Dynex DX-WD1201 User Manual

ASSEMBLY INSTRUCTIONS

DX-WD1201

Espresso TV Stand for 32" TVs

Safety information and specifications ............2

Tools needed............................................................3

Package contents ...................................................4

Assembly instructions...........................................6

2 DX-WD1201

Safety information and specifications

CAUTION:

This stand’s work surface is intended only for use
with a product not weighing more than 95 lbs.

(43.09 kg) and accommodates most 32"
flat-panel TVs with dimensions that will permit the TV to sit
evenly on the stand. Using with other products, including
products that weigh more than the maximum weight
allowed, may result in instability, which may cause possible
injury.

18" (45.72 cm)

Maximum weight: 95 lbs. (43.09 kg)
Maximum screen size: Most 32" flat-panel TVs
Weight capacity (top of stand): 95 lbs. (43 kg)
Weight capacity (top shelf): 35 lbs. (15 kg)
Weight capacity (middle shelf): 25 lbs. (11 kg)
Weight capacity (total lower shelf): 50 lbs (22 kg)
Overall dimensions: (W × H × D)

35.38 x 27.25 × 18 inches (89.86 × 69.21 × 45.72 cm)
Top of stand: (W × D) 35.38 × 18 inches (89.86 × 45.72 cm)
Usable top shelf: (W × H × D)
29 × 6.13 × 15.5 inches (73.66 × 15.57 × 39.37 cm)
Usable left game shelf: (W × H × D)

9.38 × 14.5 × 15.5 inches (23.82 × 36.83 × 39.37 cm)
Usable right middle shelf (in middle position): W × H × D

19.25 × 6.88 × 15.5 inches (48.89 × 17.47 × 39.37 cm)
Usable lower shelf (shelf in middle position): W × H × D

19.25 × 6.88 × 15.5 inches (48.89 × 17.47 × 39.37 cm)

35.38" (89.86 cm)

Warnings

• Do not let children climb on your stand or play near it. The stand may tip over causing the TV or stand to
injure someone.

• When placing items on the shelves or the top of the stand, load the bottom shelf first and work up to the top
of your stand.

• Do not overload the shelves. They may break.

• Do not move your stand with items on the top or shelves. Your stand may tip over and injure someone. Before
you move your stand, unload starting with the top of your stand and working to the bottom shelf.

• Do not push your stand to move it. With the help of a second person, lift your stand to move it.

27.25" (69.21 cm)

32.5" (85.55 cm)

15.75" (40 cm)

Need help? Call 800-305-2204

DX-WD1201

Tools needed

No. 2 Phillips screwdriver

3

Flatblade screwdriver

Caution: Do not
use an electric drill
or screwdriver

Hammer

Need help? Call 800-305-2204

4 DX-WD1201

Package contents

Package contents: hardware

Make sure you have all the hardware necessary to assemble your new TV stand:

Label Hardware Qty.

M17

N17

O3

P6

Hidden cam

Cam dowel

Angle
bracket

Metal pin

Label Hardware Qty.

T2

Black 1-7/8”flat
head screw

Label Hardware Qty.

Q4

R13

S1

Rubber
sleeve

Cam cover

Warning
label

U6

Black 9/16” large
head screw

V24

1234in

10 20 30 40 50 60 70 80 90 1 00mm

Nail

Need help? Call 800-305-2204

DX-WD1201

Package contents: parts

Note: All parts except for the back (G) have a lettered sticker to make identifying parts easier.

5

Letter Description Qty. Letter Description Qty.

Right end 1

A

Left end 1

B

Upright 1

C

Top 1

D

Bottom 1

E

Shelf 1

F

Back

G

Adjustable shelf

H

Stop molding

I

Top skirt

J

Bottom molding

K

End molding

W

1

1

1

1

1

2

Need help? Call 800-305-2204

6 DX-WD1201

Assembly instructions

Step1:

A hidden cam (M) has an arrow. When you insert the hidden cam, make sure that the arrow points toward the
hole in the side of the part you are inserting it into.

Assemble your stand on a carpeted floor or on the empty carton to avoid scratching your unit or the floor.
Push seventeen hidden cams (M) into the ends (A and B), top (D), bottom (E), and shelf (F). Then, insert a cam

dowel (N) into each hidden cam.

Do not tighten the hidden cams in this step.

You’ l l n e e d :

N (17)M (17)

Need help? Call 800-305-2204

DX-WD1201

Tightening hidden cams:

In the remaining steps, use these illustrations for instructions on tightening hidden cams.
Warning: Risk of damage or injury. Hidden cams must be completely tightened. Hidden Cams that are not

completely tightened will loosen, and parts may separate.

7

Arrow

In the illustration below,
the hidden cam has not
been tightened enough.

Make sure that you turn the
hidden cam 210°. Note the
position of the arrow on the
hidden cam.

Arrow

210°

You’ l l n e e d :

Flatblade screwdriver

Need help? Call 800-305-2204

8 DX-WD1201

Step 2:

Fasten the shelf (F) to the ends (A and B). Use a flatblade screwdriver to tighten four hidden cams (M). See
“Tightening hidden cams:” on page 7.

Insert two metal pins (P) into the upright (C), then insert the other ends of metal pins (P) into the holes in the
shelf (F).

Notched edge

Finished edge

Notched
edge

Surface with holes

210°

Arrow

You’ll need:

P (2)Flatblade screwdriver

Need help? Call 800-305-2204

DX-WD1201

9

Step 3:

Slide the bottom molding (K) onto the notched edge of the bottom (E).
Fasten the bottom (E) to the ends (A and B). Use a flatblade screwdriver to tighten four hidden cams (M). See

“Tightening hidden cams:” on page 7.
Fasten the bottom (E) to the upright (C). Use a Phillips screwdriver and two black 1-7/8" flat head screws (T).

fi

Surface
with
hidden
cams

Holes for screws

You’ll need:

US Patent #5,499,886

Arrow

210°

Flatblade screwdriver Phillips screwdriver

Need help? Call 800-305-2204

T (2)

10 DX-WD1201

Step 4:

Fasten three angle brackets (O) to the stop molding (I). Use a Phillips screwdriver and three black 9/16" large
head screws (U).

Fasten the stop molding (I) to the top (D). Use a flatblade screwdriver to tighten three hidden cams (M). See
“Tightening hidden cams:” on page 7.

Carefully turn your stand onto its top.
Fasten the ends (A and B) to the top (D). Use a flatblade screwdriver to tighten six hidden cams (M).

Arrow

210°

Notched edges

You’ll need:

Phillips screwdriver

Flatblade screwdriver

U (3)

O (3)

Need help? Call 800-305-2204

DX-WD1201

11

Step 5:

Slide the end moldings (W) onto the notched edges of the ends (A and B).
Fasten the top skirt (J) to the angle brackets (O) on the stop molding (I). Use a Phillips screwdriver and three

black 9/16" large head screws (U).

Note: There are no pre-drilled holes in the top skirt (J). The screws will tighten into the groove.

You’ll need:

Phillips screwdriver

Need help? Call 800-305-2204

U (3)

12 DX-WD1201

Step 6:

Carefully turn your stand over onto its front edges. Unfold the back (G) and lay it over your stand.
Make equal margins along the side and bottom edges of the back (G). Push on opposite corners of your stand

if needed to make it “square.”
Fasten the back (G) to your stand using the nails (V).

Note: Make sure that you tap nails into the holes that line up over the upright (C) and shelf (F).
Note: Perforations have been provided for access through the back (G). Carefully cut out the holes needed.

Caution: Do not

stand your stand
upright without the
back fastened. Your
stand may collapse.

These holes must line up over the
back edges on the upright (C) and
shelf (F).

Do not tap
nails in this
edge

You’ l l n e e d :

V (24)

Hammer

Need help? Call 800-305-2204

DX-WD1201

W

13

Step 7:

Carefully stand your stand upright.
Push the rubber sleeves (Q) over the remaining metal pins (P). Insert the metal pins (P) into the hole locations

of your choice in the right end (A) and upright (C). Set the adjustable shelf (H) onto the metal pins (P).
Apply the warning label (S) to the top (D). You should be able to read the label when the TV is removed from

your stand. When the TV is in place, it should hide the label. Peel off the backing and apply the label as
shown.

Caution: This is a permanent label intended to last for the life of the product. Once applied, do not try to
remove it. You may damage the finish on the top.

Push a cam cover (R) onto each visible hidden cam (M).
Clean with your favorite furniture polish or a damp cloth. Wipe dry. Your stand is ready to use.

arning: Never use this furniture with a TV

that is too large or too heavy. Severe injury
or death can occur. The TV and furniture
will be unstable and may tip.

• The TV must weigh less than 95 lbs.

• The base of the TV must be able to sit
completely on this shelf.

P and Q

You’l l n e ed:

R (13)P (4) Q (4)

Need help? Call 800-305-2204

14 DX-WD1201

Still need help?

For customer service, call: 800-305-2204 (U.S./Canada markets)
Distributed by Best Buy Purchasing, LLC
7601 Penn Avenue South, Richfield, MN USA 55423-3645
© 2011 BBY Solutions, Inc.
All rights reserved. DYNEX is a trademark of BBY Solutions, Inc. Registered in some countries. All other

products and brand names are trademarks of their respective owners.

Need help? Call 800-305-2204

Certificate of Conformity

1. This certificate applies to the Sauder
Woodworking Product identified by this
instruction booklet.

2. This certificate applies to the compliance of this
product with the CPSC Ban on Lead-Containing
Paint (16 CFR 1303).

3. This product was manufactured by:
Sauder Woodworking Company
502 Middle Street
Archbold, Ohio 43502
[phone]

4. Date of Manufacture: _________________

Lot number: 336968

www.dynexproducts.com [phone]

Distributed by Best Buy Purchasing, LLC

7601 Penn Ave. South, Richfield, MN 55423 U.S.A.

© 2011 BBY Solutions, Inc.

All rights reserved.

DYNEX is a trademark of BBY Solutions, Inc. Registered in some countries. All other products and

brand names are trademarks of their respective owners.

11-0421
ENGLISH