study the screw table below. You can use the ruler at the bottom of the screw
table to measure screws. Pay close attention to the color of each screw.

You may receive extra hardware with your TV cart.

Letter Description Qty. Letter Description Qty.

P6Q16

Black 1 7/8" (47.75 mm) flat head screw

Black 9/16" (14.22 mm) large
head screw

1234in

10 20 30 40 50 60 70 80 90 1 00mm

Need help? Call 800-305-2204

4 DX-WD1239

Package contents: parts

Note: All parts except for the stop molding (H) have a lettered sticker to make identifying parts easier.

Letter Description Qty. Letter Description Qty.

A Right end 1EBottom 1

B Left end 1FAdjustable shelf 1

C Upright 1GValance 1

D Top 1HStop molding 1

Need help? Call 800-305-2204

DX-WD1239

Assembly instructions

Step1:

Assemble your TV cart on a carpeted floor or on the empty carton to avoid scratching your TV cart or the
floor.

Push nine hidden cams (I2) into the ends (A and B), upright (C), and top (D), then insert the metal end of a
cam dowel (J2) into each hidden cam.

Do not tighten the hidden cams in this step.

5

You’ll need:

Arrow

J2 (9)I2 (9)

Need help? Call 800-305-2204

6 DX-WD1239

Step 2:

Insert two metal pins (M) into the two holes beside the hidden cam on the right end (A).
Repeat this step for the left end (B).

You’ll need:

M (4)

Need help? Call 800-305-2204

DX-WD1239

Tightening hidden cams

In the remaining steps, use these illustrations for instructions on tightening hidden cams.
Warning : Risk of damage or injury. Hidden cams must be completely tightened. Hidden cams that are not

completely tightened will loosen, and parts may separate.

Arrow

Make sure that you turn the
hidden cam a minimum of
190° to a maximum of 210°.
Note the position of the arrow
on the hidden cam.

Arrow

210°

7

In the illustration below,
the hidden cam has not
been tightened enough.

190°

You’ll need:

Phillips screwdriver

Need help? Call 800-305-2204

8 DX-WD1239

Step 3:

Fasten the stop molding (H) to the top (D). Use a Phillips screwdriver to tighten three hidden cams. See
“Tightening hidden cams” on page 7.

Unfinished
surface

Maximum210°

Minimum 190°

Arrow

You’ll need:

Phillips screwdriver

Need help? Call 800-305-2204

DX-WD1239

9

Step 4:

Fasten the left end (B) to the top (D). Use a Phillips screwdriver to tighten two hidden cams. See “Tightening
hidden cams” on page 7.

Finished
edge

Maximum 210°

Minimum 190°

Arrow

You’ll need:

Phillips screwdriver

Need help? Call 800-305-2204

10 DX-WD1239

Step 5:

Slide the valance (G) onto the two metal pins (M) in the left end (B).

Unfinished
surface

Finished
edge

Need help? Call 800-305-2204

DX-WD1239

11

Step 6:

Fasten the right end (A) to the top (D). Use a Phillips screwdriver to tighten two hidden cams. See “Tightening
hidden cams” on page 7.

Note: Make sure that the metal pins in the right end (A) insert into the holes in the valance (G).

Maximum 210°

Minimum 190°

Finished
edge

Arrow

You’ll need:

Phillips screwdriver

Need help? Call 800-305-2204

12 DX-WD1239

Step 7:

Fasten the upright (C) to the top (D). Use a Phillips screwdriver to tighten two hidden cams. See “Tightening
hidden cams” on page 7.

Fasten the bottom (E) to the ends (A and B) and upright (C). Use a Phillips screwdriver and six black 1 7/8" flat
head screws (P).

Screw holes

Unfinished
surface

Long finished edge

Finished edge

Maximum 210°

Arrow

You’ll need:

Phillips screwdriver

Minimum 190°

P (6)

Need help? Call 800-305-2204

DX-WD1239

13

Step 8:

Fasten the swivel casters (K) and the non-swivel casters (L) to the bottom (E). Use a Phillips screwdriver and
16 black 9/16" large head screws (Q) (four screws per caster).

The tabs on the
non-swivel casters (K)
must insert into these
holes.

You’ll need:

Phillips screwdriver Q (16)

Need help? Call 800-305-2204

14 DX-WD1239

Step 9:

Carefully stand your TV cart upright.
Push the rubber sleeves (N) on the metal pins (N), then insert the metal pins into the hole locations of your

choice in the right end (A) and upright (C). Set the adjustable shelf (F) onto the metal pins (M).
Apply the warning label (O) to the top (D). You should be able to read the label when the TV is removed from

your TV cart. When the TV is in place, it should hide the label. Peel off the backing and apply the label as
shown.

Caution: This is a permanent label intended to last for the life of the product. Once applied, do not try to
remove it. You may damage the finish on the top.

War ning: Never use this
furniture with a TV that is too
large or too heavy. Severe
injury or death can occur. The
TV and furniture will be
unstable and may tip.

• The TV must weigh less
than 95 lbs.

95 lbs
(43 kg)

• The base of the TV must
be able to sit completely
on this shelf.

25 lbs
(11 kg)

30 lbs
(13 kg)

You’ll need:

Metal pin
with
rubber
sleeve

N (4)M (4)

Need help? Call 800-305-2204

DX-WD1239

Still need help?

For customer service, call: 800-305-2204 (U.S./Canada markets)
Distributed by Best Buy Purchasing, LLC
7601 Penn Avenue South, Richfield, MN USA 55423-3645
© 2011 BBY Solutions, Inc.
All rights reserved. DYNEX is a trademark of BBY Solutions, Inc. Registered in some countries. All other

products and brand names are trademarks of their respective owners.

15

Need help? Call 800-305-2204

Certificate of Conformity

1. This certificate applies to the Sauder
Woodworking Product identified by this
instruction booklet.

2. This certificate applies to the compliance of this
product with the CPSC Ban on Lead-Containing
Paint (16 CFR 1303).

3. This product was manufactured by:
Sauder Woodworking Company
502 Middle Street
Archbold, Ohio 43502
[phone]

4. Date of Manufacture: ____________

Lot number: 346230

www.dynexproducts.com [phone]

Distributed by Best Buy Purchasing, LLC

7601 Penn Ave. South, Richfield, MN 55423 U.S.A.

© 2011 BBY Solutions, Inc.

All rights reserved.

DYNEX is a trademark of BBY Solutions, Inc. Registered in some countries. All other products and

brand names are trademarks of their respective owners.

12-0784
ENGLISH