Dynex DX-UA User Manual

FCC Statement

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Your power supply is listed to UL standards and meets all applicable FCC standards. Warning: Changes or modiﬁcations to this unit may cause interference and void the user’s authority to operate the equipment. Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment oﬀ and on, the user is encouraged to try to correct the interference by one or more of the following measures:

1. Re-orient or relocate the receiving antenna.

2. Increase the separation between the equipment and receiver.

3. Consult Dynex customer service at www.dynexproducts.com if the problem still exists. Cautions:

• The charger must attach to the power supply source with a built-in over current protective device (Max. 15A), such as a 15A fuse and branch circuit.

• Make sure the charger is disconnected from the AC outlet and device before adjusting the voltage setting.

• Do not use the charger to power a device that exceeds the maximum power rating. Note: The charger’s voltage must be the same as the voltage your portable device requires. The charger’s current (mA) must be equal to or greater than the current your portable device requires.

90-day limited warranty

For complete warranty, visit www.dynexproducts.com.

© 2009 Dynex. DYNEX and the DYNEX logo are trademarks of Best Buy Enterprise Services, Inc. Other brands and product names are trademarks or registered trademarks of their respective holders. Speciﬁcations and features are subject to change without notice or obligation. ENGLISH 09-0318

Device compatibility list

Brand Model # Voltage Plug size

AGFA ePHOTO CL-30/34/50/307/780/ 780C/1280/1680 6.5V 4.0 x 1.7 CANON A10/20/30/40, ESD-1100 4.2V 4.0 x 1.7 SD790 4.2V 4 x 1.75 A590, A1000 3.3V 2.35 x .73 SX10 6.5V 2.35 x .75 CASIO QV-10A/11/70/100/120/200/300/700/770/780/2000UX/2300UX QV-2400UX/2800UX/2900UX/3000EX/3000Plus/3500EX/4000E, QV-5000SX/5500SX/7000SX/8000SX 6.5V 4.0 x 1.7 EPSON PC 550/600/650/700/750Z/800Z/850Z/2100Z/3000Z/3100Z 6.5V 4.75 x 1.75 FUJIFILM Finepix 50i/1300/1400Z/2300/2400Z/2700Z/2800Z/2900/3800/4800Z, 4900Z/6800Z/6900Z/DX-10, F401/402/601, M603, MX-500/600Z/700/1200 MX-1300/1400Z/1500/1700/2700/2900Z, S1 Pro, S2 Pro, S-304/602/3100 5.0V 4.0 x 1.7 A210/345/350/2650/S-5100 3.3V 2.35 x .75 HP PhotoSmart 120, 315, 318, 320, 612, 620, 720, 850 6.5V 4.0 x 1.7 JVC GZ-MS100, GZ-MG33, GRD-8500 11.0V JVC AP-V KODAK DC40/50/120/200/200plus/210/210plus/215/220/240/240i/260/265/280 DC290/3200z/3400z/DC5000z 6.5V 4.75 x 1.75 DC4800, LS443, DX7430/7440/7590/7630, M863, M1063, M1033, Z1015IS 5.0V 4.0 x 1.7 Z-650/DX-6440/Z-740 3.3V 2.35 x .75 KYOCERA Finecam S3/S3L/S4/S5 5.0V 4.0 x 1.7 MINOLTA Dimage 5/7/7Hi/7i/3D/1500/EX1500/2300/2330z, E201. RD3000, S304/S404 6.5V 4.75 x 1.75 NIKON Coolpix 100/300/600/700/750/800/900/950/990/2000 6.5V 4.75 x 1.75 CoolPix 775/880/885/995/4300/4500/5000/5700/8700 8.4V 4.75 x 1.75 OLYMPUS C-100/120/200Z/211/300Z/320L/700UZ/720UZ/730UZ/960Z/990Z/2000Z C-2020Z/2030/2040Z/2100Z/2500L/3000Z/3020Z/3040Z/4000Z/4040Z/5050Z D-200L/220L/320L/340L/340R/360L/370L/400Z/450L/450Z/460Z/500L/550Z D-600L/620L, E-10/20/20P/100 RS 6.5V 4.75 x 1.75 C-1/1Z/2/40Z/220Z, D-40Z/100/150Z/230/395/540/580 3.3V 4.0 x 1.7 C-50Z, Stylus 300/410 4.2V 4.0 x 1.7 PANASONIC DMC-F7, SDR-57K 5.0V 4.0 x 1.7 DMC-FZ1, VDR-D50, PV-GS90, DMC-LC5/LC40, PVDV - 102/203/402/53 8.4V 4.75 x 1.75 PVL-352/452/453/672 6.5V 4.0 x 1.7 SVAV-25/50A/50S/100, PVDV-103/953, HDC-SD9 8.4V 4.0 x 1.7 PVGS-9/12/15 8.4V 4.75 x 1.75 DMC-LZ3/DMC-LZ2pp 3.3V 2.35 x .75 PENTAX Optio 330RS/430RS 4.2V 4.0 x 1.7 PREMIER DC620/820/1310,/1311/1500/2000 6.5V 4.75 x 1.75 PURE DIGITAL Flip Mino HD, Flip Mino, Flip Ultra, Flip Video 5.0V USB RICOH Caplio PR1/PR10/PR120, RDC-2/2E/7/300/300Z/1500/1700/4200 RDC-4300/5000/5300/6000, 5.0V 4.0 x 1.7 SANYO VPC-MZ1/AZ1 3.3V 4.0 x 1.7 SONY CD200/250/300/400/450/1000, F707/717, FD85/87/90/92/95/97/100 FD200, S50/70/75/85,. CCDTRV-118/128/318/460/608, DCRDVD-101/102 DCRHC-85, DCRTRV-260/460 8.4V Sony L/M SONY P1/2/3/5/9/20/30/31/50/51/71 4.2V Sony S/C Cybershot DSC P8, P10, P32, P52, P72, P92, V-1, 4.2V Sony F/C CCD-TRV138,CCD-TRV338, DCR-DVD Series,DCR-HC Series, DCR-IP Series, DCR-PC Series,DCR-TRV Series, HDR-Series, HDR-CX7, HDR-UX Series, HDR-HC Series,DCR-SR Series, HDR-SR10 8.4V Sony A/P/F TOSHIBA PDR-M1/M3/M4/M5/M11/M21/M25/M60/M61/M65/M70/M71/M81 5.0V 4.0 x 1.7

DX-UA Universal Camera/Camcorder AC Charger

Congratulations on your purchase of the DX-UA Dynex Universal Camera/Camcorder AC Charger. The charger can power digital cameras, camcorders, and other portable electronic devices that require 3.3V, 4.2V, 5.0V, 6.5V, 8.4V, or 11.0V DC power. It is fully regulated using high eﬃciency switching technology and features overload and short circuit protection. The charger comes with connectors to ﬁt diﬀerent digital cameras, camcorders, and other electronic devices. Additional connectors are available from Dynex by contacting customer service.

3.3V

4.2V

5.0V

6.5V

8.4V

9.5V 11V

QUICK SETUP GUIDE

Important safety instructions—Save these instructions

This document contains important safety and operating instructions for your AC power charger. Before using your charger, read all instructions and cautionary markings on the product.

Package contents

• DX-UA charger

• AC adapter

• Center pin positive connectors

• Quick Setup Guide

Note: The center pin connectors are set to a center pin positive alignment. If your device needs a center pin negative alignment, do not use this charger.

Input

Output voltage switch

Power light

Universal AC Adapter Model SUP-60LX

3.3v

4.2v

5.0v

6.5v

8.4v

11.0v

Check your device‘s user manual for more information on what type of alignment your device requires.

+ -

Positive alignment

- +

Negative alignment

Output socket

Using a connector 1 Select the appropriate connector and attach it to the output socket

at the end of the output cord. To identify the correct connector for your device, see the Device Compatibility List. If you are not sure, use the connector that ﬁts the power jack of your device. The two-pin connectors ﬁt into the socket only one way. One pin is larger than the other.

Note: One pin is larger than

the other. Do not force the pins. Check your device‘s user manual

Connector

Output socket

for information regarding the input voltage your device requires.

2 Set the Output voltage switch to the correct voltage for your device. The voltage can be between 3.3 and 11V DC and no more than

2100 mA of current. If the exact voltage for your device is not listed and is less than 11V, try setting the voltage switch to the nearest voltage that is lower than the voltage for your device. If the device does not work, disconnect the connector from the device, reset the voltage switch to the next higher setting, then re-connect. Do not

continue trying higher settings because they may damage your

device or the charger.

Note: The Micro USB tip works with any compatible cell phone.

Note: The DX-UA’s current (mA) must be equal to or greater than the

current your portable device requires. Remember 1A = 1000mA, 0.5A = 500mA. Use the following chart to determine the output current from the DX-UA:

Output Voltage Max. Current

3.3V 2.1A

4.2V 2.0A

5.0V 1.9A

6.5V 1.7A

8.4V 1.6A

11.0V 1.5A

Resetting the charger Caution: If the power light turns oﬀ, check the power source. If the

power source is working, the output current may be beyond the AC charger’s speciﬁcations and overload protection has been activated.

To reset the charger: 1 Unplug the DX-UA from the AC outlet and the device you are

powering. Wait 10 seconds. 2 Plug the DX-UA into the AC outlet again. If the indicator remains oﬀ, there may be a problem with the AC charger. Contact Dynex for assistance.

Speciﬁcations

AC adapter input: 100-240V AC, 50-60Hz AC adapter output: 15V DC, 1.0A DX-UA input: 12-15V DC Output rating: 3.3 / 4.2 / 5 / 6.5 / 8.4, or 11.0V DC DC cord length: 8.2 ft. (2.5 m) Operation Temperature: 32°F to 113°F (0°C to 45°C) Storage temp.: -4°F to 140°F (-20°C to 60°C) Dimensions: 4 × 2.1 × 1.4 inches (10.16 × 5.33 × 3.56 cm)

Plug number and size (diameter)

4.0 mm x 1.7mm

4.75 mm x 1.75 mm

2.35 mm x .75mm Sony L/M Sony S/C Sony F/C Sony A/P/F JVC AP-V Female USB Tip - 5V only Micro USB Tip - 5V only

Safety warnings and cautions

Warning: To reduce the risk of ﬁre or shock hazard, do not expose

this product to rain or moisture. Caution: To reduce the risk of electric shock, do not remove the cover or back. No user serviceable parts inside. Refer servicing to Dynex.

Contact Dynex:

For customer service please call 1-800-305-2204 www.dynexproducts.com Distributed by Best Buy Purchasing, LLC 7601 Penn Avenue South, Richﬁeld, Minnesota, U.S.A. 55423-3645